You are on page 1of 36

End-to-End Embedded Power

2012 Product Selection Guide

End-to-End Power Solutions

Hybrid Architecture:
85% overall efficiency

Front Ends & Rectifiers


WEAKNESSES:

STRENGTHS:

48 or 24V RECTIFICATION 48 or 24V RECTIFICATION OPTIONAL BATTERIES OPTIONAL BATTERIES

Large installed base di/dt of isolated bricks less than POLs Supports SELV systems Increased costs for multiple isolation points Battery back-up systems Multiple conversion steps Flexibility Increased value at lower power Optimized for battery operated systems

48

48

LVD LVD

Intermediate Bus Architecture:


88% overall efficiency

STRENGTHS:
Flexibility (bus voltage options) Multiple high di/dt loads Provides ground isolation Competitive cost Increased efficiencies Increased power densities

WEAKNESSES:
Lowest efficiency - 3 conversion stages Lowest power density Multiple conversion steps

48V RECTIFICATION 48V RECTIFICATION OPTIONAL BATTERIES OPTIONAL BATTERIES

48

48

LVD LVD

AC to 12V Bus Architecture:


91% overall efficiency

STRENGTHS:
Highest efficiency Best power density Improved EMI performance Lowest cost

WEAKNESSES:
Circulating current issues Higher I2R losses Few battery back-up options No secondary grounds

12V RECTIFICATION 12V RECTIFICATION

DESCRIPTION PAGE(S)

DESCRIPTION PAGE(S)

Additional Info. . . . . . . . . . 10-12, 25-32


Remote Power . . . . . . . . . . . . . . . . . . . . . . . 11 Compact PCI. . . . . . . . . . . . . . . . . . . . . . . . . 12 Digital Power Solutions . . . . . . . . . . . . 25-26 Vertical Industry Solutions. . . . . . . . . 27-28 Custom Capabilities . . . . . . . . . . . . . . . 29-30 Engineering Resources & Tools. . . . . . . . 31 The Company. . . . . . . . . . . . . . . . . . . . . . . . 32
1

Front End / Rectifiers. . . . . . . . . . . 3-10


12V Front Ends. . . . . . . . . . . . . . . . . . . . . . . 6
850-2,500 Watts

24V & 48V Front Ends . . . . . . . . . . . . . . . . 7


500-4,000 Watts

24V & 48V Rectifiers. . . . . . . . . . . . . . . . . . 8


1,200-4,000 Watts

Power Shelves. . . . . . . . . . . . . . . . . . . . . . . . 9
6,000-12,000 Watts

Energy Systems. . . . . . . . . . . . . . . . . . . . . . 10
1,600-10,900 Watts

For product details, browse our website: ge.com/powerelectronics

GE Energys Power Electronics business provides a competitive edge with end-to-end power solutions that offer size, efficiency and cost advantages while reducing risk with standards-based power components.

Isolated DC-DC Converters


ISOLATED / REGULATED CONVERTER ISOLATED / REGULATED CONVERTER 92% Efficiency
92% Efficiency

Non-Isolated Point-of-Load Modules


NON-ISOLATED / POL NON-ISOLATED NON-ISOLATED / / POL POL
96% Efficiency NON-ISOLATED / POL 96% Efficiency

LOAD 2.5V 2.5V 1.2V 1.2V LOAD LOAD LOAD LOAD

8V

8V

8V

8V

FULLY REGULATED BUS CONVERTER FULLY REGULATED BUS CONVERTER 96% Efficiency
96% Efficiency

12V 12V

NON-ISOLATED / POL NON-ISOLATED / / POL POL NON-ISOLATED NON-ISOLATED NON-ISOLATED / / POL POL NON-ISOLATED NON-ISOLATED / / POL POL
96% Efficiency NON-ISOLATED / POL 96% Efficiency

3.3V 3.3V 2.5V 2.5V 1.8V 1.8V 1.2V 1.2V

LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD

12V 12V

NON-ISOLATED / POL NON-ISOLATED NON-ISOLATED / / POL POL NON-ISOLATED NON-ISOLATED / / POL POL NON-ISOLATED NON-ISOLATED / / POL POL
96% Efficiency NON-ISOLATED / POL 96% Efficiency

3.3V 3.3V 2.5V 2.5V 1.8V 1.8V 1.2V 1.2V

LOAD LOAD LOAD LOAD LOAD LOAD LOAD LOAD

DESCRIPTION PAGE(S)

DESCRIPTION PAGE(S)

Isolated Converters . . . . . . . . . . 13-20


Regulated Converters . . . . . . . . . . . . 15-17
2-70 Amps

Point-of-Load. . . . . . . . . . . . . . . . 21-24
Surface Mount Modules. . . . . . . . . . . . 24
2-50 Amps

Fully Regulated Bus Converters. . . . . . . . . . 18


10-33 Amps

SIP Modules . . . . . . . . . . . . . . . . . . . . . . . 24
2-60 Amps

Power Amplifiers . . . . . . . . . . . . . . . . . . 19
350-700 Watts

Digital Converters. . . . . . . . . . . . . . . . . 25
3-40 Amps

Filter & PIM Modules. . . . . . . . . . . . . . . 20


5-20 Amps

Digital Converters . . . . . . . . . . . . . . . . . . . 25
1-70 Amps

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

Front End & Rectifier Solutions

Total Cost of Ownership 12V Front Ends 24V & 48V Front Ends 24V & 48V Rectifiers Power Shelves Energy Systems

Page 5 6 7 8 9 10

Product Matrix:
1000W 1500W 2000W 2500W 3000W 3500W CLP0212FP CAR0812FP CAR1212FP CAR1212DC CAR1612FP CAR2512DC CAR2512FP CAR1248FP CAR2024FP CAR2548FP CAR2548DC CAR3000 CAR4000 EP1000_U CAR1248TN CP2000DC54 CP2000TE CP2500TE CP2500DC CAR2548TN CP2725TE CAR3000T CAR4000T 12V 12V 12V 12V 12V 12V 12V 48V 24V 48V 48V 24 / 48V 24 / 48V 48V 48V 48V 48V 48V 48V 48V 48V 24 / 48V 24 / 48V I2C /PMBus I2C /PMBus I2C /PMBus I2C /PMBus I2C /PMBus I2C /PMBus I2C /PMBus I2C /PMBus I2C /PMBus I2C /PMBus I2C I2C RS485 I2C /PMBus I2C I2C /RS485 I2C /RS485 I2C /RS485 I2C /PMBus I2C /RS485 I2C I2C OF 1U 1U 1U 1U 1U 1U 1U 1U 1U 1U 3U 3U 1U 1U 1U 1U 1U 1U 1U 1U 3U 3U 1 (110/220 VAC) 1 (110/220 VAC) 1 (110/220 VAC) 48VDC 1 (110/220 VAC) 48VDC 1 (110/220 VAC) 1 (110/220 VAC) 1 (110/220 VAC) 1 (110/220 VAC) 48VDC 1-3 (220 VAC) 1 or 3 (220 VAC) 1 (110/220 VAC) 1 (110/220 VAC) 48VDC 1 (110/220 VAC) 1 (110/220 VAC) 1 (110/220 VAC) 1 (110/220 VAC) 1 (110/220 VAC) 1 or 3 (220 VAC) 1 or 3 (220 VAC) 200W 850W 1200W 1200W 1600W 2500W 2500W 1200W 2000W 2500W 2500W 3000W 4000W 1000W 1200W 2000W 2000W 2500W 2500W 2500W 2725W 3000W 4000W 4000W 200W 500W

Front Ends Page 6

12V

24/48V
Front Ends Page 7

24/48V
Rectifiers Page 8

Featured Product:

CLP0212
12Vdc 200 watts Open Frame  High efficiency operation - 88.5% @ 20% load - 92% peak efficiency High power density of 18W/in3 2.00 x 4.00 x 1.4 (DxWxH)/ 50.8 x 101.6 x 35.6mm Remote on/off

Total Cost of Ownership

Our customers are pressed to meet the growing demands for energy conservation and space reduction within their markets. Rising power costs, expensive cooling strategies in the Data Center, and precious real estate are of paramount concern. Its a question of Total Cost of Ownership. Our customers are asking: How can we increase end-to-end efficiency? How can we reduce our footprints? How can we dissipate less heat?

