You are on page 1of 34

2014 Feb R 3.

Site
Installation
Products

GlobalInstallationProducts
Introduction;
TheintendedreadersofthiscatalogueareProductmanagement,
Supplymanagement,Keyaccountmanagement,Designorgani-
sationandpersonalatthemarketunitswithinEricssoncompanies
andtheircustomers.
Thecatalogueshallalsobeseenasmarketmaterialtobepresen-
tedbyEricssontocustomers.
ProductsarepresentintheVariant Conguration (VC)
and in the Ericsson Conguration Portfolio (ECP).

Catalogue Index
Mechanical Support for Equipment ....................................................................................................................................................3-16
.
Cable Routing ..................................................................................................................................................................................17-25

Grounding and surge protection ......................................................................................................................................................26-34


Cables ..................................................................................................................................................................................................35

Cable Clamps..................................................................................................................................................................................36-37

Cable Sealing..................................................................................................................................................................................38-41
Cabinets and frames ........................................................................................................................................................................42-44

Tools and instruments.......................................................................................................................................................................45-54

Accessories ......................................................................................................................................................................................55-58

Power Back-up ................................................................................................................................................................................59-64

SiteinstallationproductsarealsoavailableinSiteWebShop,
where you can nd and evaluate productspresentedwithimages,
technical-andcommercialinformation.
Generalqualityanddurabilityoftheproducts;
Allproductsintheportfolioareselectedandhandpickedamong
leadingmanufacturersorspeciallyproducedwiththeaimtosecure
alonglastingdurabilityoftheinstallation,thefunctionofthenet-
workandconsequentlysavingcostfortheoperatoravoidingre-
visitstothesite.
Installationmanagement;
Thecataloguedisplaystheproductsasstandaloneunitsbutthey
areapartofanoptimisedinstallationsystemdescribedintheStand-
ard Module Overview (SMO) that should be consulted for the full
context.
Orderingmanagement;
Thecatalogueincludesavarietyoftimesavingpre-assembledkits
thatincludesallmaterialstoinstallafunctioninoneorderline.All
orderingarehandledbyEricssonusingtheproductnumbersinthe
catalogue.

Catalogue Index

MechanicalSupportforEquipment

MountingBrackets

Mounting Brackets........................................................................................................................................................... 3-14


Tubes................................................................................................................................... .............................................14
Freestanding ............................................................................................................................................................... 15, 16

Cable Runs.................................................................................................................... ............................................. 17-22

Cable Suspension Support........................................................................................................................................... 22- 24


Cable Support Kit (Hoisting Grip).................................................................................................................................... 25

Grounding Cables ...................................................................................................................................................... 26-30

Grounding Bars and Rods (combined)......................................................................................................................... 31, 32


Grounding Joint Clamps.................................................................................................................................................. 32

Grounding Cable Lugs .................................................................................................................................................... 33


Surge Protection......................................................................................................................................................... 33, 34

Surge Arrestor ................................................................................................................................................................. 34


Coaxial Cables .................................................................................................................... ............................................35

Accessories ..................................................................................................................................................................... 35

Feeder clamps................................................................................................................. ................................................ 36


......... 37
Fiber and Power Clamps.............................................................................................................................................

Hybrid Clamps................................................................................................................................................................. 37

Multi Diameter Clamp...................................................................................................................................................... 37


Cable Sealing Kits ...................................................................................................................................................... 38-41
Frames ............................................................................................................................................................................ 42
Cabinet and Frame Accessories ................................................................................................................................ 43, 44

Optical Cable Boxes........................................................................................................................................................ 44


Power Cable Boxes......................................................................................................................................................... 44

Feeder Tools ................................................................................................................................................................... 45


Electrical Power Tools..................................................................................................................................................... 46

Torque Wrenches............................................................................................................................................................ 47

Crimping tools ................................................................................................................................................................. 48


Tool Kits ..................................................................................................................................................................... 49, 50

Safety Equipment ........................................................................................................................................................ 50-52


Special Tools................................................................................................................................................................... 52

Test Instruments ............................................................................................................................................................. 53

Tools for Optical Fiber ................................................................................................................................................ 53, 54

DDF Tools ..................................................................................................................... .................................................. 54

