Professional Documents
Culture Documents
T S14"- 2 1 "
CONTENTS
SAFETY INSTRUCTION AND GENERAL INSTRUCTION1 ALIGNMENT ITEMS AND PROCEDURE.2 TEST EQUIPMENT 3 DEBUGGING INSTRUCTION..3 IC BLOCK DIAGRAM .. 9 WIRING DIAGRAM..13 SCHEMATIC DIAGRAM . 1 4 APPENDIX: EXPLODED VIEW
AUTION: THIS SERVICE MANUAL IS ONLY FOR PROFESSIONAL SERVICE PERSONNELS REFERENCE. BEFORE SERVICING THIS CHASSIS, PLEASE READ THE FOLLOWING NOTICE ITEMS. 1. SAFETY INSTRUCTION AND GENERAL INSTRUCTION Before servicing and aligning this equipment, please read the following X-RAY RADIATION PRECAUTION ,SAFETY PRECAUTION and PRODUCT SAFETY NOTICE. 1.1 X-RAY RADIATION PRECAUTION 1 Excessive high voltage can produce potentially hazardous X-RAY RADIATION. To avoid such hazards, the high voltage must not be above the specified limit. The normal value of the high voltage of this receiver is under 24.5kV(21) and 22.5KV(14) at zero beam current (minimum brightness), the high voltage must not, under any circumstances, exceed 30kV. 2 Each time a receiver requires servicing, the high voltage should be checked following the HIGH VOLTAGE CHECK procedure in this manual. It is recommended the reading of the high voltage be recorded as a part of service record. It is important to use an accurate and reliable high voltage meter. 3 The primary source of X-RAY RADIATION in this TV receiver is the picture tube. For continuous X-RAY RADIATION protection, the replacement tube must be exactly the same type tube as specified in the parts list. 4 Some parts in this receiver have special safety-related characteristics for X-RAY RADIATION protection. For continuous safety, parts replacement should be undertaken only after referring to the PRODUCT SAFETY NOTICE below. 1.2 SAFETY PRECAUTION WARNING: Service should not be attempted by anyone unfamiliar with the necessary precaution on this receiver. The following are the necessary precautions to be observed before servicing this chassis. 1) Since the power supply circuit of this receiver is directly connected to the AC power line, an isolation transformer should be used during any dynamic service to avoid possible shock hazard. 2) Always discharge the picture tube anode to the CRT conductive coating before handling the picture tube. The picture tube is highly evacuated and if broken, glass fragments will be violently expelled. Use shatter proof goggles and keep picture tube away from the unprotected body while handling. 3) When replacing a chassis in the cabinet, always be certain that all the protective devices are put back in place, such as: non-metallic control knobs, insulating covers, shields, isolation resistor-capacitor network etc. 4) When replacing parts or circuit boards, disconnect the power cord. 5) When replacing a high wattage resistor (oxiode metal film resistor) on the circuit board, keep the resistor 10mm (1/2in) away from circuit board. 6) Connection wires must be kept away from components with high voltage or high temperature. 7) If any fuse in this TV receiver is blown, replace it with the FUSE specified in the chassis parts list.
