You are on page 1of 1

HMF Flange

Riser Joint
New Composite Material Marine Riser
KT Riser Tensioner Ring
SDL Tensioner Support Ring
with Optional Fluid Bearing
MR Riser Coupling

Capital Drilling Equipment
Termination
Joint
Mudmat
Guide Base
BOP Stack
Annular Preventer
Intermediate Flex Joint
True metal-to-metal sealing
Patented passive casing hanger load support design
with a load carrying capacity of more than 7 million lb.
High capacity, fatigue resistant Conductor housing to
High Pressure housing interface
Seal fully energized by running tool
Generous flow-by area with large particle size
clearance
Complies with industry standards, API 17D, NACE MR-
01-75; design certified by Lloyds
VX/VT dual metal-to-metal gasket prep
MS-700 Subsea Wellheads
Diverter
Insert
Diverter
Housing
Telescopic Joint
SingleFlex Joint
with Riser Adapter
SHD-H4 Connector
E x F HAR
(High Angle Release)
H4 Connector
SMS-700 Subsea Wellhead
18-3/4 - 15,000 psi
Technology at Work vetco
TM
Vetco Gray
TM
H-4 Family of Subsea Wellhead
Connectors for wellhead, BOP and
LMRP applications
355 of contact area in lock profile
Dual hydraulic operating system
Self-aligning connector to wellhead
interface
Reliable metal-to-metal VX/VT sealing
Hydrate protection system
H-4 Connectors
Ideal for deep water applications where high load
operating conditions exist
Stepped diameter design of pin and box simplifies
engagement, even with severe vessel movement
No loose parts, preventing bolt loss and potential
thread damage
Field removable and replaceable nose piece
Locking bolts preloaded in excess of rated coupling
loads to extend fatigue load of riser system
HMF Riser Coupling
MR-6 Riser Coupling
Easy stabbing, fast makeup, and positive alignment
Suitable for operating in water depths up to 7,500 ft
depending on environmental and well control
conditions; MR-10 designs can operate in depths to
10,000 ft.
Preloaded connection significantly reduces the range
of alternating stresses induced by cyclic loading and
improves fatigue life
Primary load path for tensile and bending loads is
through the dogs and into the body and does not
impact actuating screws
Telescopic Joint is run and pulled through the rotary
table without disconnecting the tensioning lines from
riser tensioning ring
Riser tensioning lines remain properly spaced out at
all times
Hydraulic piping for lockdown/storage dogs remains
permanently connected
Hydraulically disconnects from telescopic joint and
locks to a mating profile on the bottom of the diverter
housing for convienent, out-of-the-way storage
SDL Tension Ring
KT Tension Ring
Forms a termination point between the riser tensioner
and the marine riser system
Simplifies running and retrieving marine riser by
eliminating makeup/breakout of tensioner lines and
hydraulic hoses in the moon pool area
Choke, kill, and auxiliary line terminations permanently
connected
Orientation pins on the ring engage slots in telescopic
joint line termination housing for easy makeup
Permanently installed tensioner lines maintain proper
orientation with rig drilling tensioners
Gimbal
Gimbal shock absorber supports up to
2,000,000 lb and gimbals when the riser is
positioned in the spider
Reduces impact loads when running and
landing marine riser joints
Available for MR-6E, MR-6H SE, and HMF riser
systems
Maximum rated riser tensile load capacity in
locked position
Hydraulic latch release for inner and outer
barrels available
Dual split/solid packer elements
Fixed or rotating integral tensioner rings
Prepped for non-integral SDL, SDC and KT
tensioning rings
Fluid or roller bearing prep
Single Flex Joint
Installed in the LMRP below the riser/BOP
Stack Interface
Uses a combination elastomeric bearing
and seal unit to eliminate the need for a
pressure balanced ball and socket
interface with seals
Up to 2 million lb tensile load capacity
Rated for H2S service and oil-based
drilling mud
Angular deflection to 10 degrees on
either side of its axial center while
subjected to tensile loading and internal
pressures up to 3,000 psi
Pressure balance and lubrication
systems not required
Installed below the telescopic joint
Up to 2.5 million lb tensile load capacity
Angular deflection to 20 degrees on either side of its
axial center while subjected to tensile loading and
internal pressure of 1,500 psi
The marine riser handling spider supports the
marine riser string while the next joint is
removed or installed. A positive locking device
prevents accidental release.
MR-6E Hydraulic Spider
MR-6H SE Spider
The MR-6H SE riser handling spider supports the
riser string on hydraulic sliding dogs. Six
hydraulic units move the cam ring up and down
to make or break the connector.
HMF Riser Spider
The HMF hydraulic-gate riser handling spider is
used when running or retrieving HMF riser joints
through the rotary table. Split gates, operated by
hydraulic cylinders, support the riser string
when the gates are in the closed and locked
position.
KFDJ Diverter
Fixed support housing, allows installation of outlets up
to 20" diameter
Diverter, spacer spool and overshot packer assembly
may be pulled or run without connecting or
disconnecting the flowline, fill-up line and vent lines.
The overshot packer on the bottom of the diverter spacer
spool assembly reduces the nipple-up time normally
required to weld flanges or hubs to casing.
Available with a rotating insert which provides low
pressure packoff on the kelly or drill pipe during drilling.
KFDJ Diverter
MR-6E Hydraulic Spider
MR-6H SE Spider
Gimbal
Telescopic Joint
CSO Diverter
Used on the majority of floating rigs
Complete open-hole shutoff with 20 through-bore
Rated 1,000 psi for closure on 5 drill pipe; 500 psi for
closure on open hole
10 second closing time on pipe or open hole
Housing accommodates large diameter riser buoyancy
modules
High capacity systems available for supporting the Riser
String from Diverter Housing in emergency hangoff
situations
KFDS-CSO Diverter
Intermediate
Flex Joint
HMF Riser Coupling
MR-6H SE
Riser Coupling
MR-6H SE Riser Coupling
Automated make-up with minimal personnel
intervention
Utilizes reliable, field proven concepts and profiles (H-
4 & MR)
High preload / efficient load path
Parts subject to wear are easily replaceable
Easy maintenance, service and inspection with all
critical areas readily accessible
External surfaces of pin and box
can be fully TSA protected
Handling spider modularized to allow quick change
out of critical parts or subassemblies, if required.

You might also like