You are on page 1of 8

ME2103 Quiz

Question Excerpt
1. A. B. C. D. 2. A. B. C. D. 3. A. B. C. D. What does A/F stand for? Across Flat Across Field Across Flange Across Fillet Name the type of manufacturing process indicated in the figure. Pyramid Knurling Diamond Knurling Cross Knurling Straight Knurling What does this symbol indicate? Cylindricity Straightness Parallelism Flatness

4. A. B. C. D. 5. A. B. C. D. 6. A. B. C. D. 7. A. B. C. D.

How many principal views does an object have? 2 4 6 8 How many classes of fit are provided for keys? 1 2 3 4 What type of fit does 6H/6g represent in screw threads? Medium Tight Close Free What type of fit does 5H/4h represent in screw threads? Medium Tight Close Free

8. A. B. C. D. 9. A. B. C. D.

What type of fit does 7H/8g represent in screw threads? Medium Tight Close Free Indicate the type of sectional view shown by the drawing: Offset section Aligned section Full section Half section

10. A. B. C. D.

Indicate the type of sectional view shown by the drawing: Offset section Irregular section Broken-out/Part section Removed section

11. A. B. C. D.

Indicate the type of dimension shown in the parenthesis: Overall dimension Auxiliary dimension Projection dimension Redundant dimension

12. A. B. C. D.

Choose the letter that indicates a dimension line a b c d

13. A. B. C. D.

Indicate the type of projection shown below: Auxiliary angle projection First angle projection Second angle projection Third angle projection

14. A. B. C. D.

Pitch Value Circumference Counterbore Countersunk

15.

What does 25 in M8x25 above mean?

A. B. C. D. 16. A. B. C. D. 17. A. B. C. D.

Pitch value Tolerance Diameter Thread length Bisecting an angle is to: divide the angle into 2 equal parts divide the angle into any 2 parts divide the angle into 10 degree intervals divide the angle into 1 degree intervals Continuous thin lines are used for: fictitious outlines and edges hidden outlines and edges visible outlines and edges cutting planes

18. A. B. C. D. 19. A. B. C. D.

2:1 on a drawing means: half size full size double full size two sizes To construct a pentagon, which of the following drawing instruments is not used? Compass French curve Ruler Pencil

20. When creating a multiview drawing of a design, which view must be first selected and oriented correctly as the first important step? A. Plan view B. Isometric view C. Front view D. Side view 21. A. B. C. D. 22. A. B. C. D. 23. A. B. C. D. What does the 'M' in M16x1.5-6H mean? Measured thread Man-made thread Metric thread Material thread In the dimensioning of screw threads what does the abbreviation LH stand for? Least Height Long Handle thread Left Headed thread Left Hand thread What is the type of fit shown in the diagram? Shaft basis fit Hole basis fit Clearance basis fit Inference basis fit

24. A. B. C. D.

Indicate the method of tolerancing shown below: Permitted tolerance Unilateral tolerance Bilateral tolerance Cumulative tolerance

25. A. B. C. D.

What is the limit tolerance (hole basis) shown in the figure below? Dia 50.000 - Dia 50.025 Dia 49.975 - Dia 49.991 Dia 49.984 - Dia 50.000 Dia 49.858 - Dia 49.920

26.

Which of the following indicates the cutting plane lines?

27.

Which of the following involving complicated hidden details is incorrect?

28. A. B. C. D. 29. A. B. C. D.

In a sectional view the following are not cross-hatched except: shaft rib pulley nut What does the abbreviation PCD stand for? Per circle dimension Pitch countersunk diameter Possible circle diameter Pitch circle diameter

30. A. B. C. D.

Which of the following abbreviation of general engineering terms is incorrect? A/C: Across corner DRG: Drawing CSK: Countersunk CBE: Counterbore

31. Name the type of coupling that will produce a non-uniform angular velocity at the output shaft when a uniform angular velocity is applied at the input shaft: A. Oldham coupling B. Flange coupling C. Spring coupling D. Hookes coupling 32. A. B. C. D. 33. A. B. C. D. 34. What are the 2 main types of locking devices? Slipping & Positive Frictional & Negative Frictional & Positive Slipping & Negative Name the type of coupling shown: Flange coupling Bolted coupling Hookes coupling Oldham coupling The correct illustration for the symbol shown is:

35.

Choose the correct symbol for:

36. A. B. C. D.

Pitch value Circumference Counterbore Countersunk

37. A. B. C. D.

What does 1.75 refer to? Pitch value Circumference Diameter Thread length

38.

You might also like