Professional Documents
Culture Documents
Suitability
Suitable for: Concrete so B15, natural stone with dense structure. For fixing of: Metal constructions, metal profiles, sole plates, brackets, railings, windows, gratings, machines, timber constructions (large washer), beams, purlins, supports etc.
1 2 3 4
fischer Bolt FBN, zinc plated and passivated steel fischer Bolt FBN with large washer, zinc plated and passivated steel fischer Bolt FBN, A4 stainless steel* fischer Bolt FBN fvz (hot dipped galvanized)*
* not included in approval notice.
Description
The fischer FBN bolt is a more advanced development of the FB and now offers even more scope for application. In concrete terms, this means that the FBN can be installed with a variable embedment depth, i.e. the user has the choice between the standard embedment depth with maximum permitted load and an extended useful length with a reduced permitted load. The thread has been extended with this in mind.
2
Installation instructions
Before tapping in, place the nut in the best position for installation (bolt projects approx. 23 mm). The letter engraved on the head of the anchor is required for approval reasons and identifies the FBN in its installed state.
Advantages
Through its variable useful length (see description) and the extended thread, the FBN offers increased scope for use. The expansion clip has been improved, resulting in increased load values, even in low-quality concrete. Anchoring with the FBN is now even more economical. The FBN can be anchored with only a few turns. A special assortment with a large washer to DIN 440 is available for use with wood.
Approvals
F 90
Installation diagram
32
Type
Drill mm
Overalllength mm
Thread x length
Type
Drill mm
Overall length mm
Thread x length
FBN 6x40* FBN 6x55* FBN 6x70 FBN 6x75* FBN 6x90 FBN 8x60 FBN 8x75 FBN 8x95 FBN 8x115 FBN 8x165 FBN 10x70 FBN 10x90 FBN 10x110 FBN 10x125 FBN 10x175 FBN 10x215 FBN 10x235 FBN 12x85 FBN 12x115 FBN 12x130 FBN 12x145 FBN 12x200 FBN 16x110 FBN 16x145 FBN 16x170 FBN 16x220 FBN 20x120* FBN 20x165 FBN 20x205 FBN 20x265 FBN 20x395
B F K P C G K P S T C F I P E K P
45130 45136 45137 45131 45138 45139 45140 45141 45132 45142 15399 45143 45144 45145 45146 45133 45147 45148 45149 45150 45134 45151 45152 45153 45135 45154 45155 45156 45157
69087 69088 69089 69090 69091 69092 69093 69094 69095 69096 69097 69098 69099 69100
6 6 6 6 6 8 8 8 8 8 10 10 10 10 10 10 10 12 12 12 12 12 16 16 16 16 20 20 20 20 20
45 50 65 70 85 55 73 93 113 163 65 83 103 118 168 208 228 75 105 120 135 190 98 133 158 208 111 151 191 251 381
20 25 40 25 40 35 48/35 48/35 48/35 48/35 42 50/42 50/42 50/42 50/42 50/42 50/42 50 70/50 70/50 70/50 70/50 64 84/64 84/64 84/64 70 100 100 100 100
40 55 70 75 90 60 75 95 115 165 70 90 110 125 175 215 235 85 115 130 145 200 110 145 170 220 120 165 205 265 395
5 10 10 30 30 5 10/23 30/43 50/63 100/113 5 15/23 35/43 50/58 100/108 140/148 160/168 5 15/35 30/50 45/65 100/120 10 25/45 50/70 100/120 10 20 60 120 250
M 6 x 16 M 6 x 30 M 6 x 25 M 6 x 30 M 6 x 30 M 8 x 23 M 8 x 41 M 8 x 61 M 8 x 81 M 8 x 130 M10 x 31 M10 x 51 M10 x 71 M10 x 87 M10 x 134 M10 x 174 M10 x 194 M12 x 41 M12 x 71 M12 x 86 M12 x 103 M12 x 157 M16 x 54 M16 x 89 M16 x 114 M16 x 166 M 20 x 50 M 20 x 50 M 20 x 90 M 20 x 90 M 20 x 90
FBN 8x60 HDG* FBN 8x75 HDG* FBN 8x115 HDG* FBN 8x165 HDG* FBN 10x70 HDG* FBN 10x90 HDG* FBN 10x125 HDG* FBN 10x175 HDG* FBN 10x215 HDG* FBN 12x85 HGD* FBN 12x115 HDG* FBN 12x130 HDG* FBN 12x145 HDG* FBN 12x200 HDG* FBN 16x110 HDG* FBN 16x145 HDG* FBN 16x170 HDG* FBN 16x220 HDG*
57525 57526 57527 57528 57529 57530 57531 57532 57533 57534 57535 57536 57537 57538 57539 57540 57541 57542
8 8 8 8 10 10 10 10 10 12 12 12 12 12 16 16 16 16
55 73 113 163 65 83 118 168 208 75 105 120 135 190 98 133 158 208
35 48 48 48 42 50 50 50 50 50 70 70 70 70 64 84 84 84
60 75 115 165 70 90 125 175 215 85 115 130 145 200 110 145 170 220
M 8 x 23 M 8 x 41 M 8 x 81 M 8 x 130 M10 x 31 M10 x 51 M10 x 87 M10 x 134 M10 x 174 M12 x 41 M12 x 71 M12 x 86 M12 x 103 M12 x 157 M16 x 54 M16 x 89 M16 x 114 M16 x 166
100 50 50 25 50 50 20 20 20 20 20 20 20 20 10 10 10 10
Mean ultimate loads and recommended loads for single anchors of fischer bolt FBN with large axial spacing and edge distance
Non-cracked concrete Anchor size M6 M8 M10 50 68 10 22.4 20.9 30.5 16.6* 19.1* 24.0* 5.8 5.8 5.8 7.5 7.5 7.5 50 70 12 25.6 30.5 27.6 31.6* 7.5 7.5 7.5 7.5 M12 70 90 12 35.0 35.2* 39.9* 27.6* 27.6* 31.6* 64 88 16 35.0 38.2 33.4* 56.5* M16 84 108 16 M20 100 131 20 Effective anchorage depth heff [mm] 40 35 48 42 Drill hole depth h1 [mm] 55 50 63 60 Drill hole diameter do [mm] 6 8 8 10 Mean ultimate loads Nu,m and Vu,m [kN] Tensile 0 Nu,m [kN] gvz 14.3* 19.2 [kN] fvz 15.5* [kN] A4 10.6* 16.4 20.5 Shear 90 Vu,m [kN] gvz 11.3* 16.6* [kN] fvz 12.3* [kN] A4 9.0* 15.1* 24.0* Recommended loads Nrec and Vrec [kN] Tensile 0 Nrec [kN] gvz 2.5 4.4 4.7 [kN] fvz 4.8 [kN] A4 3.3 4.4 4.7 Shear 90 Vrec [kN] gvz 3.2 5.3 5.8 [kN] fvz 6.7 [kN] A4 4.3 5.3 5.8 Recommended bending moment Mrec [Nm] Mrec [Nm] gvz 10.5 10.5 21.4 [Nm] fvz 13.7 [Nm] A4 6.5 14.7 14.7 29.7 Component dimensions, minimum axial spacings and edge distances Min. axial spacing1) smin [mm] gvz 35 50 45 fvz 50 A4 40 50 50 Min. edge distance1) cmin [mm] gvz 35 50 55 fvz 50 A4 35 35 60 Min. structural component 100 100 100 100 hmin [mm] thickness 7.5 15 15 30 Required torque Tinst [Nm]
