Professional Documents
Culture Documents
PROXIA
- Consultant technicians
TITLE:
Manual configuration of the BSI ECU on CITROËN C5 (X7).
CONCERNING:
The operations for configuring a BSI ECU:
• Following the replacement of an ECU,
• Following the downloading of an ECU,
• Checking the configuration.
IMPORTANT:
Incorrect configuration will affect the operation of the vehicle. Follow the internet
configuration procedure described in this document and limit the use of manual
configuration just to the cases quoted in the INFO'DIAG.
Page 1 / 31
CONTENTS
1 Introduction………………………………….....………………………………………..3
2 Preliminaries………………………………………...……………………………………3
2.1 Safety advice………………………………………………………………………….3
2.2 Technical advice……….…..………………………………………………………..3
4 Checking of configuration……………………………………………………………..9
4.1 Notes on the configuration tables…………………………………....………..10
4.2 Configuration menus…………………………………………………………….10
4.3 Customer options…………………….…………………………………………..11
4.4 Configuration……………………….……………………………………………..12
4.5 ECUs present………………………………….………………………………….29
4.6 « VIN code » menu………………………………………………………………31
Page 2 / 31
1 INTRODUCTION
Configuration is a sensitive operation, which has direct consequences on the correct
operation of the vehicle. Incorrect configuration can have an impact on:
• Safety (deactivation of vehicle protection devices),
• Overall functioning of the vehicle (complete loss of or damage to vehicle functions)
• Vehicle diagnostics (returning of fault codes which may cause the diagnostic tool
methods to fail, and lead to the unjustified removal of parts).
You are therefore requested to perform the configuration operation following the
instructions on this INFO’DIAG in order to ensure customer satisfaction by returning
their vehicle in a perfect operational state.
2 PRELIMINARIES
The instructions below must be followed to guarantee safety linked to vehicle operation
and well-being.
Page 3 / 31
3 OPERATIONS TO BE CARRIED OUT
This chapter describes the steps to be followed to configure a BSI.
• If the configuration is being carried out following the replacement of a BSI, or
following the downloading of the BSI: follow chapters 3.1, 3.2 and 3.3.
• If the configuration is being carried out independently of a BSI replacement, or the
downloading of a BSI (checking the correct configuration of a vehicle for example):
follow chapters 3.1 and 3.2 only.
Chapter 3.1
Operation to be carried out before removal, downloading or configuration of the BSI:
Printing of customer options configuration values
È
Chapter 3.2
Operations to be carried out to configure the BSI:
È
A) Configuration by internet
È
B) Choice of maintenance plan
È
C) Manual configuration of customer options
È
D) Checking of certain parameters with manual configuration
È
Chapter 3.3
Operations to be carried out after the configuration of the BSI:
Initialisation of BSI (or initialisation of keys or
synchronisation of high frequency remote controls)
Page 4 / 31
3.1 Operations to be carried out before removal, downloading or configuration of
BSI
Before removing the faulty BSI ECU, or downloading or configuring the ECU, establish
communication with this ECU on the vehicle using the LEXIA or PROXIA diagnostic
tool.
Print the screen « Customer Options » from the diagnostic tool, showing the
configuration parameter values (or note these values down manually).
Once this operation has been completed, you may replace or download the BSI, if
required to do so.
Page 5 / 31
3.2 Operations to be carried out to configure the BSI
A) Configuration by internet
LEXIA PROXIA
11 Select the menu « BSI », then validate using key « * ».
12 Select the item « Configuration ».
13 Select the item « Configuration by internet ».
Once the configuration parameters The list of configuration menus appears.
14 screen has appeared, validate Validate using key « F5 » to launch configuration by
using key « * ». internet.
15 Check the accuracy of the vehicle’s VIN, then validate using key « * ».
To allow an internet connection,
make the connections indicated on
Once the tool has received the configuration data, return
16 the diagnostic tool then validate
to the Proxia tool by validating with the « return » key.
using key « * » to start
configuration by internet.
Successively select the menus:
- « CONFIGURATION »,
- « ECUs PRESENT »,
- « VIN code ».
