You are on page 1of 22

FOD3120 High Noise Immunity, 2.

5A Output Current, Gate Drive Optocoupler

October 2009

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler
Features
High noise immunity characterized by 35kV/s

Description
The FOD3120 is a 2.5A Output Current Gate Drive Optocoupler, capable of driving most 1200V/20A IGBT/MOSFET. It is ideally suited for fast switching driving of power IGBT and MOSFETs used in motor control inverter applications, and high performance power system.
It utilizes Fairchilds proprietary coplanar packaging technology, Optoplanar, and optimized IC design to achieve high noise immunity, characterized by high common mode rejection.

minimum common mode rejection 2.5A peak output current driving capability for most 1200V/20A IGBT Use of P-channel MOSFETs at output stage enables output voltage swing close to the supply rail Wide supply voltage range from 15V to 30V Fast switching speed 400ns max. propagation delay 100ns max. pulse width distortion Under Voltage LockOut (UVLO) with hysteresis Extended industrial temperate range, -40C to 100C temperature range Safety and regulatory approved UL1577, 5000 VRMS for 1 min. IEC60747-5-2 RDS(ON) of 1 (typ.) offers lower power dissipation >8.0mm clearance and creepage distance (option T or TS) 1,414V Peak Working Insulation Voltage (VIORM)

It consists of a gallium aluminum arsenide (AlGaAs) light emitting diode optically coupled to an integrated circuit with a high-speed driver for push-pull MOSFET output stage.

Related Resources
FOD3150, 1A Output Current, Gate Drive

Optocoupler Datasheet www.fairchildsemi.com/products/opto/

Applications

Industrial inverter Uninterruptible power supply Induction heating Isolated IGBT/Power MOSFET gate drive

Functional Block Diagram


NC 1
8 VCC

Package Outlines

8
1 1

ANODE 2

7 VO2 6 VO1

CATHODE 3

NC 4

5 VEE

8 1

8 1

Note: A 0.1F bypass capacitor must be connected between pins 5 and 8.


2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Truth Table
LED
Off On On On

VCC VEE Positive Going (Turn-on)


0V to 30V 0V to 11.5V 11.5V to 13.5V 13.5V to 30V

VCC VEE Negative Going (Turn-off)


0V to 30V 0V to 10V 10V to 12V 12V to 30V

VO
Low Low Transition High

Pin Definitions
Pin #
1 2 3 4 5 6 7 8

Name
NC Anode Cathode NC VEE VO2 VO1 VCC Not Connected LED Anode LED Cathode Not Connected Negative Supply Voltage

Description

Output Voltage 2 (internally connected to VO1) Output Voltage 1 Positive Supply Voltage

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 2

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Safety and Insulation Ratings


As per IEC 60747-5-2. This optocoupler is suitable for safe electrical insulation only within the safety limit data. Compliance with the safety ratings shall be ensured by means of protective circuits.

Symbol

Parameter
Installation Classications per DIN VDE 0110/1.89 Table 1 For Rated Mains Voltage < 150Vrms For Rated Mains Voltage < 300Vrms For Rated Mains Voltage < 450Vrms For Rated Mains Voltage < 600Vrms For Rated Mains Voltage < 1000Vrms (Option T, TS) Climatic Classication Pollution Degree (DIN VDE 0110/1.89)

Min.

Typ.
IIV IIV IIII IIII IIII 40/100/21 2

Max.

Unit

CTI VPR

Comparative Tracking Index Input to Output Test Voltage, Method b, VIORM x 1.875 = VPR, 100% Production Test with tm = 1 sec., Partial Discharge < 5pC Input to Output Test Voltage, Method a, VIORM x 1.5 = VPR, Type and Sample Test with tm = 60 sec.,Partial Discharge < 5 pC

175 2651

2121

VIORM VIOTM

Max Working Insulation Voltage Highest Allowable Over Voltage External Creepage External Clearance External Clearance (for Option T or TS - 0.4 Lead Spacing) Insulation Thickness Safety Limit Values Maximum Values Allowed in the Event of a Failure

1,414 6000 8 7.4 10.16 0.5

Vpeak Vpeak mm mm mm mm

TCase IS,INPUT PS,OUTPUT RIO

Case Temperature Input Current Output Power (Duty Factor 2.7%) Insulation Resistance at TS, VIO = 500V

150 25 250 109

C mA mW

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 3

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Absolute Maximum Ratings (TA = 25C unless otherwise specied)


Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only.