FBN with large washer according to DIN 440, outside diameter approx. 3.5 x d
do Imprint on head Art. No. td Min. drill-hole depth for through fixing mm hef Min. Anchorage depth mm l tfix Max. fixing thickness mm M
10.9 10.9 15.2 20.9 10.0 11.6 10.9 9.2 13.4 12.9 16.9 16.9 36.5 12.9 16.9 12.9 16.9 16.9
Type
Drill mm
Overall length mm
Thread x length
FBN 12x180 GS FBN 12x200 GS FBN 12x220 GS FBN 12x240 GS FBN 12x260 GS FBN 12x300 GS FBN 12x350 GS FBN 16x220 GS FBN 16x260 GS FBN 16x280 GS FBN 16x320 GS FBN 16x370 GS FBN 16x420 GS
1)
N P R S T V W P S T V W X
45160 45161 45162 45163 45164 45165 45166 45167 45168 45169 45170 45171 45172
12 12 12 12 12 12 12 16 16 16 16 16 16
170 190 210 230 250 290 340 208 248 268 308 358 408
70/50 70/50 70/50 70/50 70/50 70/50 70/50 84/64 84/64 84/64 84/64 84/64 84/64
180 200 220 240 260 300 350 220 260 280 320 370 420
80/100 100/120 120/140 140/160 160/180 200/220 250/270 100/120 140/160 160/180 200/220 250/270 300/320
M12 x 137 M12 x 157 M12 x 177 M12 x 100 M12 x 100 M12 x 100 M12 x 100 M16 x 166 M16 x 100 M16 x 100 M16 x 100 M16 x 100 M16 x 100
20 20 20 10 10 10 10 10 10 10 10 10 10
21.4 40.5 40.5 96.0 96.0 194.6 29.1 40.5 96.0 29.7 46.9 46.9 114.3 114.3 55 55 60 65 65 55 100 30 100 65 100 70 100 50 75 130 80 90 100 75 140 50 140 90 100 80 130 100 90 85 90 105 80 80 170 100 170 150 200 200
* steel failure 1) For min. axial spacing and min. edge distance the above described loads have to be reduced! (See Technical Handbook or design software CC-Compufix) All load values apply for: concrete compressive strength fc,200 = 30 N/mm2 no edge or spacing influences. Recommended loads: material safety factors M and safety factor for load L = 1.4 are included. Material safety factor M depends on type of anchor. The conditions of application differ from those given in the European Technical Approval. For further detailed information about European Technical Approvals please contact fischer technical service department.
2)
Min. embedment depth for maximum permitted load/the minimum embedment depth can be reduced to . . . for the extended effective length and reduced load. Embedment length for maximum permissible load/embedment length for reduced load.
33
Suitability
Suitable for: concrete B15 and dense natural stone.
fischerbolt FA
For fixing: Railings, hand rails, seating, stock pens, gratings, supports, consoles, machines, metal constructions, metal profiles.
Description
For through fixing. Torque controlled, safe expansion. Highest reliability. Demountable fixing leaving a flush surface Domed nut for neat appearance Red knurled collar prevents turning in hole on installation The expansion sleeve guarantees an even, calibrated hold and depth in all compact materials The reduced diameter and practical installation make it ideal for a quick, secure job
Type pack
Art. No.
Drill mm
Fixing length mm
Torque Nm
Qty per
( 8 x 70) ( 8 x 85) (10 x 85) (10 x 120) (12 x 100) (12 x 135) (14 x 115) (14 x 145)
8 8 10 10 12 12 14 14
50 50 60 60 70 70 80 80
15 25 15 50 15 50 20 50
10 10 20 20 35 35 50 50
13 13 17 17 19 19 22 22
25 25 25 25 20 20 10 20 Ultimate loads Fu, m [kN] (mean values) and recommended loads Frec [kN] for a single anchor in non-cracked concrete
Anchor type/thread Fu, m Frec Axial spacing Edge distance Min. component thickness B25 B25 (cm) (cm) (cm) FA 8 1280 250 16 8 15 FA 10 1540 350 24 10 15 FA 12 2030 450 26 13 20 FA 14 2540 600 40 15 20
Installation diagram
34
35
NEW
4 5 6
Suitability
Suitable for: Concrete B15 and masonry building materials. For fixing of: Installation rails, ventilation ducts, pipework, suspended ceilings, metal profiles, wood sub-structures, facade sub-structures, shelf feet. Also suitable for temporary fastenings such as wall shuttering.
1 2 3
Panhead (P) Countersunk head (SK) Hexagon with integrated washer (US)
Description
fischer concrete screws have a specially hardened thread. The lower turns of the thread also have teeth. The diameter of the hole and the thread of the screw are adapted to one another so that the special thread of the screw cuts into the concrete. The thread turns creating a fine undercut, thereby ensuring that the load is safely supported by a perfect form fit. The teeth allow the thread to cut into the concrete, thereby reducing the amount of energy required to insert the screw into its position.
Advantages
Fast installation by simply screwing the screw into the hole in the concrete. Fully detachable screw attachment. High permissible loads through safe form fit. Minimum edge and axial distances through absence of expansion pressure. Variable application through different head shapes.
Approvals
Z-21.1-1717 Z-21.1-1716 Z-21.1-1718
F 90/120
Installation diagram
36
Installation example
Type
Art. No.