In the « CONFIGURATION » menu, select the sub-
The list of configuration menus:
parameters appears. - « Vehicle definition – Equipment – Driving information »,
17 - « Air conditioning – Cabin heating»,
Validate using the key « * »
- « Lighting – Signalling – Visibility – Rear view mirrors »,
- « Locking – Doors and tailgate – Immobiliser –
Alarm »,
- « Fuel gauge law – Oil level gauge law ».
In each sub-menu and in the ECUs present menu,
validate using the « F5 » key to configure the parameters
returned by the tool.
Return to the main menu of the BSI (« identification », « fault reading », etc.)
18
with successive presses on the « return » key.
NOTE:
If the configuration by internet does not work (presence of a message on the tool
showing the error code linked to the phrase « it is pointless to repeat the operation »),
carry out a manual configuration by replacing the internet configuration (based on the
configuration tables in chapter 0), before continuing with the INFO’DIAG procedure from
section B).
NOTE:
A monitoring of configuration failures is carried out centrally to correct any configuration
malfunctions by internet.
Page 6 / 31
B) Choice of maintenance plan
LEXIA PROXIA
Switch on the ignition. Select the item Select the item « Maintenance – Operational
19 « Maintenance – Operational mode of BSI », mode of BSI »,
then validate with key « * ». then validate with key « * ».
20 Select the item « Maintenance », then validate with key « * ».
21 Select the item « Choice of maintenance plan (new vehicle preparation) ».
Follow the instructions given by the diagnostic tool:
22
reply to the questions asked by the diagnostic tool.
Once the choice of maintenance plan procedure has been carried out, return to the main
23 menu of the BSI (« identification », « fault reading »…) with successive presses on the
« return » key.
Page 7 / 31
3.3 Operations to be carried out after the configuration of the BSI
Operations to be carried out only if replacing or downloading a BSI:
• If the BSI has been replaced: initialise the new BSI ECU on the vehicle (« BSI
initialisation »).
• If the BSI has been downloaded, initialise the BSI ECU (« BSI initialisation »), or the
keys, or simply synchronise the high frequency remote controls, depending on what
is indicated in the procedure accompanying the recall campaign.
To carry out the initialisation operations, ALL of the customer’s keys and the confidential
code card are required.
LEXIA PROXIA
32 Select the item « BSI », then validate using key « * ».
33 Select the item « Initialisation ».
Select the « BSI Initialisation » menu Select the « BSI Initialisation » menu (or
34
(or « Initialisation of keys »). « Initialisation of keys »).
35 Validate using key « * ».
Follow the instructions given by the diagnostic tool screens, in particular those displayed in
36
the band at the bottom of the screen.
Return to the main menu of the BSI (« identification », « fault reading », etc.)
37
with successive presses on the « return » key.
Once steps n° 32 to n° 37 have been completed, carry out the following operations to
check that the vehicle is able to start.
LEXIA PROXIA
38 Select the item « BSI », then validate using key « * ».
39 Select the « Parameter Measures » menu of the BSI.
Select the item « pre-defined parameter
40 Select the sub-menu « Immobiliser ». screens », then select the sub-menu
« Immobiliser ».
41 Check that the parameter « BSI matched to engine ECU » has the value « Yes ».
42 Check that the parameter « Engine ECU locked » has the value « No ».
Check that the parameter « Number of keys initialised » has the value « xx », where « xx »
43
corresponds to the total number of the customer’s vehicle keys.
For each key, check that the parameter « Transponder label recognised » has the value
44
« Yes ».
Return to the main menus screen of the tool (« diagnosis », « downloading», etc.) with
45
successive presses on the « return » key. The diagnostic tool may be disconnected.
Page 8 / 31
4 CHECKING OF THE CONFIGURATION
4.1 Notes on the configuration tables
The display of configuration parameters is conditional on their being present in the BSI
software.
The parameters will be displayed by the diagnostic tool partially or totally depending on
the BSI software version.
Configuration notes:
(1): Means that you have to programme the parameter according to the absence or
presence of the option or to the vehicle definition. If the option or the vehicle definition is
easily identifiable, the instruction is not accompanied by any particular text.