Marking...................................................................................................................................................................... 55, 56
Miscellaneous Accessories ........................................................................................................................................ 57, 58

Battery Sets.................................................................................................................................................................... 59-61

Battery accessories ..................................................................................................................................................... 61-64

MountingBrackets
SingleRRUSupport
ThesupportkitholdsoneRadioRemoteUnitsoftypeRRUW,RRUS01orRRUS11.Thissupportcanbeinstalled
onwiderangeofverticalstructuresintelecommastandtowers.
Excellentcorrosionresistanceduetoacidproofstainlesssteelfastenersandaluminiumclamp.
CLAMPMOUNTINGRANGE:TUBES:SquareProfile:90 Angle Profile:
60 Angle Profile
Minimum:(mm)2535x3535x3540mmopening
Maximum:(mm)12090x9090x90100mmopening
Consistof:
QtyDescription
1Clampprofile,front
1Clampprofile,back
2RRUattachment
6
Nut, M10
4Washer,BRBM10
4Nutlow,M12
2Bolt,M10x200H
4Bolt,M12x35H
8Washer,BRBM12
4Locknut,LMM12
ProductNumber
SXK1072840/1

Length
290mm

Width
100mm

Height
100mm

Weight
2.106 kg

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Mounting Brackets

Double RRU Support

Single RRU with PSU Support kit

The support kit holds up to two Radio Remote Units of type RRUW, RRUS 01 or RRUS11. It can be installed on
wide range of vertical structures in telecom mast and towers. Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium clamp.

The support kit holds one Radio Remote Units of type RRUS 02, RRUS 12 or one Radio Base Station RBS 6302. It
has space for one PSU on the backside of the RRU. It can be installed on a wide range of vertical structures in telecom mast and towers. Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium
clamp.

CLAMP MOUNTING RANGE: TUBES:


Minimum: (mm)
25
Maximum: (mm)
120

Square Profile:
35 x 35
90 x 90

90 Angle Profile
35 x 35
90 x 90

60 Angle Profile
40 mm opening
100 mm opening1

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.6 m

Length
295 mm

Width
100 mm

Height
100 mm

Weight
2.86 kg

Triple RRU Support


The support kit holds up to three Radio Remote Units of type RRUW, RRUS 01 or RRUS11. It can be installed on
wide range of vertical structures in telecom mast and towers. Excellent corrosion resistance due to acid proof stainless steel fasteners and aluminium clamp.
CLAMP MOUNTING RANGE: TUBES:
Minimum: (mm)
25
Maximum: (mm)
120

Square Profile:
35 x 35
90 x 90

90 Angle Profile
35 x 35
90 x 90

60 Angle Profile
40 mm opening
100 mm opening1

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.9 m

60 Angle Profile
40 mm opening
100 mm opening

Consist of:
Qty Description
1
Clamp profile, front
1
Clamp profile, back
2
RRU attachment
1
Angle Bracket Kit
2
Angle Bracket
4
Bolt, M10x30H
4
Washer,BRB M10
2
Bolt, M10x200H
6
Nut, M10
4
Washer,BRB M10
4
Nut low, M12
4
Bolt, M12x35H
8
Washer,BRB M12
4
Lock nut,LM M12
Product Number
SXK 107 2840/2

Length
370 mm

Width
100 mm

Height
100 mm

Weight
3 kg

Double RRU with PSU Support kit


The support kit holds up to two Radio Remote Units of type RRUS 02, RRUS 12 or Radio Base Station RBS 6302.
It can be installed on a wide range of vertical structures in telecom mast and towers.
It has space for one PSUs on the backside of each RRU (max 2 PSUs). Excellent corrosion resistance due to acid
proof stainless steel fasteners and aluminium clamp.

