You are on page 1of 1

Rexam : CRM 57mm(206) Operation Specifications

1 of 1

http://bcecrm.rexam.com/contents/seam_specifications/57mm(206)_op...

57mm (206) DOUBLE SEAM SPECIFICATION FOR BEER &


BEVERAGE CANS
Operation specifications
1ST OPERATION SPECIFICATIONS
PARAMETERS

SETUP SPECIFICATIONS

1st Operation Seam Thickness

2.08mm +/- 0.10mm

1st Operation Seam Length

2.00mm +/- 0.05mm

1st Operation Countersink Depth

6.36mm +/- 0.15mm Maximum

2ND OPERATION SPECIFICATIONS


PARAMETERS

SETUP SPECIFICATIONS

2nd Operation Countersink Depth

6.36mm +/- 0.15mm

2nd Operation Seam Length

2.60mm +/- 0.15mm

2nd Operation Seam Thickness

As Per Matrix +/- 0.05mm


Finished Seam Body Wall Impression
Should Be Visible & Continuous

2nd Operation Body Hook Length

1.60mm +/- 0.20mm

End Hook Length

1.60mm +/- 0.20mm

Actual Overlap

0.76mm Minimum

Body Hook Butting

72% to 92% Steel Cans


72% to 97% Aluminium Cans

Seam Gap (Directly After Seaming)


Optical Only

0.1mm Maximum (Aim For 0.05mm)

End Hook Tightness Rating

90% Wrinkle Free

Free Space

0.13mm +/- 0.05mm

Finished Can Height

Nominal Can Height +/- 0.3mm

Nominal
Flange
Thickness

Actual Measured End Thickness (In MM Including Lacquer)


0.2950.2900.2850.2800.2750.2700.2650.2600.2550.2500.2450.2400.2350.2300.2250.220

0.200

1.41 1.40 1.38 1.37 1.36 1.34 1.33 1.31 1.30 1.28 1.26 1.25 1.24 1.22 1.21 1.19

0.195

1.40 1.39 1.37 1.396 1.35 1.33 1.32 1.30 1.29 1.27 1.25 1.24 1.23 1.21 1.20 1.18

0.190

1.39 1.38 1.36 1.35 1.34 1.32 1.31 1.29 1.27 1.26 1.24 1.23 1.22 1.20 1.19 1.17

0.185

1.38 1.37 1.35 1.34 1.33 1.31 1.30 1.28 1.26 1.25 1.24 1.22 1.21 1.19 1.18 1.16

0.180

1.137 1.36 1.34 1.33 1.32 1.30 1.29 1.27 1.25 1.24 1.23 1.21 1.20 1.18 1.17 1.15

0.175

1.36 1.35 1.33 1.32 1.31 1.29 1.27 1.26 1.24 1.23 1.22 1.20 1.19 1.17 1.16 1.14

0.170

1.35 1.34 1.32 1.31 1.30 1.28 1.26 1.25 1.24 1.22 1.21 1.19 1.18 1.16 1.15 1.13

0.165

1034 1.33 1.31 1.30 1.29 1.27 1.25 1.24 1.23 1.21 1.20 1.18 1.17 1.15 1.14 1.12

0.160

1.33 1.32 1.30 1.29 1.27 1.26 1.24 1.23 1.22 1.20 1.19 1.17 1.16 1.14 1.13 1.11

0.155

1.32 1.31 1.29 1.28 1.26 1.25 1.24 1.22 1.21 1.19 1.18 1.16 1.15 1.13 1.12 1.10

0.150

1.31 1.30 1.28 1.27 1.25 1.24 1.23 1.21 1.20 1.18 1.17 1.15 1.14 1.12 1.11 1.09

0.145

1.30 1.29 1.27 1.26 1.24 1.23 1.22 1.20 1.19 1.17 1.16 1.14 1.13 1.11 1.10 1.08

0.140

1.29 1.28 1.26 1.25 1.24 1.22 1.21 1.19 1.18 1.16 1.15 1.13 1.12 1.10 1.09 1.07

0.135

1.28 1.27 1.25 1.24 1.23 1.21 1.20 1.18 1.17 1.15 1.14 1.12 1.11 1.09 1.08 1.06

0.130

1.23 1.22 1.20 1.19 1.17 1.16 1.14 1.13 1.11 1.10 1.08 1.07 1.05

0.125

1.20 1.19 1.17 1.16 1.14 1.13 1.11 1.10 1.08 1.07 1.05 1.04
Seam thickness tolerance range = +/- 0.005mm.
Refer to can supplier for nominal can flange thickness.

Should any setting adjustment be required, refer to set up specifications and procedures sheet

The Quality Of The Double Seam Is The Responsibility Of The Filler

9/12/2012 12:15 AM

You might also like