You are on page 1of 45

MCP6PB M2+ Setup Manual

FCC Information and Copyright


This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation.

The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand. Duplication of this publication, in part or in whole, is not allowed without first obtaining the vendors approval in writing.

The content of this users manual is subject to be changed without notice and we will not be responsible for any mistakes found in this users manual. All the brand and product names are trademarks of their respective companies.

Table of Contents Chapter 1: Introduction ........................................ 1


1.1 1.2 1.3 1.4 1.5 2.1 2.2 2.3 2.4 3.1 3.2 4.1 4.2 4.3 5.1 5.2 5.3 5.4 5.5 Before You Start ................................................................................ 1 Package Checklist ............................................................................. 1 Motherboard Features...................................................................... 2 Rear Panel Connectors ..................................................................... 3 Motherboard Layout......................................................................... 4 Installing Central Processing Unit (CPU) ....................................... 5 FAN Headers ...................................................................................... 7 Installing System Memory ................................................................ 8 Connectors and Slots ....................................................................... 10 How to Setup Jumpers .................................................................... 12 Detail Settings .................................................................................. 12 Operating System............................................................................ 19 Raid Arrays ...................................................................................... 19 How RAID Works ............................................................................. 19 Driver Installation Note.................................................................. 21 Software ............................................................................................ 22 Award BIOS Beep Code .................................................................. 23 Extra Information............................................................................ 23 Troubleshooting ............................................................................... 24

Chapter 2: Hardware Installation .......................... 5

Chapter 3: Headers & Jumpers Setup .................. 12 Chapter 4: RAID Functions .................................. 19

Chapter 5: Useful Help ........................................ 21

Appendix: SPEC In Other Languages ................... 26


German .................................................................................................................. 26 French .................................................................................................................... 28 Italian ..................................................................................................................... 30 Spanish ................................................................................................................... 32 Portuguese ............................................................................................................ 34 Polish ...................................................................................................................... 36 Russian ................................................................................................................... 38 Arabic..................................................................................................................... 40 Japanese ................................................................................................................ 42

MCP6PB M2+

CHAPTER 1: INTRODUCTION 1.1


BEFORE YOU START


Prepare a dry and stable working environment with sufficient lighting. Always disconnect the computer from power outlet before operation. Before you take the motherboard out from anti-static bag, ground yourself properly by touching any safely grounded appliance, or use grounded wrist strap to remove the static charge. Avoid touching the components on motherboard or the rear side of the board unless necessary. Hold the board on the edge, do not try to bend or flex the board. Do not leave any unfastened small parts inside the case after installation. Loose parts will cause short circuits which may damage the equipment. Keep the computer from dangerous area, such as heat source, humid air and water.

Thank you for choosing our product. Before you start installing the motherboard, please make sure you follow the instructions below:

1.2

PACKAGE CHECKLIST
IDE Cable X 1 Serial ATA Cable X 1 Rear I/O Panel for ATX Case X 1 Installation Guide X 1 Fully Setup Driver CD X 1 (full version manual files inside) FDD Cable X 1 (optional) USB 2.0 Cable X1 (optional) Serial ATA Power Cable X 1 (optional)

Note: The package contents may be differed by area or your motherboard version.

Motherboard Manual

1.3

MOTHERBOARD FEATURES
SPEC Socket AM2 / AM2+ AMD 64 Architecture enables 32 and 64 bit computing Supports Hyper Transport and PowerNow

CPU

AMD Athlon 64 / Athlon 64 FX / Athlon 64 x2 / Sempron / PhenomX3 / X4 processors (Maximum Watt: 95W)

FSB Chipset

Support HyperTransport 1.0 Ghz Supports up to 2 GT/s Bandwidth GeForce 6150SE ITE 8718F Low Pin Count Interface Environment Control initiatives H/W Monitor ITE's "Smart Guardian" function Dual Channel Mode DDR2 memory module Supports DDR2 533 / 667 / 800 Supports DDR2 1066 (by AM2+ CPU) Registered DIMM and ECC DIMM is not supported Max Shared Video Memory is 256MB Ultra DMA 33 / 66 / 100 / 133 Bus Master Mode supports PIO Mode 0~4, Data transfer rates up to 3 Gb/s SATA Version 2.0 specification compliant 10 / 100 Mb/s auto negotiation Half / Full duplex capability 5.1 channels audio out High Definition Audio x1 x1 x1 x1 x2 x1 x1 Supports PCI-E x16 expansion cards Supports PCI expansion cards Each connector supports 2 Floppy drives Each connector supports 2 IDE device Each connector supports 1 SATA devices Supports front panel facilities Supports front panel audio function

Super I/O

Provides the most commonly used legacy Super I/O functionality DDR2 DIMM Slots x 2

Main Memory

Max Memory Capacity 4GB Each DIMM supports 256MB/512MB/ 1GB/2GB DDR2

Graphics IDE

Integrated in GeForce 6150SE Chipset Integrated IDE Controller

SATA II

Integrated Serial ATA Controller

LAN

Realtek RTL 8201CL PHY

Sound

ALC662 PCI Express x16 slot PCI slot Floppy connector IDE Connector SATA Connector Front Panel Connector Front Audio Connector

Slots On Board Connector

MCP6PB M2+
SPEC CPU Fan header System Fan header CMOS clear header USB connector Power Connector (24pin) Power Connector (4pin) Printer Port Connector Serial port Connector PS/2 Keyboard PS/2 Mouse Back Panel VGA port I/O LAN port USB Port Audio Jack Board Size Special Features 170 mm(W) x 235 mm(L) RAID 0 / 1 Biostar Reserves the right to add or remove support for any OS With or without notice. x1 x1 x1 x2 x1 x1 x1 x1 x1 x1 x1 x1 x4 x3 CPU Fan power supply (with Smart Fan function) System Fan Power supply Restore CMOS data to factory default Each connector supports 2 front panel USB ports Connects to Power supply Connects to Power supply Each connector supports 1 Printer port Connects to RS-232 Port Connects to PS/2 Keyboard Connects to PS/2 Mouse Connect to D-SUB monitor Connect to RJ-45 ethernet cable Connect to USB devices Provide Audio-In/Out and microphone connection MicroATX