GE Energy has released several new power platforms that extend our offering while providing leading operational efficiencies in high-density packages to address these growing demands. Our front ends & rectifiers offer leading edge performance: Power density in excess of 30W/in3 >10 kilowatts in a 1U / 19 rack-mount shelf 12V / 1 U high front-end with 2500 watts of power >92% efficiencies starting at only 20% load

Save space, reduce power consumption and generate less heat. GE Energy offers a complete range of high-efficiency/high-density power solutions to reduce your systems Total Cost of Ownership.

Size Premium:

Increasing performance while available system space continually shrinks

Temperature Rising:

Cooling costs outpace server costs due to increased loads in higher densities

Total Cost of Ownership Reduction


Lifetime Energy Saving per Server (kWh) 480 - 1290 1932 - 3366 21716 - 36000

$3,168
Savings over installed base

$4,465
Savings over installed base

Silver Standard

Server Class Volume Mid-Range High-End

Gold Standard

Volume Mid-Range High-End

740- 1800 2680- 4710 30336- 50742


Installed Base Silver Tier Gold Tier

* Engergy costs are 8.8 cents per kWh (per EPA) * Datacenter PSU loaded at 20% of rated power

Life Time Savings of High End Server (6 yrs)

Savings are calculated using data from the 80 Plus Server Project. GE Energy products would enable system designs to exceed the 80 Plus Gold Standard yielding increased Total Cost of Ownership reduction.

For product details, browse our website: ge.com/powerelectronics

12V Front Ends

CAR0812FP
850 watts / 12Vout Efficiency of 90% @ 20% load (92% peak) Power density of 18W/in3 Universal AC input range with active PFC 8.73 x 3.38 x 1.65 / 221.7 x 85.9 x 41.9mm I2C / PMBus digital interface

850W 1200W 1600W 2400W 850W 1200W 1600W 2400W

CAR1212FP
1,200 watts / 12Vout High efficiency operation - up to 89% Power density of 16W/in3 Universal AC input range with active PFC 11.20 x 4.00 x 1.65 / 284.5 x 101.6 x 41.9mm I2C / PMBus digital interface

CAR1212DC
1,200 watts / 12Vout 36-75VDC input range High efficiency operation - up to 90% Power density of 16W/in3 11.20 x 4.00 x 1.65 / 284.5 x 101.6 x 41.9mm I2C / PMBus digital interface

48Vin

850W 1200W 1600W 2400W

CAR1612FP
1,600 watts / 12Vout Efficiency of 92.4% @ 20% load (94.5% Peak) Power density of 20W/in3 Universal AC input range with active PFC 12.45 x 4.00 x 1.65 / 316.23 x 101.6 x 41.9mm I2C / PMBus digital interface
PLATINUM

EW N

850W 1200W 1600W 2400W

CAR2512DC
2,500 watts / 12Vout 36-75VDC input range High efficiency operation - up to 92% Power density of 25W/in3 15.38 x 4.00 x 1.65 / 390.5 x 101.6 x 41.9mm I2C / PMBus digital interface

48Vin

850W 1200W 1600W 2400W 850W 1200W 1600W 2500W

CAR2512FP
2,500 watts / 12Vout Efficiency of 90% @ 20% load (92.1% peak) Power density of 25W/in3 Universal AC input range with active PFC 15.38 x 4.00 x 1.65 / 378.0 x 102.0 x 41.9mm I2C / PMBus digital interface

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

24V & 48V Front Ends

CAR1248FP
1,200 watts / 48Vout High efficiency operation - up to 91% Power density of 19W/in3 Universal AC input range with active PFC 11.20 x 3.44 x 1.65 / 284.5 x 87.4 x 41.9mm I2C / PMBus digital interface Mates with ACE125 shelf

1200W 2000W 2500W 4000W 1200W 2000W 2500W 4000W


EW N !

CAR2024FP
2,000 watts / 24Vout High efficiency operation - up to 90.5% Power density of 21W/in3 Universal AC input range with active PFC 14.25 x 4.00 x 1.65 / 316.2 x 101.6 x 41.9mm I2C / PMBus digital interface Mates with ACE204 shelf

CAR2548FP
2,500 watts / 48Vout High efficiency operation - up to 91% Power density of 27W/in3 Universal AC input range with active PFC 14.25 x 4.00 x 1.65 / 362.0 x 102.0 x 40.9mm I2C / PMBus digital interface Mates with ACE254 shelf

1200W 2000W 2500W 4000W

CAR2548DC
2,500 watts / 48Vout High efficiency operation - up to 91% Power density of 27W/in3 36-75Vdc input range 14.25 x 4.00 x 1.61 / 362.0 x 102.0 x 40.9mm I2C / PMBus digital interface Mates with ACE254 shelf

48Vin

1200W 2000W 2500W 4000W

For product details, browse our website: ge.com/powerelectronics

24V & 48V Rectifiers


N EW !

EP0800TE / EP1000TE / EP1600TE


800, 1,000 or 1,600 watts / 54V output High efficiency operation - up to 95% Power density up to 27W/in3 Universal AC input range with active PFC 8.19 x 4.58 x 1.58 / 208.0 x 116.5 x 40.2mm RS485 communication interface Mates with SPS shelf family RoHS6

800W 1000W 1600W 2000W 2500W 4000W 1000W 1200W 2000W 2500W 4000W

CAR1248TN
1,200 watts / 48Vout High efficiency operation - up to 91% Power density of 19W/in3 Universal AC input range with active PFC 11.20 x 3.44 x 1.65 / 284.5 x 87.4 x 41.9mm I2C / PMBus digital interface Mates with ACE125 shelf

CP2000DC54 / CP2500DC54
2,000 or 2,500 watts / 54V output 40-60VDC input range High efficiency operation - up to 92% Power density up to 27.6W/in3 13.85 x 4.00 x 1.63 / 352.0 x 101.6 x 41.4mm I2C digital interface Mates with CPL PEM shelf

48Vin

POE READY

EW

1000W 1200W 2000W 2500W 4000W

CP2000TE / CP2500TE / CP2725TE


2,000, 2,500 or 2,725 watts / 54Vout High efficiency operation - approaching 97% Power density of 30W/in3 13.85 x 4.00 x 1.63 / 356.0 x 101.6 x 41.4mm I2C and RS485 communication interface Mates with CPL shelf family
PLATINUM

POE READY

1000W 1200W 2000W 2500W 4000W 1000W 1200W 2000W 2500W 4000W

CAR2548TN
2,500 watts / -48Vout High efficiency operation - up to 91% Power density of 27W/in3 14.25 x 4.00 x 1.61 / 362.0 x 102.0 x 40.9mm I2C / PMBus digital interface Mates with ACE254 shelf

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

Power Shelves

ACE125
48V front end or rectifier shelf Mates with CAR1248 modules 5 bay power shelf 5 x 1,200W power modules 4,800W N+1 redundant 6,000W total power 1U High 19 / 483.0mm rack mount 14.98 / 380.5mm depth Class B emissions with fully-populated shelf

ACE254
48V front end or rectifier shelf Mates with CAR2548 or CAR2024 modules 4 Bay power shelf 4 x 2,500W power modules 10,000W total power 7,500W N+1 redundant 1U High 19 / 483.0mm rack mount 18.07 / 459.0mm depth Class B emissions with fully-populated shelf

EW

EW

ACE084
12V front end or rectifier shelf Mates with CAR0812FP & CAR0812DC modules 4 bay power shelf 4 x 850W power modules 3,400W total power 2,550W N+1 redundant 1U High 19 / 483.0mm rack mount 12.7 / 322.6mm depth Class B emissions with fully-populated shelf

ACE164
12V front end or rectifier shelf Mates with CAR1612 modules 4 bay power shelf 4 x 1,600W power modules 6,400W total power 4,800W N+1 redundant 1U High 19 / 483.0mm rack mount 16.4 / 416.6mm depth Class A emissions with fully-populated shelf

For product details, browse our website: ge.com/powerelectronics

Dozens of standard configurations are available including options for batteries, enclosures, sensors and cables. Please contact our technical support team to discuss your specific installation requirements.

