You are on page 1of 18

masCorrect

Q.1) Size of water piping shall be based on the total _________


A.
B.
C.
D.
Wrong

water consumption
water demand (your answer)
water potability
none of the above

Q.2) Water closet bowls for________ use shall be elongated bowl types equipped with openfront seats.

A.
B.
C.
D.
Wrong

public (correct answer)


private (your answer)
government
none of the above

Q.3) Wastewater drain for _________ cupsink at church altar & baptisteries font outlet shall
discharge direct to the ground & not connected to any sanitary or drainage system.

A.
B.
C.
D.
Wrong

holy sink (your answer)


lavatory
Baptismal shrine
Sacrarium (correct answer)

Q.4) Tunnels shall have: the following except


a clear height of 0.6m above the pipe & shall be limited in length to 1/2 the depth of
the trench. (your answer)
B. driven pipes shall have at least one pipe size larger than the pipe to be laid
shall be back-filled in thin layers of 0.3m above the top of the pipe with clean earth
C. which shall not contain stones, boulders, cinders or other materials which can
damage or break the pipes or cause corrosive action. (correct answer)
D. none of the above
Wrong
A.

Q.5)

the

minimum cross sectional area at the seat of the control valve or the supply pipe or
tubing which feeds the device outlet. If two or more lines supply one outlet, the effective
opening shall be the sum of the cross-sectional areas of the individual supply lines or the
area or the single outlet, whichever is smaller.

A. effective opening (correct answer)


B. effective depth

C. effective area (your answer)


D. effective invert
Unanswered
Q.6) Suspended cast iron soil pipe shall be supported at not more than ____m intervals, except
that pipe exceeding 1.5m length may be supported at not more than _____m
intervals. Supports shall be adequate to maintain alignment & to prevent sagging & shall be
placed within 0.45m of the hub or joint.

A. 1.5/ 3 (correct answer)


B. 1.5/ 4
C. 3/ 1.5
D. 4/ 1.5
Unanswered
Q.7)

No water closet or bidet shall be set closer than ______m from its center to any side of
the wall or obstruction or closer than ______m center to center to any similar fixture.

A. .375 / 0.75 (correct answer)


B. .375 / 0. 70
C. .40 / 0.70
D. .50 / 0.60
Unanswered
Q.8) Lead Pipe

- shall be supported at by____________for entire lengthwith hangers

properly spaced.

A. Stiff aluminum or wooden backing


B. stiff metal or wooden backing (correct answer)
C. stiff plastic or metal sheet
Unanswered
Q.9)

Fixtures having concealed slip joint connections shall be provided with an access panel
or utility at least ______m in its least dimension for inspection & repair.

A. 0.30 (correct answer)


B. 0.20
C. 0.10
D. 0.40
Unanswered
Q.10) Excessive water pressure water pressure greater than ____ Kpa
A. 551 (correct answer)
B. 552
C. 553
D. 554
Unanswered

Q.11)

drains shall have a waterway equivalent area of the tailpiece meaning, the sum of all
the areas of the perforation of the strainer is equivalent to the outlet area.

A. Strainers serving bathub


B. Strainers serving shower (correct answer)
C. Strainers serving lavatory
D. none of the above
Unanswered
Q.12) Copper Tubing - shall be supported at approximately ________m intervals for piping
38mm diameter & smaller & _______m intervals for piping 51mm & larger in dia.

A. 1.8/ 3.0 (correct answer)


B. 1.9/ 3.5
C. 1.5 / 2.5
D. none of the above
Unanswered
Q.13)

Continuous waste fixture tailpiece connections were exposed or accessible may be of


seamless drawn brass not less than Ga. 20 B&S or ______mm thk.

A. 0.90
B. 0.80 (correct answer)
C. 0.70
D. 0.60
Unanswered
Q.14) All porcelain enamel surfaces on plumbing fixtures shall be __________
A. mold resistant
B. acid resistant (correct answer)
C. corrosion resistant
D. none of the above
Unanswered
Q.15)

All pipe determinations shall be based on eighty percent (___) the reduced pressure.