OS Support Windows XP / Vista / 7

1.4
PS/2 Mouse

REAR PANEL CONNECTORS


LAN Line In/ Sur round Line Out Mic I n 1/ Bass/ Cent er

PS/ 2 Keyboard

VGA

USBX2

USBX2

Motherboard Manual

1.5

MOTHERBOARD LAYOUT
JKBMS

J KB_PWR J ATXPWR2

D IM M A1

JUSB1

JCFAN JUSBPWR1

D IM M B1

S ock et A M 2+

J ATXPWR1

JUSBLAN1

JAUDIO1

GeForce 6150SE
J USBPWR2
JU S B3

BAT1
LAN

JCOM JUSB2

JCMOS1

PEX16_1

BIOS

Super I/O
JPRNT

FDD
JAUDIOF

Codec

PCI1

SATA2 JSFAN

SATA1 J PANEL1

Note: represents the 1st pin.

ID E

JVG A

MCP6PB M2+

CHAPTER 2: HARDWARE INSTALLATION 2.1 INSTALLING CENTRAL PROCESSING UNIT (CPU)

Step 1: Remove the socket protection cap.

Step 2: Pull the lever toward direction A from the socket and then raise the lever up to a 90-degree angle.

Step 3: Look for the white triangle on socket, and the gold triangle on CPU should point towards this white triangle. The CPU will fit only in the correct orientation.

Motherboard Manual Step 4: Hold the CPU down firmly, and then close the lever toward direct B to complete the installation.

Step 5: Put the CPU Fan on the CPU and buckle it. Connect the CPU FAN power cable to the JCFAN. This completes the installation.

Note: Please update the BIOS to the latest version while using AM2+ CPUs. Due to the latest CPU transition, you may encounter the situation that the new system failed to boot while using new AM2+ CPUs. In this case, please install one standard AM2 CPU to boot your system, and update the latest BIOS from our website for AM2+ CPUs support.

MCP6PB M2+

2.2

FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan cable and connector may be different according to the fan manufacturer. Connect the fan cable to the connector while matching the black wire to pin#1.

JCFAN: CPU Fan Header

1 4

Pin 1 2 3 4

Assignment Ground +12V FAN RPM rate sense Smart Fan Control (By Fan)

JSFAN: System Fan Header

Pin 1 2 3

Assignment Ground +12V FAN RPM rate sense

Note:
The JCFAN supports 4-pin head connector; the JSFAN, 3-pin head connector. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin#2, and the black wire is Ground and should be connected to GND.

Motherboard Manual

2.3

INSTALLING SYSTEM MEMORY

A. Memory Modules

1.

Unlock a DIMM slot by pressing the retaining clips outward. Align a DIMM on the slot so that the notch on the DIMM matches the break on the Slot.

2.

Insert the DIMM vertically and firmly into the slot until the retaining chip snap back in place and the DIMM is properly seated.

D IM M A 1 D IM M B 1

MCP6PB M2+

B. Memory Capacity
DIMM Socket Location DIMMA1 DIMMB1 DDR2 Module 256MB/512MB/1GB/2GB 256MB/512MB/1GB/2GB Total Memory Size Max is 4GB.

C. Dual Channel Memory installation


To trigger the Dual Channel function of the motherboard, the memory module must meet the following requirements: Install memory module of the same density in pairs, shown in the following table. Dual Channel Status Disabled Disabled Enabled DIMMA1 O X O DIMMB1 X O O

(O means memory installed, X means memory not installed.) The DRAM bus width of the memory module must be the same (x8 or x16)

Motherboard Manual

2.4

CONNECTORS AND SLOTS


The motherboard provides a standard floppy disk connector that supports 360K, 720K, 1.2M, 1.44M and 2.88M floppy disk types. This connector supports the provided floppy drive ribbon cable.

FDD: Floppy Disk Connector

2 1

34 33

IDE: IDE/ATAPI Connector


The motherboard has a 32-bit Enhanced PCI IDE Controller that provides PIO Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 functionality. The IDE connector can connect a master and a slave drive, so you can connect up to two drives.

40

39

10

MCP6PB M2+

PEX16_1: PCI-Express Gen2 x16 Slot


PCI-Express 1.0a compliant. Maximum theoretical realized bandwidth of 4GB/s simultaneously per direction, for an aggregate of 8GB/s totally. PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins. 2X bandwidth over the traditional PCI architecture.

PEX16_1

PCI1: Peripheral Component Interconnect Slot


This motherboard is equipped with 1 standard PCI slot. PCI stands for Peripheral Component Interconnect, and it is a bus standard for expansion cards. This PCI slot is designated as 32 bits.

PCI1

11

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP 3.1 HOW TO SETUP JUMPERS


The illustration shows how to set up jumpers. When the jumper cap is placed on pins, the jumper is close, if not, that means the jumper is open.

