You are on page 1of 5

RFPO55 G.

8263
Specifications

1.0 Line 1.1 1.2 1.3 1.4

SPECIFICATION REFERENCES Parameter Part number Description RoHS compliant Package size Description M6163LF, iss. A (2013-02-27) - PROVISIONAL 12.8MHz MERC 14x9 HOT CMOS 3.3V Yes 14.6 mm x 9.7 mm x 6.2 mm

2.0 Line 2.1 2.2 2.3 2.4 2.5

FREQUENCY CHARACTERISTICS Parameter Nominal frequency Frequency calibration Reflow shift Temperature range Frequency stability over temperature range (in still air) Holdover stability, variable temperature (in still air) Holdover stability, constant temperature (in still air) Frequency slope (in still air) Free-run accuracy Supply voltage stability Load sensitivity Warm-up time Acceleration sensitivity Wander compliance At 25C2C, at time of shipment, reference to nominal frequency (note 1) After 1 hour recovery at 25C The operating temperature range over which the frequency stability is measured Reference to (Fmax+Fmin)/2 (note 1) Test Condition Value 12.8 0.5 max 1 max -40 to 85 20 max Unit MHz ppm ppm C ppb

2.6

T = 20C (note 1)

10 max

ppb pkpk ppb pkpk ppb/C ppm ppb ppb minutes ppb/g

2.7

24 hours (note 2)

1 max

2.8 2.9 2.10 2.11 2.12 2.13 2.14

Temperature ramp 0.5C/minute max. All causes, 20 years life, reference to nominal frequency 5% variation, reference to frequency at 3.3V, typical... 5pF variation, reference to frequency at 15pF, typical... Note 3, typically less than... Gamma vector of all three axes from 30 Hz to 1500 Hz, typically less than... G.8263 MTIE requirements met under minimum loop bandwidth of 0.05mHz (3200 second max time constant) under G.8263 (amendment) appendix IV temperature profile (20C excursion at 0.5C/min).

1 max 4.6 max 10 10 3 2

3.0 Line 3.1 3.2

FREQUENCY AGING Parameter Long term stability Long term stability Test Condition First year 20 years Value 1 max 3 max Unit ppm ppm

4.0 Line 4.1 4.2 4.3 4.4 4.5

ROOT ALLAN VARIANCE Parameter Root Allan Variance Root Allan Variance Root Allan Variance Root Allan Variance Root Allan Variance Test Condition Typical value at 25C, tau = 0.1s Typical value at 25C, tau = 1.0s Typical value at 25C, tau = 10s Typical value at 25C, tau = 100s Typical value at 25C, tau = 1000s Value 7 7 7 8 8 Unit E-11 E-11 E-11 E-11 E-11

Page 1

5.0 Line 5.1 5.2 5.3

POWER SUPPLY Parameter Supply voltage Input power Input power Test Condition 5% warm up, typical... Steady state in still air at 25C Value 3.3 1000 400 max Unit V mW mW

6.0 Line 6.1 6.2 6.3 6.4 6.5 6.6

HCMOS OSCILLATOR OUTPUT Parameter Output waveform Output voltage level low Output voltage level high Rise and fall times Duty cycle Output load Test Condition HCMOS Measured with a capacitive load of 15pF Measured with a capacitive load of 15pF Measured with a capacitive load of 15pF Measured at 50% level Nominal 10 max 90 min 4 max 45 to 55 15 %Vcc %Vcc ns % pF Value Unit

7.0 Line 7.1

SSB PHASE NOISE Parameter SSB phase noise power density at 1 Hz offset SSB phase noise power density at 10 Hz offset SSB phase noise power density at 100 Hz offset SSB phase noise power density at 1kHz offset SSB phase noise power density at 10kHz offset SSB phase noise power density at 100kHz offset SSB phase noise power density at 1MHz offset Test Condition Typical value at 25C Value -70 Unit dBc/Hz

7.2

Typical value at 25C

-98

dBc/Hz

7.3

Typical value at 25C

-125

dBc/Hz

7.4

Typical value at 25C

-143

dBc/Hz

7.5

Typical value at 25C

-152

dBc/Hz

7.6

Typical value at 25C

-155

dBc/Hz

7.7

Typical value at 25C

-156

dBc/Hz

8.0 Line 8.1

JITTER Parameter Jitter Test Condition RMS, 12kHz ~ 5MHz, typical... Value 0.6 Unit ps

Page 2

9.0 Line 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9

ENVIRONMENTAL Parameter Storage temperature Acceleration steady state Moisture sensitivity Temperature cycling Solder ability Humidity Shock Vibration RoHS IEC 60068-2-7 test Ga, 5000g, 10s (at peak acceleration), Y-axis only IPC/JEDEC J-STD-020, Class 1 IEC 60068-2-14 test Na, 400 cycles, -40C to +125C JESD 22-B102D, Method 2 Preconditioning 150C, 16 hours EIA/JEDEC22-A101, 85C/85%R.H., 1000 hours IEC 60068-2-27, test Ea; 1500g, 0.5ms, 18 shocks total IEC 60068-2-6, test Fc: 20g, 60 to 2000Hz 12 hours total Parts are fully compliant with the European Union directive 2002/95/EC on the restriction of t he use of certain hazardous substances in electrical and electronic equipment. Note parts are suitable for assembly using both Lead-free solders and Tin/Lead solders Test Condition Value -55 to 125 Unit C

10.0 Line 10.1 10.2 10.3 10.4 10.5 10.6

PIN CONNECTIONS Parameter Pin 1: Do Not Connect Pin 2: NC Pin 3: GND Pin 4: OUTPUT Pin 5: NC Pin 6: VCC For correct operation decouple the supply voltage with a 10 F capacitor close to the oscillator Description

11.0 Line 11.1 11.2 11.3 11.4 11.5

MARKING Parameter Type Line 1 Line 2 Line 3 Line 4 Description Laser marked RAKON Part number (Mxxxx) Frequency in MHz (xx.x MHz) Pin 1 identifier (dot), and date / location code (YYWWX)

12.0 Line 12.1 12.2

MANUFACTURING INFORMATION Parameter Reflow Packaging description Description IPC/JEDEC J-STD-020, Package reflow temperature for the Pb-Free process is 245C. The solder reflow process is as per the attached profile Tape and reel. 24mm wide tape and 330mm (13) reel. Standard packing quantity is 100 to 1000 units per reel

13.0 Line 13.1

SPECIFICATION NOTES Parameter Note 1 Description The characteristics of the component may be temporarily affected by the processes of assembly and soldering. The frequency specifications apply 48 hours after assembly. Nominal conditions apply unless otherwise stated After 60 days of continuous operation Time needed for frequency to be within 20 ppb reference to frequency after 1 hour, at 25C. Parameter is frequency, assembly and operating history dependent

13.2 13.3

Note 2 Note 3

14.0 Line 14.1

DISCLAIMER Parameter Disclaimer Description Samples supplied according to this specification are supplied from our development or preproduction programme and as such are not qualification approved products. No condition, warranty or representation regarding quality, suitability, performance, life or continuation of supply is given or implied and Guarantee in clause 6.1 of our standard Conditions of Sale is not applicable. The right is reserved to change the design or specification or cease supply without notice. RAKON UK Limited

Page 3

Drawing Name: RFPO50/55 Model Drawing

Page 5

Drawing Name: RFPO50 Series Reflow

Page 6

You might also like