Drill mm
Screw outer mm
Screw length mm
Drive
zinc plated FBS 5/5 P FBS 6/5 SK FBS 6/5 P FBS 6/25 P FBS 6 M8 FBS 8/5 US FBS 8/25 US FBS 8/15 S FBS 10/5 S FBS 10/15 S FBS 10/25 S 66774 66935 66939 66948 66949 66956 66957 66958 67062 67063 67168 5 6 6 6 6 6 8 8 8 10 10 10 10 7 8 8 8 12 12 12 14 14 14 14 6.5 7.6 7.6 7.6 7.6 7.6 10.5 10.5 10.5 12.5 12.5 12.5 12.5 65 65 65 85 60 60 90 110 100 100 110 120 105 55 55 55 55 55 55 75 75 75 85 85 85 85 5 5 5 25 5 25 15 5 15 25 10 60 60 60 80 55 55 80 100 90 90 100 110 95 T30 T30 T30 T30 SW10 SW13 100 100 100 100 100 100
T40/SW13 100 T40/SW13 100 SW16 SW18 SW18 SW18 SW17 100 50 50 50 50
Mean ultimate loads and recommended loads for single anchors of fischer concrete screw FBS with large axial spacing and edge distance
Non-cracked concrete Anchor size Effective anchorage depth Drill hole depth Screw-in depth Drill hole diameter Mean ultimate loads Nu,m and Vu,m [kN] Tensile Shear Recommended loads Nrec and Vrec [kN] Tensile Shear Recommended bending moment Mrec [Nm] Mrec Component dimensions, minimum axial spacings and edge distances Min. axial spacing1) Min. edge distance1) Min. structural component thickness smin cmin hmin [mm] [mm] [mm] 50 60 120 60 65 130 50 100 110 50 100 110 50 60 120 60 65 130 [Nm] [Nm] gvz A4 19.0 40.0 36.8 8.0 19.0 40.0 36.8 0 90 Nrec Vrec [kN] [kN] [kN] [kN] gvz A4 gvz A4 5.3 7.4 6.6 6.6 12.1 13.6 0.3 0.8 2.5 7.4 4.0 4.0 12.1 13.3 0 90 Nu,m Vu,m [kN] [kN] [kN] [kN] gvz A4 gvz A4 21.2 29.6 26.4 26.4 48.4 54.4 1.2 3.2 10.0 29.6 16.0 16.0 48.4 54.4 heff ho hnom do [mm] [mm] [mm] [mm] FBS 8 50 85 75 8 FBS 10 60 95 85 10 FBS 5* 55 60 5 Cracked concrete FBS 6* 55 60 6 FBS 8 50 85 75 8 FBS 10 60 95 85 10
* For the fixing of lightweight suspended ceiling constructions only. 1) For min. axial spacing and min. edge distance the above described loads have to be reduced! (See Technical Handbook or design software CC-Compufix) All load values apply for: concrete compressive strength fc,200 = 30 N/mm2 no edge or spacing influences. Recommended loads: material safety factors M and safety factor for load L = 1.4 are included. Material safety factor M depends on type of anchor. The conditions of application differ from those given in the German approval. For further detailed information about German approval please contact fischer technical service department.
37
Suitability
Suitable for: Concrete B15 and natural stone with dense structure. For fixing of: Railings, handrails, gratings, supports, consoles, machines, metal constructions, metal profiles etc.
1 2
Description
The fischer Sleeve anchor FSA is a torque controlled expanding steel anchor for all through fixings for light and medium loads. Unlike ordinary sleeve anchors, the geometry of the expansion sleeve and the cone has been improved and the combined effect of these two functional elements optimised. This guarantees full expansion in all cases, thus providing optimum safety and reliability at the high level you expect of fischer. The FSA is available in 2 versions: FSA-S with hexagon screw and cone nut
2
Picture for illustration purposes only
Advantages
The simple design and construction result in an excellent cost-performance ratio. The computer optimised anchor cone and the suitably adjusted expansion sleeve result in a safe expansion. The crescent-shaped punch-outs enable the sleeve to neatly slide together on the axis when bridging hollow layers. The assembly object braces tightly against the building material. The setting depth mark allows verification of the correct installation any time. The setting head at the runout of the conical bolt prevent damage to the thread. In the case of de-mounting, an easy thread travel is always ensured.
l do td hv da
MD M
Installation diagram
38
FSA-S zinc-plated and passivated steel, with hexagon screw and cone nut
do td Min. drill-hole depth for through fixing mm hv Min. anchorage depth mm l da Max. fixing thickness mm M SW
FSA zinc-plated and passivated steel, with conical bolt and hexagon nut
do td Min. drill-hole depth for through fixing mm hv Min. anchorage depth mm l da Max. fixing thickness mm M SW
Type
Art. No.
Drill mm
Fixing length mm
Thread
Type
Art. No.
Drill mm
Fixing length mm
Thread
FSA 8/15 S FSA 8/40 S FSA 8/65 S FSA 10/10 S FSA 10/35 S FSA 10/60 S FSA 12/10 S FSA 12/25 S FSA 12/50 S
8 8 8 10 10 10 12 12 12
35 35 35 40 40 40 50 50 50
15 40 65 10 35 60 10 25 50
10 10 10 13 13 13 17 17 17
50 50 50 20 20 20 20 20 20
FSA 6/5 FSA 6/8 FSA 6/25 FSA 8/8 FSA 8/30 FSA 8/55 FSA 10/10 FSA 10/35 FSA 10/60 FSA 12/12 FSA 12/20 FSA 12/50 FSA 12/75 FSA 16/12
60168 60156 60157 60158 60150 60159 60160 60151 60152 60161 60153 60154 60162 60163 60155 60164 60165 60166 60167
6 6 6 8 8 8 10 10 10 12 12 12 12 16 16 16 20 20 20
20 30 33 34 36 37 38 40 40 46 50 50 50 52 58 62 62 64 63
5 8 25 8 30 55 10 35 60 12 20 50 75 12 50 80 20 50 95
M 4.5 M 4.5 M 4.5 M 6 M 6 M 6 M 8 M 8 M 8 M10 M10 M10 M10 M12 M12 M12 M16 M16 M16
8 8 8 10 10 10 13 13 13 17 17 17 17 19 19 19 24 24 24
FSA-A2 Stainless Steel A2, with conical bolt and hexagon nut
do td Min. drill-hole depth for through fixing mm hv Min. anchorage depth mm l da Max. fixing thickness mm M SW
Type
Art. No.