48Vdc Energy Systems

SPS Platform
48V rectifier shelf Mates with EP800/1000/1600 rectifier modules 1U High 19 / 483mm rack mount Maximum 10.37 / 264.0mm depth Adjustable mounting ears (flush or mid-mount) Rear / front panel DC distribution options Breaker and fuse panel options Optional pulsar edge controller

Pulsar Edge Controller


Available for both CPL & SPS platforms Compact design installs in shelf Preserves rectifier slots  Advanced rectifier and battery management Web based GUI or front panel control Extensive alarm capability & data logging RJ45 craft and ethernet ports Up to 5 Form C Relay Contacts

CPL Platform
48V rectifier shelf I2C or RS485 control options  Mates with CP2000TE / CP2500TE / CP2725TE rectifier modules 1U High 19 / 483mm rack mount Maximum 17.21 / 487.0mm depth Adjustable mounting ears (flush or mid-mount) Rear / front panel DC distribution options Breaker and fuse panel options Optional Pulsar Edge Controller CP2000TE and CP2725TE are 80 PLUS Platinum certified Compact 1U and up to 30W/in3  CPL is a highly flexible solution which can be used in embedded OEM applications or external rack-mounted applications  CPL line provides AC to 48V power conversion downstream of an AC UPS system or as the primary power conversion step in DC UPS systems that have direct connected battery backup  Two communications protocols are onboard every power supply adding to its flexibility - I2C protocol for use in OEM embedded applications helps you fully integrate the power supply into your platform - RS485 communications using Galaxy Protocol allows standalone systems full alarm and communication capability as well as battery management Versions available with POE isolation For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

10

Remote Power

CPS3200U Upstream Converter:


The CPS3200U Upstream Converter is a 2U High Rack Mounted Power System that allows remote 48Vdc devices to be powered using existing twisted-pair T1/E1 copper wire facilities. This allows power to triple-play electronics at the Serving Area Interface (SAI) to be remotely fed from a centrally located power office. For power transmission across the copper pairs, 48V power is converted to +190V and then down-converted to 48Vdc at the remote end. The CPS3200U shelf accommodates up to 32 channels of 100VA power-limited circuits (multishelf configurations are available). The two-circuits per module layout makes provisioning simple (matches the CPS2500D Downstream Converter). Craft safety is enhanced by providing current limit and ground fault safety circuitry. Both front access and rear access versions are available, configured for convenient installation and service.

Applications:
Service Provider OEMs Fiber-To-The-Node (FTTN) networks Fiber-To-The-Curb (FTTC) networks Remote power, express power, span power or line power deployments Powering telecom equipment over twisted pair (RFT-V) Powering access electronics using the existing copper network

Features:
Short circuit, overload, overvoltage and undervoltage shutdown circuits -40C to 75C operating temperature 32 190Vdc 100VA output circuits Inrush protected, hot swap modules Full front access for cabling with simple craft interface 5 mA ground fault shutdown for A2 safety level Front panel LED Indicators Vertical airflow Compact outdoor cabinet versions available

CPS3200U Specifications: CPS2500D Downstream Converter:


The CPS2500D Downstream Converter is a 1U High 19 Rack Mount Power System that converts 190V into bulk 48VDC at the downstream end Serving Area Interface (Cross-Connect cabinet). The shelf can house up to ten power modules for a total of 1300W capability. Each power module has two DC-DC circuits providing a total of 20 input channels. The LED interface on the front of each power module helps quickly diagnose and resolve network issues. Each shelf is equipped with a Power Major and a Power Minor form-C alarm relay. Input range: -40Vdc to -59Vdc 190VDC output voltage Output power of 190 VA per module Output conducted noise spectrum < GR1089 limits (10kHz to 30MHz) Fused & polarity input protection Over/under voltage, overcurrent and ground fault shutdown Max input current at 40.0Vin 5.8A per card (two converters per card) Output current ground fault limit: 5mA (each circuit)

CPS2500D Specifications:
Nominal input voltage: 190Vdc Output power (RFT-V): 65W per channel, 1300W per shelf maximum Input voltage range: 95Vdc (190Vdc) to 190Vdc (380Vdc) Number of inputs: 20 Typical input current limit: 0.226A Input via RJ-21 male connector Output voltage setpoint: -54.5Vdc Input protection: inrush, internal fuse

11

For product details, browse our website: ge.com/powerelectronics

Compact PCI

The GE Energy Compact PCI power supplies are highly reliable power supplies designed for use in communications, industrial, aerospace, and other applications. These power supplies offer high power density in plug-in modules that meet the requirements of the PICMG 2.11 power interface specification for Compact PCI systems. Our products feature: PICMG 2.11 3U x 8HP compliant products Universal AC input models (90-264 Vac with Active PFC) 48Vdc input models (36 - 72Vdc input range) UL, CUL & TUV safety certifications Active current share for parallel operation Hot-swap / N+1 redundant operation No minimum load eliminates the need for preload on system backplane Active current share for increased reliability & scalability Available in AC or DC input models for a single source of both input versions

AC INPUT MODELS
Model CMP150 Power 150 Watts Outputs 5V @ 20A 3.3V @ 33A 12V @ 8A -12V @ 1.5A 5V @ 25A 3.3V @ 35A 12V 2 8A -12V @ 1.5A 5V @ 50A 3.3V @ 50A 12V @ 12A -12V @ 4A Package 3U 6.68 x 5.07 x 1.59 169.7 x 128.7 x 40.3mm

CMP200

200 Watts

3U

6.68 x 5.07 x 1.59 169.7 x 128.7 x 40.3mm

CMP400

400 Watts

6U

6.76 x 1.58 x 10.31 171.8 x 40.2 x 261.9mm

48Vdc INPUT MODELS (36-72 Vin Range)


Model DMP150 Power 150 Watts Outputs 5V @ 20A 3.3V @ 33A 12V @ 8A -12V @ 1.5A 5V @ 25A 3.3V @ 35A 12V @ 8A -12V @ 1.5A 5V @ 50A 3.3V @ 50A 12V @ 12A -12V @ 4A Package 3U 6.68 x 5.067 x 1.588 in. 169.7 x 128.7 x 40.3 mm

DMP200

200 Watts

3U

6.68 x 5.067 x 1.588 in. 169.7 x 128.7 x 40.3 mm

DMP400

400 Watts

6U

6.762 x 1.584 x 10.311 in. 171.8 x 40.2 x 261.9 mm

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

12

Isolated DC-DC Converters

Page 15 16 17 18 19 20

Low Power & 1/16 Bricks. . . . . . . . . . . . . . . . . . . . . . . . . . . 1/8 Bricks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1/4 & 1/2 Bricks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fully Regulated Bus Converters . . . . . . . . . . . . . . . . . . . . Power Amplifiers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filter & PIM Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Product Matrix:
100W 200W 300W
MODEL
Page 15

INPUT VOLTAGE 24 / 48V 24 / 48V 36-75V 36-75V 36-75V 36-75V 18-75V 36-75V 36-75V 36-75V 36-75V 36-75V 36-75V 36-75V

ISOLATION 2250Vdc 1500Vdc 2250Vdc 2250Vdc 2250Vdc 2250Vdc 2250Vdc 1500Vdc 1500Vdc 1500Vdc 2250Vdc 2250Vdc 2250Vdc 2250Vdc

FOOTPRINT 1X1 1X2 1/16 BRICKS 1/8 BRICKS

OUTPUT VOLTAGE 3.3 15V 1.8 - 5V 3.3 5V 3.3 15V 5 - 12V 5 12V 3.3 - 12V 1.2 12V 1.2 - 3.3V 1.2 12V 8.1 - 13.2V 8.1 - 13.2V 6.0 - 13.2V 6.0 - 13.2V

MAX POWER 3.3 15W 12A / 33W 20A / 66W 25A / 82W 15A / 84W 20A / 120W 20A / 75W 40A / 120W 60A / 165W 70A / 204W 33A / 400W 33A / 400W 25A / 300W 25A / 300W

