You are on page 1of 2

MODEL QUESTIO]Y PAPER

FOUR YEAR B.TECH DEGREE END EXAMINATION


FIFTH SEMESTER EXAMINATION
MECHANICAL ENGINEERING
pEsrGN 9r' MACHINE_MEMBEB$-I (pMM-t)
(scHEME- 2013)

J'ime:3

Hours

Max.Marks:70

Note : 1. Question No. I is compulsory and it must be answered first in sequence at one
place onll,Answer any FOUR florn the remainin-u.
2. Design Data hand book is permitted

1.

Answerthe

tbllowing:

(10 x

10)

(a) What is l'actor of safety?


(b) State the Maximum principal stress theory.
(c) What is theoretical stress concentration factor?
(d) Define notch sensitivity.
(e) Define nomenclature of the screw thread.
(f) What are the various modes of failure of a riveted joint'7
(g) What is throat in case of welded joint?
(h) Define key.

(i)
fi)

2.

What are the types of belt drive?


What are the applications of knuckle joint?

(a) What are the major criteria for selecting material in machine design ?

(b) The stresses at a point in a body are ox:91 MN/m 2: oy:21 MN/m 2;Txy:84

MN/m2;yield point stress:280 MNAn 2: find the factor of safety:

(i)

By the maximum shear stress theory.

(2) By the distortion energy theory.

3.

(a) what is stress concentration? And how you can reduce stress concentration?

(b) A hot rolled SAE 1025 steel shaft is subiected to a variable bending moment from
50 N-rn

to 100 N-m and axial Ioad varl,ing from 5000 N to

15000 N. the maxirnum

bending moment occurs at the same time when the n'raximum axial load occurs.
determine the required diameter of rod for a FS:2

(a) what is bolts of uniform strength?

(b) For supportin-e the travelling crane in a workshop. the brackets are fixed on
colunrns as shorvn

steel

in Fig-I. The maximum load that comes on the bracket is l2KN

acting verticallv at a distance o1'400 mm fiom the face of the coiumn. The vertical face

of the bracket is secured to a colurnn by four bolts. in two rows (two in each row) at a
distance

of 50 mm from the lower edge of the bracket. Determine the size of the bolts

the permissible value of the tensile stress for the bolt material

if

is 84 Mpa. Also find the

cross-section of the arm of the bracket rvhich is rectangular.

P.'f.o

i{_ .tiili i.il.:i

_*,"1

T-r
;-!

-.

r..\

ritr:i
i

i-L

t'"1
,i

--rJ

t::i'--.J

Figure.l
.).

a) Two mild steel tie rods having width 200 mm and thickness i2"5 mm are to
connected by means of riveted butt

be

joint with double cover plates. Design the ioint if

the perrnissible stresses are 80 MPa in tension,65 MPa

in shear and 160 lv{Pa in

crushing. Draw the figure of the joint.

b) A bracket canying a load of 15 kN is to be welded as shown in figure-2. Find the


size of weld required

if the allowable

shear stress is not to exceed 80 Nr'mrn2.

skN

6. Design a cotter joint to connect piston rod to the crosshead of a double acting
engine. The diameter

of the cylinder is

300mm and steam pressure

ailowable stress for the nraterial of cotter and piston rod are as

is 1 N/

steanr

mnr2. l'he

clt :50MPa, r:40 MPa

and

oc

- 84Mpa.

7.

A leather belt 9 mm x 250 mm is used to drive a cast iron pulley 900 mm in diameter

336 r.p.rn.

at

If the active arc on the smaller pulley is 120'and the stress in tight side is 2 N{Pa.

find the po\\'er capacitl, of the belt. The density' of leather may be taken as 980 kg/m3. and thc
coefflcient of fi'iction of leather on cast iron is 0.35.

You might also like