CLAMP MOUNTING RANGE: TUBES:


Minimum: (mm)
25
Maximum: (mm)
120

Length
515 mm

Width
350 mm

Height
280 mm

Weight
11.7 kg

Square Profile:
35 x 35
90 x 90

90 Angle Profile
35 x 35
90 x 90

60 Angle Profile
40 mm opening
100 mm opening

Consist of:
Qty Description
1
Clamp profile, front
1
Clamp profile, back
4
RRU attachment
2
Angle Bracket Kit
2
Angle Bracket
4
Bolt, M10x30H
4
Washer,BRB M10
2
Bolt, M10x200H
6
Nut, M10
4
Washer,BRB M10
8
Nut low, M12
8
Bolt, M12x35H
16 Washer,BRB M12
8
Lock nut,LM M12
Product Number
SXK 107 2841/2

90 Angle Profile
35 x 35
90 x 90

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.6 m

Consist of:
Qty Description
1
RRU Triple support plate,
1
Double back profile
1
Back profile, small clamp
4
Jaw, small clamp
4
Spring
4
Locking spring
10 Nut, M12
30 Washer,BRB M12
2
Washer,BRBS M12
2
Bolt, M12x245
2
Bolt, M12x400
12 Nut low, M12
12 Lock nut,LM M12
12 Bolt, M12x35H
Product Number
SXK 107 2842/1

Square Profile:
35 x 35
90 x 90

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.6 m

Consist of:
Qty Description
1
Clamp profile, front
1
Clamp profile, back
4
RRU attachment
6
Nut, M10
4
Washer,BRB M10
8
Nut low, M12
2
Bolt, M10x200H
8
Bolt, M12x35H
16
Washer,BRB M12
8
Lock nut,LM M12
Product Number
SXK 107 2841/1

CLAMP MOUNTING RANGE: TUBES:


Minimum: (mm)
25
Maximum: (mm)
120

Length
300 mm

Width
210 mm

Height
100 mm

Weight
5 kg

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Mounting Brackets
Triple RRU Support with PSU kit

Single RRUS Support Kit With PSU/A2/TSBDA

The support kit holds up to three Radio Remote Units of type RRUS 02, RRUS 12 or Radio Base Station RBS
6302. It can be installed on a wide range of vertical structures in telecom mast and towers. It has space for one
PSUs on the backside of each RRU (max 3 PSUs. Excellent corrosion resistance due to acid proof stainless steel
fasteners and aluminium clamp.

Install one RRU or one TSBDA units perpendicular to the mounting tube with additional units such as A2 or PSU
with this kit. The RRU support can handle a wide range of all common frame leg designs, round, square, angle
etc. The grooves in the attachment beam on the back of the clamp allows the installed unit/units to always be
centered around the frame leg. All components are made of anodized aluminum and stainless steel which gives
the support excellent corrosion resistance.

Max allowed Net Wind Area (@ Windspeed 50m/s): 0.9 m


CLAMP MOUNTING RANGE: TUBES:
Minimum: (mm)
25
Maximum: (mm)
120

Square Profile:
35 x 35
90 x 90

90 Angle Profile 60 Angle Profile


35 x 35
40 mm opening
90 x 90
100 mm opening

Consist of:
Qty Description
1
RRU Triple support plate
3
Angle Bracket Kit
2
Angle Bracket
4
Bolt, M10x30H
4
Washer,BRB M10
1
Double back profile
1
Back profile, small clamp
4
Jaw, small clamp
4
Spring
4
Locking spring
10 Nut, M12
30 Washer, BRB M12
2
Washer, BRBS M12
2
Bolt, M12x245
2
Bolt, M12x400
12
Nut low, M12
12
Lock nut, LM M12
12
Bolt, M12x35H
Product Number
SXK 107 2842/2

Clamp mounting range:


Frame leg/form
Min (mm)
Tubes Diameter
25
Square profile
35x35
90 Deg. Angle
35x35
60 Deg Angle(opening) 40

Max (mm) (with 200mm bolts)


120
90x90
90x90
100

Consist of:
Qty Description
2
Clamp profile front
2
Clamp profile,Back
2
Attachment beam
2
Support arm
1
Attachment angle
1
Attachment arm
2
Countersuncscrew , M8x30
12 Nut, M10
12 Washer M10
4
Lock nut M10
4
Bolt, M10x130H
8
Bolt, M10x30H
Length
515 mm