Symbol
TSTG TOPR TJ TSOL IF(AVG) IF(PEAK) f VR IO(PEAK) VCC VEE VO(PEAK) tR(IN), tF(IN) PDI PDO Storage Temperature Operating Temperature Junction Temperature

Parameter

Value
-55 to +125 -40 to +100 -40 to +125 260 for 10sec 25

Units
C C C C mA A kHz V A V V ns mW mW

Lead Wave Solder Temperature (refer to page 21 for reow solder prole) Average Input Current Peak Transient Forward Operating Reverse Input Voltage Peak Output Current(1) TA 90C Peak Output Voltage Input Signal Rise and Fall Time Input Power Dissipation(2)(4) Dissipation(3)(4) Output Power Supply Voltage Current(10) Frequency(11)

1 50 5 3.0 0 to 35 0 to 30 0 to VCC 500 45 250

Recommended Operating Conditions


The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to absolute maximum ratings.

Symbol
TA VCC VEE IF(ON) VF(OFF) Power Supply Input Current (ON) Input Voltage (OFF)

Parameter
Ambient Operating Temperature

Value
-40 to +100 15 to 30 7 to 16 0 to 0.8

Units
C V mA V

Isolation Characteristics
Apply over all recommended conditions, typical value is measured at TA = 25C

Symbol
VISO RISO CISO

Parameter
Input-Output Isolation Voltage Isolation Resistance Isolation Capacitance

Conditions
TA = 25C, R.H.< 50%, t = 1.0min, II-O 10A, 50Hz(5)(6) VI-O = 500V(5) VI-O = 0V, Freq = 1.0MHz(5)

Min.
5000

Typ.

Max.

Units
VRMS

1011 1

pF

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 4

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Electrical Characteristics
Apply over all recommended conditions, typical value is measured at VCC = 30V, VEE = Ground, TA = 25C unless otherwise specied.

Symbol
VF

Parameter
Input Forward Voltage

Conditions
IF = 10mA

Min.
1.2

Typ.
1.5 -1.8

Max.
1.8

Units
V mV/C V

(VF / TA) Temperature Coefcient of Forward Voltage BVR CIN IOH IOL VOH VOL ICCH ICCL IFLH VFHL VUVLO+ VUVLO Input Reverse Breakdown Voltage Input Capacitance High Level Output Current(1) IR = 10A f = 1MHz, VF = 0V VO = VCC 3V VO = VCC 6V Low Level Output Current(1) VO = VEE + 3V VO = VEE + 6V High Level Output Voltage IF = 10mA, IO = -2.5A IF = 10mA, IO = -100mA Low Level Output Voltage IF = 0mA, IO = 2.5A IF = 0mA, IO = 100mA High Level Supply Current Low Level Supply Current Threshold Input Current Low to High Threshold Input Voltage High to Low Under Voltage Lockout Threshold VO = Open, IF = 7 to 16mA VO = Open, VF = 0 to 0.8V IO = 0mA, VO > 5V IO = 0mA, VO < 5V IF = 10mA, VO > 5V IF = 10mA, VO < 5V 0.8 11.5 10.0 -1 -2.0 1 2.0 VCC 6.25V VCC 0.25V 5

60 -2.0 -2.5 -2.5 2.0 2.5 2.5 VCC 2.5V VCC 0.1V VEE + 2.5V VEE + 0.1V 2.8 2.8 2.3 VEE + 6.25V VEE + 0.25V 3.8 3.8 5.0

pF A

mA mA mA V

12.7 11.2 1.5

13.5 12.0

V V V

UVLOHYS Under Voltage Lockout Threshold Hysteresis

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 5

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Switching Characteristics
Apply over all recommended conditions, typical value is measured at VCC = 30V, VEE = Ground, TA = 25C unless otherwise specied.

