You are on page 1of 70

Page 1 of 70

Name :
Reg No :
Branch :
Year & Semester :




w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 2 of 70

PLUMBING
Introduction
Plumbing deals with the laying of a pipeline. A craftsman may be perfectly proficient
with the hammer, saw and other tools, but the faces difficulties with leaking pipes and
overflowing toilets. Many people rush to a plumber on seeking a tripping pipe, but a person with
a little knowledge of the sanitary system can control this problem easily, saving time and, one
with help of few tools.
Plumbing tools
The tools used by a plumber can be classified as follows
1. Pipe wrench 4. Pipe vice 6. Pipe cutter
2. Hacksaw 5. Dies 7.Files and Rasps
3. Plumb bob
Pipe wrench
A pipe wrench is used for holding and turning the pipes, rods and machine parts.
Wrenches are classified as follows.1.Fixed wrenches 2. Adjustable wrenches.

Pipe vice
A pipe vice is fitted on the work bench. This has a set of jaws to grip the pipe and prevent
it from turning while cutting, threading and fitting of bends, couplings etc. The yoke vice is
commonly used in plumbing used in plumbing practice.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 3 of 70


Pipe cutter
The pipe cutter mainly consists of three wheels which are hardened with sharp cutting edges
along their periphery. Of these three wheels, one can be adjusted to any desired distance to
accommodate different size of pipes. After adjusting the cutter on a pipe, it is around the pipe, so
that the cutter wheels cut the pipe along a circle as shown in fig.


Hack saw
A hacksaw is used for cutting metal rods, bars, pipes, etc.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 4 of 70


Threading dies and taps
It is used for cutting external thread on pipes. Threads are produced in various shape and
sizes which are used for fitting inside a handle.

Files and rasps
The file surface is covered with sharp edged teeth and its used for removing metal by
rubbing. A rasp is used for finishing the surface of the work piece.
Plumb bob
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 5 of 70


It is used for check the vertical line and made up of steel or brass.
Pipe fittings

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 6 of 70

Pipe fittings are made up of wrought iron. The size of pipe fitting is designated by the size of the
pipe on which it fits. some of the common pipe fittings are shown in fig.
Coupling
It is a short a cylindrical sleeve with internal threads throughout. A couplings is used for joining
two pipes in a straight and bend where at least one pipe can be turned.
Union
A union is used for joining two pieces of pipes, where either can be turned. It consists of
three parts, two parts joint can be screwed, in to two pipe ends, and the third on for tightening
called centre part.
Nipple
A nipple is a short piece of pipe with external threads at both ends. It is used to make up
the required length of a pipe line.
Elbow
An elbow is to make an angle between adjacent pipes.
Tee
A tee is a fitting that has one side outlet at a right angle to the run. It is used for a single
outlet branch pipe.
Reducer
It is used to connect two different sized of pipes
Plug
It is used to screw on to a threaded opening, for closing it temporarily.


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 7 of 70

Valves
Valves are used for regulating the flow of fluid through a pipe. The commonly used
valves in plumbings are
1. Gate valve 2.Globe valve
3. Plug valve 4.Check valve 5. Air relief valve.

Types of pipe joints
Bell and spigot joints

A connection between two sections of pipe i.e. the straight spigot end of one
section is inserted into the flared out end of the adjoining section. The joint is sealed by a sealing
component.

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 8 of 70

Flanged joints

A flanged joint helps to connect and disconnect two pipes as per the need. A similar
example is as shown in fig.
Bolted joints

The use of bolted joint is advantageous in the following circumstances
1. The component that cannot be serviced in line.
2. The components being joined that are not capable of being welded.
3. Quick field assembly is required.
4. The component or pipe section that needs to be frequently removed for surface.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 9 of 70

Threaded joints

Threads are cutted in a pipe, flange coupling to connect them with each other and these
joints are called threaded joints.
Flexible joints

The flexible joints are generally used to connect between a washbasin and an angle valve.
Swing joints
Swing joints are special purpose joints mainly used for industrial oriented purposes where
a long bend is required.


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 10 of 70

Welded and brazed joints


Welded and brazed joints are the most commonly used joints for joining pipe
components.
Expansion joints

Expansions joints are specially designed in pipeline where a small extension of pipe is
required



w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 11 of 70

Single line diagram

Single line diagram are most commonly used in plumbing diagram. All power plants and
bottling plant pipes are made by the single line piping diagram.
Double line diagram

It is used for catalogs and other applications where the visual appearance is more
important.




w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 12 of 70






















w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 13 of 70

Ex.no: Plumping of one tap water distribution system Date:
Aim
To construct the one tape water distribution system by using plumbing components.
Fittings required
1. PVC pipes
2. Tank fitting(GI)
3. Union(GI)
4. MTA(PVC)
5. Gate valve
6. Elbow
7. Reducer(GI)
8. Bend(PVC)
9. FTA(PVC)
10. TAP(PVC)
Procedure
1. The given PVC pipes are measured out to the required size.
2. The suitable die is selected.
3. Gate valve is connected between the two MTA.
4. 1 x reducer connected between 1 pipe and pipe.
5. 1 (GI) bend is connected between the two pipes.
6. x1/2 reducer connected between pipe and .
7. bend connected between and pipe.
8. At the end of the pipe MTA tap is connected.
Result
Thus the plumbing of one tap water distribution system was constructed.