(2): Means that you have to programme the value indicated in the column « Value to be
configured ». This value is valid for all vehicles. It is prohibited to programme any
other value.
(3): Means that this parameter is programmed automatically when you use the
procedure « CHOICE OF MAINTENANCE Plan (PRE-DELIVERY INSPECTION) »
Page 9 / 31
4.2 Configuration menus
After you have selected the menu « Manual configuration », the following menus are
available:
Menus Pages
Customer options 11
Configuration 12
ECUs present 29
VIN code 31
NOTE:
The parameters of the « Customer options » menu are also present in the configuration
menu, it is therefore not necessary to configure these if the configuration of the
parameters of the « Configuration » menu have been or will be carried out.
Page 10 / 31
4.3 Customer Options
Configuration parameter Values to be
Comments
configured
Driver's door control pad with screenprinted
No
Multiplexed folding electric rear button .
view mirrors Driver's door control pad with screenprinted
Yes
button .
Presence of rear screen wiping in Absent
Configure Present if a rear wiper is fitted.
reverse gear Present
Absent With rubber wheel valves.
Type of deflation detection Direct without
With metallic wheel valves.
display of pressures
No daytime-running
lamps
Type of daytime-running lamps (1)
Dedicated daytime-
running lamps
Value not to be configured except on the express
Detection of driver's seat belt not No request of the customer (deactivation of the alert
fastened for detection of driver’s seat belt not fastened).
Yes (2)
For all vehicles with the exception of vehicles
No destined for the Nordic countries (Netherlands,
Lighting by default of daytime- Denmark, Sweden, Finland, Norway and Iceland)
running lamps For all vehicles destined for the Nordic countries
Yes (Netherlands, Denmark, Sweden, Finland,
Norway and Iceland)
For all vehicles with the exception of vehicles
No destined for the Nordic countries (Netherlands,
Simultaneous lighting of daytime- Denmark, Sweden, Finland, Norway and Iceland)
running lamps and sidelamps For all vehicles destined for the Nordic countries
Yes (Netherlands, Denmark, Sweden, Finland,
Norway and Iceland)
Page 11 / 31
4.4 Configuration
Once the « Configuration » menu is selected, the following screen appears.
Page 12 / 31
4.4.1 Menu: vehicle definition – equipment – driving information (menu A)
Configuration Value to be
Comments
parameter (A) configured
All countries other than:
Absent Saudi Arabia, Bahrain, United Arab Emirates,
Overspeed alert for
Kuwait, Oman, Qatar.
the Arabian peninsula
Countries Saudi Arabia, Bahrain, United Arab
Present
Emirates, Kuwait, Oman, Qatar.
Passenger’s seat
position memorisation Absent (2)
control unit option
For engines:
• 1.8 L petrol (6FY),
Absent
• 2.0 L petrol (RFJ),
Key:
Parameter to be systematically checked after configuring by internet
Page 13 / 31
Configuration Value to be
Comments
parameter (A) configured
Origin of the water-
in-diesel-fuel Engine ECU (2)
information
Driving position Absent Driver's seat with manual adjustment.
memorisation option Present Driver's seat with electric adjustment and memory.
Presence of a trailer No
Depending on the presence of a towbar.
relay unit (BSR) Yes
Presence and type of Cruise control and
(2)
vehicle cruise control speed limiter
For engines:
• 1.8 L petrol (6FY),
Engine ECU
• 2.0 L petrol (RFJ),
Key:
Parameter to be systematically checked after configuring by internet
Page 14 / 31
Configuration Value to be
Comments
parameter (A) configured
fuel additive pump Control by wire If particle filter present.
For vehicles except those fitted with a 2.0 L petrol
Standard
(RHR) or 1.8 L petrol (6FY) engine.
Type of alternator
For vehicles fitted with a 2.0 L petrol (RHR) or 1.8 L
Controlled
petrol (6FY) engine.
Presence of No
available parking (1)
space button Yes
Presence of
available parking No (2)
space warning lamp
(3)
Total time before
12 or 24 months 12 months for « severe » use of the vehicle.
next maintenance
24 months for « normal » use of the vehicle.