A. 70%
B. 60%
C. 80% (correct answer)
D. 90%
Unanswered
Q.16) ______________ must be supported at least every other joint except that when the developed
length between supports exceeds 1.2m, they shall be provided at each joint.

A. Couplings and compression joints


B. Hubless or compression gasket joints (correct answer)
C. Caps and plugs
D. none of the above
Unanswered
Q.17)

- shall be supported by stiff metal or wood backing with hangers in its entire
length for small-size tubings up to 38mm diameter &without backings but with spaced
metal hangers at approved spacingfor larger-size tubings.
____________

A. steel tube
B. plastic tube (correct answer)
C. aluminum tube
D. concrete tube
Unanswered
Q.18) ________ m max. length of supply piping.
A. 61 (correct answer)
B. 62
C. 63
D. 64
Unanswered
Q.19)

If

water closets or other plumbing fixtures are installed in the buildings where there is no
sewer within a reasonable distance, suitable provision shall be made for disposing of the
building sewage by some accepted method of sewage treatment and disposal, such as
______________

A. WASTE TANK
B. SEPTIC TANK (correct answer)
C. SEWAGE DISPOSAL SYSTEM
D. NONE OF THE ABOVE
Unanswered
Q.20) Drainage pipes shall be run in practical alignments & at a uniform slope between
manholes of not less than ______________ toward the point of disposal.

A. 20mm/m or 2% (correct answer)


B. 30mm/m or 3%
C. 40mm/m or 4 %
D. 10mm/m or 1 %
Unanswered
Q.21)

Changes in direction of piping shall be made by the use of approved pipe fittings & shall be
the angles presented by the following except

A. 22 degrees bend
B. 45 degrees bend
C. 60 degrees bend or other approved fittings of longer sweeps
D. 30 degress bend (correct answer)
Unanswered
Q.22) All piping of plumbing systems shall be of durable ____________-APPROVED materials, free
from defective workmanship, designed and constructed by Registered Master Plumbersto
ensure satisfactory service.

A. NAMPAP (correct answer)


B. DILG
C. DPWH
D. DENR
Unanswered
Q.23)

a physical separation, which may be a low inlet into the indirect waste receptor from the
fixture, appliance or device indirectly connected

A. AIR SEPARATION
B. AIR BREAK (correct answer)
C. AIR DEVISOR
D. NONE OF THE ABOVE
Unanswered
Q.24) a length of soil or waste stack corresponding in the general to a storey height, but in no case
less than 2.43m within which the horizontal branches from one floor or storey of a
building are connected to the stack.

A. BRANCH INTERVAL (correct answer)


B. INTERVAL
C. BRANCH
D. LENGTH
Unanswered
Q.25)

Each family dwelling unit on premises abutting on a sewer or with a private sewer-disposal
system shall have at least ___ water closet and ___ kitchen-type sink

A. 1,2
B. 1,1 (correct answer)
C. 2,1
D. 2,3
Unanswered
Q.26)

Horizontal drainage lines connecting to a vertical stack shall enter through the
following except,

A. 45 wye branches
B. combination wye & 1/8 bend branches
C. 30 wye bend (correct answer)

D. or other approved fittings of longer sweeps.


Unanswered
Q.27)

Horizontal drainage lines connecting to other horizontal drainage lines shall enter through
the following given below except:

A. 45 wye branches
B. combination wye & 1/8 bend branches
C. or other approved fittings of longer sweeps.
D. 30 wye bend (correct answer)
Unanswered
Q.28) Birth of plumbing profession in the Philippines
A. INTRAMUROS (correct answer)
B. BARASOAIN
C. BATAAN
D. CEBU
Unanswered
Q.29)

Vertical drainage lines connecting to other horizontal drainage line shall enter through

A. 45 wye branches
B. or other approved fittings of longer sweeps.
C. 60 degree branches or offsets (only for pipes installed in true vertical position
D. 45 degree branches (correct answer)
Unanswered
Q.30)

No Drainage Fitting shall use:

A. Double hub fitting for leak-caulked joint in vertical position


B. Single or double tee branch
C. Single or double tapped tee branch
D. Side inlet quarter bend, Running thread, band or saddle
E. all of the above (correct answer)
Unanswered
Q.31)

