You are on page 1of 7

1.

A certain appliance use 350W, if it is allowed to run continous for 24 days , how many kwH of energy does it consume (fill in the blank) Ans-350*24*24/1000 = 201.6 2.open loop <<>> function of a sys has zero with positive real value is called NON MINIMUM phase function 3.If an intrinsic semiconductor is doped with a very small amount of boron then the extrinsic semiconductor set formed ,the no. of electrons and holes will A.bothdec B.increase and decrease C.Both increase D.Decrease and increase 4.when the current through the coil of an electromagnet is reversed, the direction of magnetic field also reversed (TRUE or FALSE) 5.A poly phase motor driving an engine room pump fails to start, when trying to identify the cause of failure, which of the following steps are applicable.(multiple ans) A.visually examine the motor for open circuit fault B. visually examine the stator for open circuit fault C.Reverse the direction of current for its working D.Perform the infinite resistance test 6. with reference to the data logger for a refrigerate sys. Which of the parameters should be noted? A.sea water temp, pressure B.condenser temp C.Refrigerent leakage D.Evaporator temp

7. When a thermal acting breaker is required to be used in a area of usually high,low and constant fluctuating temp. as ambient compensation <<>> must be used.the element consists of A. cylindrical spring on the constant area B. Conical spring . C. Secondary bimetal element Delectro magnet

8.the voltage induced across a certain coil is 150 mA. a 100 ?? resistor is connected to the coil terminal calculate induced current in Milli Ampere ?????? ans-

9.Which of the listed precautions should be taken when cleaning the internals of a motor with

compressed air? A. Open the machine on both ends so as to allow the air and dust to escape. B. Be certain that the circuit breaker is opened and tagged on the feeder panel. C. Be certain that the air is clean and as dry as possible. D. Ensure that the fuse in the motor is removed. 10.When reading electrical motor controller diagrams, it helps to know that ____________. A. current paths in the control circuit are drawn as heavy lines and in the power circuit as lighter lines B. current paths in the power circuit are drawn as heavy lines and in control circuit as lighter lines C. circuits subject to 500 volts or greater are drawn as heavy lines and below 500 volts as lighter lines D. circuits subject to 500 volts or greater are drawn as light lines and below 500 volts as heavy

11. In a Transistor A.PNP and NPN are two basic types B.Emitter,Collector and Base are the basic Elements. C.Collector separates Base and Emitter D.Emitter separates Base and Collector 12. Tightly knit metal braid wire can be used with a printed circuit board when A. Conductor flexibility is required B. De-soldering components in the circuit C. Electrically produced magnetic fluxes would cause inaccuracies in adjacent components D. Reactance in the circuit must be kept to a minimum 13.When paralleling an AC generator with live bus bars, which of the following precautions are applicable? A. Generator frequency should be slightly lower than bus bar frequency B. Generator frequency should be slightly higher than bus bar frequency C. Generator voltage should be in phase with bus bar voltage D. Generator voltage should be out of phase with bus bar voltage

14. For leading power factor circuits, which of the following can be used? A. Shunt Capacitors only B. Shunt Reactors only C. Either Shunt Capacitors or Shunt Reactors D. Neither Shunt Capacitors Nor Shunt Reactors 15. A moulded-case breaker provides protection against short-circuits by usinga/an A. Shading coil. B. Arc quencher.

C. Electromagnet. D. Holding coil. 16. Fuses placed in series with a thermal trip = - type circuit breaker are used for A. Time-delay protection B. Short-circuit protection C. Short duration surge protection D. Sustained overload protection 17. Open-loop transfer function of a system having one zero with positive real values is called (1)_NON MINIMUM_______ 18. What is the magnetomotive force in a 75-turn coil of wire when there are 4 A of current through it? Ans MF=NI; MF=75*4=300A 19.If it takes 35 J of energy to move a charge of 6 C from one point to another, what is the voltage between the two points? Your answer should be correct to two decimals. ANS 5.83 20. The basic measuring unit of inductance is the A. coulomb B.ohm C. farad D. henry

21. The greatest detrimental effect on idle electrical equipment, such as cargo pump motors,is the A. Loss of residual magnetism. B. Absorption of moisture in the insulation. C. Insulation varnish flaking. D. Dirt collecting on the windings. 22. .In what range of voltages is the transistor in the linear region of its operation? A.0 &lt; VCE &lt; 0.7 V B.0.7 &lt; VCE &lt; 1.4 V C.0.7 &lt; VCE &lt; VCE(max) D.0 &lt; VCE &lt; VCE(max) 23. The current in a semiconductor is produced by: A. Electrons B. Neutrons C. Protons D. Holes