Configure 0 km for vehicles with an RPO number ≥
0 km 11480 (14th April 2008) or for vehicles which have
Threshold for first had their first service.
service Configure 2500 km for vehicles with an RPO
2500 km number < 11480 and which have not had their first
service.
Maintenance Speedometers in kilometres - CASE N°1
threshold (marketing) (3) For severe use and engines:
15 000 km • 2.0 L petrol (RFJ),
• 1.6 L diesel (9HZ).
(3) For normal use and engines:
• 2.0 L petrol (RFJ),
• 1.6 L diesel (9HZ).
For severe use and engines:
20 000 km • 1.8 L petrol (6FY),
• 3.0 L petrol (XFV),
• 2.0 L diesel (RHR),
• 2.2 L diesel (4HP, 4HT),
• 2.7 L diesel (UHZ).
Key:
Parameter to be systematically checked after configuring by internet
Page 15 / 31
Configuration Value to be
Comments
parameter (A) configured
(3) For normal use and engines:
• 1.8 L petrol (6FY),
• 3.0 L petrol (XFV),
30 000 km
• 2.0 L diesel (RHR),
• 2.2 L diesel (4HP, 4HT),
• 2.7 L diesel (UHZ).
Speedometers in miles - CASE N°2
(3) For severe use and engines:
16 000 km • 2.0 L petrol (RFJ),
• 1.6 L diesel (9HZ).
(3) For normal use and engines:
• 2.0 L petrol (RFJ),
• 1.6 L diesel (9HZ).
For severe use and engines:
20 000 km • 1.8 L petrol (6FY),
• 3.0 L petrol (XFV),
• 2.0 L diesel (RHR),
• 2.2 L diesel (4HP, 4HT),
• 2.7 L diesel (UHZ).
(3) For normal use and engines:
• 1.8 L petrol (6FY),
• 3.0 L petrol (XFV),
32 000 km
• 2.0 L diesel (RHR),
• 2.2 L diesel (4HP, 4HT),
• 2.7 L diesel (UHZ).
Duration before 1st
00 months (2)
service
Kilometre threshold
for forcing of 250 km (2)
customer mode
Memorisation of
Authorised (2) (3)
faults
Presence of an No
electric secondary (1)
brake Yes
Electrically
Absent (2)
adjustable rear seats
Key:
Parameter to be systematically checked after configuring by internet
Page 16 / 31
Configuration Value to be
Comments
parameter (A) configured
With manual adjustment of the height and reach of
Presence of the No
the steering wheel.
welcome function for
the driver With electrical adjustment of the height and reach of
Yes
the steering wheel.
For engines:
• 3.0 L petrol (XFV),
Engine relay unit
• 1.6 L diesel (9HZ),
(BSM)
Origin of the oil • 2.0 L diesel (RHR),
pressure • 2.7 L diesel (UHZ).
information For engines:
• 1.8 L petrol (6FY),
Engine ECU
• 2.0 L petrol (RFJ),
• 2.2 L diesel (4HP, 4HT).
Number of switches
for non-fastening of 5 (2)
seatbelts
Sensor for detection
of presence of a front Absent (2)
passenger
Detection of non-
fastening of the Yes (2)
driver's seatbelt
Detection of non-
fastening of the front Yes (2)
passenger’s seat belt
Presence of a radio No
(1)
RD4 Yes
Presence of a red No Mechanical power steering.
warning lamp for the
Steering Assistance
alert Yes Hydraulic power steering.
Presence of an
orange warning lamp
Yes (2)
for the Steering
Assistance alert
Tolerance on value
set for the cruise 3 km/h (2)
control / speed limiter
Lane Departure Absent (1) Depending on presence of a button for
Warning System
Present deactivation of the function.
option
Key:
Parameter to be systematically checked after configuring by internet
Page 17 / 31
Configuration Value to be
Comments
parameter (A) configured
All diesel engines except:
No
• 2.7 L diesel (UHZ).