Symbol
tPHL tPLH PWD PDD (Skew) tr tf tUVLO ON tUVLO OFF | CMH | | CML |

Parameter

Conditions

Min.
150 150

Typ.
275 255 20

Max.
400 400 100 250

Units
ns ns ns ns

Propagation Delay Time to Logic IF = 7mA to 16mA, Low Output Rg = 10, Cg =10nF, Propagation Delay Time to Logic f = 10kHz, Duty Cycle = 50% High Output Pulse Width Distortion, | tPHL tPLH | Propagation Delay Difference Between Any Two Parts or Channels, (tPHL tPLH)(7) Output Rise Time (10% 90%) Output Fall Time (90% 10%) UVLO Turn On Delay UVLO Turn Off Delay Common Mode Transient Immunity at Output High Common Mode Transient Immunity at Output Low IF = 10mA , VO > 5V IF = 10mA , VO < 5V TA = 25C, VCC = 30V, IF = 7 to 16mA, VCM = 2000V(8) TA = 25C, VCC = 30V, VF = 0V, VCM = 2000V(9)

-250

60 60 1.6 0.4 35 35 50 50

ns ns s s kV/s kV/s

Notes: 1. Maximum pulse width = 10s, maximum duty cycle = 1.1% 2. Derate linearly above 87C, free air temperature at a rate of 0.77mW/C 3. No derating required across temperature range. 4. Functional operation under these conditions is not implied. Permanent damage may occur if the device is subjected to conditions outside these ratings. 5. Device is considered a two terminal device: Pins 2 and 3 are shorted together and Pins 5, 6, 7 and 8 are shorted together. 6. 5,000 VRMS for 1 minute duration is equivalent to 6,000 VACRMS for 1 second duration. 7. The difference between tPHL and tPLH between any two FOD3120 parts under same test conditions. 8. Common mode transient immunity at output high is the maximum tolerable negative dVcm/dt on the trailing edge of the common mode impulse signal, Vcm, to assure that the output will remain high (i.e. VO > 15.0V). 9. Common mode transient immunity at output low is the maximum tolerable positive dVcm/dt on the leading edge of the common pulse signal, Vcm, to assure that the output will remain low (i.e. VO < 1.0V). 10. Pulse Width, PW 1s, 300pps 11. Exponential Waveform, IO(PEAK) | 2.5A | ( 0.3s)

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 6

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Typical Performance Curves


Fig. 2 Output High Voltage Drop vs. Ambient Temperature
(VOH- VCC) - HIGH OUTPUT VOLTAGE DROP (V)

Fig. 1 Output High Voltage Drop vs. Output High Current


(VOH - VCC) - OUTPUT HIGH VOLTAGE DROP (V)
0.5 Frequency = 250Hz Duty C ycle = 0.1% IF = 7 to 16mA VC C = 1 5 to 30V VE E = 0V

0.00 VC C = 15V to 30V VEE = 0V IF = 7mA to 16mA IO = -100mA

0.0

-0.05

-0.5 TA = -40C

-0.10

-1.0

-0.15

-1.5

T A = 25C TA = 100 C

-0.20

-2.0

-2.5

-0.25

-3.0 0. 0

0.5

1.0

1.5

2.0

2.5

-0.30 -40 -20 0 20 40 60 80 100

IOH - OUTPUT HIGH CURRENT (A)

T A - AMBIENT TEMPERATURE ( C)

Fig. 3 Output High Current vs. Ambient Temperature


8 f = 200 Hz DUTY CYCLE = 0.2% IF = 7 to 16mA R g = 5 to GND 6
5

Fig. 4 Output High Current vs. Ambient Temperature


f = 10 0 Hz DUTY CYCLE = 0.5% IF = 7 t o 16mA R g = 10 to GND

IOH OUTPUT HIGH CURRENT (A)

I OH OUTPUT HIGH CURRENT (A)