1
1.3
Many electrical and mechanical parts in the chassis have special safety-related characteristics. These characteristics are often passed unnoticed by a visual inspection and the X-RAY RADIATION protection afforded by them cannot necessarily be obtained by using replacement components rated for higher wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual and its supplement electrical components having such features are shaded on the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts which do not have the same characteristics as specified in the parts list may create shock, fire, X-RAY RADIATION or other hazards. 2 Alignment items and procedure The alignment flow chart (see below figure). EEPROM copy
B+ check
High-handed Field breadth and field line VG2 adjust Filament voltage X-radial protect White balance and sub-bright RF AGC adjust H-field and center field and field breadth Picture and audio Sub-brightness White balance OSD center position
Color pure and assemble AV (S.DVD)
Audio check
Foucs fine adjust The button check Leave factory state setup Remote control check Assemble check check Safety check
3 TEST EQUIPMENT
3.1 3.2 3.3 3.4 3.5 3.6 AUDIO VOLTAMETER OSCILLOGRAPH HIGH-VOLTAMETER DIGITAL MULTIMETER AC ATTACK PULL TEST EQUIPMENT SCAN frequency signal generator BT-3
4 Debugging instruction
enter into the factory debugging menu use to the remote control(RC-A23),follow to the blow model enter into the factory: DISPLAY MUTE MUTE MUTE enter into the factory press sleep button for pages upward, press return button for pages downward, press CH+/- to select alignment items and VOL+/- to adjust volume, press MUTE to exit. If the remote sensor designed for alignment is unavailable, press the following buttons to enter by using user remote sensor 4.2 B+ voltage adjustment Check B+ voltage ( negative pole of VD509) by using DC voltmeter DC 200V 14110 V1 V CRT 21PF 100 V CRT A15QDX992X002(H) 21110 V1 V CRT 54SX503Y22-CD01 A51LVV898X12 4.1
4.3
AGC adjustment Measure the voltage of RF AGC by connecting digital DC voltmeter with TP1, receive weak signal (40dBu) and the static AGC voltage of TP1 AGC should be V1=4V0.2V; the receive medium signal (60dBu), adjust the value of PAGE8 RF. AGC of factory menu and the start-control voltage of TP1 AGC should be V2=3.5V0.2.if V2>3.5V, then the voltage is -1 or -2,if V2<3.5V, then the voltage is+1 or+2. after adjustment the picture should not appear no-sync , distortion and moire. White balance and screen-grid voltage VG2 adjustment After enter PAGE3 of factory menu, use remote sensor directly to adjust white balance by pressing the following digital buttons: 1=R.BIAS(+) 2=G.BIAS(+) 3=B.BIAS(+) 4=R.BIAS(-) 5=G.BIAS(-) 6=B.BIAS(-) press pp button to select picture modeT1T2brightsoftnatureuser the current picture mode will be display on the screen. The T1 mode has the maximum value of brightness and contrast with all the other items min. Value of all the analog are minimum while in T2 mode. Before adjustment you should set the following items :SUB-BRIGHT=50, R.B=100, G.B=100, B.B=100, R.D=100, G.D=15, B.D=100 Adjustment method: 1. press PP button to select T2 picture mode, press CH+/- to select V.K, press vol+ to let the field scanning fail to oscillate, adjust the