Professional Documents
Culture Documents
1 & 2 Pole - Low profile (15.7 mm height) 41.31 - 1 Pole 12 A (3.5 mm pin pitch) 41.52 - 2 Pole 8 A (5 mm pin pitch) 41.61 - 1 Pole 16 A (5 mm pin pitch) PCB mount - direct or via PCB socket 35 mm rail mount - via screw and screwless sockets DC coils - 400 mW 8 mm, 6 kV (1.2/50 s) isolation, coil-contacts Cadmium Free contact materials Flux proof: RT II standard, (RT III option)
41.31
41.52
41.61
FOR UL HORSEPOWER AND PILOT DUTY RATINGS SEE General technical information page V Contact specification Contact configuration Rated current/Maximum peak current Rated load AC1 Rated load AC15 (230 V AC) Single phase motor rating (230 V AC) Breaking capacity DC1: 30/110/220 V Minimum switching load Standard contact material Coil specification Nominal voltage (UN) Rated power AC/DC Operating range Holding voltage Must drop-out voltage Technical data Mechanical life AC/DC Electrical life at rated load AC1 Operate/release time cycles cycles ms V AC (50/60 Hz) V DC VA (50 Hz)/W AC DC AC/DC AC/DC A VA VA kW A Rated voltage/Maximum switching voltage V AC
1 CO (SPDT) 12/25 250/400 3,000 600 0.5 12/0.3/0.12 300 (5/5) AgNi 12 - 24 - 48 - 60 - 110 /0.4 (0.7...1.5)UN /0.4UN /0.1UN /30106 150 103 5/4 6 (8 mm) 1,000 40+85 RT II
2 CO (DPDT) 8/15 250/400 2,000 400 0.3 8/0.3/0.12 300 (5/5) AgNi 12 - 24 - 48 - 60 - 110 /0.4 (0.7...1.5)UN /0.4 UN /0.1 UN /30106 80 103 5/4 6 (8 mm) 1,000 40+85 RT II
1 CO (SPDT) 16/30 250/400 4,000 750 0.5 16/0.3/0.12 300 (5/5) AgNi 12 - 24 - 48 - 60 - 110 /0.4 (0.7...1.5)UN /0.4 UN /0.1 UN /30106 70 103 5/4 6 (8 mm) 1,000 40+85 RT II
mW (V/mA)
Insulation between coil and contacts (1.2/50 s) kV Dielectric strength between open contacts V AC Ambient temperature range Environmental protection Approvals (according to type) C
41.81 - 9024
41.81 - 8240
Copper side view Output circuit Contact configuration Rated current/Maximum peak current (100 s)A Rated voltage/Maximum blocking voltage Switching voltage range Minimum switching current Max. OFF-state leakage current Max. ON-state voltage drop Input circuit Nominal voltage Operating range Control current Release voltage Impedance Technical data Operate/release time Dielectric strength between input/output Ambient temperature range Environmental protection Approvals (according to type) ms V C 0.05/0.25 2,500 20...+60 RT III V DC V DC mA V DC 24 10...32 9 9 2,600 V V mA mA V 1 NO (SPST-NO) 5/40 (24/35)DC (1.5...35)DC 1 0.01 0.3
1 NO (SPST-NO) 3/40 (240/275)AC (12...275)AC 50 1 1.1 24 10...32 9 9 2,600 10/10 2,500 20...+60 RT III
4 1 . 5
Series Type 3 = PCB - 3.5 mm pinning 5 = PCB - 5 mm pinning 6 = PCB - 5 mm pinning No. of poles 1 = 1 pole for 41.31, 12 A 41.61, 16 A 2 = 2 pole for 41.52, 8 A Coil version 9 = DC Coil voltage See coil specifications
2 . 9 . 0 2 4 . 0
0
D: Special versions 0 = Flux proof (RT II) 1 = Wash tight (RT III) C: Options 1 = None
A: Contact material 0 = Standard AgNi 4 = AgSnO2 5 = AgNi + Au (5 m) B: Contact circuit 0 = CO (nPDT) 3 = NO (nPST)
Selecting features and options: only combinations in the same row are possible. Preferred selections for best availability are shown in bold. Type 41.31 41.52 41.61 Coil version DC DC DC A 0-4-5 0-5 0-4 B 0-3 0-3 0-3 C 1 1 1 D 0-1 0-1 0-1
Solid state relay (SSR) Example: 41 series SSR relay, 5 A output, 24 V DC supply.
