Professional Documents
Culture Documents
SPECIFICATIONS
V-16, 4-Stroke-Cycle-Diesel
Emissions . . . . . . . . . . . . . . . . . . . . . . . . . . . . IMO compliant Bore. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170.0 mm (6.7 in) Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 215.0 mm (8.5 in) Displacement . . . . . . . . . . . . . . . . . . . . . . . . 78.1 L (4766 in3) Rotation (from flywheel end) . . . . . . . . . . Counterclockwise Compression Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14.7:1 Capacity for Liquids Cooling System (engine only). . . . . 233.4 L (61.6 gal) Lube Oil System (refill) . . . . . . . . . . . . . . 204 L (53 gal) Oil Change Interval . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250 hr Minimum Lube Oil Grade (required) . . . . . . . . . . . . . . CH-4 Weight, Net Dry (LW configuration approx) . . . . . . . . 7878 kg (17,370 lb) (Comm configuration approx) . . . . . 8745 kg (19,280 lb)
LEHM5034-02
3516C HD
MARINE ENGINE PERFORMANCE
D Rating (Intermittent Duty)
2600 2500 2400 2200 2000 1800 Power - bkW 1600 1400 1200 1000 800 600 400 200 0 600 800 1000 1200 1400 1600 1800 2000 2200 2400 Engine Speed - rpm
Engine Speed rpm Zone 1 Curve: 1 1825 1600 1500 1300 1100 900 650 1815 1640 1500 1300 1100 900 650 1810 1730 1500 1300 1100 900 650 Engine Power bkW 1900 1776 1776 1600 831 455 172 2122 1912 1912 1700 831 455 172 2349 2245 2245 1700 831 455 172 Engine Speed rpm D Rating Power Curve: 4 1800 1500 1300 1100 900 650 1800 1500 1300 1100 900 650 Engine Power bkW 2525 2525 1905 872 586 172 2525 1461 951 576 316 119
ZONE 4
MARINE ENGINE
1 2 3 4
ZONE 3
ZONE 2
ZONE 1
BSFC g/bkW 199 196 193 202 207 230 255 198 197 195 202 207 230 255 202 202 202 192 214 230 255
Fuel Rate l/h 446 414 408 385 205 125 52 501 448 444 409 205 125 52 566 541 541 389 212 125 52
BSFC g/bkW 205 201 192 214 235 255 205 199 210 217 233 255
Fuel Rate l/h 602 605 436 222 164 52 602 347 238 149 88 36
Zone 2 Curve: 2
Zone 3 Curve: 3
Zone 1 Continuous operation allowed without interruption or load cycling. Zone 2 Operation is permitted for periods up to four hours, followed by a one-hour period at a combination of power and speed in Zone 1. Zone 3 Operation is permitted for periods up to one hour, followed by a one-hour period at combinations of power and speed in Zone 1.
Zone 4 Operation in Zone 4 is limited to no more than 16% of the total operating hours.
LEHM5034-02
Page 2 of 4
3516C HD
DIMENSIONS
MARINE ENGINE
03
03 W H 01
01
01
03
Engine Dimensions Length Width Height Weight, Net Dry (LW configuration approx) (Comm configuration approx) 3759 mm 2232 mm 2065 mm 7878 kg 8745 kg 148 in 88 in 81 in 17,370 lb 19,280 lb
Note: Do not use for installation design. See general dimension drawings for detail (Drawing #276-0041).
03
LEHM5034-02
Page 3 of 4
3516C HD
RATING DEFINITIONS AND CONDITIONS
D RATING (Intermittent Duty)
RATINGS are based on SAE J1228/ISO8665 standard conditions of 100 kPa (29.61 in Hg), 25C (77F), and 30% relative humidity. These ratings also apply at ISO3046/1, DIN6271/3, and BS5514 conditions of 100 kPa (29.61 in Hg), 27C (81F), and 60% relative humidity. Ratings are valid for air cleaner inlet temperatures up to and including 45C (113F) and for sea water temperatures up to and including 32C (90F) at sea level.
MARINE ENGINE
FUEL RATES are based on fuel oil of 35 API [16C (60F)] gravity having an LHV of 42 780 kJ/kg (18,390 Btu/lb) when used at 29C (85F) and weighing 838.9 g/liter (7.001 lbs/U.S. gal). Fuel consumption shown with all oil, fuel, and water pumps, engine driven. For a without pumps condition, deduct approximately 0.5% for each pump not engine driven. Fuel consumption is nominal data with a tolerance of 3%. Additional ratings may be available for specific customer requirements. Consult your Caterpillar representative for additional information.
Performance data is calculated in accordance with tolerances and conditions stated in this specification sheet and is only intended for purposes of comparison with other manufacturers engines. Actual engine performance may vary according to the particular application of the engine and operating conditions beyond Caterpillars control. Power produced at the flywheel will be within standard tolerances up to 50C (122F) combustion air temperature measured at the air cleaner inlet, and fuel temperature up to 52C (125F) measured at the fuel filter base. Power rated in accordance with NMMA procedure as crankshaft power. Reduce crankshaft power by 3% for propeller shaft power. CAT, CATERPILLAR, their respective logos and Caterpillar Yellow, as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission. 2005 Caterpillar All rights reserved. Materials and specifications are subject to change without notice. The International System of Units (SI) is used in this publication.