You are on page 1of 6

320B & 320B L Excavators 5GW00001-UP (MACHINE) POWERED BY 3066 En...

Pgina 1 de 6

Fechar o SIS
Tela anterior
produtos: EXCAVATOR
Modelo: 320B L EXCAVATOR 5GW00250
Configurao: 320B & 320B L Excavators 5GW00001-UP (MACHINE) POWERED BY 3066 Engine

Teste e Ajustes
308B, 311B, 312B, 315B, 317B, 318B, 320B, 322B, 325B, 330B, M325B and W330B
Excavators Engine and Pump Control
Nmero de Mdia -RENR1998-06

Data de Publicao -01/10/2004

Data de Atualizao -06/10/2004

i01768419

Using Service Mode


SMCS - 7569

Illustration 1

g00904377

Monitor Panel
(1) Action lamp
(2) Character display

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 12/11/2015

320B & 320B L Excavators 5GW00001-UP (MACHINE) POWERED BY 3066 En... Pgina 2 de 6

(3) Fuel gauge


(4) Hydraulic oil temperature gauge
(5) Engine coolant temperature gauge
(6) Charge alert indicator
(7) Alert indicator for the engine oil pressure
(8) Alert indicator for the hydraulic oil temperature
(9) Alert indicator for the engine coolant temperature
(10) Clogged air filter indicator
(11) Indicator for a hydraulic return filter that is clogged
(12) Controller alert indicator
(13) Monitor alert indicator
(14) Air heater indicator
(15) Fuel level alert
(16) Hydraulic oil level alert
(17) Engine oil level alert
(18) Alert indicator for the engine coolant level
(19) Power mode switch
(20) AEC switch
(21) Travel speed control switch
(22) Travel alarm cancel switch
(23) Boom priority mode switch
(24) Swing priority mode switch
(25) Fine control mode switch
(26) User mode switch
(27) Pictograph symbol

The Electronic Monitor Panel will activate. Then, the monitor will display the output that is received
from the controller. The Controller Service Program is divided into five functions. Each function is
listed:
Alerting the presence of abnormal engine operation
Displaying the machine conditions (engine speed, hydraulic oil temperature, power shift
pressure, etc)
Service codes: 10 to 21.
Displaying the existing electronic problems or the past electronic problems
Service codes: 18, 19, 1c, 1d

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 12/11/2015

320B & 320B L Excavators 5GW00001-UP (MACHINE) POWERED BY 3066 En... Pgina 3 de 6

The electronic control components are adjusted and tested. The adjustment codes are listed: 70
and 71. The test codes are listed: 60, 61, 62, 66 and 67.
Changes in various defaults in the controller
Service codes: 80 to 8A
You should depress the switches on the monitor panel in order to start up the service program or the
switches are depressed in order to change the functions. The corresponding switch and/or switches
should be depressed until the required function is displayed on the character display.

Start-Up Of The Service Mode

Illustration 2

g00662936

Electronic Monitor Panel


(2) Character display

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 12/11/2015

320B & 320B L Excavators 5GW00001-UP (MACHINE) POWERED BY 3066 En... Pgina 4 de 6

(22) Travel alarm cancel switch


(23) Boom priority mode switch
(24) Swing priority mode switch
(25) Fine control mode switch
(26) User mode switch

