You are on page 1of 6

Quicknote

Upgrading the SST-PB3-CLX Profibus scanner firmwares


Rev Date 1.1 21/05/2010 File Name Upgrading the SST-PB3-CLX Profibus scanner firmwares

Description
Product concerned: SST-PB3-CLX-RLL (SAP Number 1120160018) Product version: all Environment: SST Configuration Tool V3.11.4.0 or upper Related documents: SST-PB3-CLX-RLL User Manual V1.2 or upper Restriction: None

Summary: This document will explain you why there are 2 firmwares versions for the new BradCommunications SST Profibus module, how to check them and how to upgrade them if needed. We strongly recommend reading this document from start to the end in order to get enough information before upgrading.

1- Why there are 2 firmwares ?


The SST-PB3-CLX is a new architecture. It has been developed with better technology using 2 processors. This is why there are 2 firmwares: The pfbclx.ss3 file which manages the Profibus communication The pfbclx.ss4 file which manages the communication between the backplane and the module.

2- How to check the firmwares versions ?


=> The pfbclx.ss4 To know the Backplane firmware you need to look at the display of the module during the Boot phase, it will show the Firmware version (ex.: 7.33). => The pfbclx.ss3 To know the Profibus Firmware you can use the SST Configuration Tool or the HyperTerminal tool (which is also the upgrading utility). From the SST Configuration Tool: Click on Connect button then on Firmware version

Profibus Firmware Version

Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 2 of 6

From the HyperTerminal connection:

Serial Null Modem Cable

Create a connection with HyperTerminal as follows :

Cycle power on the CLX rack. (If you can't, INHIBIT the SST module from RSLogix and put it OFFLINE from SST configuration tool, then take it out and insert it again in the rack). While the SYS LED is red after powering up, hit several times the exclamation mark (!) from your keyboard until getting the following result:

To get the Profibus Firmware version, enter the command ver pfbclx.ss3 as shown in the next picture (Help command shows all the available options)

Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 3 of 6

0711

3- How to upgrade the firmwares versions with HyperTerminal ?


=> The pfbclx.ss3 Start a HyperTerminal connection as indicated above (Part 2 From the HyperTerminal connection)

To upgrade the firmware, use the command Ry pfbclx.ss3 to initiate a Ymodem send.

Once the series of C starts

send the file using the Ymodem send.

Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 4 of 6

Ymodem send

Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 5 of 6

Check it out with the command ver pfbclx.ss3.Then enters the command run pfbclx.ss3 to exit System Configuration mode and start up.

=> The pfbclx.ss4 Start a HyperTerminal connection as indicated above (Part 2 From the HyperTerminal connection)

To upgrade the firmware, use the command Burn. Once the series of C starts, send the file using the Ymodem send as indicated above (Part 3 Ymodem send), but this time you have to choose the file pfbclx.ss4

Cycle power on the CLX rack

Please wait for the message then cycle power on the CLX rack. (If you can't, take the SST module out and insert it again in the rack)

Upgrading the SST-PB3-CLX Profibus scanner firmwares V1.1 Page 6 of 6

You might also like