24 .AC circuits possess characteristics of resistance, inductance, and capacitance. The capacitive reactance of a circuit is expressed in A. ohms B. mhos C. henrys D. farads 25. Brushless generators are designed to operate without the use of A. brushes B. Slip rings C. commutators D. all of the above 26. A fuse that blows often should be replaced only with a fuse of A. the recommended current and voltage rating B .higher current and voltage rating C. higher current and lower voltage rating D. lower current and higher voltage rating 27. for leading power factor circuits, which of the following can be used? A. Shunt Capacitors only B. Shunt Reactors only C. Either Shunt Capacitors or Shunt Reactors D. Neither Shunt Capacitors nor Shunt Reactors 28. A certain appliance uses 750 W. If it is allowed to run continuously for 15 days, how many kilowatt-hours of energy does it consume? Ans- 750*15*24/1000 = 270 KwH 29. Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum. 30. Tightly knit metal braid wire can be used with a printed circuit board when A. Conductor flexibility is required B. De-soldering components in the circuit C. Electrically produced magnetic fluxes would cause inaccuracies in adjacent components D. Reactance in the circuit must be kept to a minimum 31. With reference to a Data Logger for a refrigeration system, which of the following parameters should be monitored? A. Room temperature. B. Liquid Line temperature

C. Recharge temperature. D. Solenoid valve operation.

Set-II
1. Which of the following statements is true concerning a poly-phase synchronous

propulsion motor? A. The motor is started as an induction motor. B. Resistance is gradually added to the rotor circuit. C.T he starting current is held below the rated current. D. The field winding is energized for starting purposes only. 2. When reading electrical motor controller diagrams, it helps to know that ____________. A. current paths in the control circuit are drawn as heavy lines and in the power circuit as lighter lines B. current paths in the power circuit are drawn as heavy lines and in control circuit as lighter lines C. circuits subject to 500 volts or greater are drawn as heavy lines and below 500 volts as lighter lines. D. circuits subject to 500 volts or greater are drawn as light lines and below 500 volts as heavy 3.Alternating current circuits develop resistance, inductance and capacitance. The inductance of a coil is expressed in _____________. A. ohms B. mhos C. henrys D. farads 4.Large cable sizes are formed as individual conductors that may be comprised of several smaller strands to __________. A. obtain the flexibility required for easy handling B. reduce the overall weight of the wire run C. reduce the number of supports needed for a horizontal overhead run D. all of the above

5.Which of the following is having Di-Electric Constant 80? A. Air B. water C. Mica D. Caster oil 6.Where a thermal-acting breaker is required to be used in an area of unusually high, low, or constantly fluctuating temperatures, an ambient compensating element must be used. This element consists of a ______________. A. cylindrical spring on the contact arm B. conical spring on the contact arm C. second bimetal element

D. second electromagnet

7.Which of the following precautions should you take when securing propulsion generators and motors for an extended period of time? A. Disconnect the brush pigtails from their contacts and circulate air through the units. B. Disconnect the brush pigtails from their contacts and discharge carbon dioxide into the units to keep them dry. C. Lift the brushes from commutator collector rings and use the built-in heater to prevent moisture accumulation. D. Lift the brushes from commutator collector rings and circulate cool dry air through the units. 8. The direction of magnetic flux changes when the direction of current is reversed. True / False

9.In a Transistor A.PNP and NPN are two basic types B. Emitter, Collector and Base are the basic Elements. C. Collector separates Base and Emitter D. Emitter separates Base and Collector 9. In a P-Type Semiconductor, the majority current Carriers are ___________. 10. In a Control Loop System, having Zero(0) Positive Real Values are called _NON MINIMUM___________. 11. If a Motor is not rotating in the E/R, you will carry out the following Checks (multiple choice, 3 Questions of same type but Options were different ) A. Check for the isolation B. Rotate the Coupling with your hand C. Check for the Circuit breaker D. Remove the fuses E Look for the Overload Trip F. Visually Inspect the motor terminals G. Visually Inspect the Starter Terminals H. Carry out Infinite Resistance Test 14. Calculate the Velocity of the conductor (up to 0 decimal places), if terminal voltage is 2.2 V/m and the magnetic field strength is 0.2 T. . 15. Calculate the frequency of the motor ( up to 0 decimal places),, if the speed if 4800 Rpm and number of Poles is 2. Ans V=120*f/P ; f=4800*2/120= 80Hz 16. If the resistance of any coil is 120 Ohm. Calculate the Resistance (up to 0 decimal places), when its Length is increased by 20% and its Diameter is increased by 50%.

17. What is the power in a Resistor in Milli Watts (up to 0 decimal places), having Resistance of 12 Ohm having a Potential Difference of 3 V. 18. Resistance of a wire is increased if the Length is____ and Area is _____. 19. Arrange the following in Increasing Order of their Doping Strength. Answer is-Base, collector, emitter A. Collector, Emitter, Base B. Base, Emitter, Collector C. Emitter, Base, Collector D. Emitter, Collector, Collector Base, Collector, Base

You might also like