Pin opened

Pin closed

Pin1-2 closed

3.2

DETAIL SETTINGS
This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, Sleep, and speaker connection. It allows user to connect the PC cases front panel switch functions.
PWR_LED On/Off
9 1

JPANEL1: Front Panel Header

++ + SPK

16 8

RST HLED

Pin 1 2 3 4 5 6 7 8

Assignment +5V N/A N/A Speaker HDD LED (+) HDD LED (-) Ground Reset control

Function Speaker Connector Hard drive LED Reset button

Pin 9 10 11 12 13 14 15 16

Assignment N/A N/A N/A Power LED (+) Power LED (+) Power LED (-) Power button Ground

Function N/A N/A Power LED Power-on button

12

MCP6PB M2+

JATXPWR1: ATX Power Source Connector


This connector allows user to connect 24-pin power connector on the ATX power supply.
12 24

1
Pin 13 14 15 16 17 18 19 20 21 22 23 24 Assignment +3.3V -12V Ground PS_ON Ground Ground Ground NC +5V +5V +5V Ground Pin 1 2 3 4 5 6 7 8 9 10 11 12

13
Assignment +3.3V +3.3V Ground +5V Ground +5V Ground PW_OK Standby Voltage+5V +12V +12V +3.3V

JATXPWR2: ATX Power Source Connector


By connecting this connector, it will provide +12V to CPU power circuit.

4 1

3 2
Pin 1 2 3 4 Assignment +12V +12V Ground Ground

Note:
Before power on the system, please make sure that both JATXPWR1 and JATXPWR2 connectors have been plugged-in. 13

Motherboard Manual

JUSB2/JUSB3: Headers for USB 2.0 Ports at Front Panel


These headers allow user to connect additional USB cable on the PC front panel, and also can be connected with internal USB devices, like USB card reader.
Pin 1 2 3 4 5 6 7 8 9 10 Assignment +5V (fused) +5V (fused) USBUSBUSB+ USB+ Ground Ground NC Key

JU SB2 JU SB3 10 2 9 1

SATA1/SATA2: Serial ATA Connectors


The motherboard has a PCI to SATA Controller with 2 channels SATA interface, it satisfies the SATA 2.0 spec and with transfer rate of 3.0Gb/s.

SATA2 SATA1

Pin 1 2 3 4 5 6 7

Assignment Ground TX+ TXGround RXRX+ Ground

14

MCP6PB M2+

JAUDIOF: Front Panel Audio Header


This header allows user to connect the front audio output cable with the PC front panel. This header allows only HD audio front panel connector; AC97 connector is not acceptable.
Pin 1 2 3 4 5 6 7 8 9 10 Assignment Mic Left in Ground Mic Right in GPIO Right line in Jack Sense Front Sense Key Left line in Jack Sense

2 1

10 9

JCOM: Serial port Connector


The motherboard has a Serial Port Connector for connecting RS-232 Port.
Pin 1 2 3 4 5 6 7 8 9 10 Assignment Carrier detect Received data Transmitted data Data terminal ready Signal ground Data set ready Request to send Clear to send Ring indicator NC

2 1

10 9

15

Motherboard Manual

JCMOS1: Clear CMOS Header


By placing the jumper on pin2-3, it allows user to restore the BIOS safe setting and the CMOS data, please carefully follow the procedures to avoid damaging the motherboard.
3 1

Pin 1-2 Close: Normal Operation (default).

3
3 1

Pin 2-3 Close: Clear CMOS data.

Clear CMOS Procedures:


1. 2. 3. 4. 5. 6. Remove AC power line. Set the jumper to Pin 2-3 close. Wait for five seconds. Set the jumper to Pin 1-2 close. Power on the AC. Reset your desired password or clear the CMOS data.

16

MCP6PB M2+

JPRNT: Printer Port Connector


This header allows you to connect printer port on the PC.
2 1 25

Pin 1 2 3 4 5 6 7 8 9 10 11 12 13

Assignment -Strobe -ALF Data 0 -Error Data 1 -Init Data 2 -Scltin Data 3 Ground Data 4 Ground Data 5

Pin 14 15 16 17 18 19 20 21 22 23 24 25 26

Assignment Ground Data 6 Ground Data 7 Ground -ACK Ground Busy Ground PE Ground SCLT Key

17

Motherboard Manual

JUSBPWR1/JUSBPWR2: Power Source Headers for USB Ports


Pin 1-2 Close: JUSBPWR1: +5V for USB ports at JUSB1/JUSBLAN1. JUSBPWR2: +5V for USB ports at front panel (JUSB2/JUSB3). Pin 2-3 Close: JUSBPWR1: +5V STB for USB ports at JUSB1/JUSBLAN1. JUSBPWR2: +5V STB for USB ports at front panel (JUSB2/JUSB3).

JUSBPWR1
1 3 3 1

3
Pin 1-2 close

1 3
Pin 2-3 close

JUSBPWR2

JKB_PWR: Power Source Header for PS/2 Keyboard and Mouse


1
1 3

Pin 1-2 close +5V for PS/2 keyboard and mouse.

Pin 2-3 close +5V STB for PS/2 keyboard and mouse.

18

MCP6PB M2+

CHAPTER 4: RAID FUNCTIONS 4.1 4.2 OPERATING SYSTEM RAID ARRAYS


Supports Windows XP and Windows Vista.

RAID supports the following types of RAID arrays: RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for many applications. RAID 1: RAID 1 defines techniques for mirroring data.

4.3

HOW RAID WORKS

RAID 0:
The controller stripes data across multiple drives in a RAID 0 array system. It breaks up a large file into smaller blocks and performs disk reads and writes across multiple drives in parallel. The size of each block is determined by the stripe size parameter, which you set during the creation of the RAID set based on the system environment. This technique reduces overall disk access time and offers high bandwidth.

Features and Benefits


Drives: Minimum 2, and maximum is up to 6 or 8. Depending on the platform. Uses: Intended for non-critical data requiring high data throughput, or any environment that does not require fault tolerance. Benefits: provides increased data throughput, especially for large files. No capacity loss penalty for parity. Drawbacks: Does not deliver any fault tolerance. If any drive in the array fails, all data is lost. Fault Tolerance: No.