Page 16

Page 17 Page 17 Page 17

SC / SW HC / HW KNW ESTW EHW EVW EHHD QRW QPW JRW QBDW (DIGITAL) QBVW EBDW (DIGITAL) EBVW

Isolated & Regulated DC-DC Converters

1/4 BRICKS 1/4 BRICKS 1/2 BRICKS 1/4 BRICKS 1/4 BRICKS 1/8 BRICKS 1/8 BRICKS

Fully Regulated Bus Converters

Page 18 Page 18

350~700 watt RF Amplifier Converters listed on Page 19 DC Filters and ATCA PIM Modules listed on Page 20

D i s t r i b u t e d - p o w e r O p e n S t a n d a r d s A l l i a n c e

13

400W

0W

Featured Product:

Barracuda Series
High efficiency of 96% Input voltage range 36 75Vdc DOSA standard eighth and quarter brick Digital interface with PMBus Fully regulated bus converters  Forward and backwards compatible with standard 5-pin bus and fully digital modules Remote sense and output voltage trim Negative remote on/off logic

14

Isolated Low Power & 1/16 Bricks

D i s t r i b u t e d - p o w e r O p e n S t a n d a r d s A l l i a n c e

SC / SW Series
15W / 3.5A Max Power
24 & 48Vdc input models 3.3-15Vdc output models 1.10 x 0.96 x 0.34 / 27.94 x 24.38 x 8.5mm Surface-mount or through-hole High efficiency operation up to 88% Remote on/off control

MODEL SC003A5F SC003A0A SC001A2B SW003A5F SW003A0A SW001A2B SW001A0C

INPUT VOLTAGE 24V (18-36V) 24V (18-36V) 24V (18-36V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 3.3V 5V 12V 3.3V 5V 12V 15V

OUTPUT CURRENT 3.5A 3A 1.2A 3.5A 3A 1.2A 1A

EFFICIENCY 86% 86% 85% 85% 86% 87% 88%

HC / HW Series
33W / 12A Max Power
24 & 48Vdc input models 1.2-5Vdc output models 1.86 x 1.16 x 0.34 / 47.2 x 29.5 x 8.5mm Surface-mount or through-hole High efficiency operation up to 91% Remote on/off control

MODEL HC005A0F HC004A0A HW005A0F HW004A0A

INPUT VOLTAGE 24V (18-36V) 24V (18-36V) 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 3.3V 5V 3.3V 5V

OUTPUT CURRENT 5A 4A 5A 4A

EFFICIENCY 86% 88% 87% 89%

HC010A0F HC006A6A HW012A0Y HW010A0G HW010A0F HW006A6A

24V (18-36V) 24V (18-36V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V)

3.3V 5V 1.8V 2.5V 3.3V 5V

10A 6.6A 12A 10A 10A 6.6A

90% 91% 85% 89% 90% 91%

KNW Series

66W / 20A Max Power


48Vdc input models 3.3-5Vdc output models 1.30 x 0.90 x 0.40 / 33.0 x 22.9 x 10.2mm Surface-mount or through-hole High efficiency operation up to 92% Remote on/off control, sense and trim functions

MODEL KNW020A0F KNW013A0A KNW015A0F

INPUT VOLTAGE 48V (36-75V) 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 3.3V 5V 3.3V

OUTPUT CURRENT 20A 13A 15A

EFFICIENCY 91% 91% 92%

2250Vdc Isolation for PoE Applications

15

For product details, browse our website: ge.com/powerelectronics

D i s t r i b u t e d - p o w e r O p e n S t a n d a r d s A l l i a n c e

Isolated 1/8 Bricks

Stingray Series
82W / 25A Max Power
48Vdc input model 3.3 to 15Vdc output model 2.28 x 0.90 x 0.34 / 57.9 x 22.8 x 8.52mm Surface-mount or through-hole High efficiency operation up to 92% On/off, remote sense & trim functions

MODEL ESTW015A0F ESTW025A0F ESTW004A2C ESTW010A0A

INPUT VOLTAGE 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 3.3V 3.3V 15V 5V

OUTPUT CURRENT 15A 25A 4.2A 10A

EFFICIENCY 91% 92% 90% 91%

2250Vdc Isolation for PoE Applications

EHW Series

84W / 15A Max Power


48Vdc input models 5 to 12Vdc output models 2.30 x 0.90 x 0.32 / 58.4 x 22.8 x 8.1mm Surface-mount or through-hole High efficiency operation up to 93% On/off, remote sense & trim functions Optional baseplate

MODEL EHW015A0A EHW007A0B

INPUT VOLTAGE 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 5V 12V

OUTPUT CURRENT 15A 7A

EFFICIENCY 92% 93%

2250Vdc Isolation for PoE Applications

EVW Series

120W / 20A Max Power


48Vdc input models 5 to 12Vdc output models 2.30 x 0.90 x 0.32 / 58.4 x 22.8 x 8.1mm Surface-mount or through-hole High efficiency operation up to 93% Enable, sense and trim functions Optional baseplate

MODEL EVW020A0A EVW020A0S6R0 EVW010A0B

INPUT VOLTAGE 48V (36-75V) 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 5V 6V 12V

OUTPUT CURRENT 20A 20A 10A

EFFICIENCY 92% 92% 93%

2250Vdc Isolation for PoE Applications

EW

Hammerhead Series
75W / 20A Max Power
18 - 75Vdc wide input modules 3.3, 5, and 12Vdc output modules 2.28 x 0.90 x 0.30 / 57.9 x 22.8 x 7.6mm Surface mount or through-hole High efficiency operation up to 93% Optional baseplate

MODEL EHHD006A0B EHHD015A0A EHHD020A0F

INPUT VOLTAGE 18-75V 18-75V 18-75V

OUTPUT VOLTAGE 12V 5V 3.3V

OUTPUT CURRENT 6A 15A 20A

EFFICIENCY 93% 91% 91%

2250Vdc Isolation for PoE Applications

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

16

Isolated 1/4 & 1/2 Bricks

D i s t r i b u t e d - p o w e r O p e n S t a n d a r d s A l l i a n c e

QRW Series

120W / 40A Max Power


48Vdc input models 1.2-12Vdc output models 2.28 x 1.45 x 0.42 / 57.9 x 36.8 x 10.6mm Surface-mount or through-hole Optional baseplate High efficiency operation up to 92% Enable, sense and trim functions

MODEL QRW025A0P QRW025A0M QRW025A0G QRW025A0F QRW025A0A QRW040A0M QRW040A0Y QRW035A0G QRW035A0F QRW010A0B

INPUT VOLTAGE 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 1.2V 1.5V 2.5V 3.3V 5V 1.5V 1.8V 2.5V 3.3V 12V

OUTPUT CURRENT 25A 25A 25A 25A 25A 40A 40A 35A 35A 10A

EFFICIENCY 85% 87% 90% 91% 92% 86% 87% 90% 91% 91%

QPW Series

165W / 60A Max Power


48Vdc input models 1.2-3.3Vdc output models 2.28 x 1.45 x 0.42 / 57.9 x 36.8 x 10.6mm Through-hole package Optional baseplate High efficiency operation up to 93% Enable, sense and trim functions

MODEL QPW025A0F QPW060A0P QPW060A0M QPW060A0Y QPW060A0G QPW050A0F

INPUT VOLTAGE 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 3.3V 1.2V 1.5V 1.8V 2.5V 3.3V

OUTPUT CURRENT 25A 60A 60A 60A 60A 50A

EFFICIENCY 93% 85% 87% 89% 91% 93%

JRW Series

204W / 70A Max Power


48Vdc input models 1.5-12Vdc output models 2.40 x 2.30 x 0.38 / 61.0 x 58.4 x 9.5mm Through-hole package Optional baseplate High efficiency operation up to 92% Enable, sense and trim functions

MODEL JRW070A0M JRW065A0Y JRW065A0G JRW060A0F JRW040A0A JRW017A0B

INPUT VOLTAGE 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V)

OUTPUT VOLTAGE 1.5V 1.8V 2.5V 3.3V 5V 12V

OUTPUT CURRENT 70A 65A 65A 60A 40A 17A

EFFICIENCY 86% 87% 90% 91% 92% 92%

17

For product details, browse our website: ge.com/powerelectronics

D i s t r i b u t e d - p o w e r O p e n S t a n d a r d s A l l i a n c e

Fully Regulated Bus Converters

The new GE Energy Barracuda family of digitally controlled, fully regulated bus converters are DOSA compliant, drop-in replacements for unregulated and semi-regulated bus converters challenged by recent industry-wide intellectual property issues.