____________________may be used on vertical lines as a fixture connection. (approved


stainless steel bands with neoprene gaskets for jointing hubless cast iron soil pipes are
acceptable for use)

A. single hub sanitary tapped tee


B. double hub sanitary tapped tee (correct answer)
C. triple hub sanitary tapped tee
D. none of the above
Unanswered
Q.32) a minimum standard quantity of plumbing fixtures that discharge wastes into a plumbing
installation

A. plumbing unit (correct answer)


B. plumbing fixtures
C. plumbing system
D. plumbing minimum
Unanswered
Q.33)

In PROHIBITED FITTINGS & PRACTICES under this rule no ____________ shall be


threaded.

A. GI soil pipe
B. cast iron soil pipe (correct answer)
C. PVC soil Pipe
D. none of the above
Unanswered
Q.34) Further, a _________ and bathtub or shower shall be installed to meet the basic requirements
of sanitation and personal hygiene.

A. SINK
B. LAVATORY (correct answer)
C. BASIN
D. NONE OF THE ABOVE
Unanswered
Q.35)

fixture directly connected to the drainage system shall be equipped with a ________.

A. VENTILATING SYSTEM
B. WATER-SEALED TRAP (correct answer)
C. SOIL PIPES
D. WASTE PIPES
Unanswered
Q.36) Any such pipe or piping _______mm or larger in diameter may have a slope of 10mm/m or
1% provided it is approved by Administrative Authority

A. 100 mm
B. 102 mm (correct answer)
C. 101 mm
D. 104 mm
Unanswered
Q.37)

Water pipes & fittings with a lead content that exceed ____ shall be prohibited & shall not
be used in potable piping systems.

A. 8% (correct answer)
B. 9%

C. 10%
D. 11%
Unanswered
Q.38) Water Closet & Urinal Tanks shall be equipped with a listed ________ & shall be installed
with the critical level at least 25mm above the full opening of the overflow pipe.

A. corporation cock
B. gatevalve
C. ballcock (correct answer)
D. none of the above
Unanswered
Q.39)

THE TOTAL NUMBERS OF SET OF SANITARY/ PLUMBING PLANS


REQUIRED BY THE BUILDING OFFICIAL WHEN APPLYING FOR PERMIT

A. 4
B. 5
C. 3
D. 6 (correct answer)
Unanswered
Q.40) THE SANITARY AND PLUMBING PERMIT WILL BE REVOKE IF THE
PROJECT HAS BEEN ABANDONED OR SUSPENDED FOR HOW MANY DAYS
A. 120 (correct answer)
B. 60
C. 30
D. 100
Unanswered
Q.41)

The quantity of water required to be supplied to every plumbing fixture shall be represented
by ____________

A. Fixture Units FU
B. Fixture drain FD (correct answer)
C. Fixture Trap FT
D. none of the above
Unanswered
Q.42) the minimum airgap for Effective openings not greater than 25mm in diameter. affected by
walls

A. 2 times diameter of effective opening


B. 4 times diameter of effective opening
C. 5 times diameter of effective opening
D. 3 times diameter of effective opening (correct answer)
Unanswered

Q.43)

the minimum airgap for Effective openings not greater than 25mm in diameter. not affected by
walls

A. 3 times diameter of effective opening


B. 2 times diameter of effective opening (correct answer)
C. 4 times diameter of effective opening
D. 5 times diameter of effective opening
Unanswered
Q.44) THE MINIMUM HEIGHT REQUIRED FROM THE FINISH GRADE LINE THE
SIAMESE INLET CONNECTION OF A STANDPIPE
A. 2.0 M
B. 1.2 M (correct answer)
C. 1.5 M
D. 2.5 M
Unanswered
Q.45)

The minimum air gap for Over rim bath fillers & other fixtures with effective openings not
greater than 25mm in diameter. affected by walls

A. 76mm (correct answer)


B. 77mm
C. 78mm
D. 79mm
Unanswered
Q.46) The minimum air gap for Over rim bath fillers & other fixtures with effective openingsnot greater
than 25mm in diameter. not affected by walls