w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 14 of 70


























w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 15 of 70


Ex.no: Plumping of Four tap water distribution system Date:
Aim
To construct the one tape water distribution system by using plumbing components.
Fittings required
1. PVC pipes
2. Tank fitting(GI)
3. Union(GI)
4. MTA(PVC)
5. Gate valve
6. Elbow
7. Reducer(GI)
8. Bend(PVC)
9. FTA(PVC)
10. TAP(PVC)
Procedure
1. The given PVC pipes are measured out to the required size.
2. The suitable die is selected.
3. Gate valve is connected between the two MTA.
4. 1 x reducer connected between 1 pipe and pipe.
5. 1 (GI) bend is connected between the two pipes.
6. x1/2 reducer connected between pipe and .
7. bend connected between and pipe.
8. Finally FTA connected at four ends and then tap fixed to the four ends.
Result
Thus the plumbing of Four tap water distribution system was constructed.





w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 16 of 70

CARPENTRY
Introduction
Carpentry may be designed as the process of making wooden articles and components
such as roots, floors, partitions, doors and windows. Carpentry involves cutting, shaping and
fastening wood and other materials together to produce a finished product. Preparation of joints
is one of the important operations in wood work.
J oinery denotes connecting the wooden parts using different points such as lap joints,
mortise and teman joints, bridle joints, etc.
Carpentry Tools
Carpentry tools are used to produce components to an exact size.
The types of carpentry tools are as follows.
1. Marking tools 2.Measuring tools 3. Holding tools
4. Cutting tools 5.Planning tools 6.Boring tools
7. Striking tools 8.Miscellaneous tools

Marking tools
It is used to marking lines parallel to the edges of a wooden piece. It consists of a square
wooden stem with a sliding wooden stock on it. On the stem, a marking pin is attached which is
made up of steel. This stem is provided with a steel nail to scratch the surface of the work. It
consists of two pins; the distance between the pins is adjustable. It is used to draw parallel lines
on the stock.
Measuring tools
The carpentry measuring tools are classified as follows
1. Steel tape 2.Steel rule 3.Calipers
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 17 of 70

Steel tapes and steel rules are mainly used for measuring short and lengths in millimeters.
A try square is used for testing squareness and marking of joints.
A mitre square is used for marking and measuring an angle of 45 degree.
A bevel square is used for marking and listing angles between 0 degree to 180 degree.



Calipers are used for the precision measurement of cylindrical surface. Inside calipers are
used for measuring outside diameter and outside calipers are used to measure inner diameter of a
pipe
Holding tools
The carpentry holding tools are shown in fig.

Carpentry vice
A carpentry vice is the common work holding device. It consists of one fixed jaw and one
movable jaw. Its one jaw is fixed to the side of the table while the other is movable by means of
a screw and a handle.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 18 of 70

Bar clamp
The bar clamp (or) sash cramps are generally used in pairs in glueing up operations at the
final assembly of joinery work. It is made up of a steel bar of T-section, wine malleable iron
fittings and a steel screw.
G-cramp
G-cramp is made up of malleable iron with acme threads of high quality steel .It can be
used for clamping small work when glueing up.
Cutting Tools


Saws
A saw is used to cut wood into pieces. There is different type of saws, designed to suit
different purpose. A saw is specified by the length of its tooled edge. The following saws are
used in the carpentry section.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 19 of 70

Rip Saw
The blade of rip saw is either straight or skew-backed. The teeth are so set that the cutting
edge of this saw makes a steeper angle about 60
0
Cross Cut saw
This is similar in shape of a rip saw. It is used to cut across the grain of the stock. The
correct angle for cross cutting is 45
0
.The teeth are so set that the saw kerf is wider than the blade
thickness. This allows the blade to move freely in the cut without sticking.
Tenon or back saw
A tenon saw is used for fine and accurate work. It consists of a very fine blade, which is
reinforced with a rigid steel back. The teeth are shaped like those of cross cut saw.



Chisels
Chisels are used for cutting and shaping wood accurately. Wood chisels are made in
various blade widths, ranging from 3 to 50mm .Most of the wood chisels are made into tang
type, having a steel shank which fits inside the handle.
Firmer chisels
These are general purpose chisels and are used either by hand pressure or by a mallet.
The blade of a firmer chisel is flat and their sloping face is at an angle 15
0
to 52
0
.
Mortise Chisels
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 20 of 70

These are general purpose chisels and are used for cutting mortises above 9 mm wide.
The blade of a firmer type in which they have a thicker section and a stronger neck. By means of
this chisel we can apply more Leverage to remove waste wood from the mortise.


Bevel chisels
A bevel chisel is similar in construction to the firmer chisel. Its edges are bevelled to
allow access to difficult corners. It has a blade with a bevelled back due to which it can enter
sharp corners for finishing in dovetail joints.
Planning Tools
In general, planes are used to produce flat surfaces on wood. The cutting blade used in a
place is very similar to a chisel. The blade of a plane is fitted in a wood or metallic block at an
angle.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 21 of 70




J ack plane which is about 35 cm long is used for general planning. A smooth plane that is
about 20 to 25cm long is used for smoothening the stock .Being short; it can follow even the
slight depressions in the stock better than the jack plane. Smooth plane is used after using the
jack plane.
A rebate plane is used for making a rebate .A rebate is a recess along the edge of a piece
of wood which to generally used for positioning glass in frames and doors. A plough plane is
used to cut grooves, which are used to fix handle in a door.
Boring Tools
Boring tools are used to make holes in wood .Common types of boring tools are as follows.