screen-grid potentiometer on FBT clockwise to let horizontal bright line just appear on the screen; let the value of G.B unchanged, adjust R-BIAS and B-BIAS to let the horizontal bright line appear white. If the green horizontal line dont appear firstly, fine-turn the screen-grid voltage, the adjust R.B and B.B until red , green and blue just appear. After adjustment press VOL- to obtain normal field scanning mode. 4.4 Receive grey-scale signal (D8), enter PAGE4 of factory menu, press PP to select T2 picture mode,
3
adjustment SUB-BRIGHT to let picture on the screen microbright. 4.5 receive white balance adjustment signal enter PAGE3 of factory menu, press PP to select T1 picture mode, let the value of GD unchange, adjust RD and B.D to let the white part of the picture appear white. 4.6 Use white balancer to rectify the white balance under following conditions colour temperature:12000K+8MPCD x =0.270 0.008 Y=0.2830.008 dark space : 4.5nit, bright space: 60nit Note:1. Check the white balance of bright field and dark field by receiving monochrome signal or adjusting the degree of saturation to minimum under maintenance condition, adjust RGB BIAS in dark field and RGB DRIVE in bright area, adjust bright/dark balance repeatedly until the bright and dark field have no colour drift. 2. While the colour saturation changed from maximum to minimum, if the dark balance appears changeable, adjust RY.DC.LVL and BY.DC.LVL (page3) to let it coincide with white balance. 3. If the dark balance appears changeable while connected with DVD, adjust YUV.BY.DC and YUV.RY.DC (PAGE4) to let it conincide with white balance. 4.7 High voltage and filament voltage check Connect a high-voltage meter between anode cap of picture tube and the ground, measure the filament voltage using rms voltmeter, set the picture mode to standard, the high-voltage: 24.5KV1KV of 21, 22.5KV1KV of 14,filament voltage: 6.30.1Vrms. 4.8 x -ray protection check Receive local TV signal, set the picture mode to standard, shorten the circuit and measure the value of TP1-TP2, restart the TV 30 seconds after turn off the power source and it should return to normal. 4.9 AV function check according to the owners manual require, connect to the AV equipment and the AV interface: VIDEO IN: 1 Vp-p 75OHM AUDIO IN: (-83)dBm>47 kOHM S interface Y IN: 1 Vp-p 75OHM C IN: 0.3 Vp-p 75OHM DVD Y IN: 1 Vp-p 75OHM Cr IN: 0.7 Vp-p 75OHM Cb IN: 0.7 Vp-p 75OHM AV parts check incept to standard the TV signal:
4.10
a AV and crossfire and allophone and shake ; b The user control function ana picture model c The remote control function check; d Color pure and converge check. 4.11 leave factory state setup Picture model (PP) STENDARD language All the country language Color system AUTO C.CAPTION C1 CCD ON MUTE OFF RECEPTION AIR AFT ON
4
MTS PASSWORD Volume 4.12 P1-60 V SIZE V SHIFT H-PHASE V LINE V SC V COMP L.BLK R.BLK P3-50 V SIZE V SHIFT H-PHASE V LINE V SC P5 LINE RB GB BB RD GD BD P6 RF AGC SUB-BRI SUB-CNT SUB-COL SUB-SHP SUB-TINT P7 VOL.FIL OSD.COT OSD.HPOS AFT VIF SW