A. 54mm
B. 53mm
C. 52mm
D. 51mm (correct answer)
Unanswered
Q.47)

The minimum air gap for Lavatories & other fixtures with effective openings not greater than
13mm in diameter if not affected by wall

A. 25 (correct answer)
B. 24
C. 23
D. 22
Unanswered
Q.48) The minimum air gap for Lavatories & other fixtures with effective openings not greater than
13mm in diameter if affected by walls

A. 36mm
B. 37mm
C. 38mm (correct answer)
D. 39mm
Unanswered
Q.49)

the minimum air gap for Sinks, laundry trays, goosenecks bath faucets & other fixtures
with effective openings not greater than 19mm in diameter. if not affected by wall

A. 40mm
B. 39mm
C. 38mm (correct answer)
D. 37mm
Unanswered
Q.50) the minimum air gap for Sinks, laundry trays, goosenecks bath faucets & other fixtures
witheffective openings not greater than 19mm in diameter. if affected by wall

A. 56mm
B. 57mm (correct answer)
C. 58mm
D. 59mm
Unanswered
Q.51)

THE EXPIRATION OF THE PERMIT FOR SANITARY / PLUMBING WILL BE


EXPIRED AFTER HOW MANY YEARS FROM THE DATE OF ISSUANCE

A. 2
B. 1 (correct answer)
C. 1.5
D. 3
Unanswered
Q.52) THE DRAWINGS, SPECIFICATION, CALCULATIONS AND ETC FOR
PLUMBING / SANITARY PERMIT WILL BE SIGNED BY A a Registered &
Licensed
A. DRAINAGE ENGINEER
B. MASTER PLUMBER (correct answer)
C. SANITARY ENGINEER
D. ARCHITECT
Unanswered
Q.53)

Restaurant kitchen & other special-use sink may be made of approved-typed sheet steel not
less than Ga.16 U.S. B&S or 1.6mm thk.

A. bonderized & galvanized (correct answer)

B. aluminum
C. steel
D. none of the above
Unanswered
Q.54) No urinal shall be set closer than _________m center to center
A. 0.70
B. 0.60 (correct answer)
C. 0.50
D. 0.65
Unanswered
Q.55)

No building sewer or other drainage pipings or part thereof, constructed of materials other
than that approved for use under or within the building, shall be installed under or within
_____ m of any building or structure, nor less than 0.3m below the finish ground
surface

A. 0.60 (correct answer)


B. 0.40
C. 0.30
D. 0.20
Unanswered
Q.56) No building water service pipe shall be less than _____mm in diameter
A. 21
B. 20
C. 25
D. 19 (correct answer)
Unanswered
Q.57)

Inadequate water pressure water pressure less than _____ Kpa

A. 103 (correct answer)


B. 104
C. 105
D. 106
Unanswered
Q.58) In Screwed Pipe - IPS shall be supported at approximately _______m intervals for piping
19mm diameter & smaller & _______m intervals for piping 25mm & larger in diameter.

A. 3.5 / 3.0
B. 3.0 / 3.5
C. 3.6/ 3.0
D. 3.0 / 3.6 (correct answer)
Unanswered

Q.59)

In Ground
- piping buried on the ground shall be laid on the ______ for its entire
length, except where concrete cradle support is provided which is adequate & approved by
the Administrative Authority.

A. firm bed (correct answer)


B. strata
C. compacted earth
D. none of the above
Unanswered
Q.60) for EXCRETA DRAINAGE SYSTEM No Vitrified Clay Pipes or Fittings for building drain or
sewer shall be used above ground or whenever piping is pressurized by a pump or ejector.
They shall be kept ______m below finish ground level.

A. 0,30 (correct answer)


B. 0.40
C. 0.50
D. 0.60
Unanswered
Q.61)

for EXCRETA DRAINAGE SYSTEM No Galvanized Wrought Iron orGalvanized Steel


Pipe shall be used underground & shall be kept at least _____mm above ground.