1. bradawl
2. Gimlet
3. Brace
4. Bit and drill
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 22 of 70




A brace bolds and turns the bit and boring of a hole is obtained. A brace having two jaws
is used for holing the bit in one end. It has two types, namely ratchet brace and wheel brace.
A bradawl and a gimlet are used for boring small holes. These tools are hand operated.

Striking Tools

Hammers
The cross peen hammer is mostly used for positioning small nails. The head is tightly
held in the handle with the help of iron wedges. The claw hammer is effective in removing very
large nails and also for driving the nails using the other end of the hammer.
Mallet
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 23 of 70

A mallet is used to drive the chisel, when considerable force is to be applied, which may
be the case in making deep rough cuts. A steel hammer should not be used for this purpose, as it
may damage the chisel.




Rasp file

A rasp file is shown in Fig. rasp is a file used for finishing the surface of wood. The rasp
has sharp cutting teeth on its surface for this purpose. The file is used for removing rasp marks
end finally the scratches left by the fix are removed with the scraper and glass paper.


Oil stone
This is an essential flat used for providing sharp edges on cutting tools. The oil stones
may be artificial or natural stones. The carborundum is the best artificial stones where as the
Arkansas are the natural stones.
Miscellaneous Tools
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 24 of 70


Spirit level
The spirit level is used to check the level of the wooden surface. A narrow glass tube is
fitted into a small rectangular wooden box. The glass tube contains spirit and a bubble. On
placing the spirit level if bubble stays in the middle, then the surface is flat otherwise it is having
a slope.
Pincers
They are made up of steel with a hinged joint and are used for pulling out small nails
from wood.
Screwdrivers
Screwdriver is used for driving wood screws into wood or unscrewing them. The
screwdriver used in carpentry is different form the other common types.
CAPPENTRY MACHINES
Carpentry machines are used for large production of components. The commonly used
carpentry machines are described below.
Wood Turning Lathe
A wood turning lathe is the most important machines used in a carpentry shop. It is used
for producing cylindrical, spherical and tapered shape products.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 25 of 70




A wood working lathe consists of a cost iron body, main motor, cone pulley system,
spindle, tool post, head stock, liveanddead centers and speed control devices. In wood working
lathes, the workpiece is held between the two centers. The tool is held in the tool post.

The workpiece is rotated in between the two centers whereas the cutting tool passes
towards the work and removes the material and produces the desired shape and size.

Circular Saw
A circular saw is used for ripping, cross cutting, leveling, grooving and rebating,. It
consists of a cast iron table, a circular cutting blade, guide ways, saw guide, elevating hand
wheel, tilting handwheel,and a main motor.
In circular saws, the workpiece is held on the table. Then the work is moved against the
circular saw to perform the operations. The saw hand wheel is used to adjust the height of the
saw above the surface of the table.
The table can be tilted up to 45
O
for cutting with different angles. It is an ideal machine
for large production. The size of the saw depends upon the size of the saw blade.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 26 of 70


Band Saw
A band saw is used for cross cutting, leveling, mitering, grooving and rebating. It consists
of two wheels having an equal diameter, saw guider, frame table, wheel guard, saw tension,
arrangement and steel blade having teeth on it. The saw blade travels over the rims of two
wheels. The blade width varies from 6 to 25 mm and the thickness is about 1 to 2 mm.


CARPENTRY PROCESSES
In a carpentry shop, a number of operations are performed to get the finished workpiece.
The different types of process performed in a carpentry shop can be classified as follows.
Marking and Measuring
It is the process of setting of dimensions on wooden pieces to obtain the required shape.
This is the first step for further carpentry operations. The marking operation is done with use of
marking tools. Before marking, one end is planed for reference.



Sawing
Sawing is the process of cutting wood to the required shape and size such as straight,
inclined or curved. Sawing can be done along the grains or across the grains.
In sawing, wooden work is fixed in a vice and wood is moved up to prevent vibrations during
sawing.

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 27 of 70

Planing
Planing is an operation of obtaining, smooth, dimensionally true surface of wood by
using a planer. It is done along the grains.So; smooth surface is achieved. This process can be
also called facing or edging.
Chiseling
It is the process of cutting a small stock of wood to produce required shapes.

Mortising and Tenoning
Mortising is the process of producing a mortise, i.e. a rectangular or square holes and
recesses in wooden pieces. A tenon is a projected piece of wood that fits into the corresponding
mortise. This process is done by using mortise chisels and a mallet.
Boring
Boring is the process of producing through holes or blind holes in wooden piece. This
process can be done straight or inclined according to the type of work. The small holes are
produced by using bradawl and gimlet, whereas large holes are produced by using braces, drills.
Grooving
Grooving is the process of making grooves tonguing is the process of producing
corresponding projections of wood for fitting into grooves. Grooving and tonguing operation can
be seen in drawing boards, floor boards and partitions. Grooving is done with a plough plane
tool, and tonguing is done with a moulding plane tool.