Fully Regulated Bus Converters:


N EW !
1/8 Brick MODEL EBVW020A0B EBDW020A0B EBVW025A0B EBDW025A0B 1/4 Brick MODEL QBVW025A0B QBDW025A0B QBVW033A0B QBDW033A0B INPUT VOLTAGE 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) OUTPUT VOLTAGE 12V 12V 12V 12V OUTPUT CURRENT 25A 25A 33A 33A EFFICIENCY 96% 96% 96% 96% INPUT VOLTAGE 48V (36-75V) 48V (36-75V) 48V (36-75V) 48V (36-75V) OUTPUT VOLTAGE 12V 12V 12V 12V OUTPUT CURRENT 20A 20A 25A 25A EFFICIENCY 95% 95% 95% 95%

Barracuda Series
400W / 33A Max Power
36-75Vdc input model 12Vdc output model High efficiency operation up to 96% Remote sense and output voltage trim DOSA-standard quarter and eighth brick Digital interface with PMBus Negative remote on/off logic  Output overcurrent/ overvoltage protection Overtemperature protection  Wide operating temperature range (-40C to 85C) 1/8 Brick - 2.30 x 0.90 x 0.44 / 58.4 x 22.8 x 11.3mm 1/4 Brick - 2.30 x 1.45 x 0.46 / 58.4 x 36.8 x 11.7mm Optional baseplate

Pin # 1 2 3 4 8

Pin Name VIN (+) ON/OFF VIN (-) VOUT (-) VOUT (+)

Pin # 1 2 3 4 5

Pin Name VIN (+) ON/OFF VIN (-) VOUT (-) SENSE (-)

Pin # 6 7 8 9 10

Pin Name TRIM/C1 SENSE (+) VOUT (+) C2 DATA

Pin # 11 12 13 14 15

Pin Name SIG_GND SMBALERT CLK ADDR1 ADDR0

Barracuda Analog Series


Analog 5-pin IBA pin-out Drop-in replacement for semi-regulated and unregulated bus converters

Barracuda Digital Series


 Conforms to new DOSA standard for Second Generation Single Output Pin DC-DC Converters with Digital Connections  Fully backwards compatible with existing quarter and eighth bricks Digital interface with PMBus Two user configurable pins

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

18

Power Amplifiers

1/2 Brick:
A new generation of power modules designed for maximum cost effectiveness and power density, the industry standard half-brick series DC-DC converter is an ideal choice for high voltage and power amplifier applications.
N EW !

Orca Series
450 watts maximum power 36-75Vdc input/28 - 48Vdc output model Output voltage adjustment trim, 16.0 to 35.2Vdc or 28.8 - 57.6Vdc High efficiency operation up to 94% Integral metal baseplate with optional threaded inserts Optional Tunable Loop for optimized output capacitance Operates at full power to case temperatures of 100C 2.27 x 2.39 x 0.5 / 57.7 x 60.7 x 12.7mm
MODEL JRCW016A0R JRCW450R JRCW450U INPUT VOLTAGE 48V (36 - 75V) 48V (36 - 75V) 48V (36 - 75V) OUTPUT VOLTAGE 28V 32V 48V OUTPUT CURRENT 16A 14A 14A EFFICIENCY 94% 94% 94%

JNC/JNW350 Module
350 watts maximum power 18-36 / 36-75Vdc input/28Vdc output model Output voltage adjustment trim, 16.8 to 32.0Vdc High efficiency operation up to 92% Integral metal baseplate with optional threaded inserts Optional Tunable Loop for minimized output capacitance Operates at full power to case temperatures of 85C 2.27 x 2.39 x 0.5 / 57.7 x 60.7 x 12.7mm
MODEL JNC350R JNW350R INPUT VOLTAGE 18V - 36V 36V - 75V OUTPUT VOLTAGE 28V 28V OUTPUT CURRENT 12.5A 12.5A EFFICIENCY 91% 92%

Full Brick:
A new generation of open frame isolated DC-DC converters in an industry-standard full-brick package suitable for wireless base stations and other similar telecom equipment including RF power amplifier applications, wireless networks, and switching networks.

FNW700 Module
700 watts maximum power 36-75Vdc input / 28Vdc output model Output voltage adjustment trim High efficiency operation up to 90% Integral metal baseplate with optional threaded inserts Operates at full power to case temperatures of 90C at 700 watts 4.6 x 2.4 x 0.5 / 116.6 x 61.0 x 12.7mm

19

For product details, browse our website: ge.com/powerelectronics

Filter & PIM Modules

Filter Modules
The internal operation of DC-DC converters utilizes pulsed voltages and currents, which can generate broad-spectrum noise that results in electromagnetic emissions. To ease the task of meeting International Standards that limit emissions, GE Energy offers a range of input filter modules with current ratings of 5A, 7A, 10A, 12A, and 20A. One properly sized filter module can be used with one or multiple DC-DC converter modules. Our filter modules reduce the levels of conducted common-mode and differential-mode noise, providing high insertion loss throughout the frequency range regulated by such bodies as the International Special Committee on Radio Interference (CISPR) and the U.S. Federal Communications Commission (FCC). All of our filter modules are rated for differential input voltages up to 75Vdc and common-mode input voltages up to 1500Vdc. For further details on managing EMC, refer to individual DC-DC module and filter datasheets. Model FLT007A0Z FLT012A0Z FLTR75V05Z FLTR100V10Z FLTR100V20Z Rated Voltage 0-75V 0-75V 0-75V 0-75V 0-75V Rated Current 7A max 12A max 5A max 10A max 20A max Common-Mode Insertion Loss 60dB 45dB 28dB 36dB 32dB Differential-Mode Insertion Loss 66dB 55dB 25dB 44dB 36dB Resistance per leg (mohms) 25 20 20 14 6.6

Dimensions 25.4 x 25.4 x 12.2 mm 48.3 x 25.4 x 11.7 mm 25.4 x 25.4 x 10.2 mm 51 x 28 x 12 mm 50.8 x 40.6 x 12.7 mm

FLT007A0Z

FLT012A0Z

FLTR75V05Z

FLTR100V10Z

FLTR100V20Z

Power Input Module


The PIM300 used in conjunction with GE Energy Isolated DC-DC Converters and Non-Isolated Point-of-Load Modules provides a complete, lowcost power architecture that complies with Advanced TCATM board power requirements. The PIM300 provides high-reliability with innovative features and a compact design as a low cost, simple power architecture solution for complex power requirements. Features Delivers up to 300W of rated power High efficiency: 98% typical Inrush current limit protection Integrated filter for CISPR class B EMI limits ORing FETs for A&B feeds A&B feeds loss alarm Hot swap control 72V supply for hold-up/bulk capacitor Through-hole package Measures only 70.6 x 36.8 x 12.7 mm Specifications Input voltage range: 36Vdc to 75Vdc Management power (5V/3.3V): 8W max Operating temperature range: -5C to 85C Basic insulation Protection features Output current and overtemperature protections Transient overvoltage protection Input undervoltage lockout Short circuit protection

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

20

Non-Isolated Point-of-Load Converters

Page

Tunable LoopTM Technology DLynxTM POL Modules ProLynx POL Modules TLynx POL Modules

23 24 24 24 24 25

Naos RaptorTM POL Modules Digital Power Solutions

Product Matrix:
INPUT VOLTAGE
PicoDLynx

OUTPUT VOLTAGE 0.60-5.5V 0.60-5.5V 0.60-5.5V 0.45-5.5V 0.45-5.5V 0.45-5.5V 0.60-5.5V 0.45-5.5V 0.60-2.0V 0.45-2.0V 3.0-18.0V 3.0-18.0V 0.60-5.50V 0.60-8.0V 0.60-3.63V 0.60-5.5V 0.80-3.63V 0.70-2.0V 0.60-5.5V 0.60-5.5V 0.59-6.0V 0.59-6.0V 0.59-6.0V 0.59-6.0V 0.60-5.0V 0.60-2.0V 0.60-5.0V