Drill mm
Fixing length mm
Thread
8 8 10 10 10 10 12 12 12 12
25 30 30 35 35 35 35 40 40 40
10 25 10 25 55 75 10 25 45 65
10 10 13 13 13 13 17 17 17 17
100 50 50 50 50 50 25 25 20 20
FSA 10/100 A2 60254 FSA 10/120 A2 60255 FSA 12/60 A2 FSA 12/80 A2 60256 60257
Installation examples
Mean ultimate loads and recommended loads for single anchors of fischer Sleeve anchor FSA with large axial spacing and edge distance
Non-cracked concrete Anchor size FSA 8/.. M6 FSA 10/.. M8 40 55 10 14.7 18.7 3.7 6.2 12.9 80 60 80 25 FSA 12.. M 10 50 65 12 21.5 26.1 4.5 8.7 25.7 100 60 100 40
Effective anchorage depth heff [mm] 35 Drill hole depth ho [mm] 50 Drill hole diameter do [mm] 8 Mean ultimate loads Nu,m and Vu,m [kN] Tensile 0 Nu,m [kN] gvz 12.0 Shear 90 Vu,m [kN] gvz 13.2* Recommended loads Nrec and Vrec [kN] Tensile 0 Nrec [kN] gvz 2.8 Shear 90 Vrec [kN] gvz 5.1 Recommended bending moment Mrec [Nm] Mrec [Nm] gvz 5.2 Component dimensions, minimum axial spacings and edge distances 1) Min. axial spacing smin [mm] 70 Min. edge distance1) cmin [mm] 50 Min. structural comp. thickness hmin [mm] 70 Required torque Tinst [Nm] 10
* steel failure 1) For min. axial spacing and min. edge distance the above described loads have to be reduced! (See Technical Handbook or design software CC-Compufix) All load values apply for: concrete compressive strength fc,200 = 30 N/mm2 no edge or spacing influences. Recommended loads: material safety factors M and safety factor for load L = 1.4 are included. Material safety factor M depends on type of anchor.
For detailed design method please contact fischer technical service department.
39
Suitability
Suitable for: Hollow-ceiling slabs of prestressed concrete, concrete B55. For fixing of: All types of anchoring, e.g. cross beams, pipes and ventilation ducts, suspended ceilings, safety engineering, cable trays.
Description
The fischer Hollow-ceiling anchor FHY has been developed specially for fastenings in hollow-ceiling slabs of prestressed concrete. It is designed for use with standard bolts or threaded rods with metric threads from M6 to M10. The Hollow-ceiling anchor FHY is installed flush with the concrete surface. When the bolt or the nut is tightened a tapered element is pulled into the sleeve, which presses this outwards. In this way, the FHY presses against the sides of the hole, creating a friction fit. If the anchor encounters a cavity during installation, the expansion of the sleeve forms a Y shape. The holding power is now the result of a combination of expansion pressure and form-fit. The fischer Hollow-ceiling anchor FHY offers considerable scope in the location of attachment points. Unlike other competing products, it does not have to be located at the centre of the cavity axis, which is often very difficult to define. Instead, it can be located down to a minimum distance of 50 mm from the prestressing steel.
Installation advice
How to determine the length of the screw ls: length of the fischer Hollow-ceiling anchor FHY (+ thickness of the building component da (= length of the screw (+ additional thickness of nut and washer with threaded rods)
do
ls
Approvals
Z-21.1-1711
Tinst
F 120
Installation diagram
40
tfix
hef
Type
Art. No.
Thread
10 12 16
50 60 65
30 35 40
37 43 52
M 6 M 8 M 10
37 43 52
45 55 60
50 25 20
Type
Art. No.
Thread
10 12 16
50 60 65
30 35 40
37 43 52
M 6 M 8 M 10
37 43 52
45 55 60
50 25 20
* in solid materials
Recommended loads1) fixing parameters and component dimensions for tension, shear and diagonal load at any angle in hollow-slab floors of prestressed concrete of strength class B55 or C50/60. When dimensioning, observe the approval Z-21.1-1711 in its entirety. Fixing type Web thickness FHY M 6 du mm 25 < 30 h1 mm mm kN 0.7 kN 0.35 mm mm mm FHY M 8 FHY M 10
Drill hole depth Drill hole diameter Single fixing Perm. F 2) with c ccr1.2 Perm. F 2) with c = cmin1.2 Axial spacing2) ccr1.2 Min. edge distance2) cmin1.2 Axial spacing scr1.2 Pairs of fixings3) Perm. F with c ccr1.2 Perm. F with c = cmin Min. axial spacing smin1.2 Edge distance ccr1.2 Min. edge distance cmin1.2 = Safe working bending moment Grade 4.6 Grade 5.8 Grade 5.8 Length of hexagon-head min ls screw5) Length of threaded bolt min lB Installation torque TInst Through-hole in the component df to be attached
1)
kN 0.7 1.4 2.6 0.7 1.4 2.6 kN 0.35 1.25 2.35 0.35 1.25 2.35 mm 70 80 100 70 80 100 mm 150 mm 100 Nm Nm Nm mm mm Nm mm 4.44) 7.04) 39 + tfix 62 + tfix 10 7 6.4 10.74) 17.14) 45 + tfix 68 + tfix 10 9
2.0 1.8 80
The anchorage of the Cavity Fixing FHY is permissible only in hollow-slab ceilings of prestressed concrete, the width of whose cavities is not more than 4.2 times the web width. The fixing may also be used as multiple fastening for anchoring lightweight ceiling coverings and underceilings to DIN 18168 on hollow-slab ceilings of prestressed concrete, and for statically similar anchorages up to 1.0 kN/m2. When external loads are suspended from the prestressed-concrete hollow-slab ceilings, the shearing loadbearing capacity must be reduced. For fastening lightweight ceiling coverings and underceilings, to DIN 18168, this reduction is not necessary. 2) For edge distances c min < c ccr the permissible loads may be determined by linear interpolation. 3) The permissible load applies for a pair of fixings. The permissible load for the most highly stressed fixing must not exceed the values stated for the single fixing. For pairs of fixings with min axial distances of smin1.2 < s1.2 < scr1.2 the permissible load may be interpolated linearly. The linear value at s1.2 = scr1.2 for the pair of fixings with tensile load applied, may be assumed to be twice the permissible load for the single fixing. 4) Only threaded rods marked in accordance with the approval may be used. 5) With hexagon bolts with shaft to DIN EN 24014, the shaft length must be t . fix
41
fischer Wallbolt GM
The economical heavy-duty anchor
Suitability
Suitable for: Concrete B15 and natural stone with dense structure. For fixing of: Installation rails, ventilation ducts, pipework, suspended ceilings, metal profiles, shelf feet. Also suitable for temporary fastenings such as wall shuttering
1 2 3 4 5
GM S wallbolt - shield only GM H wallbolt - hook bolt type GM P wallbolt - projecting bolt type GM L wallbolt - loose bolt type GM E wallbolt - eye bolt type
Description
The segmented malleable iron expansion shield is assembled ready for use with bolts or threaded rods of the appropriate diameter. Function - torque controlled friction locking expansion. Four piece malleable shield for even load spread. Unique metal spring clip for retaining the segments and the wedge. Traditional fixing method with wide user acceptance. Zinc plated and passivated for corrosion protection. For the best results with the GM anchor remember to: Choose the most suitable accessory. Choose the right sized anchor in relation to load type. Check load bearing capacity values in the table. Make sure the drilled hole is dust free.