A. 155
B. 152 (correct answer)
C. 153
D. 154
Unanswered
Q.62) for vertical piping,Screwed Pipe - Iron Pipe Size (IPS) shall be supported at not less
than every other storey

A. drift
B. height (correct answer)
C. level
D. dimension
Unanswered
Q.63)

for vertical piping, _________ - shall be supported at each storey or at amaximum


intervals of 3m o.c.

A. lead tubing
B. copper tubing (correct answer)
C. steel tubing
D. g.i. tubing
Unanswered
Q.64) for vertical piping, cast iron pipes- Bell & Spigot & Hubless pipe shall be

supported at_____ or closer.

A. every 2 storey
B. every storey (correct answer)
C. every 3 storey
D. every 4 storey
Unanswered
Q.65)

FOR THE SET OF SANITARY/ PLUMBING PLANS REQUIRED BY


THE BUILDING OFFICIAL WHEN APPLYING FOR PERMIT HOW
MANY SET OF DRAWINGS WILL BE RETURNED ON THE
APPLICANT

A. 1
B. 2 (correct answer)
C. 3
D. 4
Unanswered
Q.66) FOR THE SET OF SANITARY/ PLUMBING PLANS REQUIRED BY THE
BUILDING OFFICIAL WHEN APPLYING FOR PERMIT HOW MANY SET OF
DRAWINGS WILL BE PROVIDED FOR THE ADMINISTRATIVE AUTHORITY
A. 1 (correct answer)
B. 4
C. 3
D. 2
Unanswered
Q.67)

FOR THE SET OF SANITARY/ PLUMBING PLANS REQUIRED BY


THE BUILDING OFFICIAL WHEN APPLYING FOR PERMIT HOW
MANY SET OF DRAWINGS WILL BE KEPT IN THE JOB SITE

A. 2
B. 3
C. 1 (correct answer)
D. 4
Unanswered
Q.68) fixture unit Lawn Sprinklers (standard type, each head)
A. 1 (correct answer)
B. 2
C. 1.5
D. 2.0
Unanswered
Q.69)

fixture unit Water Closet (economical flush) private use

A. 5
B. 4
C. 3
D. 2.5 (correct answer)
E. 2
Unanswered
Q.70) fixture unit of Urinal (stall & wall)
A. 5 (correct answer)
B. 4
C. 3
D. 2
Unanswered
Q.71)

fixture unit of Urinal (pedestal or similar type)

A. 10 (correct answer)
B. 15
C. 12
D. 9
Unanswered
Q.72) fixture unit of Urinal (flush tank)
A. 2
B. 3 (correct answer)
C. 4
D. 5
Unanswered
Q.73)

fixture unit of Water Closet (flush tank & flushometer-tank),


Hose Bibb or Sill Cock (standard type) private use

A. 2
B. 3 (correct answer)
C. 4
D. 5
Unanswered
Q.74) fixture unit of Water Closet (flush tank & flushometer-tank),
Hose Bibb or Sill Cock (standard type) public use

A. 5 (correct answer)
B. 4
C. 3
D. 2
Unanswered

Q.75)

fixture unit of Water Closet (economical flush) public use

A. 5 (correct answer)
B. 4
C. 3
D. 2
Unanswered
Q.76) fixture unit of Mobile Home (each)-temporary facilities
A. 5
B. 6 (correct answer)
C. 7
D. 8
Unanswered
Q.77)

fixture unit of Bidet, Bathtub(With or Without Shower Over),Laundry Tub or


Clothes Washer (each pair of faucets), Shower (each head), Sink or Dishwasher
private use

A. 2 (correct answer)
B. 3
C. 4
D. 5
Unanswered
Q.78) Fixture unit of bidet, Bathtub(With or Without Shower Over),Laundry Tub or Clothes
Washer (each pair of faucets), Shower (each head), Sink or Dishwasher public use
A. 2
B. 3
C. 4 (correct answer)
D. 5
Unanswered
Q.79)

fixture unit Bar Sink, Drinking Fountain, Lavatory private use

A. 1 (correct answer)
B. 2
C. 1.5
D. 2.5
Unanswered
Q.80) ficture unit Bar Sink, Drinking Fountain, Lavatory public use
A. 1
B. 2 (correct answer)
C. 1.5

D. 2.5
Unanswered
Q.81)

EXCRETA DRAINAGE SYSTEM what piping installations shall be used in high rise

buildings

A. ABS Acrylonitrile-Butadiene-Styrene
B. PVC (POLYVINYL CHLORIDE)
C. Vitrified clay pipe
D. a,b (correct answer)
E. b,c
Unanswered
Q.82) consists of two independently acting internally or externally loaded check valves, four properly
located test cocks with connectors & two isolation gate valves.