Width
350 mm

Height
280 mm

Weight
14.1 kg

RRU Wall Support


A light weighted support for installation of one RRU or one RBS 6302 towards the wall.
The support can fit all common Ericsson RRU models such as RRUW,RRUS 01, RRUS 11, RRUS 02 and RRUS
12.
It is also possible to attach a PSU or an A2 on the backside of the RRU.
All components are made of anodized aluminum and stainless steel which gives the support excellent corrosion
resistance.
Max allowed antenna net wind area at wind speed:
150 km/h (42m/s): 1.4 m
200 km/h (55m/s): 0.8 m
Consist of:
Qty Description
2
RRU Wall bracket
2
Attachment arm 360
4
Bolt, M10x30H
4
Washer M10
4
Bolt, M8x35H
4
Lock nut M8
8
Washer M8
Product Number
SXK 107 2848/1

Max net wind Area at 180 Km/h (50m/s): 0,6 m2

Length
370 mm

Width
80 mm

Height
80 mm

Weight
2.5 kg

Product Number
SXK 107 2839/1

Length
530 mm

Width
95 mm

Height
85 mm

Weight
5 kg

Expansion Kit For Dual RRUS support


Install two RRU or TSBDA units perpendicular to the mounting tube with additional units such as A2 or PSU. The
RRU support can handle a wide range of all common frame leg designs, round, square, angle etc. The grooves in
the attachment beam on the back of the clamp allows the installed unit/units to
always be centered around the frame leg. All components are made of anodized aluminum and stainless steel
which gives the support excellent corrosion resistance. Max net wind Area at 180 Km/h (50m/s): 0,6 m
Clamp mounting range:
Frame leg/form
Tubes Diameter
Square profile
90 Deg. Angle
60 Deg Angle(opening)

Min (mm)
25
35x35
35x35
40

Max (mm) (with 200mm bolts)


120
90x90
90x90
100

Consist of:
Qty Description
2
Support arm
1
Attachment angle
1
Attachment arm
2
Countersuncscrew , M8x30
4
Lock nut M10
8
Washer M10
8
Bolt, M10x30H
Product Number
SXK 107 2839/2

Length
370 mm

Width
80 mm

Height
80 mm

Weight
2 kg

Angle Bracket for RRUS


With this Angle bracket it is posible to attach one PSU on the backside of RRUS 01, RRUS 02, RRUS 11 or RRUS
12.
Consist of:
Qty Description
2
Angle Bracket
4
M10 Washer
4
M10x30Bolt
Product Number
NTM 201 4128/1

Length
190 mm

Width
90 mm

Height
60 mm

Weight
0.865 kg

Mechanical Support for Equipment

Mechanical Support for Equipment

MountingB rackets

Mounting Brackets

Single RRU Support

Link Support, 1-Leg

The single RRU support is designed to carry a single RRU attached to a structural leg memeber.

Clamp kit in two levels, with space for one mounting tube (mounting tube not included in the kit).
Typical for installation of large (diam. 2,6m) radio links, or several small ones or other common
telecom equipment.The 1-leg link support can be installed on mast leg (min.25-max.270mm) as well as
conical towers (min.60x60mm, max. 200x200mm).

The support can be used on a range of pole diameters and with or without a PSU attached to the backside of the
RRU. It can also be mounted on angle irons as well as box sectional beams
Consist of:
Qty Description
2 Single RRU clamp
2 RRU clamp
4 Bolt M10, A4
4 Threaded rod M10, HDG
16 Washer BRB, HDG
20 Nut M10, HDG
RANGE Tubes SquareProfile 90 angle 60 angle
CLAMP
MOUNTING

Minimum: [mm]
25 35x35 35x35 40
mm width of opening.
Maximum:[mm]
114 80x80 80x80 100

mm width of opening.
Clamp profiles S355MC FZV
Nuts and bolts 8.8 FZV or equivalent
Product Number
SXK 107 2869/1

Length
250 mm

Width
130 mm

Height
Weight
70 mm 4,3kg

Cable Ladder RRU Support


The RRU support is designed for attaching RRU s to existing cable ladders.
The support is delivered as a flat pack and can easily be mounted on cable trays of width 300-500mm
Consist of:
Qty Description
1 RRU cable tray holder sheet L
1 RRU cable tray holder sheet R
8 Self tapping screw

Hole pattern

Product Number
SXK 107 2867/1

Product Number
SXK 107 2832/1

Length
400 mm

Width
320 mm

Height
230 mm

Weight
23 kg

Wall Support, Light


Wall support kit in two levels with space for one mounting tube (mounting tube not included in the kit).
Typical for installation of panel antennas, radio links or other common telecom equipment. The Light wall support
can handle mounting tubes 65mm-90mm.