Block 1 Block 3 Block 5

Block 2 Block 4 Block 6

19

Motherboard Manual

RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1 array system. The mirrored (backup) copy of the data can reside on the same disk or on a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the active volume or drive is corrupted or becomes unavailable because of a hardware failure. RAID techniques can be applied for high-availability solutions, or as a form of automatic backup that eliminates tedious manual backups to more expensive and less reliable media.

Features and Benefits


Drives: Minimum 2, and maximum is 2. Uses: RAID 1 is ideal for small databases or any other application that requires fault tolerance and minimal capacity. Benefits: Provides 100% data redundancy. Should one drive fail, the controller switches to the other drive. Drawbacks: Requires 2 drives for the storage space of one drive. Performance is impaired during drive rebuilds. Fault Tolerance: Yes.

Block 1 Block 2 Block 3

Block 1 Block 2 Block 3

20

MCP6PB M2+

CHAPTER 5: USEFUL HELP 5.1 DRIVER INSTALLATION NOTE


After you installed your operating system, please insert the Fully Setup Driver CD into your optical drive and install the driver for better system performance. You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system. Note:
If this window didnt show up after you insert the Driver CD, please use file browser to locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will list the compatible driver for your motherboard and operating system. Click on each device driver to launch the installation program.

B. Software Installation
To install the software, please click on the Software icon. The setup guide will list the software available for your system, click on each software title to launch the installation program.

C. Manual
Aside from the paperback manual, we also provide manual in the Driver CD. Click on the Manual icon to browse for available manual. Note:
You will need Acrobat Reader to open the manual file. Please download the latest version of Acrobat Reader software from http://www.adobe.com/products/acrobat/readstep2.html 21

Motherboard Manual

5.2

SOFTWARE

Installing Software
1. Insert the Setup CD to the optical drive. The drivers installation program would appear if the Autorun function has been enabled. 2. Select Software Installation, and then click on the respective software title. 3. Follow the on-screen instructions to complete the installation.

BIOScreen Utility
This utility allows you to personalize your boot logo easily. You can choose JPG or BMP as your boot logo so as to customize your computer.

Please follow the following instructions to update boo logo: 1. Load Image Choose the picture as the boot logo. 2. Transform Transform the picture for BIOS and preview the result.
3. 22

Update Bios Write the picture to BIOS Memory to complete the update.

MCP6PB M2+

5.3

AWARD BIOS BEEP CODE


Beep Sound Meaning Video card not found or video card memory bad CPU overheated System will shut down automatically No error found during POST No DRAM detected or install

One long beep followed by two short beeps High-low siren sound One Short beep when system boot-up Long beeps every other second

5.4

EXTRA INFORMATION
If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again. In this case, please double check: 1. The CPU cooler surface is placed evenly with the CPU surface. 2. CPU fan is rotated normally. 3. CPU fan speed is fulfilling with the CPU speed. After confirmed, please follow steps below to relief the CPU protection function. 1. Remove the power cord from power supply for seconds. 2. Wait for seconds. 3. Plug in the power cord and boot up the system. Or you can: 1. Clear the CMOS data. (See Close CMOS Header: JCMOS1 section) 2. Wait for seconds. 3. Power on the system again.

CPU Overheated

23

Motherboard Manual

5.5
1.

TROUBLESHOOTING
Probable Solution 1. 2. 3. Make sure power cable is securely plugged in. Replace cable. Contact technical support.

There is no power in the system. Power LED does not shine; the fan of the power supply does not work 2. Indicator light on keyboard does not shine. System is inoperative. Keyboard lights are on, power indicator lights are lit, and hard drives are running. System does not boot from a hard disk drive, but can be booted from optical drive.

Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. 1. Check cable running from disk to disk controller board. Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. 2. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. System only boots from an optical 1. Back up data and applications drive. Hard disks can be read, files. applications can be used, but system 2. Reformat the hard drive. fails to boot from a hard disk. Re-install applications and data using backup disks. Screen message shows Invalid Review systems equipment. Make sure Configuration or CMOS Failure. correct information is in setup. System cannot boot after user installs a 1. Set master/slave jumpers second hard drive. correctly. 2. Run SETUP program and select correct drive types. Call the drive manufacturers for compatibility with other drives.

24

MCP6PB M2+

This page is intentionally left blank.

25

Motherboard Manual

APPENDIX: SPEC IN OTHER LANGUAGES GERMAN


Spezifikationen Sockel AM2 / AM2+ Die AMD 64-Architektur untersttzt eine 32-Bit- und AMD Athlon 64 / Athlon 64 FX / Althlon 64 CPU X2 / Sempron / PhenomX3 / X4 Untersttzt Hyper Transport und PowerNow Prozessoren (Maximales Watt: 95W) Untersttzt HyperTransport 2.0 Ghz mit FSB einer Bandbreite von bis zu 4 GT/s Chipsatz GeForce 6150SE Low Pin Count-Schnittstelle ITE8716F Umgebungskontrolle, Super E/A Bietet die hufig verwendeten alten Super Hardware-berwachung E/A-Funktionen. "Smart Guardian"-Funktion von ITE Dual-Kanal DDR2 Speichermodul DDR2 DIMM-Steckpltze x 2 Untersttzt DDR2 533 / 667 / 800 Arbeitsspeich Max. 4GB Arbeitsspeicher Untersttzt DDR2 1066 (by AM2+ CPU) er Jeder DIMM untersttzt 256MB/512MB/ registrierte DIMMs. ECC DIMMs werden nicht 1GB/2GB DDR2. untersttzt. Grafik Integrierter GeForce 6150SE-Chipsatz Max. 256 MB gemeinsam benutzter Videospeicher Ultra DMA 33 / 66 / 100 / 133 Bus Master-Modus IDE Integrierter IDE-Controller Untersttzt PIO-Modus 0~4, Datentransferrate bis zu 3 Gb/s SATA Integrierter Serial ATA-Controller Konform mit der SATA-Spezifikation Version 2.0. 10 / 100 Mb/s Auto-Negotiation LAN Realtek RTL 8201CL PHY Halb-/ Vollduplex-Funktion HD 5.1-Kanal-Audioausgabe Audio-Unters ALC662 Untersttzt High-Definition Audio ttzung 64-Bit-Datenverarbeitung