VCC = 30V 4

VCC = 30V

2 VCC = 15V 1

VCC = 15V 2

0 -4 0

-2 0

20

40

60

80

10 0

0 -4 0

-20

20

40

60

80

100

TA AMBIENT TEMPERATURE ( C)

TA AMBIENT TEMPERATURE ( C)

Fig. 5 Output Low Voltage vs. Output Low Current


4
0.25

Fig. 6 Output Low Voltage vs. Ambient Temperature


V CC = 15V to 30V V EE = 0V VF(OFF) = -3V to 0.8V I O = 100mA

V OL - OUTPUT LOW VOLTAGE (V)

V OL - OUTPUT LOW VOLTAGE (V)

Frequency = 250Hz Duty Cycle = 99.9% V F( OFF) = -3.0V to 0.8V V CC = 15V to 30V V EE = 0V T A = 100C TA = 25C

0.20

0.15

0.10

TA = -40C

0.05

0 0.0

0.00

0.5

1.0

1.5

2.0

2.5

-40

-20

20

40

60

80

100

IO L - OUTPUT LOW CURRENT (A)

TA - AMBIENT TEMPERATURE ( C)

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 7

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Typical Performance Curves (Continued)


Fig. 7 Output Low Current vs. Ambient Temperature
8
5

Fig. 8 Output Low Current vs. Ambient Temperature


f = 10 0 Hz DUTY CYCLE = 99.5 % IF = 7 t o 16mA R g = 10 to VCC

IO L OUTPUT LOW CU RRENT (A)

R g = 5 to V CC 6 V CC = 30V

IOL OUTPUT LOW CURRENT (A)

f = 200 Hz D UTY CYCLE = 99.8% IF = 7 to 16mA

3 VCC = 30V 2

4 V CC = 15V 2

VCC = 15V 1

0 -40

0 -4 0

-20

20

40

60

80

100

-20

20

40

60

80

100

TA AMBIENT TEMPERATURE ( C)

T AMBIENT TEMPERATURE (C)

Fig. 9 Supply Current vs. Ambient Temperature


3.6 VCC = 30V VEE = 0V I F = 0m A (for I CCL) I F = 10mA (for ICCH)

Fig. 10 Supply Current vs. Supply Voltage


3.6 I F = 10mA (for ICCH) I F = 0m A (for I CCL) VEE = 0 , TA =25 C 3.2

3.4

ICC - SUPPLY CURR ENT (mA)

3.2

3.0 ICCH 2.8 I CCL 2.6

ICC - SUPPLY CURR ENT (mA)

2.8 I CCH I CCL 2.4

2.4

2.2 -40 -20 0 20 40 60 80 100

2.0

15

20

25

30

T A - AMBIENT TEMPEATURE ( C)

V - SUPPLY VOLTAGE (V)

IFLH - LOW TO HIGH CURRENT THRESHOLD (mA)

Fig. 11 Low to High Input Current Threshold vs. Ambient Temperature


4.0 V CC = 15V to 30V 3.5 V EE = 0V Output = Open

Fig. 12 Propagation Delay vs. Supply Voltage


400 IF = 10mA T A = 25 C Rg = 1 0 , Cg = 10 nF DUTY CYCLE = 50% f = 10 kHz

t - PROPAGATOIN DELAY (ns)

350

3.0

300 tP HL 250 tPLH 200

2.5

2.0

1.5

150

1.0 -40 -20 0 20 40 60 80 100

100 15

18

21

24

27

30

T A - AMBIENT TE MPERATURE ( C)

VC C SUPPLY VOLTAGE (V)

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 8

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Typical Performance Curves (Continued)


Fig. 13 Propagation Delay vs. LED Forward Current
500 500 VCC = 30 V, VEE = 0V Rg = 10 , Cg = 1 0nF T A = 25C DUTY CYCLE = 50% f = 10 kHz

Fig. 14 Propagation Delay vs. Ambient Temperature


IF = 10mA VCC = 30V , VEE = 0V Rg = 10 , Cg = 1 0nF DUTY CYCLE = 50% f = 10 kHz

t PROPOGATION DELAY (ns)

t PROPOGATION DELAY (ns)

