Professional Documents
Culture Documents
AUO Model Name: T370XW01 V1 Customer Part No/Project Name: Customer Signature Date AUO
Approved By: Frank Ko Reviewed By: Hong Jye Hong Prepared By: Andrew Liang
Date
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
0/25
Product Specifications 37.0 WXGA Color TFT-LCD Module Model Name: T370XW01 V.1
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
1/25
Contents
No
COVER CONTENTS RECORD OF REVISIONS 1 2 3 GENERAL DESCRIPTION ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS
ITEM
ELECTRICAL CHARACTREISTICS INTERFACE CONNECTIONS INPUT TIMING SPECIFICATIONS SIGNAL TIMING WAVEFORMS COLOR INPUT DATA REFERNECE POWER SEQUENCE OPTICAL SFECIFICATIONS MECHANICAL CHARACTERISTICS RELIABLITY INTERNATIONAL STANDARDS SAFETY EMC Packing PRECAUTIONS
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
2/25
Record of Revision
Version 0.0 0.1 0.2 Date Sep. 30,05 Oct. 04, 05 Oct. 30, 05 No First Draft Update P.9 3-3 Input Timing Specifications Update P.9 3-3 Input Timing Specifications Update P22,23 Packing Spec Description Remark
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
3/25
1. General Description
This specification applies to the 37.0 inch Color TFT-LCD Module T370XW01. This LCD module has a TFT active matrix type liquid crystal panel 1366x768 pixels, and diagonal size of 37.0 inch. This module supports 1366x768 XGA-Wide mode (Non-interlace). Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot. The T370XW01 has been designed to apply the 8-bit 1 channel LVDS interface method. It is intended to support displays where high brightness, wide viewing angle, high color saturation, and high color depth are very important.
* General Information
Items
Active Screen Size Display Area Outline Dimension Driver Element Display Colors Number of Pixels Pixel Arrangement Pixel pitch Surface Treatment
Specification
37.02 819.6 (H) x 460.8(V) 877.0(H) x 514.6(V) x 54.7(D) a-Si TFT active matrix 16.7M 1366x768 RGB vertical stripe 0.6(H) x 0.6(W) Hard-Coating (3H), Anti-Glare
Unit
Inches mm mm
Note
With inverter
Colors Pixel
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
4/25
Note 1 : Duration = 50msec Note 2 : Maximum Wet-Bulb should be 39 and No condensation. The relative humidity must not exceed 90% non-condensing at temperatures of 40 or less. At temperatures greater than 40, the wet bulb temperature must not exceed 39.
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
5/25
3. Electrical Specification
3-1 Electrical Characteristics
The T370XW01 requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input which powers the CCFL, is typically generated by an inverter. Value Min. LCD Power Supply Input Voltage Power Supply Input Current Power Consumption Inrush Current Backlight Power Consumption Lamp Life Time Note : 1. VLCD ILCD PLCD IRUSH 10.8 60,000 12.0 0.55 6.6 135 13.2 0.66 7.92 3 155 V. A. W A W hr 3 1 1 2 Typ. Max. Unit Note
Parameter
Symbol
3.
4.
Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to conducting tape, TFT-LCD Module have a low luminance and the inverter has abnormal action because leakage current occurs between lamp wire and conducting tape.
5.
The relative humidity must not exceed 80% non-condensing at temperatures of 40 or less. At temperatures greater than 40, the wet bulb temperature must not exceed 39. When operate at low temperatures, the brightness of CCFL will drop and the life time of CCFL will be reduced.
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
6/25
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
7/25
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
8/25
No
Item
Symbol VBL IBL PBL FLO FBLD On Off BLON BLON Vdim Vdim
Test Condition
Min 21.6
Unit V A W kHz Hz V V V V % %
Note
1 Power Input Voltage 2 Power Input Current 3 Power Consumption 5 Lamp Oscillating Frequency 6 Dimming Frequency 7 On/Off Coltrol Voltage
40 150 2 0 -
*2
8 DC Dimming Control *
Max Min
6
*1
Duty Ratio
Ta=252 1: Connection of brightness control terminal Bright control by the voltage 0V : Min. brightness 3.3V : Max. brightness 2: BLON Logic H(5V) : Back Light ON L (0V) : Back Light OFF OPEN : Back Light OFF
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
9/25
3.