MECHANICAL SPECIFICATION
DIMENSIONS
Length (mm)
325
Width (mm)
300-500
Height (mm)
288
Slope ( )
17,5
MATERIAL
Steel plates
Bolts and nuts

Consist of:
Qty Description
1 Clamp
1 Clamp double back profile
4 Bolt M12x400
8 Jaw, small clamp
4 Washer BRB M12
2 Backprofile, small clamp
4 Double back profile
2 Double back profile
8 Locking spring
8 Spring
8 Spring
12 Nut, M12
12 Nut M12
4 Large washer, BRBS M12
4 Large washer BRBS M12
8 Locking spring
8 Jaw, large clamp
4 Bolt, M12x245
2 Upper plate 100x10x225
4 Washer BRB M12
2 Lower plate 80x10x175
16 Washer BRB M12
16 Nut, M12
8 Bolt, M12x425

Consist of:
Qty Description
2 Holder part
2 Tube clamp part
8 Washer BRB M12
2 U-bolt, 60mm-90mm
4 Lock nut, LM M12
8 Nut M12
4 Bolt M12x40H

S355MC FZV
A4-70 or equivalent
Length
Width
450 mm 350 mm

Height
10 mm

Weight
3 kg

Product Number
SXK 107 2833/1

Length
285 mm

Width
190 mm

Height
150 mm

Weight
4.5 kg

Universal Antenna Support


Universal clamp kit in two levels with space for one mounting tube(the upper clamp can be adjusted to tilt the antenna inclination). Typical for installation of panel antennas, radio links or other common telecom equipment such
as main remote units, power units, TMA, filters etc. Clamp mounting range: Tubes, min.diam.25mm- max 210mm
diam. Tower legs square profiles: Min.25x25mm-Max.150x150mm.
Angle profile: Min.35x35mm-Max.150x150mm. (Mounting tube not included).
Consist of:
Qty Description
2 Holder part
28 Nut, M12
2 Counter support part
4 Threaded rod HGS, M12
2 Tube clamp part
6 Lock nut, LM, M12
2 Tilt arm part
6 Bolt, M12x40H
20 Washer BRB M12
2 U-bolt, diam.60mm-diam.90mm
Product Number
SXK 107 2126/1

Length
290 mm

Width
190 mm

Height
150 mm

Weight
8 kg

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Mounting Brackets

Parallel Bracket Kit

Top Spire Support

Bracket extension kit for two levels.Typical for extension of existing mounting tubes or as a support for panel antennas, small radio links or other common telecom equipment. The bracket can handle mounting tubes and frame
legs 60mm-90mm. Note: mounting tube not included.

An extension kit for towers and masts with space for three mounting tubes. Typical for installations of panel antennas up to 2,3m. Clamp mounting range for tubes 25mm-120mm, for square profiles 30x30mm- 90x90mm

Consist of:
Qty Description
16 Nut M12
8
Washer BRB M12
4
U-Bolt, 60mm-90mm
2
Z profile
8
Lock nut, LM M12
Product Number
SXK 107 2834/1

Length
250 mm

Width
130 mm

Height
110 mm

Weight
2.5 kg

Double Antenna Support


Clamp kit in two levels, with horizontal beams and space for two mounting tubes (mounting tubes not included in
the kit). Typical for installation of panel antennas, radio links or other common telecom equipment. Clamp mounting range: Tubes; Min.25mm-Max.120mm, squaare profiles; Min.30x30mm-Max.90x90mm.
Consist of:
Qty Description
1
Cue Dee clamp
4
Bolt M12x245, A4
8
Jaw, small clamp
4
Washer BRB M12, A4
4
Backprofile, small clamp
2
Z-profile
8
Spring
4
U-bolt, 60mm-90mm
12 Nut M12, A4
8
Washer BRB M12, A4
4
Large washer BRBS M12, A4
16 Nut M12, A4
8
Locking spring
8
Lock nut LM M12, A4
Product Number
SXK 107 2835/1

Length
790 mm

Product Number
SXK 107 2837/1

Width
500 mm

Height
300 mm

Weight
45 kg

The dual panel antenna frame can be mounted on pole, wall or tower leg. Can be mounted on poles diam. 50mm,
80mm or 210mm or angle iron 50x50mm, 110x110mm or 150x150mm. It is adjustable +- 45 degres in horizontal
direction. If mounted according to the installation instruction it withstands wind speed up to 30m/s.