OUTPUT CURRENT COMMUNICATIONS 3A 6A 12A 3A 6A 12A 20A 20A 40A 40A 3A 5A 2A 4A 12A 20A 30A 50A 2A 10A 3A 6A 10A 20A 40A 50A 60A ANALOG ANALOG ANALOG DIGITAL ANALOG DIGITAL DIGITAL ANALOG

10A

20A

30A

40A

50A

DIMENSIONS 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm

3.0-14.0V 3.0-14.0V 3.0-14.0V 3.0-14.0V 3.0-14.0V

Surface Mount Modules


Page 24

3.0-14.0V
MicroDLynx MegaDLynx ProLynx PicoTLynx MicroTLynx TLynx MegaTLynx GigaTLynx Naos Raptor

3.0-14.0V 3.0-14.0V 4.5-14.4V 4.5-14.4V 9.0-36.0V 9.0-36.0V 3.0-14.0V 8.0-16.0V 2.4-5.5V 2.4-14.0V 4.5-14.0V 4.5-14.0V 3.0-14.0V 4.5-14.0V 4.5-14.0V 4.5-14.0V 4.5-14.0V 4.5-14.0V 5.0-13.8V 5.0-14.0V 5.0-13.8V

20.32 x 11.43 x 8.5mm 20.32 x 11.43 x 8.5mm 33.02 x 13.46 x 10.9mm 33.02 x 13.46 x 10.9mm 20.32 x 11.43 x 8.5mm 20.32 x 11.43 x 8.5mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 20.32 x 11.43 x 8.5mm 33 x 13.46 x 8.5mm 33 x 13.46 x 10mm 33 x 22.9 x 10mm 10.4 x 16.5 x 8.1mm 10.4 x 16.5 x 7.84mm 10.4 x 16.5 x 7.84mm 10.4 x 16.5 x 7.84mm 10.4 x 16.5 x 8.4mm 36.8 x 15.5 x 9.2mm 36.8 x 27.9 x 10.7mm 36.8 x 27.9 x 20.1mm 65.5 x 31.8 x 11.6mm

Single In-Line Package (SIPs)


Page 24

21

60A

0A

EW

Featured Product:

DLynx Series
3A-40A output current 3-14.4Vdc input models 0.45-5.5Vdc output models Dual offering - both digital & analog versions Standards-based DOSA footprint Tunable Loop Digital communication (PMBus) Total Efficiency architecture Superior thermal performance EZ-Sequence Cost efficient open frame design

www.DLynx.info

D i s t r i b u t e d - p o w e r O p e n S t a n d a r d s A l l i a n c e

22

Next-Generation Non Isolated / POL


www.tunableloop.com

Tunable LoopTM Technology


Improved footprints, transient response, and costs The power of Tunable LoopTM is a simple implementation of a resistor and capacitor in series across the point-of-load (POL) Trim and Output pins to optimize POL modules for multiple applications of varying demands. These very small passive devices never exceed a few k resistance or a few hundred nF capacitance. The figure below illustrates the transient response of a 12A PicoTLynx module to a 50% load step with varying external capacitance. The maximum voltage deviation improves from 415mV (0F) to 235mV (3x47F) but the control loop bandwidth drops from 78 to 21kHz, increasing the duration of the voltage excursion. This is consistent with the reduction in control bandwidth and poorer phase margin caused by increased capacitance. Without Tunable Loop: High deviation and reduced control bandwidth with increased output capacitance.

The goal of Tunable LoopTM is to regain the bandwidth lost with increased capacitance. If we fix the value of RTune to 150 and vary CTune from 0pF to 7500pF, we regain control bandwidth back to 82KHz and achieve a 4.8x reduction in voltage deviation. With Tunable Loop: Substantially reduced deviation through improved control bandwidth and reduced output capacitance.

Tunable Loop achieves lower voltage deviation with significantly reduced capacitance. As an example, the 6A PicoTLynxTM module (5Vin / 1.2Vout @ 4A), with a step load of 3A and deviation <4% (48mV) would require 3 electrolytic caps versus 3 ceramic caps with Tunable LoopTM. This results in a $0.60 reduction in external capacitor cost and a footprint reduction of 111mm2 achieving >3X the effective current density.

Caps - No Tune

Caps - Tuned

$1.20 / 157mm2

$.60 / 45.8mm2

50% Cost Reduction 61% Footprint Reduction

23

For product details, browse our website: ge.com/powerelectronics

D i s t r i b u t e d - p o w e r O p e n S t a n d a r d s A l l i a n c e

Tunable Loop POL Converter Modules


Improved footprints, transient response, and costs

www.tunableloop.com
Digital & Analog 4th Generation

DLynx- Surface Mount Models


Models Model # PDT003 PVX003 PDT006 PVX006 PDT012 PVX012 UDT020 UVT020 MDT040 MVT040 Input Voltage 3.0-14.4V 3.0-14.4V 3.0-14.4V 3.0-14.4V 3.0-14.4V 3.0-14.4V 3.0-14.4V 3.0-14.4V 4.5-14.4V 4.5-14.4V Output Voltage 0.45-5.5V 0.60-5.5V 0.45-5.5V 0.60-5.5V 0.45-5.5V 0.60-5.5V 0.45-5.5V 0.60-5.5V 0.45-2.0V 0.60-2.0V Output Current 3A 3A 6A 6A 12A 12A 20A 20A 40A 40A Communications Digital Analog Digital Analog Digital Analog Digital Analog Digital Analog

PicoDLynx

MicroDLynx MegaDLynx

Efficiency 94% 92% 94% 94% 96% 95% 96% 96% 91.5% 91.5%

Dimensions 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 12.2 x 12.2 x 6.25mm 20.32 x 11.43 x 8.5mm 20.32 x 11.43 x 8.5mm 33.02 x 13.46 x 10.9mm 33.02 x 13.46 x 10.9mm

PicoDLynxTM

MicroDLynxTM

MegaDLynxTM

ProLynxTM

ProLynx- Surface Mount Models


Models Model # APXW003 APXW005 Input Voltage 9.0-36.0V 9.0-36.0V Output Voltage 3.0-18.0V 3.0-18.0V Output Current 3A 5A Communications Analog Analog Efficiency 97% 96% Dimensions 20.32 x 11.43 x 8.5mm 20.32 x 11.43 x 8.5mm

ProLynx

TLynx - Surface Mount Models


Models Model # APXS002 APXK004 APTS030 APTS050 Input Voltage 3.0-14V 8.0-16V 6.0-14.0V 4.5-14.0V Output Voltage 0.60-5.5V 0.60-8.0V 0.80-3.63V 0.70-2.0V Output Current 2A 4A 30A 50A Efficiency 96% 96% 96% 95% Dimensions 12.2 x 12.2 x 6.25 mm 12.2 x 12.2 x 6.25 mm 33 x 13.46 x 10 mm 33 x 22.9 x 10 mm

PicoTLynx MegaTLynx GigaTLynx

PicoTLynxTM
(2 Amps)

PicoTLynxTM
(3-12 Amps)

MegaTLynxTM

GigaTLynxTM

Naos Raptor- Single In Line Package (SIP)


Models Model # NQR002 NSR003 NSR006 NQR010 NSR020 NSR040 NSR050 NRS060 Input Voltage 3.014.0V 4.514.0V 4.514.0V 4.5-14.0V 4.5-13.8V 5.0-13.8V 5.0-14.0V 5.0-13.8V Output Voltage 0.60-5.5V 0.59-6.0V 0.59-6.0V 0.59-6.0V 0.59-6.0V 0.60-5.0V 0.60-2.0V 0.60-5.0V Output Current 2A 3A 6A 10A 20A 40A 50A 60A Peak Efficiency 93% 93% 92% 94% 97% 95% 93% 95% Dimensions 10.4 x 16.5 mm x 8.1mm 10.4 x 16.5 mm x 7.84mm 10.4 x 16.5 mm x 7.84mm 10.4 x 16.5 x 8.4mm 36.8 x 15.5 x 9.2mm 36.8 x 27.9 x 10.7mm 36.8 x 27.9 x 20.1mm 65.5 x 31.8 x 11.6mm

Naos Raptor

2 Amp Models

3 / 6 / 10 Amp Models

20 Amp Models

40 / 50 Amp Models

60 Amp Models

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

24

Digital Power Solutions

Digital Converters
GE Energy digitally controlled DC-DC power converters provide power engineers with a broad suite of information and tools to innovate their designs. Digital models offer more flexibility, often require less real estate, and deliver higher performance at an attractive price. The true power of digital communication becomes apparent when measurements and adjustments can be made instantaneously. Digital modules provide the ability to diagnose and refine designs prior to final production, monitor and adjust running product and deliver exceptional thermal de-rating. Digital solutions combine voltage range accuracy while consuming less board space at competitive costs. The non-isolated DLynx family and the isolated Barracuda family offer both an industry-standard DOSA footprint to ensure hardware compatibility and a standard PMBus interface to ensure software compatibility to minimize risk for future designs.

