You are on page 1of 43

P4M900-M7 FE Setup Manual

FCC Information and Copyright


This equipment has been tes ted and found to comply with the limits of a Class
B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed
to provide reasonable protec tion against harmful interference in a residential
installation. T his equipment generates , uses , and c an radiate radio frequency
energy and, if not ins talled and used in accordance with the instructions , may
cause harmful interference to radio communications . There is no guarantee
that interference will not occur in a particular ins tallation.

The vendor makes no representations or warranties with respec t to the


contents here and s pecially disclaims any implied warranties of merchantability
or fitness for any purpose. Further the vendor reserves the right to revise this
publication and to make c hanges to the c ontents here without obligation to
notify any party beforehand.
D uplication of this publication, in part or in whole, is not allowed without first
obtaining the vendors approval in writing.

The content of this users manual is subject to be c hanged without notice and
we will not be res ponsible for any mis takes found in this users manual. All the
brand and produc t names are trademarks of their respec tive companies .

Table of Contents
Chapter 1: Introduction.....................................................3
1.1
Before You Start................................................................... 3
1.2
Package Checklist................................................................ 3
1.3
Motherboard Features.......................................................... 4
1.4
Rear Panel Connectors.......................................................... 5
1.5
Motherboard Layout ............................................................ 6
Chapter 2: Hardware Installation........................................7
2.1
Installing Central Processing Unit (CPU) ................................ 7
2.2
Fan Headers......................................................................... 9
2.3
Installing System Memory.....................................................10
2.4
Connectors and Slots ............................................................12
Chapter 3: Headers & Jumpers Setup................................. 14
3.1
How to Setup Jumpers..........................................................14
3.2
Detail Settings.....................................................................14
Chapter 4: RAID Functions ............................................... 20
4.1
Operation System................................................................20
4.2
Raid Arrays.........................................................................20
4.3
How RAID Works.................................................................20
Chapter 5: Useful Help ..................................................... 22
5.1
Driver Installation Note .......................................................22
5.2
Award BIOS Beep Code........................................................23
5.3
Extra Information................................................................23
5.4
Troubleshooting...................................................................24
A ppendencies: SPEC In Other Language............................. 26
German................................................................................................26
France..................................................................................................28
Italian..................................................................................................30
Spanish ................................................................................................32
Portuguese...........................................................................................34
Polish...................................................................................................36
Russian ................................................................................................38
Arabic..................................................................................................40
Japanese ..............................................................................................42

P4M900-M7 FE

CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU ST ART
Thank you for choosing our product. Be fore you start installing the
mothe rboard, please make sure you follow the instructions be low:
Prepare a dry and stable work ing environment with
sufficie nt lighting.
Always disconne ct the compute r from powe r outle t
be fore ope ration.
Before you take the mothe rboard out from anti-static
bag, ground yourse lf prope rly by touching any safe ly
grounde d appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the compone nts on mothe rboard or the
rear side of the board unless ne cessary. Hold the board
on the edge , do not try to be nd or flex the board.

1.2

Do not leave any unfastene d small parts inside the


case afte r installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the compute r from dange rous a rea, such as hea t
source , humid air and wate r.

PACKAGE CHECKLIST
HDD Cable X 1
Installation Guide X 1
Fully Se tup Drive r C D X 1 (full ve rsion manual files inside )
Rear I/O Panel for ATX Case X 1
FDD Cable X 1 (optional)
Se rial ATA Cable X 1 (optional)
USB 2.0 Cable X1 (optional)
Se rial ATA Powe r Cable X 1 (optional)

Note: The package contents may differ by area or your motherboard version.

Motherboard Manual

1.3

MOT HERBOARD FEAT URES


SPEC
LGA 775
Intel Core2Duo/ Pe ntium 4 / Pentium Supports Hy per Thre ading/ Execute Disable Bit/

CPU

D / Celero n D / C eleron 4xx processor Enha nced Intel SpeedStep/ Intel Extended
up to 3.8 GHz

Memory 64 technology

*It is recommende d to use processors


with 95W power consumption.
FSB
Chipset
Graphic

Super I/O

533 / 800 / 1066 MHz


VIA P4M900
VIA VT8237A
Chrome9 HC 3D / 2D Graphics

Max Share d Vide o Memory is 256 MB

ITE 8712F

Enviro nment Co ntrol initiatives,

Provides the most commonly used

H/W Monitor

legacy Super I/O functionality.

Fan Spee d Co ntroller

Low Pin C ount Interface

ITE's "Smart Guardia n" function

DIMM Slots x 2
Main
Memory

Supports DDR2 533 / 667

Single Channel Mode DDR2 memory mo dule

Each DIMM supports

Registered DIMM and ECC DIMM is not supported

256/512MB/1GB/2GB DDR2
Max Memory C apicity 4GB

IDE

Integrated I DE Controller

SATA

Integrated Seri al ATA Controller

LAN PHY

Realtek RTL 8201CL PH Y

Sound
Codec

supports PIO Mo de 0~4,


Data transfer rates up to 1.5 Gb/s.
SATA Version 1.0 specification complia nt.
10 / 100 Mb/s auto negotiation
Half / Full duplex capability
5.1 cha nnels a udio o ut

ALC662
PCI Expr ess x 16 slot

Slots

Ultra DMA 33~133 B us Master Mode

High- Defi nition Audio s upport


x1

Supports PCI- E x 16 expa nsion cards

PCI Expr ess x 1 slot

x1

Supports PCI- E x 1 ex pansio n cards

PCI slot

x2

Supports PCI expa nsion cards

On Board

Floppy connector

x1

Each connector supports 2 Flo ppy drives

Connector

Printer Port C onnector

x1

Each connector supports 1 Pri nter port

IDE Co nnector

x2

Each connector supports 2 IDE device

SATA Connector

x2

Each connector supports 1 SATA devices

P4M900-M7 FE
SPEC
Front Pa nel Co nnector

Back Panel
I/O

x1

Supports front panel facilities

Front Audi o Co nnector

x1

Supports front panel a udio function

CD-in Co nnector

x1

Supports CD audio-in function

CPU Fan hea der

x1

CPU Fan power s upply (with Smart Fa n function)

System Fan hea der

x1

System Fan Power supply

Clear CMOS header

x1

Restore CMOS data to factory defa ult

USB connector

x2

Each connector supports 2 fr ont panel USB ports

Power Connector ( 24pi n)

x1

Connects to Power supply

Power Connector ( 4pin)

x1

Connects to Power supply

PS/2 Keyboard

x1

Connects to PS/ 2 Key board

PS/2 Mo use

x1

Connects to PS/ 2 Mo use

Serial Port

x1

Provide RS- 232 Serial connection

VGA Port

x1

Connects to mo nitor.