Installation diagram
42
fischer Wallbolt GM
Technical data Technical data
Type
Art. No.
Drill mm
Bolt mm
Torque Nm
Type
Art. No.
Drill mm
Bolt mm
Torque Nm
GM 6/10 L GM 6/25 L GM 6/40 L GM 8/10 L GM 8/25 L GM 8/40 L GM 10/10 L GM 10/25 L GM 10/50 L GM 10/75 L GM 12/10 L GM 12/25 L GM 12/50 L GM 12/75 L GM 16/15 L GM 16/30 L GM 16/60 L GM 20/60 L GM 20/100 L GM 24/100 L GM 24/150 L
58001 58002 58003 58004 58005 58006 58007 58008 58009 58010 58011 58012 58013 58014 58015 58016 58017 58018 58019 58021 58022
12 12 12 15 15 15 18 18 18 18 22 22 22 22 29 29 29 36 36 42 42
60 60 60 70 70 70 80 80 80 80 100 100 100 100 130 130 130 170 170 210 210
6 6 6 8 8 8 10 10 10 10 12 12 12 12 16 16 16 20 20 24 24
50 50 50 50 50 50 50 50 50 25 25 25 25 25 10 10 10 10 10 10 10
GM 6 S GM 8 S GM 10 S GM 12 S GM 16 S GM 20 S GM 24 S
12 15 18 22 29 36 42
6 8 10 12 16 20 24
50 50 25 20 10 5 5
Type
Art. No.
Drill mm
Bolt mm
Eye mm
Torque Nm
GM 6 E GM 8 E GM 10 E GM 12 E GM 16 E
12 15 18 22 29
60 70 80 100 130
47 50 60 75 102
6 8 10 12 16
10 25 40 75 180
50 50 25 15 10
Type
Art. No.
Drill mm
GM 6/10 P GM 6/25 P GM 6/60 P GM 8/10 P GM 8/25 P GM 8/60 P GM 10/15 P GM 10/30 P GM 10/60 P GM 12/15 P GM 12/35 P GM 12/75 P GM 16/15 P GM 16/35 P GM 16/75 P GM 20/15 P GM 20/30 P GM 20/100 P GM 24/75 P GM 24/120 P
58030 58031 58032 58033 58034 58035 58036 58037 58038 58039 58040 58041 58042 58043 58044 58045 58046 58047 58048 58049
12 12 12 15 15 15 18 18 18 22 22 22 29 29 29 36 36 36 42 42
60 60 60 70 70 70 80 80 80 100 100 100 130 130 130 170 170 170 210 210
6 6 6 8 8 8 10 10 10 12 12 12 16 16 16 20 20 20 24 24
0 10 0 25 0 60 0 10 0 25 0 60 0 15 0 30 0 60 0 15 0 35 0 75 0 15 0 35 0 75 0 15 0 30 0 100 0 30 0 100
50 50 50 50 50 50 50 25 25 20 20 20 10 10 10 5 5 5 5 5
Type Art. No.
Drill mm
Bolt mm
Hook mm
Torque Nm
GM 6 H GM 8 H GM 10 H GM 12 H GM 16 H
12 14 16 20 29
60 70 80 100 130
47 50 60 75 102
6 8 10 12 16
10 25 40 75 100
50 50 25 15 10
Critical edge distance and critical spacing [mm] Crit. axial spacing a 140 170 Crit. edge distance ar 40 105 Min. axial sp.a min. 80 80 Min. edge dist.armin. 50 50 Min. struct. thickness t 100 100
43
Suitability
Suitable for: Concrete B15 and natural stone with dense structure. For fixing of: Installation rails, ventilation ducts, pipework, suspended ceilings, metal profiles, shelf feet. Also suitable for temporary fixings such as wall shuttering
1 2 3 4 5
FWB S wallbolt - shield only FWB L wallbolt - loose bolt type FWB P wallbolt - projecting bolt type FWB H wallbolt - hook bolt type FWB E wallbolt - eye bolt type
Description
The segmented steel expander shield is assembled ready for use with bolts or threaded rods of the appropriate diameter.
Function - torque controlled friction locking expansion. Three piece shield for even load spread. Traditional fixing method with wide user acceptance. Zinc plated and passivated for corrosive protection. The versatile heavy-duty fixing !
4 3
Installation instructions
Determination of the screw length l s: length of the fischer Heavy-duty anchor FWB + thickness of the building component da = length of the screw (in the case of threaded bolts additionally include + thickness of washer and nut)
Installation diagram
44
Type
Art. No.
Drill mm
Torque Nm
Drill mm
Bolt mm
Torque Nm
FWB 6/10 L FWB 6/25 L FWB 6/40 L FWB 8/10 L FWB 8/25 L FWB 8/40 L FWB 10/10 L FWB 10/25 L FWB 10/50 L FWB 10/75 L FWB 12/10 L FWB 12/25 L FWB 12/40 L FWB 12/60 L FWB 16/15 L FWB 16/30 L FWB 16/60 L FWB 20/60 L
58156 58157 58158 58159 58160 58161 58162 58163 58164 58165 58166 58167 58168 58169 58170 58171 58172 58173
12 12 12 14 14 14 16 16 16 16 20 20 20 20 25 25 25 32 32
6 6 6 8 8 8 10 10 10 10 12 12 12 12 16 16 16 20 20
0 10 0 25 0 40 0 10 0 25 0 40 0 10 0 25 0 50 25 75 0 10 0 25 0 50 25 75 0 15 0 30 25 60 20 60 60 100
50 50 50 50 50 50 50 50 50 25 25 25 25 25 10 10 10 10 10
12 14 16 20 25 32
50 55 65 85 130 150
45 50 60 75 115 130
6 8 10 12 16 20
10 25 40 75 180 345
50 50 50 25 10 10
Type
Art. No.