Note: The engine can be running or the engine can be stopped, when the "Service Mode" is started.
When the engine is stopped, the starter switch must be in the ON position. You should know the
procedure to start up the "Service Mode" in advance.
1. The following switches should be depressed and held for 2 seconds or more simultaneously:
travel alarm cancel switch (22), fine control mode switch (25) and user mode switch (26) .
2. The time display and the dial display on the character display (2) will change to a "0" and a
"0". The left character position will flash.
3. You need to enter the following security code: OE 32 3A.
Note: The security code must be entered within 10 seconds after the first procedure (1).
Otherwise, the time display will return. You should learn the procedure of entering the security
code in advance.
4. The procedure to input information is listed:
a. The figure that is blinking on the character display (2) can be changed. In order to
change the figure, you should depress the boom priority mode switch (23) or the swing
priority mode switch (24).
The figure that is blinking increases (Boom priority mode switch (23) )
The figure that is blinking decreases (Swing priority mode switch (24) )
The character position that is blinking can be shifted by depressing the fine control mode
switch (25) or the user mode switch (26).
The character position that is blinking shifts to the right (Fine control mode switch
(25) ).
The character position that is blinking shifts to the left (User mode switch (26) ).
5. After you enter the security code, the service mode is activated by depressing and holding the
following switches for 2 seconds or greater: travel alarm cancel switch (22), fine control mode
switch (25) and user mode switch (26). The service mode is automatically activated 10 seconds
after the security code is entered.
6. Now, the "Service Mode" is activated and the character display (2) will display "10" on the left
two character positions and "1" on the right character position.

Changing The Service Mode


1. The boom priority mode switch (23) or the swing priority mode switch (24) is pressed in order
to change the figures that are blinking on character display (2) .

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 12/11/2015

320B & 320B L Excavators 5GW00001-UP (MACHINE) POWERED BY 3066 En... Pgina 5 de 6

The figure that is blinking increases (Boom priority mode switch (23) )
The figure that is blinking decreases (Swing priority mode switch (24) )
2. The position that is blinking on the character display (2) can be shifted by depressing the fine
control mode switch (25) and the user mode switch (26) .
The position that is blinking shifts to the right (Fine control mode switch (25) )
The position that is blinking shifts to the left (Swing priority mode switch (24) )
Note: Refer to the chart of Service Codes for selecting the functions for the "Service Mode".
Table 1
Service
Code

Function

10

Automatic Travel Speed Change

11

Low Temperature Control

12

Engine Speed

13

Engine Coolant Temperature

14

Hydraulic Oil Temperature

16

Digital Input

17

Software Version

18

Real Time Error Code

19

Error Log

1a

Engine Speed Dial Setting Check

1b

Model Name and Engine Type

1c

Real Time Error Code (ATT)

1d

Error Log (ATT)

20

Power Shift Pressure Command Signal

21

Displays Higher Delivery Pressure Of Main Pumps

60

Proportional Reducing Valve Sweep Test

61

Governor Actuator Sweep Test

62

ON/OFF Test Of Digital Output

66

Fixed Power Shift Pressure

67

Engine Speed Change

70

Governor Actuator Calibration

71

Proportional Reducing Valve Calibration

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 12/11/2015

320B & 320B L Excavators 5GW00001-UP (MACHINE) POWERED BY 3066 En... Pgina 6 de 6

80

Setting Of Hydraulic Oil Type Mineral Or Biological

81

Setting Of AEC Speed

82

Setting Of AEC Delay Time

83

Setting Of Memory Mode

84

Setting Of Reduced Horsepower For Attachment Pump

85

Setting Of Engine Speed For Low Idle Switch

86

Setting Of Pump Quantity For Hammer Mode

87

Setting Of Hammer Circuit Pressure

88

Setting Of Pump Flow For Hammer Mode

8a

Setting Of Power Offset For Attachment Pump

8b

Change Of Preset Conditions Of Main Pump Output

8c

Change Of Upper Limits Of Preset Conditions Of Main Pump Output (Such As


Power Mode Or Engine Speed At Dial Position 10)

Procedure To Stop The Service Mode


Note: One of the following two methods should be used.
1. Turn the starter switch to the OFF position.
2. The following switches should be depressed and held simultaneously for 2 second or more:
(22) Travel alarm cancel switch
(25) Fine control mode switch
(26) User mode switch
The service mode has been stopped, if the character display shows the position of the engine
speed dial on the right two character positions and the time is shown on the left four character
positions.
Direitos Autorais 1993 - 2015 Caterpillar Inc.

Thu Nov 12 22:22:11 UTC-0200 2015

Todos os Direitos Reservados.


Rede Particular Para Licenciados SIS.

https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 12/11/2015

You might also like