Input specification CN2 : S10B-PH-SM3-TB(JST) Feature +24V +24V +24V +24V +24V GND GND GND GND GND Brightness control signal input (0V: min ~ 3.3V:Max) 5V : On, 0V : Off External PWM Dimming Control
1
CN1 : S14B-PH-SM3-TB(JST) No Signal Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 VBL VBL VBL VBL VBL GND GND GND GND GND VDIM VBLON E-PWM PWM SEL*
No Signal Name 1 2 3 4 5 6 7 8 9 10 VBL VBL VBL VBL VBL GND GND GND GND GND
Feature +24V +24V +24V +24V +24V GND GND GND GND GND
Setting
VDIM (pin 11) E-PWM (pin13)
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
10/25
Vertical Frequency Horizontal Frequency 50Hz Driving Timing Signal Vertical Section Item Period Active Blanking Horizontal Section Clock Period Active Blanking Frequency
Min. 940
Max. 980
Unit Th Th
172 1414
212 1560
Th Tclk Tclk
48 65.13 49 47.00
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
11/25
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
12/25
COLOR
DATA REFERENCE
Input Color Data
Color MSB
BLUE LSB
R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0 Black Red(255) Green(255) Basic Color Blue(255) Cyan Magenta Yellow White RED(000) RED(001) RED ---RED(254) RED(255) 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 0 0 1 0 0 0 1 1 1 0 1 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 1 0 1 0 1 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 1 0 1 0 0
GREEN(000) 0 GREEN(001) 0 GREEN ---GREEN(254) 0 GREEN(255) 0 BLUE(000) BLUE(001) BLUE ------BLUE(254) BLUE(255) 0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
1 1 0 0
0 1 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 0
0 0 0 1
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
0 0
1 1
1 1
1 1
1 1
1 1
1 1
1 1
0 1
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
13/25
90%
90%
10%
10%
t1
t2
t5
t6
t7
t3
t4
Lamp ON Backlight
Values Parameter t1 t2 t3 t4 t5 t6 t7 1000 Min. 0.5 20 700 10 1 Typ. Max. 1000 50 50 300 -
Units ms ms ms ms ms ms ms
Copyright AU Optronics, Inc. January, 2003 All Rights Reserved. No Reproduction and Redistribution Allowed
14/25
24V(typ.)
90%
VDDB
T1
T2
T5
condition
T6
for
Inverter
Units
ms ms ms ms ms ms
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
15/25
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
16/25
4. Optical Specification
Optical characteristics are determined after the unit has been ON and stable for approximately 30 minutes in a dark environment at 25. The values specified are at an approximate distance 50cm from the LCD surface at a viewing angle of and equal to 0. Fig.1 1 presents additional information concerning the measurement equipment and method.
Parameter
Contrast Ratio Surface Luminance, white Dark Luminance Luminance Variation Response Time Rise Time
Decay Time
Symbol
Min. CR LWH LBK WHITE TrR TrD T RX RY 9p 800 400
Values
Typ. 1000 500 Max. 1.3 15 5 8 0.640 0.330 0.290 Typ 0.03 0.600 0.150 0.060 0.280 0.290 Typ +0.03 1.3 18 7 35
Units
Notes
1 Cd/ Cd/m2 3 ms ms ms 5 4 2
GX GY
BLUE
BX BY
WHITE
WX WY
Viewing Angle x axis, right(=0) x axis, left(=180) y axis, up(=90) y axis, down (=0) r l u d 88 88 88 88 Degree 6
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
17/25
Note: 1. Contrast Ratio (CR) is defined mathematically as: Surface Luminance with all white pixels Contrast Ratio= Surface Luminance with all black pixels
2.
