Professional Documents
Culture Documents
\
|
=
|
|
.
|
\
|
=
= =
q
q
where r
P
is called the pressure ration and k = c
p
/c
v
is the specific heat ratio.
MaximumPressureRatio
Given that the maximum and minimum temperature can be prescribed for the Brayton
cycle, a change in the pressure ratio can result in a change in the work output from the
cycle.
s
T
1
2
3
4
Q
H
Q
L
P=Const.
P =Const.
1
2
3
4
v
P
Isentropic
Isentropic
Q
L
Q
H
M. Bahrami ENSC 461 (S 11) Brayton Cycle 3
The maximum temperature in the cycle T
3
is limited by metallurgical conditions because
the turbine blades cannot sustain temperatures above 1300 K. Higher temperatures (up to
1600 K can be obtained with ceramic turbine blades). The minimum temperature is set by
the air temperature at the inlet to the engine.
Fig. 3: An optimum pressure ratio exists for a given max., min. temperature ratio that
maximized the net work output.
ActualBraytonCycle
Irreversibilities exist in actual cycle. Most important differences are deviations of actual
compressor and turbine from idealized isentropic compression/expansion, and pressure
drop in combustion chamber.
M. Bahrami ENSC 461 (S 11) Brayton Cycle 4
Fig. 4: Actual Brayton cycle.
s
a
s
a
T
a
s
a
s
c
h h
h h
w
w
h h
h h
w
w
4 3
4 3
1 2
1 2
~ =
~ = q q
TheBraytonCyclewithRegeneration
The high pressure air leaving the compressor can be heated by transferring heat from
exhaust gases in a counter-flow heat exchanger which is called a regenerator.
Fig. 5: Schematic for a Brayton cycle with regenerator.
Compressor
Turbine
Shaft
Air
Combustion
chamber
Combustion
products
W
net
1
2 3
5
4
Q
T
1 s
2s
2a
3
4s
4a
Pressure drop
Pressure drop
6
Regenerator
M. Bahrami ENSC 461 (S 11) Brayton Cycle 5
Fig. 6: T-s diagram for a Brayton cycle with regeneration.
In the ideal case, the air exits the regenerator at the inlet temperature of the exhaust gases,
T
4
. One can write:
q
regen, actual
= h
5
h
2
q
regen, max
= h
5
h
2
= h
4
h
2
The effectiveness of regenerator is defined as:
( ) conditions standard - air - cold assuming
2 4
2 5
2 4
2 5
max ,
,
T T
T T
h h
h h
q
q
regen
act regen
= = c
Thermal efficiency of an ideal Brayton cycle with regenerator can be found from:
( )
( ) k k
p regen th
r
T
T
/ 1
3
1
,
1
|
|
.
|
\
|
= q
TheBraytonCyclewithIntercooling,Reheating,andRegeneration
The net work output of the cycle can be increased by reducing the work input to the
compressor and/or by increasing the work output from turbine (or both).
Using multi-stage compression with intercooling reduces the work input the compressor.
As the number of stages is increased, the compression process becomes nearly isothermal
at the compressor inlet temperature, and the compression work decreases.
Likewise utilizing multistage expansion with reheat (in a multi-turbine arrangement) will
increase the work produced by turbines.
s
T
1
2
3
4
Q
H
Q
L
Regeneration
5
5
6
Q
regen
Q
regen
M. Bahrami ENSC 461 (S 11) Brayton Cycle 6
Fig. 7: A gas-turbine engine with two-stage compression with intercooling, two-stage
expansion with reheating, and regeneration.
When intercooling and reheating are used, regeneration becomes more attractive since a
greater potential for regeneration exists.
The back work ratio of a gas-turbine improves as a result of intercooling and reheating.
However; intercooling and reheating decreases thermal efficiency unless they are
accompanied with regeneration.
Fig. 8: T-s diagram for an ideal gas-turbine cycle with intercooling, reheating, and
regeneration.
Intercooler
Combustion
chamber
Reheater
Q
Intercooler
Compressor 2
1
Regenerator
Q
Reheater
Turbine 1 Turbine 2
Q
H
Compressor 1
2 3
4
5
6
7 8
9
10
W
net
T
s
1
2
3
4
5
6
7
8
9
10
Q
in
Q
in
Q
out
Q
out
Q
regen.
M. Bahrami ENSC 461 (S 11) Brayton Cycle 7
As shown in Fig. 8:
T
1
=T
3
, T
2
=T
4
In an ideal regenerator, T
5
=T
9.
In practice (actual regenerator), T
5
<T
9
.
T
8
=T
6
, T
7
=T
9
The net work input to a two-stage compressor is minimized when equal pressure ratios
are maintained across each stage. That is:
3
4
1
2
P
P
P
P
=
This procedure also maximizes the turbine work output.
9
8
7
6
P
P
P
P
=