LAN port

x1

Connects to RJ- 45 ether net cable

USB Port

x4

Connects to USB devices

Audio J ack

x3

Provide Audio-In/Out a nd microphone co nnection

Board Size 190 mm (W) x 244 mm (L)


Special
Feature
OS
Support

1.4

Micro ATX Size Board

RAID 0 / 1 support

Windows 2000 / XP / VISTA

Biostar Reserves the right to a dd or r emove


support for any OS with or witho ut notice.

REAR PANEL CONNECT ORS


LAN

PS/2
Mouse

Li ne In/
Surround
Line Out
Mic In 1/
Bass/ Center

PS/2
Keyboard

COM1

VGA

USBX2

USBX2

Since the audio c hip s upports High Definiti on Audio Specific ation, the func tion of eac h audi o
jack c an be defined by software. T he input / output function of each audio jac k listed above
represents the default s etti ng. However, when c onnecti ng exter nal microphone to the audio
port, pleas e us e the Line In (blue) and Mic In (Pink) audio j ac k.

Motherboard Manual

1.5

MOT HERBOARD LAYOUT


JCFAN1

JKBMS1

COM1
JCOM1

LGA775
CPU1

DIMM1

JVGA1

JPRNT1

JUSB1

DIMM2

JATXPWR1

JUSBV1

IDE1

P4M900

JUSBLAN1

IDE2

JATXPWR2

LAN
JAUDIO1
PCI-EX16

Super
I/O

PCI-EX1_1

BAT1
BIOS

JSATA2

JU SB2

VIA
VT8237A

PCI1
JCDIN1

JSATA1

JUSB3

PCI2

JUSBV2

JCMOS1

Codec
JAUDIOF1

FDD1

JSFAN1
JPAN EL 1

Not e: represe nts the 1st pin.


6

P4M900-M7 FE

CHAPTER 2: HARDWARE INSTALLATION


2.1 INST ALLING CENT RAL PROCESSING UNIT (CPU)

Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs wont be damaged.

Pin Cap

Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.

Motherboard Manual
Step 2: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 2-1:

Step 2-2:

Step 3: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.

Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the JCFAN1. This completes the installation.

P4M900-M7 FE

2.2

FAN HEADERS

These fan headers support cooling-fans built in the computer. The fan
cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to
pin#1.

JCFAN1: CPU Fan Heade r

Pin
1
2
3
4

Assignment
Ground
+12V
FAN RPM rate
sense
Smart Fan
Control

JSFAN1: System Fan He ader

Pin
1
2
3

Assignment
Ground
+12V
FAN RPM rate
sense

Note:
The JSFAN1 supports 3-pin head connector and the JCFAN1 supports 4-pin head
connector. When connecti ng with wires onto connectors, pl ease note that the r ed wire is
the positi ve and should be connected to pin#2, and the black wire is Ground and should
be connected to GND.

Motherboard Manual

2.3

INST ALLING SYST EM MEMORY

DIMM1
DIMM2

A. Memory Modules

1.

10

Unlock a DIMM slot by pressing the retaining clips outward. Align a


DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.

P4M900-M7 FE
2.

Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.

B. Memory Capacity
DIMM Socket
Location
DIMM1

256MB/512MB/1GB/2GB

DIMM2

256MB/512MB/1GB/2GB

DDR Module

Total Memory
Size
Max is 4GB.

11

Motherboard Manual

2.4

CONNECT ORS AND SLOT S

FDD1: Floppy Disk Conne ctor


The motherboard prov ides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk ty pes. This connector supports the
prov ided f loppy drive ribbon cable.

34

33

IDE1/IDE2: Hard Disk Conne ctors


The motherboard has a 32-bit Enhanced PCI IDE Controller that prov ides PIO
Mode 0~4, Bus Master, and Ultra DMA 33/66/100/133 f unctionality. It has two
HDD connectors: IDE1 (primary ) and IDE2 (secondary ).
The IDE connectors can connect a master and a slav e driv e, so you can
connect up to four hard disk drives. The f irst hard drive should always be
connected to IDE1.

40

39

IDE1

12

IDE2

P4M900-M7 FE

PCI-EX16: PCI-Express x16 Slot


-

PCI-Express 1.0a compliant.

Maximum theoretical realized bandwidth of 4GB/s simultaneously per


direction, f or an aggregate of 8GB/s totally.

PCI-EX1_1: PCI-Express x1 Slot


-

PCI-Express 1.0a compliant.

Data transf er bandwidth up to 250MB/s per direction; 500MB/s in total.


PCI-Express supports a raw bit-rate of 2.5Gb/s on the data pins.
2X bandwidth ov er the traditional PCI architecture.

PCI-EX16

PCI-EX1_1

PCI1/PCI2: Pe riphe ral Component Inte rconne ct Slots


This motherboard is equipped with 2 standard PCI slots. PCI stands f or
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.

PCI1
PCI2

13

Motherboard Manual

CHAPTER 3: HEADERS & JUMPERS SETUP


3.1 HOW T O SET UP JUMPERS
The illustration shows how to set up jumpers. When the jumper cap is
placed on pins, the jumper is close, if not, that means the jumper is
open.

Pin opened

3.2

Pin closed

Pin1-2 closed

DET AIL SETT INGS

JPANEL1: Front Panel Heade r


This 16-pin connector includes Power-on, Reset, HDD LED, Power LED, and
speaker connection. It allows user to connect the PC cases front panel switch
f unctions.