26

MCP6PB M2+
Spezifikationen Steckpltze PCI Express x16 Steckplatz PCI-Steckplatz Diskettenlaufwerkanschluss IDE-Anschluss SATA-Anschluss Fronttafelanschluss Front-Audioanschluss CPU-Lfter-Sockel Onboard-Ans chluss System-Lfter-Sockel "CMOS lschen"-Sockel USB-Anschluss Stromanschluss (24-polig) Stromanschluss (4-polig) Druckeranschluss Anschluss Serieller Anschluss PS/2-Tastatur PS/2-Maus Rckseiten-E VGA-Anschluss /A LAN-Anschluss USB-Anschluss Audioanschluss Platinengr e Sonderfunkti onen OS-Unterst tzung Untersttzt RAID 0 / 1 Biostar behlt sich das Recht vor , ohne Ankndigung Windows XP / Vista / 7 die Untersttzung fr ein Betriebssystem hinzuzufgen oder zu entfernen. 170 mm (B) X 235 mm (L) x1 x1 x2 x1 x1 x1 x1 x1 x1 x1 x1 x4 x3 Jeder Anschluss untersttzt 1 Druckeranschluss Jeder Anschluss untersttzt 2 Fronttafel-USB-Anschlsse x1 x1 x1 x1 x2 x1 x1 x1 Jeder Anschluss untersttzt 2 Diskettenlaufwerke Jeder Anschluss untersttzt 2 IDE-Laufwerke Jeder Anschluss untersttzt 1 SATA-Laufwerk Untersttzt die Fronttafelfunktionen Untersttzt die Fronttafel-Audioanschlussfunktion CPU-Lfterstromversorgungsanschluss (mit Smart Fan-Funktion) System-Lfter-Stromversorgungsanschluss

27

Motherboard Manual

FRENCH
SPEC Socket AM2 / AM2+ UC Processeurs AMD Athlon 64 / Athlon 64 FX L'architecture AMD 64 permet le calcul 32 et 64 bits / Althlon 64 X2 / Sempron / PhenomX3 / Prend en charge Hyper Transport et PowerNow X4 (Watt maximum : 95W) Bus frontal Chipset Prend en charge Hyper Transport 2.0 Ghz jusqu' une bande passante de 4 GT/s GeForce 6150SE ITE 8718F Super E/S Fournit la fonctionnalit de Super E/S patrimoniales la plus utilise. Interface faible compte de broches Initiatives de contrle environnementales, Moniteur de matriel Fonction "Gardien intelligent" de l'ITE Module de mmoire DDR2 mode double voie Prend en charge la DDR2 533 / 667 / 800 Prend en charge la DDR2 1066 (by AM2+ CPU) Les DIMM registres et DIMM avec code correcteurs d'erreurs ne sont pas prises en charge Mmoire vido partage maximale de 512 Mo Mode principale de Bus Ultra DMA 33 / 66 / 100 / 133 Prend en charge le mode PIO 0~4, Taux de transfert jusqu' 3 Go/s. Conforme la spcification SATA Version 2.0 10 / 100 Mb/s ngociation automatique Half / Full duplex capability Sortie audio 5.1 voies Prise en charge de l'audio haute dfinition x1 x1 x1 Chaque connector prend en charge 2 lecteurs de disquettes Chaque connecteur prend en charge 2 priphriques IDE Chaque connecteur prend en charge 1 priphrique SATA

Fentes DDR2 DIMM x 2 Mmoire principale Capacit mmoire maximale de 4 Go Chaque DIMM prend en charge des DDR2 de 256Mo/512Mo/1Go/2Go Graphiques Integr dans la chipset GeForce 6150SE

IDE

Contrleur IDE intgr

SATA

Contrleur Serial ATA intgr

LAN Prise en charge audio HD Fentes Connecteur embarqu

Realtek RTL 8201CL PHY

ALC662

Fente PCI Express x16 Fente PCI Connecteur de disquette

Connecteur IDE

x1

Connecteur SATA

x2

28

MCP6PB M2+
SPEC Connecteur du panneau avant x1 Prend en charge les quipements du panneau avant Prend en charge la fonction audio du panneau avant Alimentation lectrique du ventilateur UC (avec fonction de ventilateur intelligent) Alimentation lectrique du ventilateur systme

Connecteur Audio du panneau avant x1 Embase de ventilateur UC Embase de ventilateur systme Embase d'effacement CMOS Connecteur USB Connecteur d'alimentation (24 broches) Connecteur d'alimentation (4 broches) Connecteur de Port d'imprimante Connecteur de Port srie Clavier PS/2 E/S du panneau arrire Souris PS/2 Port VGA Port LAN Port USB Fiche audio Dimension s de la carte Fonctionnal its spciales Support SE Windows XP / Vista / 7 Prise en charge RAID 0 / 1 170 mm (l) X 235 mm (H) x1 x1 x1 x1 x1 x1 x4 x3 x1 x1 x1 x1 x2 x1

Chaque connecteur prend en charge 2 ports USB de panneau avant

Chaque connector prend en charge 1 Port d'imprimante

Biostar se rserve le droit d'ajouter ou de supprimer le support de SE avec ou sans pravis.