the factory menu adjustment model pre-set OSD item 60HZ field amplitude 60HZ field center 60HZ H-center 60HZ V-line 60HZ field S-correct field amplitude compensate Left blanking Right blanking 50HZ field amplitude 50HZ field center 50HZ H-center 50HZ V-line 50HZ field S-correct Level bright line Red cut off Green cut off Blue cut off Red driver Green driver Blue driver RF AGC Sub-brightness Sub-contrast Sub-colour Sub-definition Sub-tint Volume control ADC filter OSD contrast OSD center Line AFC loop gain and sync gate switch IF3=45.75MHZ
5
model 4.5.1 4.5.1 4.5.1 4.5.1 4.5.1 fixed fixed fixed 4.5.2 4.5.2 4.5.2 4.5.2 4.5.2 0=normal 1= Level bright line 4.4 4.4 4.4 4.4 4.4 4.4 4.3 4.4 fixed fixed fixed fixed fixed fixed fixed fixed fixed
OSD SIF SW VIDEO LEVEL P8 GY ANGLE V.R TM R/B ANG R/B BAL C TRAP H FREQ C.BPF TEST P9 OVER.MOD.SW OVER.MOD.LVL BLK.STR BLK.GAIN Y.APF PRE.ADJ OVER ADJ C.VCO.ADJ P10 BRT.ABL.DEF MID.STP.DEF BRT.ABL.THR WPL.OPE V BLK.SW FBP BLK SW DC REST CD.MODE P11 CORE GAIN .GAMA RGB TEMP.SW A.MONI SW SVO OR FSC CROSS B/W
item Sound IF0=4.5MHZ VIDEO LEVEL G-Y demodulation angle Filed scan strting time R-Y/B-Y demodulation angle R-Y/B-Ydemodulation balance Color trap filter H-frequency Color band filter center frequency Selection over-modulation function Adjustment over-modulation working point Dark level expand starting control point Dark level expand gain Selection color trap filter Pre-shoot overshoot Color VCO frequency adjustment Brightness ABL ABL start control point ABL threshold White peak limit Field blanking switch Horizontal blanking switch DC recover rate Field frequency division model Noise reduction r-correct RGB DC output temperature speciality Selection pin5 output Selection pin5 output Selection test signal
6
Pre-set 0 3 0 0 8 8 6 16 0
model fixed fixed fixed fixed Fixed fixed fixed fixed fixed
0 0 0 0 0 3 3 4
Fixed,0=nothing 1=have fixed Fixed,0=40IRE 2=60IRE 3-OFF Fixed,0=MIN 2=MAX 0=trap filter,1= direct pass(YcbCr&Y/C) fixed, 0=narrow 3=width Fixed,a 0=narrow 3=width fixed,0-4-7=-120KHZ-0-90KHZ
0 0 7 2 0 1 1 0 2 0 1 1 0 0
fixed,0=ABL ON 1=ABL OFF fixed fixed fixed fixed ,0=nomarl;1=width model fixed,0=inside produce;1=FBP and inside logic and fixed,0=100% 1=107% fixed,0=auto fixed,0=OFF 1=MIN 3=MAX fixed,0=OFF fixed Fixed, 1=SAO
fixed,0=VIDEO 1=FSC(color sub-carrier wave)
fixed,0=TV
OSD CRAY.MODE P12 BY TV RY TV BY YUV RY YUV S.TRAP.TEST LOW.BRI LOW.CONT P13 COL.KILL VCO.FREQ P14 Y GAIN Y TH B OFFSET B WIDTH C OFFSET C WIDTH CAN.V CHIP OPTION AV MTS V.OFF.MOTE PWR.MEM 1115 BLCK GROND N/PN 1115(the unit no use) VOL.OFFSET GAIN PWM LOGIC AVL MODE AVL DET LEVEL AVL SLOPE PWM SET
Pre-set 0
model fixed,0=white(75%)1=grey(15%) 4.4 adjustment dark white balance(TV/AV model) 4.4 adjustment dark white balance(TV/AV model) 4.4 adjustment dark white balance (DVD input) 4.4 adjustment dark white balance(DVD input) fixed fixed fixed fixed,0=-30dB 3=-40dB fixed fixed fixed fixed fixed fixed fixed 1=CAN.V-CHIP AV input select(3=AV1/AV2/S/DVD) 0=nothing,1=72700 2=AN5832 0=discharge,1=close 0=standby,1=auto turn on,2=memory fixed,0=nothing;1=have 0=nothing 1/3=blue background;2=black background 0=South America;1=North America
Blue chromatism DC level Red chromatism DC level DVD input Blue chromatism DC level DVD input Red chromatism DC level Sound trap filter adjustment Min-brightness Min-contrast Achromatic level VCO frequency
8 8 8 8 6 28 30 5 32 0 0 0 0 0 0