PWR_LED
On/Off
++ -

9
1

+ SPK

Pin
1
2
3
4
5
6
7
8

14

Assignment
+5V
N/A
N/A
Speaker
HDD LED (+)
HDD LED (-)
Ground
Reset control

Functio n
Speaker
Connector
Hard drive
LED
Reset button

Pin
9
10
11
12
13
14
15
16

16
8

RST
HLED

Assignment
N/A
N/A
N/A
Power LED (+)
Power LED (+)
Power LED (-)
Power button
Ground

Functio n
N/A
N/A
Power LED
Power-on button

P4M900-M7 FE

ATX Powe r Source Conne ctor: JATXPWR1


JATXPWR1 allows user to connect 24-pin power connector on the ATX power
supply.
12

24

13

Pin

Assignment

Pin

Assignment

13
14
15
16
17
18
19
20
21
22
23
24

+3.3V
-12V
Ground
PS_ON
Ground
Ground
Ground
NC
+5V
+5V
+5V
Ground

1
2
3
4
5
6
7
8
9
10
11
12

+3.3V
+3.3V
Ground
+5V
Ground
+5V
Ground
PW_OK
Standby Voltage+5V
+12V
+12V
+3.3V

JATXPWR2: ATX Powe r Source Conne ctor


By connecting this connector, it will provide +12V to CPU power circuit.

Pin
1
2
3
4

Assignment
+12V
+12V
Ground
Ground

15

Motherboard Manual

JUSB2/JUSB3: Heade rs for USB 2.0 Ports at Front Panel

This header allows user to connect additional USB cable on the PC f ront panel,
and also can be connected with internal USB devices, like USB card reader.

10

JUSB2

JUSB3

Pin
1
2
3
4
5
6
7
8
9
10

Assignment
+5V (fused)
+5V (fused)
USBUSBUSB+
USB+
Ground
Ground
Key
NC

JSATA1/JSATA2: Se rial ATA Conne ctors

The motherboard has a PCI to SATA Controller with 2 channels SATA interf ace,
it satisfies the SATA 1.0 spec and with transfer rate of 1.5Gb/s.

JSATA2
7

Pin
1
2
3
4
5
6
7

Assignment
Ground
T X+
T XGround
RXRX+
Ground

JSATA1

JAUDIO F1: Front Panel Audio Heade r

This header allows user to connect the front audio output cable with the PC f ront
panel. This header allows only HD audio front panel connector; AC97 connector
is not acceptable.

16

10

Pin
1
2
3
4
5
6
7
8
9
10

Assignment
Mic Left in
Ground
Mic Right in
GPIO
Right line in
Jack Sense
Front Sense
Key
Left line in
Jack Sense

P4M900-M7 FE

JCDIN1: CD-RO M Audio-in Connector


This connector allows user to connect the audio source f rom the v ariaty dev ices,
like CD-ROM, DVD-ROM, PCI sound card, PCI TV turner card etc.

Assignment
Left Channel Input
Ground
Ground
Right Channel Input

Pin
1
2
3
4

JCMO S1: Cle ar CMOS Heade r


By placing the jumper on pin2-3, it allows user to restore the BIOS saf e setting
and the CMOS data, please carefully f ollow the procedures to avoid damaging
the motherboard.
1

Pin 1-2 Close:


Normal Operation (default).

3
Pin 2-3 Close:
Clear CMOS data.

Clear CMOS Proce dures:


1.
2.
3.
4.
5.
6.

Remov e AC power line.


Set the jumper to Pin 2-3 close.
Wait f or f ive seconds.
Set the jumper to Pin 1-2 close.
Power on the AC.
Reset y our desired password or clear the CMOS data.

17

Motherboard Manual

JPRNT1: Printe r Port Connector


This header allows you to connector printer on the PC.

25

Pin
1
2
3
4
5
6
7
8
9
10
11
12
13

18

Assignment
-Strobe
-ALF
Data 0
-Error
Data 1
-Init
Data 2
-Scltin
Data 3
Ground
Data 4
Ground
Data 5

Pin
14
15
16
17
18
19
20
21
22
23
24
25
26

Assignment
Ground
Data 6
Ground
Data 7
Ground
-ACK
Ground
Busy
Ground
PE
Ground
SCLT
Key

P4M900-M7 FE

JUSBV1/JUSBV2: Powe r Source Heade rs for USB Ports


Pin 1-2 Close:
JUSBV1: +5V for USB ports at JUSB1/JUSBLAN1.
JUSBV2: +5V for USB ports at f ront panel (JUSB2/JUSB3).
Pin 2-3 Close:
JUSBV1: USB ports at JUSB1/JUSBLAN1 are powered by +5V standby
v oltage.
JUSBV2: USB ports at front panel (JUSB2/JUSB3) are powered by +5V
standby v oltage.
1

JUSBV1
1

Pin 1-2 close

JUSBV2

Pin 2-3 close

Note:
In order to support this function Power-On system via USB device, JUSBV1/ JUSBV2
jumper cap should be placed on Pin 2-3 indi viduall y.

19

Motherboard Manual

CHAPTER 4: RAID FUNCTIONS


4.1 O PERAT ION SYST EM
z

Supports Windows XP Home/Prof essional Edition, and Windows 2000 Prof essional.

4.2

RAID ARRAYS

RAID supports the following types of RAID arrays:


RAID 0: RAID 0 defines a disk striping scheme that improves disk read and write times for
many applications.
RAID 1: RAID 1 defines techniques for mirroring data.

4.3

HOW RAID WORKS

RAID 0:
The controller stripes data across multiple drives in a RAID 0 array system. It breaks
up a large file into smaller blocks and performs disk reads and writes across multiple
drives in parallel. The size of each block is determined by the stripe size parameter,
which you set during the creation of the RAID set based on the system environment. This
technique reduces overall disk access time and offers high bandwidth.

Features and Benefits

Drives: Minimum 1, and maximum is up to 6 or 8. Depending on the


platf orm.
Uses: Intended for non-critical data requiring high data throughput, or any
env ironment that does not require f ault tolerance.
Benefits: prov ides increased data throughput, especially f or large files. No
capacity loss penalty f or parity.
Drawbacks: Does not deliver any fault tolerance. If any drive in the array
f ails, all data is lost.
Fault Tolerance: No.

Blo ck 1
Block 3
Block 5

20

Block 2
Block 4
Block 6

P4M900-M7 FE

RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on a
second redundant drive in the array. RAID 1 provides a hot-standby copy of data if the
active volume or drive is corrupted or becomes unavailable because of a hardware failure.
RAID techniques can be applied for high-availability solutions, or as a form of automatic
backup that eliminates tedious manual backups to more expensive and less reliable
media.

