You are on page 1of 35

DESIGN AND ANALYSIS OF MULTI-STORIED BUILDING

By :
K.Uday kumar(09245A0103) K.Nagendra babu(08241A0123) Md.Khaja taqiuddin(08241A0117)

CONTENTS
1. 2. 3. 4. 5. 6. 7.

INTRODUCTION CODES STATEMENT OF THE PROJECT LOADS ON THE STRUCTURE OBJECTIVE OF STRUCTURAL DESIGN DESIGN AND ANALYSIS REFERENCES

INTRODUCTION
project is based on the design and analysis of the multi-storied building.
Analysis Notation Our

is done through using the STAAD-PRO.

adopted through out the project is same as in IS-456-2000.

CODES
z IS-456:2000

:DESIGN CODE FOR RCC STRUCTURES :CODE FOR DEAD LOADS :CODE FOR IMPOSED LOADS :CODE FOR WIND LOADS

z IS-875(PART1) z IS-875(PART2) z IS-875(PART3)

STATEMENT OF THE PROJECT :

1.Utility of building : Residential buildng z 2. No of storeys : G+5 z 3.Shape of the building: Rectangular z 4.No.of staircases : 6 nos z 5.Type of walls : Brick wall
z

Geometric details : Ground Floor : 9.0 MFloorFloor Height : 3.0 M Height of Plinth: 0.6 M above G.L Depth of Foundation:2 M below G.L

Material details : Concrete Grade : M25 Grade of steel : HYSD REINFORCEMENT of Grade Fe415 Bearing Capacity of Soil : 200 KN/M2 Type Of Construction : R.C.C framed structure

DIFFERENT TYPES OF LOADS ON THE STRUCTURE


zDead

loads zImposed loads zWind loads

Dead loads
zInvolves

selfweight of zRCC slab zBeams & columns zPlinth zWalls

Imposed loads
zImposed

also known live loads zLoad over the floor i.e. load of persons it is calculated as 0.2 kN/m2 zThis load is applied over the length of structure

Wind loads
z Wind z Wind

is air in motion

loads are calculated according to IS:875(part 3) of wind and exposure are applied in the directions as required

z Intensity

TYPES OF LOADS IMAGE VIEW

Load combinations
zThe

structure should be analysed for combination of loads as in practice we have number of loads in various directions act zSome of the combinations to be checked are z1.5(DL+LL) z1.5(DL+WL)

OBJECTIVES OF STRUCURAL DEIGN


Structure designed should satisfy the criteration of ultimate strength. Structure should satisfy the servicablity It should satisfy the stablity against overturning , sliding , and buckling.

The main objective of the design are


z Foundation

design z Column design z Beam design z Slab design

DESIGN PRINCIPLE, ASSUMPTION AND NOTATION ASSUMED


z

The notation adopted throughtout the work is same as in IS 456-2000 ASSUMPTION IN DESIGN Using partial safety factors for loads in accordance with clause 36.4 of IS 456-2000 Partial safety factor for material in accordance with clause 36.4.2 IS 456-2000 is taken as 1.5 for concrete and 1.15 for steel Using partial safety factors in accordance with clause 36.4 of IS 456-2000 combination of load (D.L +L.L) 1.5 (D.L +L.L +W.L) 1.2

Density of materials used MATERIAL i) Plain concrete ii) Reinforced iii) Flooring material (c.m) iv) Brick masonry v) Fly ash

Density 24.0 KN/m3 25.0 KN/m3 20.0KN/m3 19.0KN/m3 5.0KN/m3 3.0KN/m2 3.0KN/m2 3.0KN/m2

LIVELOADS: In accordance with IS 875-86 i) Live load on slabs = ii) Live load on passage = iii Live load on stairs =

Structural design
For slabs,Depth is 130 mm provided & min depth is 90mm Factored Load on slab is 12Kn/m For beams,after calculations are done.the Dimensions of beam is 230*350mm Factored load on beam is 15.87Kn/m

Shape of column is Rectangular z For columns, the dimension of column is 230*500mm z Factored load on column 1090.10KN
z

For footings, the bering capacity of soil is 200Kn/m2 z To provide the dimension of footing is 1.5m*2.7m

ANALYSIS
z Analysis

is done using STAAD PRO developed by BENTLEY z Once the loads and load combinations are assigned to the structure, analysis is to be done z Analysis is done for RCC structure

Assign the properties of structure

ASSIGN LOADS ON THE SLAB

Load assign on the walls

Assign wind load on the structure

RCC analysis
z

Code is assigned as IS:456-2000 The parameters are assigned to the structure Commands to be given are
z z

z z

concrete design Member takeoff

Conclusions
Staad pro become more and more critical in the analysis of engineering & scientific problems z This facilities for the implementations of more effective & professional engineering software z It should be affordable to promote their wide spread usage amongst civil engg at a global scale
z

REFERENCES
z Structural

analysis by S.RAMAMRUTHAM CODE used

z IS456-2000 z AUTO

CAD & STAAD PRO packages of RCC structures by B.C PUNMIA

z Design

Thank you!

You might also like