DLynx
The DLynx portfolio is available in 3A, 6A, 12A, and 20A DOSA standards-based digital and analog versions in addition to a 40A module. The DC-DC POL converters efficiently power circuit board electronics such as processors, memory, application specific integrated circuits (ASICs), field programmable gate arrays (FPGAs) and other silicon devices. The standards-based DOSA footprints and analog/digital compatibility with existing circuit board designs shrinks the size, lowers the cost and improves the performance of DC-DC converter modules. An industry-standard PMBus interface and space-saving Tunable Loop technology deliver leading current density. With proven tools to simplify design, DLynx modules can be implemented with only three external components. Adaptive voltage scaling (AVS) leverages silicon performance to reduce power consumption through tight digital control (0.4 percent) of the output voltage and a 1 percent controller set point reference. See page 24 for specifications.

Barracuda
The cost-effective, high-efficiency Barracuda series delivers digital power communication and control in a quarter-brick and eighth-brick DOSA standard footprint. Power design engineers can deploy the new Barracuda modules in existing power designs as DOSA-compliant, drop-in upgrades for unregulated and semi-regulated bus converters. As part of the Total Efficiency architecture, the new Barracuda modules deliver peak efficiency of up to 96 percent. A new digital PMBus interface supports a wide range of commands to both control and monitor the Barracuda modules with a full range of protections and warnings, digital on/off, trim, margin, power good, rise time adjustment, and input under voltage lockout. See page 18 for specifications.

25

For product details, browse our website: ge.com/powerelectronics

Digital Power Solutions


Digital Power Insight Kit
The GE Energy Digital Power Insight (DPI) kit provides an easy to use digital evaluation set and GUI that gives power engineers a user interface that delivers control flexibility over their digital power converters. The software features continuous monitoring (polling) of input voltage, output voltage and current, as well as module status. Status changes are automatically time stamped and logged by the software and are easily exported. A Command Line Interface (CLI) is available for a more in-depth analysis of the transmitted data across the I2C bus. The CLI is a useful tool for creating and executing user-defined routines and scripts, in addition to logging of data for future review or plotting. The software enables engineers to create custom configuration files and to fine-tune and optimize a variety of parameters to ensure the highest levels of performance and efficiency. See www.digitalpowerinsight.com for more information. Design is simplified with GE Energy design tools like the Pro GUI, a graphical user interface package. During development, measurement of different power related parameters configurations allows the developer to optimize the design with a level of granularity and ease previously unavailable.

Digital DC-DC Efficiency Impact


Digital communication allows system architects to adjust critical system parameters to optimize overall efficiency and minimize power dissipation. The data collected may also be employed to improve reliability and total cost of ownership (TCO).

n=

Pout Pin

Pin - Pdiss Pin

Definition of System Efficiency

n = Performance Pin
Module efficiency alone is not the most significant variable. System efficiency is the real target for optimization. Performance may be TPC benchmarks, GFLOPs, etc.

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

26

Vertical Industry Solutions

GE Energy DC-DC isolated and point-of-load (POL) power solutions are used in thousands of applications across a broad array of global industries where discrete power solutions have traditionally been deployed: Aerospace and Aviation Displays, Lighting and Signage Industrial Automation and Process Control Instrumentation, Test and Measurement Medical Devices Robotics

Displays, Lighting and Signage


With the ever increasing demand for more efficient lighting solutions, LED lighting requires both constantvoltage and constant-current for its products. GE Energy power modules for lighting applications feature shielding from power disturbances, ruggedized designs, high efficiencies and high reliability in a small form factor. Outdoor Multimedia Displays Stadium Lighting Indoor and Outdoor Lighting Solar Lighting

Aerospace and Aviation


Electronics in the aviation industry are rapidly requiring increased capability and complexity while demanding a more compact design. Ranging from cockpit avionics and lighting systems to elaborate multimedia entertainment systems for commercial jets, the need for small, efficient, and reliable power electronics modules is critical. These new systems need a mixture of voltages and control frequencies. As design engineers continue to integrate more functionality into their innovative designs, the ability to support a complex mixture of output voltages will become even more important. Using standard, commercially available power supplies yields space savings, simpler designs, and less cabling when the DC output is fed directly into the backplane as opposed to using an external power supply. GE Energy power modules deliver the latest developments in power design in an efficient compact form factor. Cockpit Avionics Navigation Systems Aircraft Control Panels Lighting Systems In-Flight Entertainment (IFE)

Industrial Automation and Process Control

Industrial automation uses information technology and control systems to manage machinery and processes reducing the need for human intervention and possible costly errors. Power supplies for industrial automation and control applications require a wide operating temperature range and extended shock and vibration testing. GE Energy modules offer sequencing, reliability, and remote on/off facilities to ensure continuous efficient operation in the power design. Our ruggedized power supplies meet MIL STD 810F for extended shock and vibration testing, up to 50Grms, offer excellent thermal management up to 105C, and maintain low ripple/noise operation. Conveyor Systems Motor Control Applications Factory Automation (PLCs) Switching Systems Transportation / Railway Remote Monitoring Equipment Security Systems

27

For product details, browse our website: ge.com/powerelectronics

Vertical Industry Solutions


Instrumentation, Test and Measurement
Test and measurement systems are ubiquitous in electronic devices and maximize the productivity of engineers and technicians responsible for packaged-part characterization in applications ranging from early device research through development, quality verification, and failure analysis. Automated test equipment systems are routinely used in electronics manufacturing operations, the semiconductor industry, and factory environments. GE Energy power modules provide key features important to this market segment such as output voltage accuracy, low output noise, and ingress protection. In factory environments, improved cooling, extended temperature ranges, and ruggedization also prove to be important in considering power solutions. Semiconductor Test Equipment Automated Test Equipment Oscilloscopes Microscopes

Robotics
The global robotics industry is estimated to reach $21.4 billion US dollars by 2014 driven in part by demand from the auto and electronics markets. Power modules for robotics require a small form factor but a robust module to power their silicon processors and a variety of other electronics.

Power supplies for robotics applications require high levels of shock and vibration resistance and a wide operating temperature range. Manufacturing Systems Gantry Robots Industrial Robots

Medical Devices
Sophisticated power solutions for ultrasound, dialysis, and diagnostic equipment require stringent parameters such as low output ripple and EMI noise, which, if left unconditioned, can disrupt the performance and accuracy of the end equipment. These highly sensitive systems require more sophisticated power solutions a key strength for GE Energy. Given the sometimes long FDA approval cycles in the healthcare industry, our expertise in powering medical products provides solutions to complex system requirements which enable designers to improve product cycle times while reducing their time-to-market. Laboratory and Analytical Eye Care Equipment Medical Imaging Dental Equipment

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

28

Custom Capabilities

GE Global Research (GRC)


GE Global Research is one of the worlds most diversified industrial research labs, providing innovative technology for all of GEs businesses. Global Research has been the cornerstone of GE technology for more than 100 years, developing breakthrough innovations in areas such as medical imaging, energy generation technology, jet engines and lighting. GE Global Research is headquartered in Niskayuna, New York and has three other multidisciplinary facilities in Bangalore, India, Shanghai, China and Munich, Germany. We employ 2,800 researchers all searching to uncover the next technological breakthroughs that will change the landscape for the GE businesses. Our diverse set of technology expertise ranges from electronics to chemistry, biosciences to computing, metallurgy to fluid mechanics, materials to imaging and everything in between.