Features and Benefits

Drives: Minimum 2, and maximum is 2.


Uses: RAID 1 is ideal f or small databases or any other application that
requires f ault tolerance and minimal capacity.
Benefits: Prov ides 100% data redundancy. Should one driv e f ail, the
controller switches to the other drive.
Drawbacks: Requires 2 driv es for the storage space of one driv e.
Perf ormance is impaired during driv e rebuilds.
Fault Tolerance: Yes.

Block 1
Block 2
Block 3

Block 1
Block 2
Block 3

21

Motherboard Manual

CHAPTER 5: USEFUL HELP


5.1 DRIVER INST ALLAT ION NOT E
After you installed your operating system, please insert the Fully Setup
Driver CD into your optical drive and install the driver for better system
performance.
You will see the following window after you insert the CD

The setup guide will auto detect your motherboard and operating system.
Note:
If this window didnt show up after you insert the Driver CD, please use file browser to
locate and execute the file SETUP.EXE under your optical drive.

A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.

B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.

C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat Reader to open the manual file. Please download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep 2.html
22

P4M900-M7 FE

5.2

AWARD BIOS BEEP CODE

Beep Sound
One long beep followed by two short
beeps
High-low siren sound

Meaning
Video card not found or v ideo card
memory bad
CPU overheated
System will shut down automatically
One Short beep when system boot-up No error found during POST
Long beeps every other second

5.3

No DRAM detected or install

EXT RA INFORMAT ION

CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
When the CPU is over heated, the motherboard will shutdown
automatically to avoid a damage of the CPU, and the system may not
power on again.
In this case, please double check:
1. The CPU cooler surface is placed evenly with the CPU surface.
2. CPU fan is rotated normally.
3. CPU fan speed is fulfilling with the CPU speed.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See Close CMOS Header: JCMOS1 section)
2. Wait for seconds.
3. Power on the system again.

23

Motherboard Manual

5.4

TROUBLESHOOT ING

Probable
Solution
1.
Make sure power cable is
No power to the system at all
securely plugged in.
Power light dont illuminate, f an
inside power supply does not turn 2.
Replace cable.
on.
3.
Contact technical support.
2.
Indicator light on key board does
not turn on.
System inoperativ e. Keyboard lights
Using even pressure on both ends of
are on, power indicator lights are lit,
the DIMM, press down firmly until the
and hard driv e is spinning.
module snaps into place.
1.

System does not boot from hard disk


1.
driv e, can be booted f rom optical driv e.

Check cable running from disk to


disk controller board. Make sure
both ends are securely plugged
in; check the driv e type in the
standard CMOS setup.
2.
Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
1.
Back up data and applications
System only boots f rom optical driv e.
f iles.
Hard disk can be read and applications
can be used but booting from hard disk 2.
Ref ormat the hard driv e.
is impossible.
Re-install applications and data
using backup disks.
Screen message says Invalid
Rev iew systems equipment. Make sure
Conf iguration or CMOS Failure.
correct inf ormation is in setup.
Cannot boot system after installing
1.
Set master/slave jumpers
second hard driv e.
correctly.
2.
Run SETUP program and select
correct driv e types. Call the drive
manuf acturers f or compatibility
with other drives.

24

P4M900-M7 FE

This page is intentionally left blank.

25

Motherboard Manual

APPENDENCIES: SPEC IN OTHER LANGUAGE


GERMAN
Spezifikationen
LGA 775
Intel Core2Duo/ Pe ntium 4 / Pentium Untersttzt Hyper -Threadi ng / Execute Disable Bit
CPU

D / C eleron D / Celer on 4xx

/ Enha nced I ntel Spee dStep / Intel

Prozessoren mit bis zu 3,8 GHz

Architecture-64 / Exte nde d Memory 64

*It is recommende d to use processors Technol ogy


with 95W power consumption.
FSB
Chipsatz
Grafik

Super E/A

533 / 800 / 1066 MHz


VIA P4M900
VIA VT8237A
Chrome9 HC 3D / 2D Graphics

Max. 256MB gemeinsam benutzter Videospeicher

ITE 8712F

Umgebungskontrolle,

Bietet die hufi g verwe ndete n alte n

Hardware-berwachung

Super E/A-Funktione n.

Lfterdre hzahl-Co ntroller

Low Pin C ount-Schnittstelle

"Smart Guar dian" -Funktion v on ITE

DDR2 DIMM-Steckpltze x 2
Arbeitsspe
icher

Untersttzt DDR2 533 / 667

Ein-Kanal DDR2 S peichermodul

Jeder DIMM untersttzt

registrierte DIMMs. ECC DIMMs werde n nicht

256/512MB/1GB/2GB DDR2.

untersttzt.

Max. 4GB Ar beitsspeicher


Ultra DMA 33 / 66 / 100 / 133Bus Master-Modus

IDE

Integrierter IDE-Co ntroller

SATA

Integrierter Serial ATA-Controller

LAN PHY

Realtek RTL 8201CL PH Y

Audio-Cod
ec
Steckpltz
e

Untersttzt PIO-Modus 0~4,


Datentransferr ate bis zu 1.5Gb/s
Konform mit der SATA-Spezifikation Version 1.0.
10 / 100 Mb/s A uto-Negotiation
Halb-/ Vollduplex- Funktion
Untersttzt High- Definitio n Audio

ALC662

5.1-Kanal-Audioausgabe

PCI-Steckplatz

x2

PCI Expr ess x16 Steckplatz

x1

PCI Expr ess x 1-Steckplatz

x1

Onboard-A Diskettenlaufwerk anschluss

x1

nschluss

26

Jeder Anschluss untersttzt 2 Diskettenlaufwerke

Druckeranschluss Anschluss

x1

Jeder A nschluss untersttzt 1 Druckera nschluss

IDE-Anschluss

x2

Jeder A nschluss untersttzt 2 IDE-L aufwerk e

P4M900-M7 FE
Spezifikationen

Rckseiten
-E/A

Platinengr
e.
Sonderfun
ktionen
OS-Unters
ttzung

SATA-Anschluss

x2

Jeder A nschluss untersttzt 1 SATA-Laufwerk

Fronttafela nschluss

x1

Untersttzt die Fro nttafelfunktio nen

Front-Audioa nschluss

x1

Untersttzt die Fronttafel-Audioa nschlussfunktion

CD-IN-Anschluss

x1

CPU-Lfter-Sockel

x1

System-Lfter-Sockel

x1

"CMOS lschen"-Sockel

x1

USB-Anschluss

x2

Stromanschluss (24- polig)

x1

Stromanschluss (4-poli g)

x1

PS/2-Tastatur

x1

PS/2-Maus

x1

Serieller Anschluss

x1

VGA-Anschluss

x1

LAN-Anschluss

x1

USB-Anschluss

x4

Audioanschluss

x3

Untersttzt die CD Audio-I n-Funktion


CPU-Lfterstromversorgungsanschl uss (mit
Smart Fan-Funktion)
System-Lfter-Stromversorgungsa nschluss