Drill mm
Bolt mm
Eye mm
Torque Nm
12 14 16 20 25
50 55 65 85 130
45 50 60 75 115
6 8 10 12 16
10 12 14 17 23
10 25 40 75 180
50 50 25 25 10
Type
Art. No.
Drill mm
Torque Nm
FWB 6/10 P FWB 6/25 P FWB 6/60 P FWB 8/10 P FWB 8/25 P FWB 8/60 P FWB 10/15 P FWB 10/30 P FWB 10/60 P FWB 12/15 P FWB 12/35 P FWB 12/75 P FWB 16/15 P FWB 16/35 P FWB 16/75 P FWB 20/15 P FWB 20/30 P
58175 58176 58177 58178 58179 58180 58181 58182 58183 58184 58185 58186 58187 58188 58189 58190 58191
12 12 12 14 14 14 16 16 16 20 20 20 25 25 25 32 32 32
6 6 6 8 8 8 10 10 10 12 12 12 16 16 16 20 20 20
0 10 0 25 0 60 0 10 0 25 0 60 0 15 0 30 0 60 0 15 0 35 0 75 0 15 0 35 0 75 0 15 0 30 0 100
50 50 50 50 50 25 50 25 25 25 25 25 10 10 10 10 10 10
Type
Art. No.
Drill mm
Bolt mm
Hook mm
Torque Nm
12 14 16 20
50 55 65 85
45 50 60 75
6 8 10 12
8 10 12 16
10 25 40 75
50 50 25 25
45
Suitability
Suitable for: Concrete B15 For fixing of: Flat steel, profiled steel, pipelines, suspended ceilings, ventilation pipes, sprinkler systems, threaded rods, assembly support, gratings, facades, diamond drilling devices (EA-D), etc.
Hammerset anchor EA
Description
The fischer Hammerset anchor EA is a compact internally threaded fixing for attachment assembly, made of zinc plated steel for metric threads M 6 to M 20. The sizes M 6 to M 16 are also available in stainless steel. It is universally easy to use and offers the following: Economical fixing Shallow drill-hole depth displacement controlled impact expansion favourable ratio of thread/drill-hole diameter The fischer Hammerset anchor EA forms a flush seal with the concrete surface and permits replacement of the mounted item without influencing the expansion force. The setting method of tapping in and price/performance ratio have made the EA anchor a standard metal fixing most acoustics installers, heating, ventilation and sanitary equipment installers, metal constructors and fitters
Installation advice
It is essential to adhere to the drill-hole depth and drill diameter. The cone must only be driven with the setting tool EAWH (narrow-end) into the anchor sleeve. The cone must be driven into the anchor sleeve until the tool collar lies on the anchor body.
The screw length must be carefully determined: min. screw-in depth + thickness of the building component = screw length (with threaded bolt, include thickness of washer and nut) If the screw is too long: No tighteneing of the fixing is possible, since screw reaches end of thread. If the screw is too short: Thread load-bearing capacity too low.
Approvals
Z-21.1-1619
t = hv
Approved for the tension zone, light suspended ceilings and ceiling covers.
da MD
do
Recognised for use with fixed water sprinkler systems from M8.
e ls
EA M 8 x 40 M 10, M 12
Fire resistance classification
= da + e
Dossier NPO.021
F 120
Installation diagram
46
Installation examples
Type
Art. No.
Thread
EA M 61) EA M 8 EA M 8 x 40 EA M 10 EA M 12 EA M 16 EA M 20
8 10 10 12 15 20 25
25 30 40 40 50 65 80
25 30 40 40 50 65 80
25 30 40 40 50 65 80
M 6 M 8 M 8 M 10 M 12 M 16 M 20
6 8 8 10 12 16 20
12 13 20 17 22 27 34
100 100 50 50 25 20 10
EA A4 stainless steel (material: 1.4401), not suitable for diamond drilling devices and diamond saws EA M 6 A41) EA M 8 A41) EA M 10 A4 EA M 12 A4 EA M 16 A4 60825 60826 60827 60828 60829 8 10 12 15 20 25 30 40 50 65 25 30 40 50 65 25 30 40 50 65 M 6 M 8 M 10 M 12 M 16 6 8 10 12 16 12 13 17 22 27 100 100 50 25 20
Hammerset tools
EAW H 6 EAW H 8 EAW H 8 x 40 EAW H 10 EAW H 12 EAW H 16 EAW H 20 60836 60837 60846 60838 60839 60841 60843 Fits EA M 6 Fits EA M 8 Fits EA M 8 x 40 Fits EA M 10 Fits EA M 12 Fits EA M 16 Fits EA M 20 1 1 1 1 1 1 1
Mean ultimate loads and recommended loads for single anchors of fischer Hammerset anchor EA with large axial spacing and edge distance
Non-cracked concrete Anchor size Effective anchorage depth Drill hole depth Drill hole diameter Mean ultimate loads Nu,m and Vu,m [kN] Tensile 0 Shear 90 heff h1 = do Nu,m Vu,m [mm] [mm] [mm] [kN] [kN] [kN] [kN] gvz A4 gvz A4 M6 25 27 8 10.1* 12.0 6.0* 8.1* M8 30 33 10 14.0 14.0 10.2* 9.8* M8 x 40 40 43 10 16.3 10.2* M10 40 44 12 18.6 18.6 11.7* 12.4* M12 50 54 15 32.0 32.0 21.2* 22.5* 6.5 6.5 10.2 8.8 28.1 42.1 140 150 150 35 M16 65 71 20 40.0 40.0 31.4* 36.8* 9.5 9.5 12.4 14.4 71.4 107 170 220 200 60 M20 80 86 25 66.0 50.3* 13.0 20.0 139 200 240 240 120 M6 25 27 8 0.5 0.5 400 100 100 2 M8 30 33 10 0.5 0.5 400 100 100 3 Cracked concrete1) M8 x 40 40 43 10 0.8 0.8 400 100 100 3 M10 40 44 12 0.8 0.8 400 200 100 6 M12 50 54 15 0.8 0.8 400 200 100 15
[kN] gvz 2.3 3.0 4.0 4.5 [kN] A4 2.3 3.0 4.5 Shear 90 Vrec [kN] gvz 2.9 4.8 4.8 5.6 [kN] A4 3.2 3.9 4.8 Recommended bending moment Mrec [Nm], values apply to screws with a strength classification 5.6 and A4-70 respectively Mrec [Nm] gvz 3.3 8.0 8.0 16.0 [Nm] A4 4.9 12.1 12.1 24.1 Component dimensions, minimum axial spacings and edge distances Min. axial spacing2) smin [mm] 70 80 100 100 Min. edge distance2) cmin [mm] 80 90 120 120 Min. structural component thickness hmin [mm] 100 100 120 120 Required torque Tinst [Nm] 4 8 8 15
Nrec
* steel failure, values apply to screws with a strength classification 5.6 and A4-70 respectively. 1) For the fixing of lightweight suspended ceiling constructions only. 2) For min. axial spacing and min. edge distance the above described loads have to be reduced! (See Technical Handbook or design software CC-Compufix) All load values apply for: concrete compressive strength fc,200 = 30 N/mm2 no edge or spacing influences. Recommended loads: material safety factors M and safety factor for load L = 1.4 are included. Material safety factor M depends on type of anchor.