4 1 . 8
Series Type 8 = SSR type Output 1 = 1 NO (SPST-NO) Input circuit See input specifications
1 . 7 . 0 2 4 . 9 0 2 4
Output circuit 9024 = 5 A - 24 V DC 8240 = 3 A - 240 V AC
single contact
DC voltage (V)
When switching a resistive load (DC1) having voltage and current values under the curve, an electrical life of 100103 can be expected. In the case of DC13 loads, the connection of a diode in parallel with the load will permit a similar electrical life as for a DC1 load. Note: the release time for the load will be increased.
Coil specifications
DC coil data Nominal voltage UN V 12 24 48 60 110 Coil code Operating range Umin V 8.4 16.8 33.6 42 77 Umax V 18 36 72 90 165 Resistance Rated coil consumption R I at UN mA 360 33.3 1,440 16.7 5,760 8.3 9,000 6.6 24,200 4.5 R 41 - DC coil operating range v ambient temperature
1 - Max. permitted coil voltage. 2 - Min. pick-up voltage with coil at ambient temperature.
Input specification
Input data - DC types Nominal voltage UN V 24 Input code Operating range Umin V 10 Umax V 32 Release voltage V 9 Impedance Control current I at UN mA 9
7.024
2,600
Output specification
L 41 - Output current v ambient temperature SSR - 5 A DC output types L 41 - Output current v ambient temperature SSR - 3 A AC output types
Output current
Output current
Socket type
93.02
41.52.9.005.0010 93.02.0.024 41.52.9.012.0010 93.02.0.024 41.52.9.024.0010 93.02.0.024 41.52.9.060.0010 93.02.0.060 41.52.9.110.0010 93.02.0.125 41.52.9.110.0010 93.02.0.240 41.52.9.005.0010 93.02.7.024 41.52.9.012.0010 93.02.7.024 41.52.9.024.0010 or 41.81.7.024.xxxx 93.02.7.024 41.52.9.048.0010 93.02.7.060 41.52.9.060.0010 93.02.7.060 093.08 (see specification next page) 093.01 (see specification next page) 090.72 (see specification next page) 10 A - 250 V 6 kV (1.2/50 s) between coil and contacts IP 20 C (40+70)C - (UN 60 V DC), (40+55)C - (UN > 60 V DC) Nm 0.5 mm 8 solid wire stranded wire mm2 1x6 / 2x2.5 AWG 1x10 / 2x14 1x4 / 2x2.5 1x12 / 2x14
Socket type
93.52
41.52.9.005.0010 93.52.0.024 41.52.9.012.0010 93.52.0.024 41.52.9.024.0010 93.52.0.024 41.52.9.060.0010 93.52.0.060 41.52.9.110.0010 93.52.0.125 41.52.9.110.0010 93.52.0.240 41.52.9.005.0010 93.52.7.024 41.52.9.012.0010 93.52.7.024 41.52.9.024.0010 or 41.81.7.024.xxxx 93.52.7.024 41.52.9.048.0010 93.52.7.060 41.52.9.060.0010 93.52.7.060 093.08 (see table below) 093.01 (see table below) 090.72 (see table below) 10 A - 250 V 6 kV (1.2/50 s) between coil and contacts IP 20 (40+70)C - (UN 60 V DC), (40+55)C - (UN > 60 V DC) 8 solid wire 1x2.5 1x14 stranded wire 1x2.5 1x14
C mm mm2 AWG
Accessories
8-way jumper link for 93.02 and 93.52 sockets Rated values
093.08
093.08.0 (black)
093.01
093.01
Thickness 2 mm, required at the start and the end of a group of interfaces. Can be used for visual separation group, must be used for: - protective separation of different voltages of neighbouring PLC interfaces according to VDE 0106-101 - protection of cut jumper links Sheet of marker tags for 38.x2, plastic, 72 tags, 6x12 mm 060.72
060.72 8
95.13.2
95.15.2
* For currents >10 A, contact terminals must be connected in parallel (21 with 11, 24 with 14, 22 with 12). (1) With the relay 41.81 the NO change-over contact will be 11-14.
41.31
13 7.5
41.52
41.81 - 9024
30 20
3.5
3.5
95.13.2
1.5
41.61
Packaging codes
How to code and identify retaining clip and packaging options for sockets. Example:
9 5 . 1
3 . 2
S L
A
A Standard packaging
9 5 . 1
3 . 2