Jeder A nschluss untersttzt 2


Fronttafel-USB-Anschlsse

190 mm (B) X 244 mm (L)

Untersttzt RAID 0 / 1
Biostar behlt sich das Recht v or, ohne
Windows 2K / XP / VISTA

Ankndigung die Untersttzung fr ei n


Betriebssystem hinzuzufgen oder zu entferne n.

27

Motherboard Manual

FRANCE
SPEC
LGA 775
Processeurs Intel Core2Duo / P entium 4 /
UC

Pentium D / Celeron D / Celer on 4xx


jusqu' 3,8 GHz
*It is recommende d to use processors
with 95W power consumption.

Prend en charge les technologies


Hyper -Thre ading / d'ex cution de bit de
dsactivation / I ntel Spe edStep optimise/
d'architecture Intel 64 / de mm oire te ndue
64

Bus frontal 533 / 800 / 1066 MHz


Chipset
Graphi que
s

Super E/S

Mmoire
principale

VIA P4M900
VIA VT8237A
Chrome9 HC 3D / 2D Graphics

Mmoire vid o partage maximale de 256 Mo

ITE 8712F

Initiatives de co ntrle e nvironnementales,

Fournit la fo nctionnalit de Super E/S

Moniteur de matriel

patrimoniales la plus utilise.

Contrleur de vitesse de ventilateur

Interface faible compte de broc hes

Fonction " Gardie n i ntelligent" de l'ITE

Fentes DDR 2 DIMM x 2

Module de mm oire DDR2 mo de simple

Prend en charge la DDR 2 533 / 667

voie

Chaque DIMM prend e n charge des

Les DIMM r egistres et DIMM avec code

DDR2 de 256 M o / 512 Mo / 1Go / 2 Go correcteurs d'erreurs ne so nt pas prises en


Capacit mmoire maximale de 4 Go

charge

Contrleur IDE intgr

/ 133

Mode principale de Bus Ultra DMA 33 / 66 / 100


IDE

Prend en charge le mode PIO 0~4,


SATA

Contrleur Serial ATA intgr :

LAN PHY

Realtek RTL 8201CL PH Y

Codec
audio

Fentes

Connecteu
r
embarqu

28

Taux de transfert jusqu' 1.5 Go/s.


Conforme la spcification SATA Version 1.0
10 / 100 Mb/s ngociation a utomatique
Half / Full duplex capability
Prise en c harge de l'audio haute d finition

ALC662

Sortie audio 5.1 voies

Fente PCI

x2

Slot PCI Ex press x16

x1

Slot PCI Ex press x 1

x1

Connecteur de disquette

x1

Connecteur de P ort d'imprimante x1

Chaque connector pre nd en charge 2 lecteurs


de disquettes
Chaque connector pre nd en charge 1 Port
d'imprimante

P4M900-M7 FE
SPEC
Connecteur IDE

x2

Connecteur SATA

x2

Connecteur du pa nne au avant

x1

Connecteur Audio du panneau ava nt x1

Connecteur d'entr e CD

x1

Embase de ve ntilateur UC

x1

Embase de ve ntilateur systme x1


Embase d'e ffacement CMOS

x1

Connecteur USB

x2

Connecteur d'alimentatio n

x1

Chaque connecteur prend e n char ge 2


priphri ques I DE
Chaque connecteur prend e n char ge 1
priphri que SATA
Prend en charge les quipements du panneau
avant
Prend en charge la fo nction a udio du panneau
avant
Prend en charge la fo nction d'entre audio de
CD
Alimentation lectrique du ve ntilateur UC
(avec fo nction de v entilateur intellige nt)
Alimentation lectrique du ve ntilateur systme

Chaque connecteur prend e n char ge 2 ports


USB de panneau ava nt

(24 broches)
Connecteur d'alimentatio n

x1

(4 br oches)
Clavier PS/2

x1

Souris PS/2

x1

E/S du

Port srie

x1

panneau

Port VGA

x1

arrire

Port LAN

x1

Port USB

x4

Fiche audio

x3

Dimension
s de la

190 mm (l) X 244 mm (H)

carte
Fonctionna
lits

Prise en c harge RAID 0 / 1

spciales
Support
SE

Biostar se rserve le droit d'ajo uter o u de


Windows 2K / XP / VISTA

supprimer le support de SE avec o u sa ns


pravis.

29

Motherboard Manual

IT ALIAN
SPECIFICA
LGA 775
Processore Intel Core 2Duo/ Pentium 4 / Supporto di Hyper -Threadi ng / Ex ecute Disable
CPU

Pentium D / Celer on D / Celeron 4xx fino Bit / Enhance d I ntel Spee dStep /
a 3.8 GHz

Architettura Intel 64 / Tecnologi a Extende d

*It is recommende d to use processors

Memory 64

with 95W power consumption.


FSB
Chipset

Grafica

533 / 800 / 1066 MHz


VIA P4M900
VIA VT8237A
La memoria vi deo co ndivisa massima di

Chrome9 HC 3D / 2D Graphics

256MB
Funzioni di co ntrollo dellambiente:

ITE 8712F
Super I/O

Fornisce le funzionalit le gacy Super I/O Monitoraggio hardware


usate pi comunemente.