The conditions of application differ from those given in the German approval. For further detailed information about German approval please contact fischer technical service department.
47
Ceiling anchor
Suitability
Suitable for: Concrete B15 and dense natural stone plus hollow core slabs For fixing of: ideal for fastening with bolts or threaded rods for plumbing, air-conditioning, heating and ventilation installations. Available in zinc plated.
Suitability
Suitable for: Concrete B15 and dense natural stone For fixing of: ideal for fastening suspended ceiling wires or brackets.
Description
A ceiling anchor for rapid installation, with high retaining power. The wedge shaped segments move over each other during insertion, wedging the nail in the hole.
Description
A drop-in anchor with rim so that the anchor always remains flush with the surface of the substrate. The drill hole can now be overdepth without effecting the anchor
Technical data
do drill-hole Type Art. No. Drill mm depth for through fixing mm Fixing length mm Quantity per pack td Min. l
Technical data
do td Min. drill-hole depth for through fixing mm l . Fixing length mm Quantity per pack
Type
Art. No.
Drill mm
8 10 12
27 32 33
25 30 30
78644 78645
6 6
40 40
35.0 35.0
100 100
Mean ultimate loads in kN. Use 80% of EA loads, see page 47.
Mean ultimate loads in kN. An appropriate safety coefficient must be allowed on these breaking values (see page 16).
Anchoring base Concrete B 25 FDN 0.5
A rim for the accurate setting of the anchor flush to the surface, not dependant on hole depth.
Installation diagram
48
Suitability
Suitable for: Concrete B25, solid brick, pressure-resistant natural stone, lightweight building materials. For fixing of: Board sub-structures, metal sheets and profiles, small items in building interiors
Installation example
Description
The FNH nail sleeve is a fast and economical fastening made of dacromet-coated sprung steel. Especially suitable for small items in building interiors. When pushed through the object being installed, the sleeve expands over its entire length in the hole. Simple and timesaving. The object is held by its collar. No screws required.
do
Technical data
h ef
do td Min. drill-hole depth for through fixing mm hef Effect. anchorage depth mm l tfix Max. fixing thickness mm
tfix td
Type
Art. no.
Drill mm
Fixing length mm
FNH 5/50 FNH 6/30 FNH 6/40 FNH 6/50 FNH 6/60 FNH 6/80 FNH 8/70 FNH 8/90 FNH 8/110 FNH 8/130 FNH 8/150
50192 19863 50638 77525 19864 19865 19866 19867 19868 19869 19870
5 6 6 6 6 6 8 8 8 8 8
20 30 30 30 30 30 40 40 40 40 40
30 10 20 30 50 30 50 70 90 110
Recommended loads: material safety factors M and safety factor for load L = 1.4 are included. Material safety factor M depends on type of anchor.
Installation diagram
49
Suitability
Suitable for: Concrete B15. For fixing of: Laths, squared timber beams, battens, wood substructures, metal profiles, chains, cables, punched tapes, wire hangers, extension nuts with threaded rods, fire partitions, ventilation pipes, suspended ceilings, C-rails, ceiling insulation on light wood-wool boards, etc.
1 2 3 4 5
with nail head with M6 + M8 thread with eye with hook for rail fixing
Material: zinc plated and passivated steel, A4 stainless steel and high corrosion resistant steel 1.4529 - see page 52/53.
1
Description
The fischer Nail Anchor can be installed swiftly and smoothly, a real advantage for overhead work. Low drilling expenditure, only 6 mm diameter. Easy tap-in assembly, two hammer blows are sufficient. All building site requirements are available. Building inspectorate approval for more safety.
Advantages
FNA with nail head: For battens and metal hangers. The nail head can be effortlessly sunk into timber with one blow. On metal parts, it covers a large surface area, giving a clean finish. Longer useful lengths bridge non-load-bearing layers. FNA with M 6 + M 8 thread: For all demountable connections with metric thread. Connection of threaded hanger rods is possible by means of extension couplers. Longer threaded portion enables bridging of non-load bearing layers such as plaster or insulation. FNA with eye: For anchoring of hangers, punched tapes, cables or chains. FNA with hook*: For suspending chains, lamps, cable loops, rings or other closed parts. FNA for rail fixing:
5
Enables quick and easy installation of lightweight railing. *Not an element of the building inspectorate approval.
Approvals
Z-21.1-606
Approved for the tension zone, light suspended ceilings and ceiling covers.
F 60/90/120
Installation diagram
50
Installation examples
Type
FNA 6 x 30/ 5 FNA 6 x 30/ 30 FNA 6 x 30/ 50 FNA 6 x 30/ 75 FNA 6 x 30/100 FNA 6 x 30/120 FNA 6 x 40/ 5
77802* 77805*
6 6 6 6 6 6 6
30 30 30 30 30 30 40
5 30 50 75 100 120 5
100 50 50 50 50 50 50
* not included in building inspectorate approval with thread M 6 and M 8 FNA 6 x 30 M 6/5**50920 FNA 6 x 40 M 8/5**50951 77806* 6 6 50 55 30 40 52 55 5 5 M 6 10 M 8 13 100 50
Mean ultimate loads and recommended loads for single anchors of fischer Nail anchor FNA with large axial spacing and edge distance
Non-cracked concrete Anchor size FNA 6x30 6x40 heff ho do Nu,m Nu,m Vu,m Vu,m [mm] [mm] [mm] [kN] [kN] [kN] [kN] gvz A4 gvz A4 30 45 6 5.0* 5.6* 3.0 6.3 FNA 6x40 M 8/5 40 55 6 5.0* 9.8* 2.4 5.1 120 80 100 4 Cracked concrete1) FNA 6x30 6x40 30 45 6 0.5 0.5 1.0 1.0 60 50 100 4 FNA 6x40 M 8/5 40 55 6 0.8 1.6 80 60 100 4
Effective anchorage depth Drill hole depth Drill hole diameter Mean ultimate loads Nu,m [kN] Tensile2) Shear2) Recommended loads Nrec [kN] Tensile2) Shear2)
Nrec [kN] gvz 2.1 Nrec [kN] A4 2,1 Vrec [kN] gvz 1.7 Vrec [kN] A4 2.9 Component dimensions, minimum axial spacings and edge distances Min. axial spacing3) smin [mm] 100 Min. edge distance3) cmin [mm] 60 Min. structural comp. thickness hmin [mm] 100 Required torque Tinst [Nm] 4
* steel failure decisive 1) For the fixing of lightweight suspended ceiling constructions only. 2) Loads are not valid for the anchor type FNA with hook. 3) For min. axial spacing and min. edge distance the above described loads have to be reduced! (See Technical Handbook or design software CC-Compufix) All load values apply for: concrete compressive strength fc,200 = 30 N/mm2 no edge or spacing influences. Recommended loads: material safety factors M and safety factor for load L = 1.4 are included. Material safety factor M depends on type of anchor.