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 28 of 70


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 29 of 70


Ex.No: T-Joint Date
Aim
To make the T-joint the required dimensions from the given workpiece.
Material Required
Soft wood of size 300x50x50 mm.
Tools Required
1. J ackplane
2. Carpentry vice
3. Try square
4. Marking gauge
5. Steel rule
6. Tenon saw
7. Rip saw
8. Firmer chisel
9. Mallet
Procedure
1. The given workpiece is firmly clamped in the carpentry vice and any two adjacent
surfaces are planed to get right angles using the jack plane.
2. Using the try square, the right angles of planned faces are checked.
3. Now the other two surfaces are planned to get smooth surface.
4. The workpiece is cut into two pieces by using the rip saw.
5. Using the steel rule and marking gauge, marking is done for T-joint on the two halves.
6. In one half, the unwanted portions of wood are removed by using the tenon saw and
firmer chisel. The same procedure is done for the other half of workpiece.
7. Using the jack plane, the other two faces of workpiece is planned to the required size.
8. The finished two pieces are assembled to getter to form the T-joint.
9. Finally, the finished job is checked for required size and shape using the steel rule and try
square.
Result
Thus the required T-joint is obtained.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 30 of 70


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 31 of 70



Ex.No: Dovetail Joint Date
Aim
To make the Dovetail joint the required dimensions from the given workpiece.
Material Required
Soft wood of size 300x50x50 mm.
Tools Required
1. J ackplane
2. Carpentry vice
3. Try square
4. Mortise gauge
5. Mallet
6. Firmer chiesel
Procedure
1. The given workpiece is firmly clamped in the carpentry vice and any two adjacent
surfaces are planed to get right angles using the jack plane.
2. Using the try square, the right angles of planned faces are checked.
3. Now the other two surfaces are planned to get smooth surface.
4. The workpiece is cut into two pieces by using the rip saw.
5. Mark the dimensions for the dovetail joint on the two pieces using the steel rule and
marking gauge.
6. Remove the unwanted portions as per the drawing and assemble to check proper
fitting.
Result
Thus the desired dovetail joint is obtained.






w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 32 of 70


WELDING
Introduction
Welding is metal joining process wherein localized coalescence is produced either by
heating the metal to a suitable temperature, with or without the use of filler metal, with or
without application of pressure.
The filler material has similar composition and melting point temperature as that of the
base metal. It is used to fill gap between the joint surfaces.
Types of welding
The welding process is divided into two main sub divisions.
Plastic welding
The pieces of metal to be joined are heated to the plastic state and then forced together
by external pressure without the addition of filler material.
Forge welding
The work piece are placed in a forge or other appropriate furnace and heated within the
area to be joined to the plastic condition. Then parts are quickly superimposed and worked into a
complete union by hand or power hammering or by pressing together.
Resistance welding
In resistance welding, a heavy electric current is passed through the metals to be joined
over limited area, causing them to be locally heated to plastic state and the welding is completed
by the application of pressure for the prescribed period of time.



w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 33 of 70

Fusion welding
In fusion welding, the metal parts to be joined are melted and then allowed to solidify
pressure is not applied and filler metals may be used for this type of welding.
Gas welding
Gas welding is a process in which the required heat to melt the surfaces is supplied by a
high temperature flame obtained by a mixture of two gases.
Usually the mixture of oxygen and acetylene is used for welding purpose.
Electric Arc welding
Electric arc welding is the process of joining two parts by melting their edges by an
electric arc with ort without the application of pressure and with or without use of filler metals.

Thermit welding
Thermit welding is a fusion process in which weld is effected by pouring super heated
liquid thermit steel, around the parts to be united with or without the application of pressure.



Oxy-acetylene welding
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 34 of 70


In oxy-acetylene welding oxygen and acetylene are the two gases used for producing
flame. Oxygen is mainly used for supporting the combustion intensity.
The oxygen and acetylene under high pressure in cylinders which are fitted with pressure
regulator. Each cylinder is connected to the blowpipe by flexible hoses. The oxygen cylinders are
painted block and acetylene cylinders are painted maroon.
When acetylene is mixed with oxygen in correct proportions in the welding torch,
ignition is takes place. The flame resulting at the tip of the torch is sufficient enough to melt and
the parent material .The flame temperature is about 3200C.The filler metal rod is generally
added to the molten metal pool to built up the seam for greater strength.
Types of flames
1 .Neutral Flame (Oxygen, Acetylene in equal proportions)
2. Oxidizing Flame (excess of Oxygen)
3. Reducing Flame (excess of Acetylene)

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 35 of 70


Neutral Flame
A neutral flame is produced when approximately equal volumes of oxygen and acetylene
are mixed in the welding torch and burnt at the torch tip.
The temperature of the neutral flame is of the order of about 3260C
The flame has inner cone which is light blue in color.
The neutral flame is used for welding of mild steel, copper, aluminum, cast iron, etc.
Oxidizing Flame
If the volume of the oxygen supplied to the neutral flame is increased, then resulting
flame will be oxidizing flame.
The temperature of oxidizing flame is of the order of about 3482C.
Normally the outer flame envelope is much shorter. It has very small white inner cone.
This flame is used to weld copper-base metals, zinc-base metals.
Reducing Flame (Carburizing Flame)
If the volume of the oxygen supplied to the neutral flame is reduced, the resulting flame
will be a reducing flame.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 36 of 70