Our Customer Focus


GE Energy maintains a broad range of standard technologies that are the ideal building blocks to solve your applications power requirements. Many of our customers want us to re-package our technologies to develop an optimal solution that maximizes performance while reducing their total cost of ownership. We quickly and cost effectively employ our leadingedge technologies to deliver custom products that best fit our customers unique power requirementsreducing their risk and time to market by utilizing proven technologies.

Talent
GE Energy retains independent Research & Development and Custom Product Development teams to ensure both continued development of next generation technology road maps as well as custom / modified designs. We are selfcertified to support major safety agencies, further reducing product development schedules. Our regional Field Application Engineers (FAEs) work closely with our customers to rapidly produce clean engineering prototypes, and, along with our design teams, provide ongoing sales and technical support throughout the life of each application. Our closed-loop engineering processes ensure continued process improvements and new technology trends are implemented into our future designs.

29

For product details, browse our website: ge.com/powerelectronics

Custom Capabilities

Research & Design


GE Energy maintains strategic alliances with key suppliers and global industry leaders to help define future technology direction and objectives. Our alliances allow us greater utilization of next generation technologies and topologies that we deploy into our custom power designs to drive leading power densities and efficiencies for our customers.

Product Development
Once a solution is proven at the prototype level, our product development teams execute a full development process finalizing the design and implementing improvements to the fabricated parts (such as PCBs, sheet metal, and magnetics), confirming the bill of materials, defining the quality assurance metrics, performing design verification tests, performing reliability tests (HALT / STRIFE), and testing for certification and EMI / safety qualification.

Manufacturing & Quality Control


Our global operations and standardized processes enable us to build product at any of our global facilities utilizing consistent processes, equipment, training, and quality standards ensuring our customers receive exceptional product regardless of the country of design or manufacture. Our consistent approach ensures product quality, faster prototypes, and a reliable disaster recovery program.

Facilities
Our manufacturing strategy is to use the best of both internal and third party manufacturing, allowing us the flexibility to best fit each applications requirements. Our manufacturing processes, quality systems, data collection, and documentation are standardized across all facilities ensuring a smooth transition among locations to accommodate optimal capacity utilization and/or proximity of supply close to our end customers manufacturing location. Employing a global procurement strategy further underscores our commitment to our customers. Managing a common AVL across all divisions allows us to leverage our cost structure with our supplier base, which contributes to competitive products with cost savings for our customers.

Quality / Reliability
Our Global Total Quality Management System ensures consistent measurement and collection of SPC data and deployment of controls of operation. Starting with the design and development phase, we apply stringent derating criteria of components and expose our designs to STRIFE and HALT testing. Our focus on reliability continues into production by using HASS screening and elevated temperature testing. Finally, we monitor the process using CPK and statistical analysis tools, forming a closed-loop process. All of our facilities are ISO 9001:2000 and ISO14001 Certified with many of our Quality Managers holding Green and Black Belt Six Sigma ratings. As a leading power provider, we offer our customers low-risk, leading-edge technology and consistent, high-quality product produced around the world and backed up by responsive local support.

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

30

Engineering Resources & Tools

POL Voltage Setting & Tolerance Tool


Helps designers set the output voltage of POL modules including trim resistor values; worst case static variation in the output voltage for a trim resistor; calculating the values of margining resistors; and selecting the external series resistor to program the output voltage to desired nominal, low and high values.

Tunable LoopTM Selection Tool


The Tunable LoopTM helps designers select output capacitors, and values of CTUNE and RTUNE for Tunable LoopTM POLs for optimized performance and reduced output capacitance.

On-Line Power Module Selector


Helps select the best solutions to satisfy your power requirements. Simply provide your input range and output requirements. With this basic information, we provide a list of all possible solutions for side-by-side comparison with the ability to sort by size, efficiency and cost.

Power System Designer


With a little more application data such as maximum operating temperature, airflow and isolation, our Power System Designer can provide a complete engineering comparison for various architectures with block diagrams and product comparison charts (price, size and efficiency).

Evaluation Boards
Evaluation boards enable designers to evaluate the performance of our converters, either stand-alone or with our POL modules and optional input filters. Features such as on/off control, output voltage trim, and remote sense can be tested as well as external filtering components on both the input and output side.

Digital Power Insight Tools


Digital Power Insight software tools provide power engineers the flexibility to configure and reconfigure voltages, thresholds, warnings and settings for digital power modules using standards-based PMBus over I2C communications.

31

For product details, browse our website: ge.com/powerelectronics

The Company
Our History
The GE Energy Power Electronics business traces our nearly 100 year heritage of innovation to Bell Labs. We deliver reliable and intelligent power conversion solutions for cloud computing and mobile internet infrastructure with energy-efficient AC-DC power supplies, DC-DC circuit board mounted power modules, telecom energy systems, DC datacenters, and custom power products backed by local field expertise in 25+ locations worldwide. Designed for decades of nonstop operation, the high-availability Total Efficiency architecture DC power conversion solutions enable voice, video and data communications while assuring investment protection, total system efficiency, and significantly reduced total cost of ownership. Our customers include leading U.S. telecom service providers, such as AT&T, Verizon Wireless and Verizon, and leading global OEMs, such as Alcatel-Lucent, Cisco, Ericsson, Hewlett Packard, Huawei, Juniper Networks and Oracle. More information about our hardware, software, services and training is available at www.ge.com/powerelectronics.

OEM Embedded Power


GE Energys Power Electronics business offers end-to-end AC-DC and DC-DC power conversion solutions for Original Equipment Manufacturers (OEMs). We keep our customers ahead of their competitors by providing solutions that offer size, efficiency, and cost advantages while dramatically reducing risk through the utilization of proven, standards-based platforms. Our AC-DC custom power supply product line delivers custom, standard, and modified standard AC-DC frontends and rectifiers for datacom, telecom, medical, and industrial markets. Our personalized design assistance, sophisticated engineering, design flexibility, innovative solutions, and rapid prototype development distinguish us from our competitors and ensure we accelerate your time to market. Deep engineer-to-engineer relationships and our ability to optimize performance and reliability is balanced with cost sensitivity. We often act in a power consulting role enabling us to solve complex system issues beyond just the power supply. With 30+ years of technology leadership, our DC-DC circuit board mounted power product line has been designed to provide highly reliable DC-DC conversion solutions to a wide array of applications in telecom, servers, storage, industrial, medical, and military markets. These isolated and non-isolated board mounted power (BMP) modules address the markets ever-evolving demand for smaller size and greater efficiency at a lower cost of ownership. GE Energy was one of the cofounders of DOSA and remains an active leader in that continuous effort today to ensure that footprints and pin outs are compatible throughout the industry. Tunable Loop technology gives our customers a significant size and cost advantage over traditional capacitance designs.

Global Presence with offices around the world serving thousands of OEM Customers

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

32

Notes:

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

33

For product details, browse our website: ge.com/powerelectronics

Notes:

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

....................................................................................................................................................................................................................................................................................................................

For all inquiries, please call: +1 888 546 3243 or +1 972 244 9288

34

World Wide Headquarters GE Power Electronics, Inc. 601 Shiloh Road Plano, TX 75074 USA T: +1 972 244 WATT (9288) T: +1 888 546 3243 Tustin, CA Design Center T: +1.714.544 6665 pe.techsupportoem@ge.com

European Headquarters GE Power Electronics GmbH Bajuwarenring 5 82041 Oberhaching Germany T: +49 89 74423-206

Asia Pacific Headquarters GE Power Electronics (Shanghai) Co. Ltd. 3F, #9 Building, #456 Hong Cao Road Shanghai 200233, China T: +86.021.54279977*808 Beijing Office / T: +86.13910003797 Shenzhen Office / T: +86.135.1002.8510 Singapore Office / T: +65.6593.7200 Japan Office / T +81.3.5544.3927 Bangalore Office / T: +91 80 28411634 New Delhi Office / T: +91 11 2681 5457

GE Power Electronics reserves the right to make changes to the product(s) or imformation contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. 2012 GE Power Electronics, Inc. (Plano, TX) All International Rights Reserved. GE Power Electronics products are protected under various patents. Information on these patents is available at www.ge.com/powerelectronics

03/2012

You might also like