Presence of a fuel
On engines:
pump
Yes • Petrol,
• 2.7 L diesel (UHZ).
Presence of a boot
No (2)
relay unit
Saloon
Type of vehicle (1)
Estate
Presence of Head-
No (2)
Up display
Presence of a mobile
No (2)
deflector
Presence of Hands- No
(1)
Free Kit Yes
Presence of CD Absent
(1)
changer Present
Detection of non-
fastening of middle
Yes (2)
rear passenger’s
seat belt
Detection of non-
fastening of rear LH Yes (2)
passenger’s seatbelt
Detection of non-
fastening of rear RH Yes (2)
passenger’s seatbelt
Key:
Parameter to be systematically checked after configuring by internet
Page 19 / 31
Configuration Value to be
Comments
parameter (A) configured
Presence of CD No
(1)
changer Yes
Presence of
No
massaging front (1)
Yes
seats
Mono-zone
For Mono-zone Automatic Air Conditioning.
sunlight sensor
Type of sunlight
sensor
For Bi-zone Automatic Air Conditioning (separate
Bi-zone sunlight
adjustment of the temperature and air distribution on the
sensor
left-hand side and right-hand side).
Key:
Parameter to be systematically checked after configuring by internet
Page 20 / 31
Configuration Value to be
Comments
parameter (B) configured
Programmable For a diesel engine with programmable additional
burner heating.
For engines:
1,19
• 3 L petrol (engine plate XFV).
For engines:
1,24 • 1.8 L petrol (engine plate 6FY),
• 2.0 L petrol (engine plate RFJ).
Aircon compressor
For engines:
drive ratio
• 1.6 L diesel (engine plate 9HZ),
1.28
• 2.0 L diesel (engine plate RHR),
• 2.2 L diesel (engine plate 4HP and 4HT).
For engines:
1.34
• 2.7 L diesel (engine plate UHZ).
Key:
Parameter to be systematically checked after configuring by internet
Page 21 / 31
Configuration Value to be
Comments
parameter (B) configured
For vehicles destined for the following countries,
territories or departments: South Africa, Barbados,
Belgium, Bermuda, Cyprus, Spain, Metropolitan France,
Temperate United Kingdom, Greece, Grenada, Guadeloupe, Guyana,
(-17°C to +37°C) Ireland, Italy, Jamaica, Luxembourg, Malta, Martinique,
Mauritius, New Caledonia, New Zealand, Netherlands,
French Polynesia, Portugal, Reunion, St. Martin, St.
Lucia, Seychelles, Tahiti, Trinidad & Tobago.
For vehicles destined for the following countries:
Albania, Germany, Austria, Azerbaijan, Bosnia, Bulgaria,
Cold Croatia, Denmark, Estonia, Hungary, Iceland, Latvia,
(-25°C to +37°C) Lithuania, Macedonia, Poland, Romania, Serbia-
Montenegro, Slovakia, Slovenia, Switzerland, Czech
Republic.
For vehicles destined for the following countries:
Very cold Armenia, Belarus, Finland, Georgia, Kazakhstan,
(-30°C to +37°C) Kirghizistan, Moldavia, Norway, Uzbekistan, Russia,
Sweden, Turkmenistan, Ukraine.
For vehicles destined for the following countries:
Algeria, Angola, Antigua & Barbuda, Argentina, Aruba,
Type of climate Australia, Bahamas, Bangladesh, Benin, Bolivia,
Botswana, Brazil, Brunei , Burkina Faso, Burundi,
Cambodia, Cameroon, Cape Verde, Sierra Leone, Chile,
Colombia, Comoros, Congo, South Korea, Costa Rica,
Ivory Coast, Cuba, Djibouti, Egypt, El Salvador, Ecuador,
Ethiopia, Fiji, Gabon, Gambia, Ghana , Guatemala,
Guinea, Haiti, Honduras, Hong Kong, India, Indonesia,
Hot Iraq, Iran, Israel, Japan, Jordan, Kenya, Laos, Lebanon,
(-17°C to +45°C) Liberia, Libya, Macao, Madagascar, Malaysia, Malawi,
Mali, Morocco, Mauritania, Mayotte, Mexico ,
Mozambique, Namibia, Nicaragua, Niger, Nigeria,
Uganda, Pakistan, Palestine, Panama, Papua New
Guinea, Paraguay, Peru, Philippines, Central African
Republic, Dominican Republic, Rwanda, Senegal,
Singapore, Somalia, Sudan, Sri Lanka, Surinam, Syria,
Tajikistan, Taiwan, Tanzania, Chad, Thailand, Togo,
Tonga, Tunisia, Turkey, Myanmar, Uruguay, Venezuela,
Vietnam, Yemen, Zambia, Zimbabwe.