V-CHIP AV selection MTS IC selection Turn off model Turn on model select LV1115 No signal background selection South America and North America selection
OSD VOL 1 VOL 25 VOL 50 VOL 75 72700 ALC VOL SAP LEVEL SIF.M/BB.M 5832 AGC
item 1% volume control speciality 25%volume control speciality 50%volume control speciality 75%volume control speciality ALC Baseband model ,input level adjustment SAP level SIF and baseband model
Pre-set 30 32 68 82 1 0 1 0 1
model fixed fixed fixed fixed fixed ,1=ALC ON The unit no use fixed fixed,0=SIF MODE 1=BB MODE fixed
Note: above / are the adjustment data for North America, below it are for South America.
23 24 25 26 27 28 29
5.00
42 41 40
CPU GND PLL reset Button input TV/AV H=TV L=AV AV1/AV2 MUTE high level
10
4.90 0 5
39 38 37 36
30 31 32
0 5.00 5.00
35 34 33
VDD x T2 x T1
KA5Q0765RT
5.65
AN7522
function power
CH1+ output
pin
7 8 9 10 11 12
GND
CH1- output
LA78040 Pins function pin 1 2 3 4 function Inverting input VCC Pump up output GND pin 5 6 7 function Ver. output Output stage vcc NON inverting input
12
DEGASSINGP COIL
220V/50HZ
XS901 XS902
BOARDP667-TS2130-05
KEY
+ -
+ -
POWER SWITCH
SPEAKER
A1 A2 XS202
XS501
FOCUS
XS203
WIRING DIAGRAM
S501
XS502
CRT PCB
XS402
MAIN BOARDP667-TSC30-01
XS201
N201
CRT
XS604
XS301
XS302
S PORT XS602
XS601 AV PORT
TUNER
XS606
667-TS2130-29
AV BOARD
13
*
3 4 5 6 7 8
IN Y
OUT1(+) OUT2(+)
AGC
AS
SCL
SDA
BP
IF1
Cb
Cr
R L
OUT L V
AN7522
N701
BT/LOCK
11
R621 75 R601
75 10u 10u 10u 10u 220u 1 2200u/16V
C602 C603
IN4148
XS701
1 R+
R605 1K
R606 1K
R607 1K
1u/16V 10n 2
C706
1u/16V 10n
C707
C708 C709
C401 100p
R CRT
B
12
2W
R413 15K
9V
R108 100
1 2 3 4 5 10u
2W
R104
R102 10K
2W 12K
R103 100
TO SPEAKER
C104 4u7
C105
2 1
0.01u
VD101
R610 4.3K
D SCL 1N4148
L102
R704 VD702
C1815 2.2u 16V
R105 5K6 C106 0.01 C607 V702 C704 R711 C710 R712 R713 C705
5
R416 2.7K
D
V101 C2717
G V1 G R1 L1
R404 100
B
RD30E
C108 0.01
SCL1 SDA1
R106 1K2
R109 27
SCL1
SDA1
S-Y V1
Y-DVD
R1
L1
RO
LO
S-C
V OUT
LO RO
JUMPERB
FM
G CRT
L1
R1
S-C
S-Y
KEY
V OUT
5V-2
9V
CRT R
R615 100K
R614 100K
R612 1K C609
C610 10u
R421 330
C405 390p
VD402 IN4148
R406 390
V1
5
R239
C403 100p
Y-DVD
VD901 LED
11 6
AV1/AV2
R616
10 7
B CRT
14
R407 100
V403 2SC2688
B
2W
L2 G R2 G V2 G
R418 2.7K
E
5V-1
15K
R913 47 R228 100 C243 50V 1u C235 0.47 R237 47K R238 47K R234 1K C238 50V 2.2u C248 50V 1u C229 18p C226 47pF C245 C220 0.1 15p
16V 1u 7.5K
R410 1K2
R422 330
R409 390
N901 R247 2M2 R209 750 L204 68uH VD203 5C1 VD204 HZ5C1
1
REM
C228 0.1 G202 C219 0.01uF C244 0.01 10V 100u VD202 5C1 R221 10k * R222 390K C230 0.1 * R225 47K G201
1 2 3 4 5 6
HRM3806B
PIN4 0.01
Z201 *
C253
XS201
XS401
1 C 2 R CRT 3G
62
464
563
CRT B
R912 2K
XS901
XS202
FBP
XS604
CRT G
R618 100K
VD403 IN4148
R G B
CRT
4 B CRT 5 6
CR 51
CB 49
PLL 41
XT2 34
XT1 33
C G G CRT 3 2
V IN 56
AV IN 54
C APC 53
4.43M 50
V OUT 60
Y(Y/C) 46
C(Y/C)45
FBP IN 44
RESET 40
VDD 35
IF GND 62 C237
Y(DVD) 48
AFT FIL 59
PIF IN 1 64
PIF IN 2 63
B L D FIL 57
CCD VCC 43
CPU GND 42
V/C/D VCC 55
V OUT/FSC 52
PO4/MUTE 36
RF AGC 61
APC FIL 58
C902 33u
DDS FIL47
XS902
XS203
VD705 IN4148
R R CRT B B CRT
PO5/AV1\AV2 37
*
8 HV
SW901
VOL-
KEY
N201 LA76931
N201 LA76931
* * * * * * * * * * * * * * * * *
XS403 CRT
4
SW902
R902 1K
PIN3
N301 LA78040
INV IN
VCC
PUMP
GND
OUTPUT
OUT VCC
3 SIF IN
5 FM/A OUT
6 A OUT
8 IF VCC
1 SIF OUT