29

Motherboard Manual

ITALIAN
SPECIFICA Socket AM2 / AM2+ CPU Processori AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / PhenomX3 / X4 (Watt massimo: 95W) FSB Chipset Supporto di HyperTransport 2.0 Ghz fino a 4 GT/s di larghezza di banda GeForce 6150SE ITE 8718F Super I/O Fornisce le funzionalit legacy Super I/O usate pi comunemente. Alloggi DIMM DDR2 x 2 Memoria principale Capacit massima della memoria 4GB Ciascun DIMM supporta DDR2 256MB/512MB/1GB/2GB Grafica Interfaccia LPC (Low Pin Count) Funzioni di controllo dellambiente: Monitoraggio hardware Funzione "Smart Guardian" di ITE Modulo di memoria DDR2 a canale doppio Supporto di DDR2 533 / 667 / 800 Supporto di DDR2 1066 (by AM2+ CPU) DIMM registrati e DIMM ECC non sono supportati Larchitettura AMD 64 abilita la co mputazione 32 e 64 bit Supporto di Hyper Transport e PowerNow

Integrata nel Chipset GeForce 6150SE La memoria video condivisa massima di 256 MB Modalit Bus Master Ultra DMA 33 / 66 / 100 /

IDE

Controller IDE integrato

133 Supporto modalit PIO Mode 0-4

SATA

Controller Serial ATA integrato

Velocit di trasferimento dei dati fino a 3 Gb/s. Compatibile specifiche SATA Versione 2.0. Negoziazione automatica 10 / 100 Mb/s Capacit Half / Full Duplex Uscita audio 5.1 canali Supporto audio High-Definit ion (HD) x1 x1 x1 x1 x2 x1 Ciascun connettore supporta 2 unit Floppy Ciascun connettore supporta 2 unit IDE Ciascun connettore supporta 1 unit SATA Supporta i servizi del pannello frontale

LAN Supporto audio HD Alloggi

Realtek RTL 8201CL PHY

ALC662 Alloggio PCI Express x16 Alloggio PCI

Connettori Connettore floppy su scheda Connettore IDE Connettore SATA Connettore pannello frontale

30

MCP6PB M2+
SPECIFICA Connettore audio frontale Collettore ventolina CPU Collettore ventolina sistema Collettore cancellaz ione CMOS Connettore USB Connettore alimentazione (24 pin) Connettore alimentazione (4 pin) Connettore Porta stampante Connettore Porta seriale Tastiera PS/2 I/O pannello posteriore Mouse PS/2 Porta VGA Porta LAN Porta USB Connettore audio Dimension i scheda Caratterist iche speciali Sistemi operativi supportati Windows XP / Vista / 7 Biostar si riserva il diritto di aggiungere o rimuovere il supporto di qualsiasi sistema operativo senza preavviso. Supporto RAID 0 / 1 x1 x1 x1 x1 x1 x1 x4 x3 Ciascun connettore supporta 1 Porta stampante x1 x1 x1 x1 x1 x2 x1 Ciascun connettore supporta 2 porte USB pannello frontale Supporta la funzione audio pannello frontale Alimentazione ventolina CPU (con funzione Smart Fan) Alimentazione ventolina di sistema

170 mm (larghezza) x 235 mm (altezza)

31

Motherboard Manual

SPANISH
Especificacin Conector AM2 / AM2+ Procesadores AMD Athlon 64 / Athlon 64 La arquitectura AMD 64 permite el procesado de 32 y CPU FX / Athlon 64 X2 / Sempron / PhenomX3 64 bits / X4 (Vatio mximo: 95W) FSB Conjunto de chips Admite HyperTransport 2.0 Ghz con un ancho de banda de hasta 4 GT/s GeForce 6150SE Interfaz de cuenta Low Pin Iniciativas de control de entorno, Monitor hardware Funcin "Guardia inteligente" de ITE Mdulo de memoria DDR2 de canal Doble Admite DDR2 de 533 / 667 / 800 Admite DDR2 de 1066 (by AM2+ CPU) No admite DIMM registrados o DIMM compatibles con ECC Memoria mxima de vdeo compartida de 256 MB Modo bus maestro Ultra DMA 33 / 66 / 100 / 133 Soporte los Modos PIO 0~4, Tasas de transferencia de hasta 3 Gb/s. Compatible con la versin SATA 2.0. Negociacin de 10 / 100 Mb/s Funciones Half / Full dplex Salida de sonido de 5.1 canales Soporte de sonido Alta Definicin X1 X1 X1 X1 Cada conector soporta 2 unidades de disco flexible Cada conector soporta 2 dispositivos IDE Soporta las tecnologas Hyper Transport y PowerNow

ITE 8718F Sper E/S Le ofrece las funcionalidades heredadas de uso ms comn Sper E/S.

Ranuras DIMM DDR2 x 2 Memoria principal Capacidad mxima de memoria de 4GB Cada DIMM admite DDR de 256MB/ 512MB/1GB/2GB Integrados en el conjunto de chips GeForce 6150SE Controlador IDE integrado

Grficos

IDE

SATA

Controlador ATA Serie Integrado

Red Local Soporte de sonido HD Ranuras

Realtek RTL 8201CL PHY

ALC662 Ranura PCI Express x16 Ranura PCI

Conectores Conector disco flexible en placa Conector IDE

32

MCP6PB M2+
Especificacin Conector SATA Conector de panel frontal Conector de sonido frontal Cabecera de ventilador de CPU X2 X1 X1 X1 Cada conector soporta 1 dispositivos SATA Soporta instalaciones en el panel frontal Soporta funciones de sonido en el panel frontal Fuente de alimentacin de ventilador de CPU (con funcin Smart Fan) Cabecera de ventilador de sistema X1 Cabecera de borrado de CMOS Conector USB Conector de alimentacin (24 patillas) Conector de alimentacin (4 patillas) Conector Puerto de impresora Conector Puerto serie Teclado PS/2 Panel trasero de E/S Ratn PS/2 Puerto VGA Puerto de red local Puerto USB Conector de sonido Tamao de la placa Funciones especiales Soporte de sistema operativo Windows XP / Vista / 7 170 mm. (A) X 235 Mm. (H) X1 X1 X1 X1 X1 X1 X4 X3 Cada conector soporta 1 Puerto de impresora X1 X1 X2 X1 Cada conector soporta 2 puertos USB frontales Fuente de alimentacin de ventilador de sistema

Admite RAID 0 / 1

Biostar se reserva el derecho de aadir o retirar el soporte de cualquier SO con o sin aviso previo.