For vehicles destined for the following countries:
Very hot
Saudi Arabia, Bahrain, United Arab Emirates, Kuwait,
(-17°C to +50°C)
Oman, Qatar.
Key:
Parameter to be systematically checked after configuring by internet
Page 22 / 31
Configuration Value to be
Comments
parameter (B) configured
Absent
Headlamp wash option (1)
Present
Automatic lighting of
instrument panel and
multifunction screen Absent (2)
depending on external
brightness
Automatic lighting of
hazard warning lamps Absent (2)
in the event of impact
Automatic lighting of
hazard warning lamps
Present (2)
under heavy
deceleration
Presence of front No
(1)
foglamps Yes
Key:
Parameter to be systematically checked after configuring by internet
Page 23 / 31
Configuration Value to be
Comments
parameter (C) configured
Driver's door control pad with screenprinted button
Multiplexed folding No
.
electric rear view
mirrors Driver's door control pad with screenprinted button
Yes
.
Presence of rear
Absent
screen wiping in Configure Present if a rear wiper is fitted.
Present
reverse gear
Lighting of hazard
warning lamps on
Absent (2)
pressing the
emergency call button
Single
filament
halogen
Type of headlamps bulbs (1)
Discharge
bulbs
No daytime-
running
lamps
Type of daytime-
Dedicated (1)
running lamps
daytime-
running
lamps
Presence of a rain and
sunlight sensor with No Configure Present if the vehicle is fitted with a wipers
wipers with regulated Yes stalk with « auto » position.
speed
Presence of a lighting
No (1)
stalk with four
Yes
positions
Presence of a stalk
with one-touch No Configure yes if the vehicle is fitted with a wipers stalk
activation of automatic Yes with « auto » position.
wipe
Key:
Parameter to be systematically checked after configuring by internet
Page 24 / 31
Configuration Value to be
Comments
parameter (C) configured
Activation of automatic
lighting of headlamps (2)
No
via the personalisation
menu
Presence of a third
button on the high No
frequency remote Configure « No » for vehicles fitted with a motorised boot.
control for switching Yes
on the lights
For all vehicles except those destined for the Nordic
No countries (Netherlands, Denmark, Sweden, Finland,
Lighting of daytime- Norway and Iceland)
running lamps by
default For all vehicles destined for the Nordic countries
Yes (Netherlands, Denmark, Sweden, Finland, Norway and
Iceland)
For all vehicles except those destined for the Nordic
No countries (Netherlands, Denmark, Sweden, Finland,
Simultaneous lighting Norway and Iceland)
of daytime-running
lamps and sidelamps For all vehicles destined for the Nordic countries
Yes (Netherlands, Denmark, Sweden, Finland, Norway and
Iceland)
Presence of parking (2)
No
lamps
Presence of headlamp (2) Configure this parameter to « No » even if the vehicle
No
height correctors is fitted with headlamp height correctors
Presence of the light No Configure yes if the vehicle is fitted with « light bars »
pack unit Yes under the fascia.
Static
lighting If the vehicle is fitted with halogen bulbs.
controlled by
the BSI
Type of bend lighting
Dynamic
lighting: If the vehicle is fitted with discharge bulbs.
directional
headlamps
Presence of rear
Absent
screen wiping in Configure Present if a rear wiper is fitted.