Width
130 mm

Height
90 mm

Weight
11.5 kg

Antenna support kit for two levels with space for 3 mounting tubes on one centre tube. Typical for installations of
panel antennas. (Centre tube and mounting tubes not included). Triple antenna support can handle centre tube
75mm-120mm and mounting tube 45mm-60mm.
Consist of:
Qty Description
6
U-bolt, 45mm-60mm
24 Washer BRB M10, A4
48 Nut M10, A4
6
Bracket
6
Threaded rod HGS M10x120, A4
4
Distance 18mm, L=42mm
Length
285 mm

Length
300 mm

Wall Mount, MHGA

Triple Antenna Support

Product Number
SXK 107 2836/1

Consist of:
Qty Description
1
Tube, diam.114mm, t=5, L=3000mm
8
Jaw, small clamp
3
Tube, diam.60mm, t=3, L=2500mm
4
Backprifile, small clamp
1,5 Tripple antenna support (set)
8
Spring
9
U-bolt, 45mm-60mm
12 Nut, M12, A4
36 Washer BRB M10, A4
4
Large washer BRBS, M12. A4
72 Nut, M10, A4
8
Locking spring
9
Bracket
4
Bolt, M12x245, A4
9
Threaded rod HGS M10x120, A4
4
Washer BRB, M12, A4
6
Distance, diam.18mm, L=42mm 6
42 Threaded rod, HGS, M12x500, A4
2
Cue Dee clamp, back to back
1
Distance

Consist of:
Qty Description
2
Mounting frame, upper and lower
1
Splitter bracket kit
1
Joint
2
Splitter, dual-panel
1
Bolt kit for joint
1
Cable kit, dual-panel
1
Tower clamp, upper
2
Antenna, low-band or high-b.
1
Tower clamp, lower
2
Antenna mounting kit
2
Counter block
1
Spacing plate, high-b.antennas
1
Pin bolt kit for tower clamps
1
Spare bolts
1
Cable clamp kit
Product Number
SXK 118 0932/1

Width
190 mm

Height
150 mm

Weight
2.6 kg

Length
3100 mm

Width
260 mm

Height
200 mm

Weight
40 kg

Extension Kit MHGA


Extension kit to Wall mount MHGA (SXK 118 0932/1), 2SP Antenna mounting frame.
Consist of:
Qty Description
2
Aluminium profile, L=2400mm
4
Screw bolt, M12x120
8
Washer Rb 13
4
Locking nut, M12
1
Tube of Gleitmo
40 Feeder clamp
4
Screw bolt, M8x100
4
Screw bolt, M8x70
8
Locking nut, M8
8
Washer, Rb 8,4
4
Screw bolt, M8x25
4
Locking nut, M8
4
Washer, Rb 8,4
Product Number
SXK 118 0933/1

10

Length
2400 mm

Width
105 mm

Height
130 mm

Weight
16 kg

11

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Mounting Brackets

AIR Support

Pole Mount Rear RBS/BBS 6301

The AIR support secures one AIR unit (Antenna Integrated Radio) or one panel antenna direct towards the tower
leg of a telecom Mast/Tower. Mount it towards straight/inclined tower leg with the forms: round, square, profilewith 90 degree angle and profile with 60 degree angle.

Support for RBS/BBS 6301 with mast attachment and protection cover for the rear. Included screw and fasteners
for wall mount. Supplied in an transport optimized package.

Max Azimuth adjustment: +/- 60 degree [Totally 120 degree].


Max inclination of tower leg: 4 Degree.
Max mechanical tilt: 4 Degree. Max wind area (at 50m/s): 1,5m.
Mounting range of AIR support.
Minimum: [mm]
Maximum:[mm]

Tubes
25
120

Square
35x35
90x90

Profile angle 90
35x35
90x90

Profile angle 60.