Controller velocit ventolina

Interfaccia LPC (L ow Pin Count)

Funzione "Smart Guardi an" di I TE

Alloggi DIMM DDR 2 x 2


Memoria
principale

Modulo di memoria DDR2 a canale singolo

Supporto di DDR2 533 / 667

Ciascun DIMM supporta DDR 2 256MB / DIMM registrati e DIMM ECC no n sono
supportati

512MB / 1GB / 2GB


Capacit massima della memori a 4GB

Modalit B us Master Ultra DMA 33 / 66 / 100 /


IDE

Controller IDE i ntegrato

133
Supporto modalit PIO Mode 0- 4
Velocit di trasferimento dei dati fi no a 1.5

SATA

Controller Serial ATA inte grato

Gb/s.
Compatibile specifiche SATA Versione 1.0.

LAN PHY
Codec
audio

30

Uscita audio 5.1 canali


x2

Alloggio PCI Ex press x16

x1

Alloggio PCI Ex press x1

x1

Connettori Connettore flo ppy


su scheda

Capacit Half / Full Duplex


Supporto audio High-Definition (HD)

ALC662
Alloggio PCI

Alloggi

Negoziazione automatica 10 / 100 Mb/s

Realtek RTL 8201CL PH Y

x1

Connettore Porta stampa nte

x1

Connettore IDE

x2

Ciascun connettore supporta 2 unit Floppy


Ciascun connettore supporta 1 P orta
stampante
Ciascun connettore supporta 2 unit IDE

P4M900-M7 FE
SPECIFICA
Connettore SATA

x2

Connettore pa nnello fro ntale

x1

Ciascun connettore supporta 1 unit SATA


Supporta i servizi del pa nnell o fr ontale

Connettore audio frontale

x1

Supporta la funzione audi o pannello frontale

Connettore CD-in

x1

Supporta la funzione i nput audio C D

Collettore ventolina CPU

x1

Collettore ventolina sistema

x1

Collettore cancellazione CMOS

x1

Connettore USB

x2

Connettore alimentazione

x1

Alimentazione ve ntolina CPU (co n funzione


Smart Fan)
Alimentazione ve ntolina di sistema

Ciascun connettore supporta 2 porte USB


pannello frontale

(24 pin)
Connettore alimentazione

x1

(4 pi n)
Tastiera PS/2

x1

Mouse PS/2

x1

I/O

Porta seriale

x1

pannello

Porta VGA

x1

posteriore Porta LAN

x1

Dimension
i scheda

Porta USB

x4

Connettore audio

x3

190 mm (lar ghezza) x 244 mm (altezza)

Caratterist
iche

Supporto RAID 0 / 1

speciali
Sistemi
operativi
supportati

Biostar si riserva il diritto di aggiungere o


Windows 2K / XP / VISTA

rimuovere il supporto di qualsiasi sistema


operativo se nza pre avviso.

31

Motherboard Manual

SPANISH
Especificacin
LGA 775
Procesador I ntel Core 2Duo / Penti um Admite Hyper -Threadi ng / Bit de deshabilitacin
CPU

4 / Pentium D / Celero n D / Celero n

de ejecuci n / Intel SpeedStep Me jorado / Intel

4xx hasta 3,8 GHz

Architecture-64 / Tecnolog a Extended Memor y

*It is recommende d to use processors 64


with 95W power consumption.
FSB

533 / 800 / 1066 MHz

Conjunto

VIA P4M900

de chips

VIA VT8237A

Grficos

Chrome9 HC 3D / 2D Graphics

Memoria mxima de vdeo compartida de 256MB

ITE 8712F

Iniciativas de control de entor no,

Le ofrece las funcionalidades


Sper E/S hereda das de uso ms comn Sper
E/S.

Monitor hardware
Controlador de velocida d de ve ntilador
Funcin "Guardia intelige nte" de I TE

Interfaz de cue nta Low Pin


Ranuras DIMM DDR 2 x 2
Admite DDR2 de 533 / 667
Memoria

Cada DIMM admite DDR de 256MB

principal

/512MB /1GB / 2GB


Capacidad mxima de memoria de

Mdulo de memoria DDR2 de canal Sencillo


No admite DIMM re gistrados o DIMM compatibl es
con ECC

4GB
IDE

Controlador IDE inte grado

SATA

Controlador ATA Serie Integra do

Red Local

Realtek RTL 8201CL PH Y

Cdecs de
sonido

Ranuras

Conectore
s en placa

32

Modo bus maestro Ultra DMA 33 / 66 / 100 / 133


Soporte los Mo dos PIO 0~4,
Tasas de transfere ncia de hasta 1.5 Gb/s.
Compatible con la versin SATA 1.0.
Negociacin de 10 / 100 Mb/s
Funciones Half / F ull dplex
Soporte de soni do de Alta Defi nicin

ALC662

Salida de sonido de 5.1 canales

Ranura PCI

X2

Ranura PCI Ex press x16

X1

Ranura PCI ex press x 1

X1

Conector disco flexible

X1

Conector Puerto de impresora

X1

Cada conector soporta 1 Puerto de impresora

Conector IDE

X2

Cada conector soporta 2 dispositivos IDE

Conector SATA

X2

Cada conector soporta 1 dispositivos SATA

Cada conector soporta 2 uni dades de disco


flexible

P4M900-M7 FE
Especificacin
Conector de pa nel fro ntal

X1

Soporta instalaciones en el panel fr ontal

Conector de sonido frontal

X1

Soporta funcio nes de sonido e n el pa nel frontal

Conector de entra da de C D

X1

Soporta funci n de e ntrada de sonido de CD

Cabecera de ve ntilador de C PU

X1

Fuente de alime ntacin de ve ntilador de CPU (con


funci n Smart Fan)

Cabecera de ve ntilador de
sistema

X1

Cabecera de borrado de CMOS

X1

Conector USB

X2

Conector de alimentacin

X1

Fuente de alimentacin de ventilador de sistema

Cada conector soporta 2 puertos USB fro ntales

(24 patillas)
Conector de alimentacin

X1

(4 patillas)
Teclado PS/2

Panel

Ratn PS/2

X1

Puerto serie

X1

trasero de Puerto VGA


E/S

Tamao de
la placa
Funciones
especiales

Puerto de re d local

operativo

X1
X1

Puerto USB

X4

Conector de sonido

X3

190mm. (A) X 244 Mm. (H)

Admite RAID 0 / 1

Soporte de
sistema

X1

Windows 2K / XP / VISTA

Biostar se reserva el derecho de aa dir o r etirar el


soporte de cualquier SO con o sin aviso previo.