400

400

300

300 tPH L tPLH 200

tPHL tPLH

200

100 6 8 10 12 14 16

100 -4 0

-2 0

20

40

60

80

1 00

I F FORWARD LED CURRENT (mA)

TA AMBIENT TEMPERATURE ( C)

Fig. 15 Propagation Delay vs. Sereies Load Resistance


500 IF = 10mA VCC = 30V , VEE = 0V
500

Fig. 16 Propagation Delay vs. Load Capacitance


IF = 10mA VCC = 30 V, VEE = 0V Rg = 10 T A = 25C 400 DUTY CYCLE = 50% f = 10 kHz

t PROPOGATION DELAY (ns)

400

300 tPHL tPLH 200

t PROPOGATION DELAY (ns)

Cg = 10nF T A = 25C DUTY CYCLE = 50% f = 10 kHz

300

tPHL tPLH

200

100 0 10 20 30 40 50

100 0 20 40 60 80 100

R g - SE RIES LO AD RESISTANCE ( )

C g - L OAD CA PACITA NCE (n F)

Fig. 17 Transfer Characteristics


35 T = 25C
A

Fig. 18 Input Forward Current vs. Forward Voltage


100

V 30

CC

= 30V

IF - F ORWARD CURRENT (mA)

10 TA = 100 C 1 TA = -40 C

V OU TPU T VOLTAGE (V)

25

20

15

0.1 TA = 25 C 0. 01

10

5
0.001

0 0 1 2 3 4 5

0.6

0.8

1.0

1.2

1.4

1.6

1.8

IF FOR WA RD LE D CURR EN T ( mA )

V F - FORWARD VOLTAGE (V)

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 9

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Typical Performance Curves (Continued)


Fig. 19 Under Voltage Lockout
14 (12.7 5, 12.80) 12 (11.25, 11.30)
VO OUT PUTVOLTAGE (V)

10

2 (11.20 , 0 .00) 0 0 5 10 15 20 (VC C - VEE) SU PPLY VOLTAGE (V) (12.70, 0.00)

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 10

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Test Circuit
Power Supply +
+ C1 0.1F

C2 47F

VCC = 15V to 30V

Pulse Generator
PW = 4.99ms Period = 5ms ROUT = 50

1
Pulse-In

2
R2 100 LED-IFmon

7
Iol

Power Supply +
D1
+ C3 0.1F

VOL
4
R1 100

C4 47F

V = 6V

To Scope

Test Conditions:
Frequency = 200Hz Duty Cycle = 99.8% VCC = 15V to 30V VEE = 0V VF(OFF) = -3.0V to 0.8V

Figure 20. IOL Test Circuit

Power Supply +
+ C1 0.1F

C2 47F

VCC = 15V to 30V

Pulse Generator
PW = 10s Period = 5ms ROUT = 50

1
Pulse-In

2
R2 100 LED-IFmon

7
Ioh
+ C3 0.1F

+
C4 47F

Power Supply
V = 6V

VOH
4
R1 100

D1 Current Probe

To Scope

Test Conditions:
Frequency = 200Hz Duty Cycle = 0.2% VCC = 15V to 30V VEE = 0V IF = 7mA to 16mA

Figure 21. IOH Test Circuit

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 11

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Test Circuit (Continued)

2
IF = 7 to 16mA

0.1F + VCC = 15 to 30V

VO 100mA

Figure 22. VOH Test Circuit

8
100mA

0.1F VO

VCC = 15 to 30V

Figure 23. VOL Test Circuit

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 12

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Test Circuit (Continued)


1 8

2
IF = 7 to 16mA

0.1F + VCC = 30V

VO

Figure 24. ICCH Test Circuit

2
+ VF = -0.3 to 0.8V

0.1F + VCC = 30V

VO

Figure 25. ICCL Test Circuit

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 13

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Test Circuit (Continued)