A. ATMOSPHERIC VACUUM BREAKER (AVB


B. DOUBLE CHECK VALVE BACKFLOW PREVENTION ASSEMBLY (DC)(correct
answer)

PRESSURE VACUUM BREAKER BACFLOW PREVENTION ASSEMBLY


(PVB)
D. none of the above
Unanswered
C.

consists of two independently acting internally loaded check valves, a differential


pressure relief valve, four properly located test cocks & two isolation gate valves.

Q.83)

PRESSURE VACUUM BREAKER BACFLOW PREVENTION ASSEMBLY


(PVB)
REDUCED PRESSURE PRINCIPLE BACKFLOW PREVENTION
B.
ASSEMBLY (RP)(correct answer)
C. ATMOSPHERIC VACUUM BREAKER (AVB
D. DOUBLE CHECK VALVE BACKFLOW PREVENTION ASSEMBLY (DC)
Unanswered
A.

Q.84) consists of a loaded air inlet valve, an internally loaded check valve, two properly
located test cocks & two isolation gate valves.
A. ATMOSPHERIC VACUUM BREAKER (AVB
B. DOUBLE CHECK VALVE BACKFLOW PREVENTION ASSEMBLY (DC)
PRESSURE VACUUM BREAKER BACFLOW PREVENTION ASSEMBLY
C.
(PVB)(correct answer)
D. none of the above
Unanswered
Q.85)

consist of a body, a checking member & an atmospheric opening.

A. ATMOSPHERIC VACUUM BREAKER (AVB (correct answer)


B. DOUBLE CHECK VALVE BACKFLOW PREVENTION ASSEMBLY (DC)

PRESSURE VACUUM BREAKER BACFLOW PREVENTION ASSEMBLY


(PVB)
D. none of the above
Unanswered
C.

Q.86) All pipings passing under or through walls shall be protected from breakage with embedded
________________.

A. concrete pipe metal sleeves


B. pvc pipe sleeves
C. metal pipe sleeves (correct answer)
D. none of the above
Unanswered
Q.87)

All pipes passing through or under cinders or other corrosive materials shall be protected
from external corrosion by encasing same with _______ or in any other approved manner.

A. metal sheath
B. polybuthane sheath
C. polyethylene sheath (correct answer)
D. plastic sheath
Unanswered
Q.88)

_____________

- shall be supported at every 1m interval.

A. plastic pipe (correct answer)


B. pvc pipe
C. steel pipe
D. lead pipe
Unanswered
Q.89)

in vertical piping ___________shall be supported at intervals not exceeding


1.20m at centers with a rigid vertical back-up

A. PVC pipe
B. Lead Pipe (correct answer)
C. Steel Pipe
D. G.I pipe
Unanswered
Q.90) In PROHIBITED FITTINGS & PRACTICES under this rule, No Drainage
or __________ shall be drilled & tapped for making connections thereto

A. supply piping
B. vent piping (correct answer)
C. drainage piping
D. none of the above
Unanswered

Q.91)

No _____________ shall be located in a room or compartment,


which is not properly lighted & ventilated.

A. CATCH BASIN
B. LAVATORY
C. BIBB
D. WATER CLOSET (correct answer)
Unanswered
Q.92) In GRADE OF HORIZONTAL PIPING If it is impracticable to obtain such slope due to the
following conditions except,

A. Excessive depth of the proposed drainage line


B. Structural and/or geological features of the terrain
C. Existing adverse in arrangements of building structure
D. Reasonable change because of existing weather (correct answer)

You might also like