33

Motherboard Manual

PORTUGUESE
ESPECIFICAES Socket AM2 / AM2+ Processadores AMD Athlon 64 / Athlon 64 A arquitectura AMD 64 permite uma computao de CPU FX / Althlon 64 X2 / Sempron / PhenomX3 32 e 64 bits / X4 (Watt mximo: 95W) Suporta a tecnologia HyperTransport 2.0 FSB Ghz com uma largura de banda at 4 GT/s Chipset Especifica o Super I/O GeForce 6150SE ITE 8718F Proporciona as funcionalidades mais utilizadas em termos da especificao Super I/O. Ranhuras DIMM DDR2 x 2 Memria principal Capacidade mxima de memria: 4 GB Cada mdulo DIMM suporta uma memria DDR2 de 256MB/512MB/ 1GB/2GB Placa grfica IDE Integrada no chipset GeForce 6150SE Interface LPC (Low Pin Count). Iniciativas para controlo do ambiente Monitorizao do hardware Funo "Smart Guardian" da ITE Mdulo de memria DDR2 de canal duplo Suporta mdulos DDR2 533 / 667 / 800 Suporta mdulos DDR2 1066 (by AM2+ CPU) Os mdulos DIMM registados e os DIMM ECC no so suportados Memria de vdeo mxima partilhada: 256 MB Modo Bus master Ultra DMA 33 / 66 / 100 / 133 Suporta o modo PIO 0~4, Velocidades de transmisso de dados at 3 Gb/s. Compatibilidade com a especificao SATA verso 2.0. Auto negociao de 10 / 100 Mb/s Capacidade semi/full-duplex Suporta as tecnologias Hyper Transport e PowerNow

Controlador IDE integrado

SATA

Controlador Serial ATA integrado

LAN Suporte para udio de alta definio Ranhuras

Realtek RTL 8201CL PHY

ALC662

Sada de udio de 5.1 canais Suporta a especificao High-Definition Audio

Ranhura PCI Express x16 Ranhura PCI

x1 x1 x1 x1 Cada conector suporta 2 unidades de disquetes Cada conector suporta 2 dispositivos IDE

Conectores Conector da unidade de disquetes na placa Conector IDE

34

MCP6PB M2+
ESPECIFICAES Conector SATA Conector do painel frontal Conector de udio frontal Conector da ventoinha da CPU x2 x1 x1 x1 Cada conector suporta 1 dispositivo SATA Para suporte de vrias funes no painel frontal Suporta a funo de udio no painel frontal Alimentao da ventoinha da CPU (com a funo Smart Fan) Alimentao da ventoinha do sistema

Conector da ventoinha do sistema x1 Conector para limpeza do CMOS Conector USB Conector de alimentao (24 pinos) Conector de alimentao (4 pinos) Conector da para impressora Conector da Porta srie Teclado PS/2 Entradas/S Rato PS/2 adas no painel traseiro Porta VGA Porta LAN Porta USB Tomada de udio Tamanho da placa Caractersti cas especiais Sistemas operativos suportados Windows XP / Vista / 7 Suporta as funes RAID 0 / 1 170 mm (L) X 235 mm (A) x1 x1 x1 x1 x1 x1 x4 x3 x1 x1 x2 x1

Cada conector suporta 2 portas USB no painel frontal

Cada conector suporta 1 Porta para impressora

A Biostar reserva-se o direito de adicionar ou remover suporte para qualquer sistema operativo com ou sem aviso prvio.

35

Motherboard Manual

POLISH
SPEC Socket AM2 / AM2+ Procesor AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / PhenomX3 / X4 Procesory (Maksymalny Watt: 95W) FSB Chipset Obsuga HyperTransport 2.0 Ghz o szerokoci pasma do 4 GT/s GeForce 6150SE Gniazda DDR2 DIMM x 2 Pami gwna Maks. wielko pamici 4GB Kade gniazdo DIMM obs uguje moduy 256MB/512MB/1GB/2GB DDR2 ITE 8718F Super I/O Zapewnia najbardziej powszechne funkcje Super I/O. Zintegrowana w chipsecie GeForce 6150SE Zintegrowany kontroler IDE Modu pamici DDR2 z trybem podwjnego kanau Obsuga DDR2 533 / 667 / 800 Obsuga DDR2 1066 (by AM2+ CPU) Brak obsugi Registered DIMM oraz ECC DIMM Interfejs Low Pin Count Funkcje kontroli warunkw pracy, Monitor H/W Funkcja ITE "Smart Guardian" Maks. wielko wspdzielonej pamici video wynosi 256 MB Ultra DMA 33 / 66 / 100 / 133 Tryb Bus Master obsuga PIO tryb 0~4, Transfer danych do 3 Gb/s. Zgodno ze specyfikacj SATA w wersji 2.0. 10 / 100 Mb/s z automatyczn negocjacj szybkoci Dziaanie w trybie poowicznego / penego dupleksu 5.1 kanaowe wyjcie audio Obsuga High-Definition Audio x1 x1 x1 x1 x2 x1 x1 Kade zcze obs uguje 2 napdy dyskietek Kade zcze obs uguje 2 urzdzenia IDE Kade zcze obs uguje 1 urzdzenie SATA Obsuga elementw panela przedniego Obsuga funkcji audio na panelu przednim Architektura AMD 64 umoliwia przetwarzanie 32 i 64 bitowe Obsuga Hyper Transport oraz PowerNow