33

Motherboard Manual

PORT UGUESE
ESPECIFICAES
LGA 775
Processador Intel Core2Duo / Pe ntium 4 Suporta as tecnologias Hyper -Threa ding /
CPU

/ Pentium D / Celer on D / Celero n 4xx

Execute Disable Bit / Enha nced I ntel

at 3,8 GHz

SpeedStep / Intel Arquitecture -64 /

*It is recommende d to use processors

Extende d Memor y 64

with 95W power consumption.


FSB
Chipset
Placa
grfica

533 / 800 / 1066 MHz


VIA P4M900
VIA VT8237A
Chrome9 HC 3D / 2D Graphics

Memria de vde o mxima partilha da: 256 MB

ITE 8712F
Especifica Proporciona as funcionalida des mais
o Super

utilizadas em termos da especificao

I/O

Super I/O.

Iniciativas para control o do am biente


Monitorizao do hardware
Controlador da velocida de da v entoinha
Funo "Smart Guardia n" da I TE

Interface LPC (Low Pi n Co unt).


Ranhuras DIMM DDR2 x 2
Suporta m dulos DDR2 533 / 667
Memria

Cada m dulo DIMM suporta uma

principal

memria DDR 2 de 256MB /512 MB / 1


GB / 2GB

Mdulo de memria DDR2 de canal simples


Os mdulos DIMM r egistados e os DIMM ECC
no so suportados

Capacidade mxima de memria : 4 GB


IDE

Modo Bus master Ultra DMA 33 / 66 / 100 / 133

Controlador IDE inte grado

Suporta o modo PIO 0~4,


Velocidades de transmisso de dados at 1.5

SATA

Gb/s.

Controlador Serial ATA integra do

Compatibilidade com a especificao SATA


verso 1.0.

LAN PHY
Codec de
som

Ranhuras

Auto ne gociao de 10 / 100 MB/s

Realtek RTL 8201CL PH Y

Capacidade semi/full- duplex


Suporta a especificao High-De finition Audi o

ALC662

Sada de udio de 5.1 ca nais

Ranhura PCI

x2

Ranhura PCI Express x 16

x1

Ranhura PCI Express x 1

x1

Conectore Conector da unida de de disquetes x 1

Cada co nector suporta 2 unida des de disquetes

s na placa Conector da para impressora

Cada conector suporta 1 Porta para impr essora

34

x1

P4M900-M7 FE
ESPECIFICAES
Conector IDE

x2

Cada conector suporta 2 dispositivos IDE

Conector SATA

x2

Cada conector suporta 1 dispositivo SATA

Conector do pai nel fro ntal

x1

Conector de udio fro ntal

x1

Suporta a funo de udio no painel fr ontal

Conector para e ntrada de C Ds

x1

Suporta a e ntrada de udi o a partir de C Ds

Conector da ve ntoinha da CPU

x1

Conector da ve ntoinha do
sistema

x1

Para suporte de vrias funes no painel


frontal

Alimentao da ventoi nha da CPU (com a


funo Smart Fan)
Alimentao da ventoi nha do sistema

Conector para limpeza do CMOS x1


Conector USB

x2

Conector de alimentao

x1

Cada conector suporta 2 portas USB no pai nel


frontal

(24 pinos)
Conector de alimentao

x1

(4 pi nos)
Teclado PS/2
Entradas/
Sadas no
painel
traseiro

Tamanho
da pl aca

x1

Rato PS/2

x1

Porta srie

x1

Porta VGA

x1

Porta LAN

x1

Porta USB

x4

Tomada de udio

x3

190 mm (L) X 244 mm (A)

Caracterst
icas

Suporta as funes RAID 0 / 1

especiais
Sistemas
operativos
suportado
s

A Biostar reserva-se o direito de adicionar ou


Windows 2K / XP / VISTA

remover suporte par a qualquer sistema


operativo com ou sem aviso prvio.

35

Motherboard Manual

POLISH
SPEC
LGA 775
Procesor Intel Cor e2Duo/ Penti um 4 /
Procesor

Obsuga Hyper -Threa ding / Execute Disa ble Bit

Pentium D / Celeron D / Celer on 4xx do / Enha nced I ntel Spee dStep / Intel
3,8 GHz

Architecture-64 / Exte nde d Memory 64

*It is recommende d to use processors

Technol ogy

with 95W power consumption.


FSB
Chipset

Grafika

533 / 800 / 1066 MHz


VIA P4M900
VIA VT8237A
Maks. wielko wspdzielonej pamici video

Chrome9 HC 3D / 2D Graphics

wynosi 256MB

Gniazda DDR 2 DIMM x 2


Pami
gwna

Modu pamici DDR2 z trybem poje dynczego

Obsuga DDR2 533 / 667

Kade gniazdo DIMM obsuguje mo duy kanau


256MB /512MB / 1GB / 2GB DDR2

Brak obsugi Registered DIMM or az ECC DIMM

Maks. wielko pamici 4GB

Super I/O

ITE 8712F

Funkcje kontroli warunkw prac y,

Zapewnia najbardziej powszechne

Monitor H/W

funkc je Super I/O.

Kontroler pr dkoci wentylatora

Interfejs L ow Pin Count

Funkcja ITE "Smart Guar dian"


Ultra DMA 33 / 66 / 100 / 133 Tryb B us Master

IDE

Zintegrowany kontroler IDE

SATA

Zintegrowany kontroler Serial ATA

obsuga PIO tryb 0~4,


Transfer da nych do 1.5 Gb/s.
Zgodno ze specyfikacj SATA w wersji 1.0.
10 / 100 Mb/s z automatyczn negocjacj