Present
reverse gear
Key:
Parameter to be systematically checked after configuring by internet
Page 25 / 31
4.4.4 Menu: locking – doors and tailgate - immobiliser - alarm (menu D)
Configuration Value to be
Comments
parameter (D) configured
Opening of the boot Absent If standard tailgate.
using the high
frequency remote Present If motorised boot tailgate.
control option
With a locking control with Deadlocking (to check
Deadlocking
carry out a Deadlocking actuator test).
Type of locking
With a locking control with normal locking (to check
Normal locking
carry out a Deadlocking actuator test).
No sun roof
Number /
1 sun roof (1)
type of sun roof
blind
Electric
Type of child lock (1)
Mechanical
Passenger door Absent Left-hand drive vehicle.
lock Present Right-hand drive vehicle.
Without ultra-sonic detectors (on the roof console
No alarm
or on the windscreen aperture pillars)
With ultra-sonic detectors (on the roof console or
Standard alarm
Type of alarm on the windscreen aperture pillars)
For vehicles destined for Belgium with ultra-sonic
Alarm for Belgium detectors (on the roof console or on the
windscreen aperture pillars).
Inviolability mode Active (2) (3)
Anti-pinch function
Present on all
on windows and (2)
openers
sun roof
Presence of a
Absent (2)
multiplexed sun roof
Opening of the rear
screen using the
high frequency No (2)
remote control
option
Presence of
electronically Absent (2)
controlled fuel flap
Simultaneous
When actioning unlocking of all of the Vehicle with normal unlocking.
unlocking by high doors
frequency remote
control Unlocking of driver’s
Vehicle with deadlocking.
door only
Key:
Parameter to be systematically checked after configuring by internet
Page 26 / 31
Configuration Value to be
Comments
parameter (D) configured
Type of fitting of
Factory fitted alarm (2)
alarm
No motorised boot
Type of motorised tailgate
(1)
boot tailgate Multiplexed motorised
boot tailgate
Presence of specific
high frequency Absent (2)
receptor (Japan)
Key:
Parameter to be systematically checked after configuring by internet
Page 27 / 31
4.4.5 Menu: fuel gauge law – oil gauge law (menu E)
Configuration Value to be
Comments
parameter (E) configured
Petrol
Type of fuel (1)
Diesel
71 litres For petrol engines.
Tank capacity
72 litres For diesel engines.
Gauge resistance for 330 ohms For petrol engines.
empty tank 332 ohms For diesel engines.
Gauge resistance for full
58 ohms (2)
tank
7 litres For diesel engines.
Fuel gauge law - alert
8 litres For petrol engines.
level
9 litres For petrol and alcohol engines.
Fuel gauge law - Petrol vehicles
(1)
selection of the vehicle Diesel vehicles
Type of engine: XFV
(3.0L petrol)
Type of engine: 9HZ
(1.6L diesel)
Type of engine: RHR
(2.0L diesel)
Oil gauge law – engines Type of engine: 4HP, (1)
4HT (2.2L diesel)
Type of engine: UHZ
(2.7L diesel)
Type of engine: 6FY
(1.8L petrol)
Type of engine: RFJ
(2.0L petrol)
For engines:
• 3.0 L petrol (XFV),
Engine relay unit
• 1.6 L diesel (9HZ),
(BSM)
• 2.0 L diesel (RHR),
Origin of the oil level
information • 2.7 L diesel (UHZ).
For engines:
• 1.8 L petrol (6FY),
Engine ECU
• 2.0 L petrol (RFJ),
• 2.2 L diesel (4HP, 4HT).
Key:
Parameter to be systematically checked after configuring by internet
Page 28 / 31
4.5 ECUs present
Value to be
Calculator Comments
configured
Steering wheel with fixed central
Present (2)
controls
Absent
Rain / sunlight sensor (1)
Present
Absent
Audio amplifier (1)
Present
Absent
Electric parking brake (1)
Present
Key:
Parameter to be systematically checked after configuring by internet
Page 30 / 31
Value to be
Calculator Comments
configured
Absent
Additional heating (1)
Present
Absent
Motorised boot unit (1)
Present
Seat belt not fastened warning
Present (2)
lamp (TNB)
Key:
Parameter to be systematically checked after configuring by internet
Page 31 / 31