Grafika

IDE

SATA

Zintegrowany kontroler Serial ATA

LAN Obsuga audio HD Gniazda Zcza wbudowan e

Realtek RTL 8201CL PHY

ALC662 Gniazdo PCI Express x16 Gniazdo PCI Zcze napdu dyskietek Zcze IDE Zcze SATA Zcze panela przedniego Przednie zcze audio

36

MCP6PB M2+
SPEC Zcze gwkowe wentylatora procesora x1 Zcze gwkowe wentylatora systemowego x1 Zcze gwkowe kasowania CMOS x1 Zcze USB Zcze zasilania (24 pinowe) Zcze zasilania (4 pinowe) Zcze Port drukarki Zcze Port szeregowy Klawiatura PS/2 Mysz PS/2 Back Panel Port VGA I/O Port LAN Port USB Gniazdo audio Wymiary pyty Funkcje specjalne Obsluga systemu operacyjne go Windows XP / Vista / 7 Obsuga RAID 0 / 1 170 mm (S) X 235 mm (W) x2 x1 x1 x1 x1 x1 x1 x1 x1 x4 x3 Kade zcze obs uguje 1 Port drukarki Kade zcze obs uguje 2 porty USB na panelu przednim Zasilanie wentylatora systemowego Zasilanie wentylatora procesora (z funkcj Smart Fan)

Biostar zastrzega sobie prawo dodawania lub odwoywania obsugi dowolnego systemu operacyjnego bez powiadomienia.

37

Motherboard Manual

RUSSIAN
CPU ( ) FSB AM2 / AM2+ AMD Athlon 64 / Athlon 64 AMD 64 Hyper Transport PowerNow FX / Althlon 64 X2 / Sempron / PhenomX3 32 64 ( : 95W) HyperTransport 2.0 Ghz 4 GT/s GeForce 6150SE DDR2 DDR2 533 / 667 / 800 DDR2 1066 (by AM2+ CPU) DIMM and ECC DIMM , ITE "Smart Guardian" ( )

/ X4

DDR2 DIMM x 2 4 DIMM 256 /512/1/2 DDR2

ITE 8718F Super I/O Super I/O.

GeForce 6150SE 256 "" Ultra DMA 33 / 66 / 100 / 133

IDE

PIO 0~4, ATA Realtek RTL 8201CL PHY 3 /. SATA 2.0. 10 / 100 / /

SATA

ALC662

High-Definition 5.1

PCI Express x16 PCI

x1 x1 x1 2 2 1 SATA

IDE SATA

x1 x2

38

MCP6PB M2+
CMOS USB- (24 ) (4 ) PS/2 PS/2 VGA LAN OS Biostar Windows XP / Vista / 7 OS . RAID 0 / 1 170 () X 235 () x3 x1 x1 x1 x1 x1 x1 x4 x1 x2 x1 x1 1 2 USB- x1 x1 x1 x1 ( )

- USB-

39

Motherboard Manual

ARABIC

AM2 / AM2+ 32 64AMD 64 PowerNow Hyper Transport 3 AMD Athlon 64 / Athlon 64 FX / Sempron / PhenomX3 / X4 / Althlon 64 X2 ): 95 ( 4 GT/s HyperTransport Ghz2.0 GeForce 6150SE Low Pin Count Interface : ITE ""Smart Guardian DDR2 800 / 667 / 533 DDR2 1066 DDR2 )(DDR2 1066 is by AM2+ CPU ECC DIMM 256 Ultra DMA 33 / 66 / 100 / 133 PIO Mode 0~4 /3. 2.0. SATA 100/10 / / 5.1 ITE 8718F Super I/O . Super I/O

DDR2 DIMM
4

256/512 DDR2 DIMM /1 2 GeForce 6150SE IDE

IDE

Serial ATA

SATA

Realtek RTL 8201CL PHY

ALC662

1 1
IDE SATA

PCI Express x16 PCI IDE SATA

1 1 2 1

40

MCP6PB M2+

Smart Fan

1 1 1 1

CMOS USB )24( )4( PS/2 PS/2 VGA USB 170 )( 235 X )(
RAID 0 / 1 /

USB

2 1 1 1 1 1 1 1 1 4 3

Biostar .

Windows XP / Vista / 7

41

Motherboard Manual

JAPANESE

Socket AM2 / AM2+ CPU AMD 64 3264

AMD Athlon 64 / Athlon 64 FX / Althlon 64 X2 / Sempron / PhenomX3 / X4 (: 95W)

FSB

4 GT/s 2.0 GHz GeForce 6150SE DDR2 DIMM x 2 DDR2 DDR2 533 / 667 / 800 DDR2 1066 (by AM2+ CPU) DIMMECC DIMM H/W ITE 256 B Ultra DMA 33 / 66 / 100 / 133 PIO Mode 0~4 3Gb/ SATA2.0 10 / 100 Mb/ / 5.1

4GB DIMM 256MB/512MB/1GB/2GB DDR2 ITE 8718F

Super I/O

Super I/O

IDE

GeForce 6150SE

IDE

SATA

ATA

LAN HD

Realtek RTL 8201CL PHY

ALC662

PCI Express x16 PCI IDE SATA

x1 x1 x1 x1 x2 2 2IDE 1SATA

42

MCP6PB M2+

CPU CMOS USB (24) (4) PS/2 PS/2 I/O VGA LAN USB RAID 0 / 1 BiostarOS 170 mm () X 235 mm () x1 x1 x1 x1 x1 x2 x1 x1 x1 x1 x1 x1 x1 x1 x4 x3 1 2USB CPU()

OS Windows XP / Vista / 7

2009/09/18

43

You might also like