2
IF

0.1F + VCC = 15 to 30V

VO > 5V

Figure 26. IFLH Test Circuit

2
+ VF = 0.3 to 0.8V

0.1F + VCC = 15 to 30V

VO

Figure 27. VFHL Test Circuit

2
IF = 10mA

0.1F + 15V or 30V VCC Ramp

VO = 5V

Figure 28. UVLO Test Circuit

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 14

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Test Circuit (Continued)


1 8
0.1F

2
+ F = 10kHz DC = 50% Probe 50

VO Rg = 10 Cg = 10nF

VCC = 15 to 30V

IF tr tf 90% 50% VOUT tPLH tPHL 10%

Figure 29. tPHL, tPLH, tR and tF Test Circuit and Waveforms

IF A

2
B 5V +

0.1F + VCC = 30V

VO

+ VCM = 2,000V

VCM

0V

t VOH Switch at A: IF = 10mA

VO

VO Switch at B: IF = 0mA

VOL

Figure 30. CMR Test Circuit and Waveforms


2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0 www.fairchildsemi.com 15

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Package Dimensions
Through Hole
PIN 1 ID.
4 3 2 1
4 3 2 1

0.4" Lead Spacing (Option T)


PIN 1 ID.

0.270 (6.86) 0.250 (6.35)


5 6 7 8

0.270 (6.86) 0.250 (6.35)

0.390 (9.91) 0.370 (9.40)

SEATING PLANE

0.070 (1.78) 0.045 (1.14) 0.200 (5.08) MAX

0.156 (3.94) 0.144 (3.68)


SEATING PLANE

0.020 (0.51) MIN

0.390 (9.91) 0.370 (9.40) 0.156 (3.94) 0.070 (1.78) 0.144 (3.68) 0.045 (1.14) 0.020 (0.51) MIN

0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.016 (0.40) 0.008 (0.20) 15 MAX 0.300 (7.62) TYP

0.200 (5.08) MAX

0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.031 (0.78) 0.016 (0.40) 0.008 (0.20) 0 to 15 0.400 (10.16) TYP

Surface Mount 0.3" Lead Spacing (Option S)


0.390 (9.91) 0.370 (9.40)
4 3 2 1

8-Pin Surface Mount DIP Land Pattern (Option S)


0.070 (1.78)

PIN 1 ID.

0.270 (6.86) 0.250 (6.35)

0.060 (1.52)

0.100 (2.54) 0.295 (7.49) 0.415 (10.54) 0.030 (0.76)

0.156 (3.94) 0.144 (3.68)

0.070 (1.78) 0.045 (1.14) 0.020 (0.51) MIN

0.300 (7.62) TYP 0.016 (0.40) 0.008 (0.20)

0.200 (5.08) MAX

0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP

0.015 (0.40) MIN Both Sides

0.315 (8.00) MIN 0.405 (10.30) MAX.

Note: All dimensions are in inches (millimeters)

Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specications do not expand the terms of Fairchilds worldwide terms and conditions, specically the warranty therein, which covers Fairchild products.

Always visit Fairchild Semiconductors online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 16

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Package Dimensions (Continued)


Surface Mount 0.4" Lead Spacing (Option TS)
0.390 (9.91) 0.370 (9.40)
4 3 2 1

8-Pin Surface Mount DIP Land Pattern (Option TS)


0.070 (1.78)

PIN 1 ID.

0.270 (6.86) 0.250 (6.35)

0.060 (1.52)

0.100 (2.54) 0.392 (9.96) 0.511 (13.0) 0.030 (0.76)

0.156 (3.94) 0.144 (3.68)

0.070 (1.78) 0.045 (1.14) 0.020 (0.51) MIN

0.300 (7.62) TYP 0.016 (0.40) 0.008 (0.20) 0.015 (0.40) MIN Both Sides 0.400 (10.16) 0.497 (12.6) MAX.

0.200 (5.08) MAX

0.031 (0.775) 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP

Note: All dimensions are in inches (millimeters)

Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specications do not expand the terms of Fairchilds worldwide terms and conditions, specically the warranty therein, which covers Fairchild products.