2 PIF AGC
4 FM FIL
9 A IN
10 ABL
28 P15 POW
29 P17 STB
30
31 P12/SDA1
11 RGB VCC
12 R OUT
13 G OUT
14 B OUT
15 AKB
16 V RAMPOSC
17 V OUT
18 VCO IREF
22 GND
23 P00 X-RAY
24 PO1/INT1
PO3/INT3 26 REM
19 H VCC
20 H AFC
21 H OUT
27 P14
32 P13/SCL1
CH-
R904 3K3
NON IN
SW903
VOL+
R903 2K2
R226 10K
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
CH+ C246
R905 4K7
9
R206 10K
R318 1K5
68K
SDA131
SW905
R213
4K7 R210
R242
MENU R208 51 C241 0.01 C240 0.01 R211 C218 220 VD201 10V 100u HZ5C2 10V 100u R204 10K R203 330
B
1/4W 5K1
SCL132
C201 39pF
0.1
C250
C252 200pf
R235 100
C327 10u 16V R330 5K6 C333 1000 R327 12K VD308 IN4002 C332 100U 35V R325 10K R328 33K C331 10p R321 1 1/2W R326 330 C329 2200u 25V
1W
XS402 PIN4
SW906 C206 0.022 C211 22u 16V C212 10V 100u C215 0.47u R216 4K7 R218 100
R907 12K
C204 1u C202 C203 0.022 39pF R201 39K C209 L203 C210 100u 68uH 0.01
10
6
AV/TV
L201 22uH
SW907
E C
R908 33K
R202 1K
SCL1
POWER
5V-2 9V
R316 1W 1K
1W
FM
R909 150K R217 4K7 R207 390K R243 10K R219 100
REM
N202 24C08
X-RAY
POWER OFF MUTE
RL01
R523
4 3 2 1
10K
VD506 1N4148
V503
V501 1015 R522 3K9 C522 *
C
C1815
C529
R528 6K8 XS205 V504 C1815 R524 6K8
B C
10u/16V
NPN2
R518
C515 680
1 B 1W
10K
BUS DEBUG
1
GND 1
10
VD507 FR103
C E 75uH
8 *
15 1W C521 470u 16V
L503
E
POWER
OFF ON
VD501 VD501
1
2 1
L502 L502
RT501 HZ6B1
1
C502 0.1
PTC
6
C
C306 390p
R303 33
3
7 6 * VD513
* 9 13
14V
C519
C526 0.1
R502 4.5
VD508 FR103
1000u 25V
C506 4n7
* 12 16
C518 103p C514 1n 1KV
L501
1
N501 HZ6B1
KA5Q0565RT
VD504 FR103
R507 10
1
VD514
B+
C527 10n R512 30K R513 180K
C 1 B
3W
XS501
1 3 2 E
C501 0.1 R508 1K R517 5K6 R511 4K7 1/4W R516 5K1 1/4W N504 TL431 VD510 TBY56J
2
R506 680
* 15
R301 9K1 2W
1W
* 3
C517 100u 160V
1W
R529
1W-1K
R501 2.2M
1500pF 1KV
C508
4 N502
VD511 RP501
1K
HZ2C2
C516
R509 8M2
R343 150K
R344 68K
47u 50V
ABL
3 4 5 6 7
4 3 2 1
5 6 7 8
A OUT
JUMPERC
A IN
SDA1
V201 2SA1815
A0 A1 A2 GND
TP1
1 B
TP2TP2 TP1TP1
V303 C1815Y R313 4K7 * C325 100u 16V
B
L302 R309 10 R311 8K2 R312 4K3 C319 470u 16V N302
3 12V
L303
T301
3 5
HV
TP9 9V
7809
C322 470u 16V
C320 10n
24V
C317 1000u 35V TP6
27V
VD305 C315 FR103 680p C316 10n VD304 FR103 7 R304 10 1W C307 160V 4u7 R302 2K7 R332 3K3 3W C310 3n3
4 2 1
4 2
R306 1W 2.4 *
9 10
FOCUS SCREEN
C311 5n6 C312 (390) C309 470 2KV * C313 (390)
6
C339 400V 0.33 L301 L2 XS302 R305 1k VD313 S5295G VD301 S5295J C301 33u 160V C338 250V 4u7 C303 33u 250V C302 220p C304 56n 200V
4 3 A
200V B+
2 1
Title Size D Date: File: 6-Dec-2004 E:\PROTEL\LHL.Ddb 8 Sheet of Drawn By: Number Revision
N0. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
DESCRIPTION
NO. 16 17 18 19 20 21 22 23 24 25
DESCRIPTION
SCREW CRT BOARD CRT SCREW CRT FIXER LED COLUMN POWER SWITCH SCREW SPEAKER FRONT CABINET Standby BUTTON SPEAKER LOGO SIDE AV BUTTON ASSEMBLY
MAIN BOARD ASSEMBLY REAR PANEL THREAD CLASP SCREW BRAIDED PULLING SPRING DEGAUSSING COIL LINE CLASP BRAIDED PULLING BACK CABINET LABEL
PART LIST OF EXPLODED VIEW (X2181) NO. PART NO. DESCRIPTION 1 FRONT CABINET 2 SPEAK ASS'Y 3 360-30028-00 POWER SWITCH 4 870-20846-00 RIGHT guid track 5 MAIN PCB ASS'Y 6 780-C80XH-120 BACK CABINET 7 CRT 8 870-20845-00 LEFT guid track 9 POWER BUTTON BOARD ASS'Y 10 KEY BOARD ASS'Y 11 742-30060-00 POWER CORD BLOCK 12 868-20314-00 CRT BLOCK
603-TS13330-16 Ver.1.0