In this case, flame is recognized by acetylene feather which exists between the inner cone
and outer envelope. The outer flame envelope is longer than that of the neutral flame and is
usually much brighter in color.
It has an appropriate temperature of 3038C.
In this type, flames are used to weld the high-carbon steel, non-ferrous alloys, zinc-
bearing alloys.
Flame Adjustment
Neutral flame
To get the neutral flame, add sufficient oxygen to make the white cone clear and round.
During the neutral flame, the gas mixture from the blow pipe consists of oxygen and
acetylene in the ratio of 1:1:1
Oxidizing flame
To get the oxidizing flames add, more oxygen.
The white cone will becomes short and sharp.
The flame will produce a hissing sound and will have a short length.
Carburizing flame
To get the carburizing flame adds more acetylene to the neutral flame.
The white cone will become long surrounded by a feather-like portion. Flame will burn
quietly and have more length.
Filler metal
It is the material that is added to the weld pool to assist in filling the gap. Filler metal
forms an integral part of the weld. The filler metal is usually available in rod form. The rods are
called filler rods.

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 37 of 70

Fluxes
During the welding, if the metal is heated in the air, oxygen in the air combines with the
metal 5to form oxides which result in poor quality, low strength welds or in some cases may
even make welding impossible. In order to avoid this problem, a flux is added during the
welding. The flux prevents oxidation by preventing oxygen from contacting the weld zone.
No flux is used in the gas welding of steel.
The most commonly used flux materials are boric acid, soda ash and sodium chloride.
Arc welding
In the arc welding process, the source of heat is electricity. In arc welding process,
coalescence is produced by heating the work piece with an electric arc struck between electrode
and the work piece. Welding may be carried out in air or in an inert atm. Filler material may or
may not be used. The temperature of the arc is of the order of 3600C.
Principle of arc welding
Principle of operation

The heat required for joining the metals is obtained from an electric arc. The electric
motor generator or transformer sets are used to supply high electric current and the
electrodes are used to produce the necessary arc. The electrode serves as the filler rod and
arc melts the surfaces so that the metals to be joined are fused together.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 38 of 70

he transformer type welding machine produces AC current. It takes power directly
Comparison of A.C and D.C arc welding equipments
No Alternating current(AC) Direct current(DC)
1 It is not suitable for joining non-ferrous
metals.
It is not suitable for both ferrous and
non-ferrous metals.
2 Only coated electrodes can be used. Bare electrodes can also be used.
3 Consumes less power. Consumes more power.
4 High efficiency. Low efficiency.
5 Cost of equipment is less. Cost of equipment is more.
6 Noiseless operation. It gives noise.
7 Not suitable for welding thin sections. Suitable for welding thin sections.
Electrodes
Filler rods are used in arc welding are called as electrodes. The Electrodes are made of
metallic wire called core wire. It is uniformly with a protective coating called flux while fluxing
an electrode about 20 mm of length is left bare at one end for holding it using electrode holder. It
is used to transmit full current from electrode holder to the front end of the electrode coating.


Electrodes for Arc welding
Consumable Electrode Non-consumable electrode
These electrodes are made up of copper,
steel, brass etc.
Electrodes made up of carbon and
graphite varieties are used in DC
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 39 of 70

arc welding.
Tungsten electrodes used for both
AC and DC welding.

Electrode Holder


It is a device used for mechanically holing th electrode and conducting current to
it.
Electrode holder should be light, to minimize fatigue incurred by the welder.
J aws are made to hold the bare end of the electrode in either at vertical or at an
angular position.
Welding Cables
Two cables are needed for welding purpose. One is used to connect the power
source to electrode; another cable is connected to ground.
The cables are well isolated with rubber.
Welding Bead cleaning accessories
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 40 of 70


Chipping hammer
A chipping hammer is chisel-shaped one and it is used to remove the slag from the weld
bead.
Wire Brush
A wire brush made up of stiff steel wire, embedded in wood, removes small particles of
slag from the weld bead after the chipping hammer is used.
Hand Screen
It is a protective device used in arc welding. A hand shield is held in the hand of the
welder and it is fitted with a suitable fitter lens.
Helmet
It is used for shielding and protecting the face and neck of the welder and it is fitted with
a suitable fitter lens.
Tongs
Tongs are used to handle the hot metal-welding job while cleaning; they are also used to
hold the metal for hammering.
Goggles
Chipping goggle is used to protect the eyes while chipping the slag. They are fitted while
a plain glass to see the area to be cleaned.