Surface luminance is luminance value at point 1 across the LCD surface 50cm from the surface with all pixels displaying white. From more information see FIG 2.
3.
FIG. 2 Luminance
H/2
V/2
H/2
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
H/6
V/6
18/25
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
Photodetector Output
L0,15,L31,.L255
Time
TrR
19/25
7. Mechanical Characteristics
The contents provide general mechanical characteristics for the model T460HW01. In addition the figures in the next page are detailed mechanical drawing of the LCD. Horizontal Outline Dimension Vertical Depth Bezel Opening Area Horizontal Vertical Display Active Area Horizontal Vertical Weight Surface Treatment 10300g (Typ.) Hard-Coating (3H), Anti-Glare, 877.0 mm 514.6 mm 54.7 mm(with inverter) 827.8 mm 469.4 mm 819.6 mm 460.8 mm
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
20/25
2-D Drawing
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
21/25
6. Reliability
Environment test condition No 1 2 3 4 5 Test Item High temperature storage test Low temperature storage test High temperature operation test Low temperature operation test Vibration test (non-operating) Ta=60 Ta= -20 Ta=50 Ta=0 50%RH Condition 240h 240h 240h 240h
Wave form: random Vibration level: 1.5G RMS Bandwidth: 10-500Hz, Duration: X, Y, Z 20min One time each direction Shock level: 50G Waveform: half since wave, 11ms Direction: X, Y, Z One time each direction Wave form: random Vibration level: 1.5G RMS Bandwidth: 10-500Hz, Duration: X, Y, Z 30min One time each direction Height: 53.3cm 1 corner, 3 edges, 6 surfaces (ASTMD4169-I)
Result Evaluation Criteria There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition.
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
22/25
7. International Standard
7-1. Safety
(1) UL1950 Third Edition, Underwriters Laboratories, Inc. Jan. 28, 1995 Standard for Safety of Information Technology Equipment Including electrical Business Equipment. (2) CAN/CSA C22.2 No. 950-95/60950 Third Edition, Canadian Standards Association, Standard for Safety of Information Technology Equipment Including Electrical Business Equipment. (3) EN60950 : 1992+A2: 1993+A2: 1993+C3: 1995+A4: 1997+A11: 1997 IEC 950: 1991+A1: 1992+A2: 1993+C3: 1995+A4:1996 European Committee for Electrotechnical Standardization (CENELEC) EUROPEAN STANDARD for Safety of Information Technology Equipment Including Electrical Business Equipment.
7-2. EMC
a) ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical Equipment in the Range of 9kHz to 40GHz. American National standards Institute (ANSI), 1992 b) C.I.S.P.R Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. International Special committee on Radio Interference. c) EN 55022 Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment. European Committee for Electrotechnical Standardization. (CENELEC), 1998 7-3. Lead Free product
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
23/25
8. Packing
Label : 83mm * 23mm
Carton Size
965(L)mm*280(W)mm*662(H)mm
Pallet Size
1130(L)mm*980(W)mm*123(H)mm
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
24/25
Module
3pcs Modules
Cushion set
Cushion down
H Tape
3pcs / 1 carton
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
25/25
By Air : 1 pallet + 4 box 2 layers ( 8*3=24 pcs module) By Sea : 1 pallet + 4 box 3 layers (12*3=36 pcs module)
Moisture-proof film
Label
PET band
Corner angle
Pallet
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCD module.
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage: V=200mV(Over and under shoot voltage) (2) Response time depends on the temperature. (In lower temperature, it becomes longer..) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time (required time that brightness is stable after turned on) becomes longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimize the interface.
9-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5 and 35 at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.
Copyright AU Optronics, Inc. Jun, 2005 All Rights Reserved. No Reproduction and Redistribution Allowed
27/25