Always visit Fairchild Semiconductors online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 17

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Ordering Information
Part Number
FOD3120 FOD3120S FOD3120SD FOD3120V FOD3120SV FOD3120SDV FOD3120T FOD3120TV FOD3120TS FOD3120TSV FOD3120TSR2 FOD3120TSR2V DIP 8-Pin SMT 8-Pin (Lead Bend) SMT 8-Pin (Lead Bend) DIP 8-Pin, IEC60747-5-2 option SMT 8-Pin (Lead Bend), IEC60747-5-2 option SMT 8-Pin (Lead Bend), IEC60747-5-2 option DIP 8-Pin, 0.4 Lead Spacing DIP 8-Pin, 0.4 Lead Spacing, IEC60747-5-2 option SMT 8-Pin, 0.4 Lead Spacing SMT 8-Pin, 0.4 Lead Spacing, IEC60747-5-2 option SMT 8-Pin, 0.4 Lead Spacing SMT 8-Pin, 0.4 Lead Spacing, IEC60747-5-2 option

Package

Packing Method
Tube (50 units per tube) Tube (50 units per tube) Tape and Reel (1,000 units per reel) Tube (50 units per tube) Tube (50 units per tube) Tape and Reel (1,000 units per reel) Tube (50 units per tube) Tube (50 units per tube) Tube (50 units per tube) Tube (50 units per tube) Tape and Reel (700 units per reel) Tape and Reel (700 units per reel)

Marking Information

3120 V XX YY B
3 4 5

2 6

Denitions
1 2 3 4 5 6 Fairchild logo Device number IEC60747-5-2 Option (only appears on component ordered with this option) (Pending approval) Two digit year code, e.g., 08 Two digit work week ranging from 01 to 53 Assembly package code

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 18

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Carrier Tape Specifications (Option SD)


D0 K0
t

P0

P2

A0 W1 B0

F W

User Direction of Feed

D1

Symbol
W t P0 D0 E F P2 P A0 B0 K0 W1 d R Pocket Pitch Tape Width

Description
Tape Thickness Sprocket Hole Pitch Sprocket Hole Diameter Sprocket Hole Location Pocket Location

Dimension in mm
16.0 0.3 0.30 0.05 4.0 0.1 1.55 0.05 1.75 0.10 7.5 0.1 2.0 0.1 12.0 0.1 10.30 0.20 10.30 0.20 4.90 0.20

Pocket Dimensions

Cover Tape Width Cover Tape Thickness Max. Component Rotation or Tilt Min. Bending Radius

13.2 0.2 0.1 max 10 30

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 19

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Carrier Tape Specifications (Option TSR2)


D0 K0
t

P0

P2

A0 W1 B0

F W

User Direction of Feed

D1

Symbol
W t P0 D0 E F P2 P A0 B0 K0 W1 d R Pocket Pitch Tape Width

Description
Tape Thickness Sprocket Hole Pitch Sprocket Hole Diameter Sprocket Hole Location Pocket Location

Dimension in mm
24.0 0.3 0.40 0.1 4.0 0.1 1.55 0.05 1.75 0.10 11.5 0.1 2.0 0.1 16.0 0.1 12.80 0.1 10.35 0.1 5.7 0.1

Pocket Dimensions

Cover Tape Width Cover Tape Thickness Max. Component Rotation or Tilt Min. Bending Radius

21.0 0.1 0.1 max 10 30

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 20

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

Reow Prole
260 240 TL 220 200 180 160 140 120 100 80 60 40 20 0 TP
Max. Ramp-up Rate = 3C/S Max. Ramp-down Rate = 6C/S

tP Tsmax Preheat Area Tsmin ts tL

Temperature (C)

120 Time 25C to Peak

240

360

Time (seconds)

Prole Freature
Temperature Min. (Tsmin) Temperature Max. (Tsmax) Time (tS) from (Tsmin to Tsmax) Ramp-up Rate (tL to tP) Liquidous Temperature (TL) Time (tL) Maintained Above (TL) Peak Body Package Temperature Time (tP) within 5C of 260C Ramp-down Rate (TP to TL) Time 25C to Peak Temperature

Pb-Free Assembly Prole


150C 200C 60120 seconds 3C/second max. 217C 60150 seconds 260C +0C / 5C 30 seconds 6C/second max. 8 minutes max.