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 41 of 70


Hand Gloves
Hand gloves are used to protect the hands from electrical shock, arc radiation and hot
spatters.
Advantages of arc welding
Flux shielded manual metal arc welding is the simplest of all the arc welding process.
The equipment can be portable and the cost is fairly low.
This process finds innumerable applications, because of the availability of a wide variety
of electrodes.
A big range of metals and their alloys can be welded.
Disadvantages of arc welding
Because of the limited length of each electrode and brittle flux coating on it,
Mechanization is difficult.
In welding long joints, as one electrode finishes, the weld is to be progressed with the
next electrode. Unless properly cared, a defect may occur at the place where welding is
restarted with the new electrode.
It cannot be used to weld metal thickness less then 1.6 mm.








w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 42 of 70



Ex. No : LAP JOINT Date :


























w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 43 of 70




Aim
To join the given two work pieces as a lap joint by arc welding.
Material used
Mild Steel plates.
Tools required
Welding power supply Flat file
Welding rod Chipping hammer
Electrode holder Wire brush
Gloves and apron Earthing clamps
Shield and goggles
Procedure
1. First of all, the work pieces must be thoroughly cleaned to remove rust, scale and other
foreign materials.
2. Then the given work pieces are placed on the table in such a way that one work piece
is placed on the other work piece like the LAP joint is formed.
3. Appropriate power supply should be given to the electrode and the work pieces.
4. Now the welding current output may be adjusted.
5. When current is passed, arc is produced between the electrode and work pieces.
6. Then the welding is carried out throughout the length.
7. As soon as the welding process is finished, switch off the current supply and allow the
work piece to cool.
8. Slag is removed by chipping process with the help of chipping hammer.
9. Finally using wire brush, welded portions are cleaned.


Result
Thus the given two work pieces are joined as a lap joint by arc welding.



w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 44 of 70


Single V butt joint


























w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 45 of 70


Aim
To join the given two work pieces as a single v butt joint by arc welding.

Material used
Mild Steel plates.
Tools required
Welding power supply Flat file
Welding rod Chipping hammer
Electrode holder Wire brush
Gloves and apron Earthing clamps
Shield and goggles

Procedure
1. First of all, the work pieces must be thoroughly cleaned to remove rust, scale and other
foreign materials.
2. Then the given work pieces are placed on the table in such a way that work pieces are
brought close to close to each other so that it forms a V shapes when the plates butt each
other.
3. Appropriate power supply should be given to the electrode and the work pieces.
4. Now the welding current output may be adjusted.
5. When current is passed, arc is produced between the electrode and work pieces.
6. Now set the two work pieces in correct position and maintain the gap 3mm and tag at
both ends of the work pieces as shown in figure.
7. Then the welding is carried out throughout the length.
8. As soon as the welding process is finished, switch off the current supply and allow the
work piece to cool.
9. Slag is removed by chipping process with the help of chipping hammer.
10. Finally using wire brush, welded portions are cleaned.

Result

Thus the required single V butt joint is made by arc welding process.

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 46 of 70




T - Joint













w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 47 of 70

Aim
To join the given two work pieces as a T joint by arc welding.

Material used
Mild Steel plates.
Tools required
Welding power supply Flat file
Welding rod Chipping hammer
Electrode holder Wire brush
Gloves and apron Earthing clamps
Shield and goggles

Procedure
1. First of all, the work pieces must be thoroughly cleaned to remove rust, scale and other
foreign materials.
2. Now the work pieces are placed on the table in such a way that two work pieces are
abroad close to each other T shapes are formed as shown in figure.
3. Appropriate power supply should be given to the electrode and the work pieces.
4. Now the welding current output may be adjusted.
5. When current is passed, arc is produced between the electrode and work pieces.
6. Now set the two work pieces in correct position like T joint and tag at both ends of the
work pieces as shown in figure.
7. The joint is placed on a welding table in a flat position by keeping the tag side down.
8. Then the welding is carried out throughout the work piece.
9. As soon as the welding process is finished, switch off the current supply and allow the
work piece to cool.
10. Slag is removed by chipping process with the help of chipping hammer.
11. Finally using wire brush, welded portions are cleaned.


Result
Thus the required T-joint is made by arc welding process.

w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 48 of 70


STUDY OF LATHE










w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 49 of 70



Aim
To study about the lathe


Introduction

Lathe is called the father of machine tools. The main function of lathe is to remove
metals from work piece to give a required shape and size. In the lathe the work piece is held in a
chuck. The tool is moved at an angle 90_ to the axis. Various operations such as straight turning,
taper turning, and chamfering, facing, knurling, grooving, thread cutting, taper turning are
carried out. When the operations above set are done automatically, then the lathe is called
automatic lathe.

Working principle of lathe
In a lathe, the work piece is held in chuck and rotates about its axis by means of power. A
single point cutting tool is mounted in tool post. When the chuck rotated the work piece also
rotated. The tool moves parallel to the axis of rotation of work piece to produce a cylindrical
surface, where as the tool moves perpendicular to the work piece to produce a flat surface. The
tool moves at an angle to the axis of work piece to produce a turn surface. The material is
removed in the form of chip from the work piece by giving proper feed and depth of cut. So,
there quire size and shape of the work is obtained.

Main parts of lathe

The lathe consists of various parts. Their parts and function are discussed below.

Bed

Bed is the base of the lathe. The headstock is mounted on the left end; the carriage is in
the middle and the tailstock at the right end of bed. The bed is made up of cast iron, alloyed with
nickel, chromium. The bed is made up of cast iron to observe shock and vibration created during
machining. The guide ways of the bed may be flatter inverted V shape.

Headstock

It is mounted on the left end of the bed. It carries a hollow spindle. The live center can be
attached in the spindle. The spindle nose is threaded. In chuck faceplates can be attached to the
spindle. The headstock may be back threaded type. The headstock has two types of driving
mechanism

Back geared mechanism
Belt driven mechanism
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 50 of 70






Tailstock

It is located on the bed at the right end. It is used for supports right end of work and also for
holding drills, reamer tools for drilling, reaming and such other operations. The tailstock can be
moved along the bed and clamped at any position, to support the different length work.