The condition of application differ from those given in the German approval. For detailed design method and design in accordance with German approval please contact fischer technical service department.
51
Suitability
Suitable for: Concrete B15. For fixing of: Ventilation systems, pipelines, cable trays in road tunnels, installations and suspended ceilings in indoor swimming pools, steel structures and other mountings in bridge areas as well as in the chemical industry etc.
1 2 3 4 5 6 7
Zykon anchors FZA C Zykon hammerset anchors FZEA C Threaded rods RG M C Threaded rods FIS G C Highbond anchor FHB-A C Nail anchor FNA C Anchor Bolt FAZ - C
Description
In atmospheres with high chloride, sulphur-dioxide and humidity contents, the risk of corrosion is high due to the concentration of contaminants. For safe and durable fixing, fischer now offers steel anchors which are able to withstand especially corrosive environmental conditions. These new fastening elements are made of high-alloy steel with material number 1.4529. In material approval Z-30.3-6, this highly corrosion-resistant steel has the highest resistance classification of IV.
Advantages
Fast and safe anchoring is now possible in areas which were not previously included in the approval. The various areas of application are regulated in the approval thereby allowing maximum planning safety even in critical cases. With the FZA Zykon Anchor, the FZEA Zykon Hammerset Anchor, the FHB Highbond Anchor and the FNA Nail Anchor, fischer now offers fixing elements of material 1.4529 which are suitable for use in the tension zone.
Approvals
Z-21.1-958 Z-21.3-1615
The right anchor for every fixing task. Whether as bolt, push-through, interior-thread or synthetic-resin anchor, fischer has the right fixing for your purpose. In long years of research, fischer has accumulated an unequalled expertise in this field which we are happy to pass on to our customers. Just contact our field engineers. We manufacture job-specific products to your requirements. This guarantees you maximum flexibility, even with special dimensions.
FZA
FZEA
R + ETA option 8
Z-21.3-1707
FHB
FNA
FAZ
52
Technical data
Highbond anchor FHB-A C
do
ho Drillhole depth mm
Type
Art. No.
Drill mm
Type
Art. No.
Drill mm
da Fixing thickness mm
SW
Thread
Hexagon nut
Required resin
FHB-A 10 x 60/10 C FHB-A 10 x 60/60 C FHB-A 12 x 80/10 C FHB-A 12 x 80/60 C FHB-A 12 x 100/25 C FHB-A 12 x 100/60 C FHB-A 16 x 125/30 C FHB-A 16 x 125/60 C FHB-A 20 x 170/50 C FHB-A 24 x 220/50 C
62401 62402 62403 62404 62405 62406 62408 62407 62409 62418
12 12 14 14 14 14 18 18 24 28
10 60 10 60 25 60 30 60 50 50
10 10 12 12 12 12 16 16 20 24
17 17 19 19 19 19 24 24 30 36
* * * * * * * * * *
10 10 10 10 10 10 10 10 10 5
FZA 10 x 40 M 6/10 C* FZA 10 x 40 M 6/35 C FZA 12 x 40 M 8/15 C FZA 14 x 40 M 10/25 C FZA 12 x 50 M 8/15 C* FZA 12 x 50 M 8/50 C FZA 14 x 60 M 10/25 C* FZA 14 x 60 M 10/50 C FZA 18 x 80 M 12/25 C* FZA 18 x 80 M 12/55 C FZA 22 x 100 M 16/60 C FZA 22 x 125 M 16/60 C FZA 12 x 50 M 8 D/10 C FZA 12 x 60 M 8 D/10 C FZA 12 x 80 M 8 D/30 C FZA 14 x 80 M 10 D/20 C FZA 18 x 100 M 12 D/20 C FZA 18 x 130 M 12 D/50 C
96214 96361 96215 96228 96227 96362 96216 96358 96315 96359 96364 96360 96319 96353 96354 96355 96356 96357
10 10 12 14 12 12 14 14 18 18 22 22 12 12 12 14 18 18
40 40 40 40 50 50 60 60 80 80 100 125 40 50 50 60 80 80
10 35 15 25 15 50 25 50 25 55 60 60 10 10 30 20 20 50
M 6 M 6 M 8 M 10 M 8 M 8 M 10 M 10 M 12 M 12 M 16 M 16 M 8 M 8 M 8 M 10 M 12 M 12
10 10 13 17 13 13 17 17 19 19 24 24 13 13 13 17 19 19
25 25 25 25 20 20 10 10 10 10 10 6 25 25 25 10 10 10
* For the correct resins FIS HB 345 S and FIS HB 150 C, see page 2. Prices, delivery times and other dimensions available on request. Nail anchor FNA
* Article available from stock. Prices, delivery times and other dimensions available on request. Hammerset anchor FZEA C
Type
Art. No.
Drill mm
Thread
77807 77808
6 6 6
50 75 50
30 30 30
45 71 52
5 30 5
M6
10
100 50 100
Installation examples
10 12 14
40 40 40
M 8 M 10 M 12
11 13 15
17 19 21
100 100 50
* Article available from stock. Prices, delivery times and other dimensions available on request. Resin anchor threaded rod RG M C
Material 1.4529
approval - see page 13
Available with glass capsule RM or injection resin FIS V, both with ETA
Type
Art. No.
Drill mm
10 12 14 18
80 90 110 125
80 90 110 125
13 20 25 35
13 17 19 24
10 10 10 10
* Article available from stock. Prices, delivery times and other dimensions available on request.
Information on this product range and sizes was not available at time of printing. For further details please contact fischer customer services 01491 827900
53
54