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 21

FOD3120 High Noise Immunity, 2.5A Output Current, Gate Drive Optocoupler

TRADEMARKS The following includes registered and unregistered trademarks and service marks, owned by Fairchild Semiconductor and/or its global subsidiaries, and is not intended to be an exhaustive list of all such trademarks. Auto-SPM Build it Now CorePLUS CorePOWER CROSSVOLT CTL Current Transfer Logic EcoSPARK EfficentMax EZSWITCH* *

Fairchild Fairchild Semiconductor FACT Quiet Series FACT FAST FastvCore FETBench FlashWriter* FPS

F-PFS FRFET SM Global Power Resource Green FPS Green FPS e-Series Gmax GTO IntelliMAX ISOPLANAR MegaBuck MICROCOUPLER MicroFET MicroPak MillerDrive MotionMax Motion-SPM OPTOLOGIC OPTOPLANAR

PowerTrench PowerXS Programmable Active Droop QFET QS Quiet Series RapidConfigure Saving our world, 1mW/W/kW at a time SmartMax SMART START SPM STEALTH SuperFET SuperSOT-3 SuperSOT-6 SuperSOT-8 SupreMOS SyncFET Sync-Lock *

The Power Franchise

TinyBoost TinyBuck TinyLogic TINYOPTO TinyPower TinyPWM TinyWire TriFault Detect TRUECURRENT* SerDes UHC Ultra FRFET UniFET VCX VisualMax XS

PDP SPM Power-SPM

* Trademarks of System General Corporation, used under license by Fairchild Semiconductor. DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION, OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. THESE SPECIFICATIONS DO NOT EXPAND THE TERMS OF FAIRCHILDS WORLDWIDE TERMS AND CONDITIONS, SPECIFICALLY THE WARRANTY THEREIN, WHICH COVERS THESE PRODUCTS. LIFE SUPPORT POLICY FAIRCHILDS PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.

ANTI-COUNTERFEITING POLICY Fairchild Semiconductor Corporation's Anti-Counterfeiting Policy. Fairchild's Anti-Counterfeiting Policy is also stated on our external website, www.fairchildsemi.com, under Sales Support. Counterfeiting of semiconductor parts is a growing problem in the industry. All manufacturers of semiconductor products are experiencing counterfeiting of their parts. Customers who inadvertently purchase counterfeit parts experience many problems such as loss of brand reputation, substandard performance, failed applications, and increased cost of production and manufacturing delays. Fairchild is taking strong measures to protect ourselves and our customers from the proliferation of counterfeit parts. Fairchild strongly encourages customers to purchase Fairchild parts either directly from Fairchild or from Authorized Fairchild Distributors who are listed by country on our web page cited above. Products customers buy either from Fairchild directly or from Authorized Fairchild Distributors are genuine parts, have full traceability, meet Fairchild's quality standards for handling and storage and provide access to Fairchild's full range of up-to-date technical and product information. Fairchild and our Authorized Distributors will stand behind all warranties and will appropriately address any warranty issues that may arise. Fairchild will not provide any warranty coverage or other assistance for parts bought from Unauthorized Sources. Fairchild is committed to combat this global problem and encourage our customers to do their part in stopping this practice by buying direct or from authorized distributors. PRODUCT STATUS DEFINITIONS Definition of Terms Datasheet Identification Advance Information Preliminary No Identification Needed Obsolete Product Status Formative / In Design First Production Full Production Not In Production Definition Datasheet contains the design specifications for product development. Specifications may change in any manner without notice. Datasheet contains preliminary data; supplementary data will be published at a later date. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve design. Datasheet contains final specifications. Fairchild Semiconductor reserves the right to make changes at any time without notice to improve the design. Datasheet contains specifications on a product that is discontinued by Fairchild Semiconductor. The datasheet is for reference information only.
Rev. I40

2003 Fairchild Semiconductor Corporation FOD3120 Rev. 1.17.0

www.fairchildsemi.com 22

You might also like