Carriage

Carriage is used for giving various feed to the tool by hand or by power. The carriage is
attached with the saddle.

Saddle

It is a H shaped casting fitted on the bed and moves along the guide ways. It carries the cross
slide, compound rest and a tool post.

i) Cross slide
It is attached to the upper side of saddle and carries compound slide and tool post. The cross
slide can be moved cross wise by hand or power. The micrometer dial is mounted on the cross
slide hand wheel, with an accuracy of 0.05mm.

ii) Compound Rest
It is attached over the cross slide. It is used during the taper turning opening operations to set the
tool for angular cuts. Here the micrometer dial is mounted to show the depth of cut.

iii) Tool post
The tool is clamped over the tool post. It is fixed over the compound rest. There are four
types of tool post
a. Single screw tool post
b. Open side tool post
c. Four bolt tool post
d. Four way tool post

Apron
Apron is attached to the saddle and hangs in front of the bed. It has gears, levers, clutchesfor
moving the carriage automatically. A split nut is attached for engaging and disengaging
thecarriage from the lead screw. It is used in thread cutting work.

Lead Screw
It is a longer screw with standard ACME square threads and used for transmitting power
for automatic feed for thread cutting operation.
w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 51 of 70


Feed rod
The feed rod is the long shaft used for the movement of carriage along the axis of bed. Itis used
for operations like facing, turning and boring.

Result
Thus the lathe was studied.







































w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 52 of 70




















w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 53 of 70



FACING, PLAIN TURNING AND DRILLING.

Aim

To perform turning, facing and chamfering on a cylindrical work piece.

Material used

Mild steel rod.

Tools required

Lathe
Three-jaw chuck
Chuck key
Vernier caliper
Single-point cutting tool
Procedure

1. First loosen the jaw in the chuck key to position the work piece, and then tighten the
J aws.
2. Fix the cutting tool in the tool post.
3. Switch on the lathe and move the carriage near to the work piece. Give it a small cross
feed, and then move carriage longitudinally to the required length slowly.
4. Bring the carriage to the original position, give a small cross feed and move carriage
Longitudinally. Repeat this step until required diameter is obtained.
5. To get smooth surface give a very small feed when the diameter is nearing the
required value.
6. To face the end surface of the work piece, move the carriage to make the tool touch
the end surface of the work piece.
7. Give a small feed in longitudinal direction, and then move the tool towards the axis of
the work piece using the cross slide to complete the work piece.
8. Using the proper drill pit to the required length make a blind hole.
Result
Thus the required shape and size is obtained by Facing, plain turning and drilling.



w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 54 of 70























w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 55 of 70


FACING, PLAIN TURNING AND TAPER TURNING

Aim

To perform turning, facing and chamfering on a cylindrical work piece.

Material used

Mild steel rod.

Tools required

Lathe
Three-jaw chuck
Chuck key
Vernier caliper
Single-point cutting tool
Procedure

1. First loosen the jaw in the chuck key to position the work piece, and then tighten the
J aws.
2. Fix the cutting tool in the tool post.
3. Switch on the lathe and move the carriage near to the work piece. Give it a small cross
feed, and then move carriage longitudinally to the required length slowly.
4. Bring the carriage to the original position, give a small cross feed and move carriage
Longitudinally. Repeat this step until required diameter is obtained.
5. To get smooth surface give a very small feed when the diameter is nearing the
required value.
6. To face the end surface of the work piece, move the carriage to make the tool touch
the end surface of the work piece.
7. Give a small feed in longitudinal direction, and then move the tool towards the axis of
the work piece using the cross slide to complete the work piece.
8. The turning operation is done with cutting tool to reduce the diameter up to the
required dimension for the two steps of various diameters.
9. The work piece is removed from the chuck and the dimensions of work piece are
checked for the requirements.

Result
Thus the required shape and size is obtained by Facing, plain turning and taper turning.


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 56 of 70


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 57 of 70

SHEET METAL

INTRODUCTION
Sheet metal works deals with working on the metal of 16-30 gauge ,with hand
tools and simple Machines. It is one of the major applications in engineering
industry. It has its own significance as useful trade in engineering work. Sheet
works such as making a tray, box , funnel, chimney, air duct, fabricate boiler shells
and pipe joints from thin or thick plates, etc. are few examples of its application.
For successful working in the trade, one should have a thorough knowledge of
projective geometry and development of surfaces.