LAN PHY

szybkoci

Realtek RTL 8201CL PH Y

Dziaanie w trybie poowicznego / penego


dupleksu

Kodek
dwikowy

Gniazda

Zcza

Obsuga Hi gh- Definitio n Audio

ALC662

5.1 ka naowe wy jcie audio

Gniazdo PCI

x2

Gniazdo PCI Express x 16

x1

Gniazdo PCI Express x 1

x1

Zcze napdu dyskietek

x1

Kade zcze obsuguje 2 na pdy dyskietek

wbudowan Zcze Port druk arki

x1

Kade zcze obsuguje 1 Port drukarki

Zcze IDE

x2

Kade zcze obsuguje 2 urzdze nia I DE

Zcze SATA

x2

Kade zcze obsuguje 1 urzdze nie SATA

36

P4M900-M7 FE
SPEC
Zcze panela przedniego

x1

Obsuga eleme ntw pa nela przedniego

Przednie zcze a udio

x1

Obsuga funkcji audio na pa nelu przednim

Zcze wejcia CD

x1

Obsuga funkcji wejcia a udio CD

Zcze gwkowe wentylatora


procesora

Zasilanie wentylatora procesora (z funkcj


x1

Zcze gwkowe wentylatora


systemowego

x1

Smart Fan)
Zasilanie wentylatora systemowego

Zcze gwkowe kasowani a

Back Panel
I/O

Wymiary
pyty
Funkcje
specjalne

CMOS

x1

Zcze USB

x2

Zcze zasilania (24 pi nowe)

x1

Zcze zasilania (4 pinowe)

x1

Klawiatura PS/2

x1

Mysz PS/2

x1

Port szeregowy

x1

Port VGA

x1

Port LAN

x1

Port USB

x4

Gniazdo audio

x3

operacyjn
ego

przednim

190 mm (S) X 244 mm (W)

Obsuga RAID 0 / 1

Obsluga
systemu

Kade zcze obsuguje 2 porty USB na pa nelu

Biostar zastrzega sobie prawo do dawania lub


Windows 2K / XP / VISTA

odwoywania obsugi dowolnego systemu


operacyjnego bez powiadomie nia.

37

Motherboard Manual

RUSSIAN

LGA 775
CPU

Intel Core 2Duo/ Pe ntium

( 4 / Pentium D / Celero n D / Celero n

Hy per-Thre ading /
Execute Disable Bit / Enha nced I ntel

4xx 3.8

*It is recommende d to use processors Extende d Memor y 64 Technology

SpeedStep / Intel Architecture-64 /

with 95W power consumption.


FSB

533 / 800 / 1066

VIA P4M900

VIA VT8237A

Chrome9 HC 3D / 2D Graphics


256

DDR2 DIMM x 2
DDR2 533 / 667

DIMM

DDR2

256MB / 512 / 1
DIMM and ECC DIMM

/ 2 DDR2
4
ITE 8712F

Super I/O

Super I/O.

ITE "Smart Guardian"

( )

" " Ultra DMA 33 / 66 /


IDE

100 / 133

PIO 0~4,
1.5

SATA

/.

SATA

ATA

1.0.

/
High-De finition

ALC662

5.1

PCI
PCI Ex press x16

x2
x1

PCI Ex press x 1

x1

x1


IDE

38

10 / 100 /

Realtek RTL 8201CL PH Y

2

1

x1
x2

P4M900-M7 FE

SATA

x2

x1

x1

CD

x1

1
SATA



CD

x1

x1

CMOS

x1

USB-

x2

( 24 )

x1

( 4 )

x1

PS/ 2

x1

PS/2

x1

x1

VGA

x1

LAN

x1

USB-

x4

2 USB-

x3

190 ( ) X 244 ()

RAID 0 / 1


OS

Biostar
Windows 2K / XP / VISTA

OS
.

39

Motherboard Manual

ARABIC

LGA 775
Intel Core2Duo/ Pe ntium 4 / Pentium

D / C eleron D / Celer on 4xx 8.3


*It is recommended to use processors with

Hyper -Thre ading / Exec ute Disabl e


Bit / Enhance d I ntel Spee dStep /
Extende d Memor y 64 Technology

95W power co nsumption.


533 / 800 / 1066

VIA P4M900

VIA VT8237A
Chrome9 HC 3D / 2D Graphics

DDR2 DIMM

256

533 / 667 DDR2


DDR2 DIMM

DDR2

1 2 / /512 256

ECC DIMM

4
ITE 8712F
Super I/O

Super I /O .

Interface

Low Pi n Count

:


ITE ""Smart Guar dian
Ultra DMA 33 / 66 / 100 / 133

IDE

IDE

SATA

Serial ATA


PIO Mode 0~4

Realtek RTL 8201CL PH Y

ALC662

1.5 /.
1.0. SATA
100 /10 /
/

5.1

40

P4M900-M7 FE

PCI

PCI Expressx16

PCI Express x 1

IDE

IDE

SATA

SATA

CD-IN

Smart Fan

CMOS

USB

)24(

) 4(

PS/2

PS/2

VGA

USB

190 ) ( 244 X ) (

RAID 0 / 1

41

Windows 2K / XP / VISTA

USB

Biostar
.

Motherboard Manual

JAPANESE

LGA 775
Intel Core2Duo/ Pe ntium 4 / Pentium Hyper -Thre ading / Exec ute Disabl e Bit /
CPU

D / Celero n D / C eleron 4xx processor Enha nced Intel SpeedStep / I ntel


up to 3.8 GHz

Architecture-64 / Exte nde d Memory 64

*It is recommende d to use processors Technol ogy


with 95W power consumption.
FSB

533 / 800 / 1066 MHz

VIA P4M900

VIA VT8237A
Chrome9 HC 3D / 2D Graphics

256MB

DDR2 DIMM x 2

DDR2 533 / 667

DDR 2

DIMM 256/ 512MB/1GB/ 2GB

DIMMECC DIMM

DDR2
4GB

Super I/O

ITE 8712F

H/W

Super I/O

ITE

IDE

IDE

SATA

ATA

LAN PHY

Realtek RTL 8201CL PH Y

Codec

PIO Mode 0~4


1.5 Gb/
SATA1.0
10 / 100 Mb/
/

ALC662

5.1

PCI

x2

PCI Expr ess x16

x1

PCI Expr ess x 1

x1

x1

x1

42

Ultra DMA 33 / 66 / 100 / 133

P4M900-M7 FE

I/O

OS

IDE

x2

2IDE

SATA

x2

1SATA

x1

x1

CD

x1

CD

CPU

x1

CPU()

x1

CMOS

x1

USB

x2

(24)

x1

(4)

x1

PS/2

x1

PS/2

x1

x1

VGA

x1

LAN

x1

USB

x4

x3

2USB

190 mm () X 244 mm ()
RAID 0 / 1
Windows 2K / XP / VISTA

BiostarOS

2007/11/09

43

You might also like