SHEET METAL TOOLS
STEEL RULE: It is used to measure and mark dimensions. It is graduated on
both sides in millimeters and centimeters or inches.
DIVIDER: It is used in sheet metal jobs for circle making. With the divider we
can also do making the parts of the job.
Steel Square: It is used for checking the right angle of the jobs.
Trammel: It is used to draw large circles and arcs. This is also a marking tool
Wire Gauge: The thickness of sheet metal is referred in numbers known as
Standard Wire Gauge (SWG). The gaps in the circumference of the gauge are
used to check the gauge number


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 58 of 70


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 59 of 70

Bench Shear:
Sheet metal may be cut by shearing action. In this, the force is applied
through a compound lever, making it possible to cut sheet metal up to 4 mm thick.
Snips:
This tool is used for cutting thin metal sheets, before or after marking,
according to the jobs, is called snips. The straight snip is used for cutting along
outside curves and straight lines and curved snip or bent snip is for trimming along
inside curves.
Hammers:
Light weight hammers and mallets are used in sheet metal work. Ball-
peen Hammer has a cylindrical slightly curved face and a ball head. It is a general
purpose hammer used mostly for riveting in sheet metal work. The cross-peen
hammer and straight peen hammers are used for folding the sheet and to work in
the corners of the object.
Mallet:
Mallet is used for bending and folding work. It is called as soft hammer.
Generally, it is made of wood.
Stakes:
Stakes are nothing but anvils, which are used as supporting tools and to
form, seam, bend or rivet, sheet metal objects. They are made from wrought iron,
faced with steel.
Scriber:
This tool is used for making sheet metal jobs.
Punch:
Punch is used in sheet metal jobs for punching or deep marking.


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 60 of 70


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 61 of 70



w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 62 of 70


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 63 of 70



Ex. No : SHEET METAL TRAY Date :



Aim
To make a rectangular tray from the given sheet metal.

Material Required
G.I Sheet

Tools required
Steel rule
Mallet
Scriber
Divider
Protractor
Snips
Stakes
Ball peen hammer


Procedure
1. The size of the given sheet is checked for its dimension using steel rule.
2. Then the sheet is leveled on the leveling plate using a mallet.
3. The development procedure is followed the same as the square taper tray.
4. The dimensions are marked as shown in figure.
5. The sheet is cut as per the marked dimensions by straight snips.
6. Then a single hemming is made on the four sides of the tray as shown in figure.
7. The four sides of the tray bent to 90_ using the stakes anvil.
8. Finally all the corners of the tray are joined by riveting.




Result
Thus desired rectangular tray is made from the given sheet metal.





w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 64 of 70


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 65 of 70


Ex. No : MAKING OF A FUNNEL Date :



Aim
To make a funnel from the given sheet metal.

Tools required
Steel rule
Mallet
Scriber
Divider
Protractor
Snips
Stakes
Ball peen hammer
Solder

Procedure

1. The size of the given sheet is checked for its dimension using steel rule.
2. The required development of surface is being made on the white paper which is
overlapped on the sheet metal.
3. The marking is done on the sheet metal as per the development being done on the
paper.
4. Now using straight snips, unwanted material are removed.
5. Now fold and bend the workpiece to make the funnel shape and joint is made on the
workpieces.
6. Then using a groove, a locked grooved joint is made for about 5mm. also; hemming
is done in the bottom of the funnel.
7. In between top face and bottom face, a butt joint is made using a solder.
8. Finally, trimming and finishing operations are carried out.



Result

Thus desired funnel is made from the given sheet metal.


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 66 of 70


w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 67 of 70


Ex.no: Studying the working principle of Air conditioner Date:
Aim
The study of the window type air conditioner by dismantling and assembling the parts
sequentially.
Tools required
Spanner set
Procedure
1. Switch of the power supply and isolate the electrical connection from the system.
2. Remove the filter and grill from the system and place it on the work bench.
3. After checking and testing disconnect the circuit terminals from the operating control systems
such as thermostat, relay, capacitor, motor, selector switch and compressor terminals.
4. Remove the evaporator and condenser cover and dismantle the condenser and blower fan from
the motor from the motor shaft by the help of Allen key.
5. Remove the motor plates, clamps and clean the evaporator Condenser etc., with help of brush
and air blower.
6. Check the electrical parts and repair it if necessary.
7. Clean the motor and fix the fan and blower assembly properly to the motor.
8. Connect the electrical parts as per the circuit noted before and assemble all the parts.
9. Clean the outer cover of the Air conditioner and place it on the proper place.
10. Fix the grill& filter, and test the functioning of the air conditioner.
Result
Thus the air conditioner is studied by dismantling and assembling the parts sequentially.









w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 68 of 70
















w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 69 of 70


Ex.no: Date:
STUDYING THE WORKING PRINCIPLE OF CENTRIFUGAL PUMP
Aim
To study the centrifugal pump by dismantling and assembling the parts sequentially.
Tools Required
1. Die spanner set 2.Box spanner set
3. Bearing puller 4.Sledge hammer
5. Ball peen hammer 6.Tongs
Procedure
1. Remove the motor from the base plate by removing the pulley bolt and nut.
2. Remove the ump from base plate by unscrewing the base plate nut.
3. Remove the pulley by striking it with the hammer & dismantle the stuffing box flange.
4. Remove the outer cover of the vane by unscrewing the fasteners as well as the cotter pin.
5. Remove the vane mounted shaft by striking the shaft on the pulley side.
6. Remove the vane from the shaft by unscrewing the brass lock nut.
7. Remove the ball bearing from the bearing seat.
8. Clean all the removed parts.
9. Check the warned parts and replace it with new one.
10. Assemble the parts as per the above sequence in reverse direction.
Result
Thus the centrifugal pump is studied by dismantling and assembling the parts sequentially.








w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m
Sub Code: ME

Page 70 of 70

.





w
w
w
.
r
e
j
i
n
p
a
u
l
.
c
o
m

You might also like