40 mm width of opening.
100 mm width of opening.

Length
285 mm

Width
190 mm

Height
150 mm

Weight
8 kg

The Flexible ALD Mounting support fasten 1, 2 or 3 units of ALD:s (such as TMA/filters) to a Telecom Tower or
Mast. With the "Extension ALD support" it is possible to mount up to three extra ALD units on the Flexible ALD
Mounting Support. The Flexible ALD Mounting Support can be mounted towards Mast/tower leg with the forms:
round, square, profile with 90 degree angle and profile with 60 degree angle.
Max Wind Area (at 50 m/s): 0.5m.
Mounting range of the Flexible ALD Support.
Tubes
Square
Profile angle 90
Minimum: [mm]
25
35x35
35x35
Maximum:[mm]
120
90x90
90x90

Profile angle 60.


40 mm width of opening.
100 mm width of opening.

Number of required supports for the installation


SXK1072854/1
SXK1072854/2
Number of ALD
Flexible ALD Support
Extension ALD Support
1, 2 or 3 ALD:s
1 Pcs
0 Pcs
4 Pcs ALD:s
1 Pcs
1 Pcs
5 Pcs ALD:s
1 Pcs
2 Pcs
6 Pcs ALD:s
1 Pcs
3 Pcs

Width
600 mm

Height
650 mm

Weight
33.48 kg

Width
135 mm

Consist of:
Qty Description
1
Installation frame side
2
Mast attachment
1
Protection cover side
Product Number
NTM 201 4044/1

Length
800 mm

Width
600 mm

Height
650 mm

Weight
35.5 kg

Wall Mount Rear RBS 6301


Wall Support for RBS 6301 with protection cover for the rear and air spacer. Included screw and fasteners for wall
mount. Supplied in an transport optimized package.
Consist of:
Qty Description
1 Installation frame rear
1 Protection cover rear
1 Air spacer
Product Number
NTM 201 4045/1

Length
1200 mm

Width
800 mm

Height
450 mm

Weight
36 kg

Omni Antenna Support


This flexible tiltable support secures one omni directional antenna in the indoor ceiling (inbuilding). The antenna is
mounted with a minimum distance (from ceiling) of 108 mm. With the supplied extension the antenna can be
mounted 302 - 402 mm from the ceiling. This extension is usefull when large metalic objects such as girders, ventilation shafts blocks the broadcast.

Consist of:
Qty Description
1
ALD Support, Clamp profile Aluminium
3
Mounting Tube =60x3mm, L=400mm, Aluminium
1
Fastener set, Acid Proof Stainless Steel
Length
410 mm

Length
800 mm

Support for RBS/BBS 6301 with mast attachment and protection cover for the side. Included screw and fasteners
for wall mount. Supplied in an transport optimized package.

Flexible ALD Mounting Support

Product Number
SXK 107 2854/1

Product Number
NTM 201 4043/1

Pole Mount Side, RBS/BBS 6301

Consist of:
Qty Description
1
Clamp Profile set, Aluminium
1
Rotate Plate, Acid proof Steel
1
Fastener set, Acid proof Steel
Product Number
SXK 107 2849/1

Consist of:
Qty Description
1
Installation frame rear
2
Mast attachment
1
Protection cover rear

Height
135 mm

Weight
4.8 kg

Extension ALD Mounting Support


Extension ALD mounting support is used together with the Flexible ALD Mounting Support to increse the number
of ALDs to a maximum of 6 ALDs. Compliance to ROHS 2 directives 2011/65/EU.
Number of required supports for the installation.
SXK1072854/1
SXK1072854/2
Number of ALD
Flexible ALD
Extension ALD Support
1, 2 or 3 ALD:s
1 Pcs
0 Pcs
4 Pcs ALD:s
1 Pcs
1 Pcs
5 Pcs ALD:s
1 Pcs
2 Pcs
6 Pcs ALD:s
1 Pcs
3 Pcs

Max antenna weight: 1.0 Kg


Maximum Tilt: 15 degree
Rotation: 360 degree
Consist of:
Qty Description
1
Adjustable bracket
1
Extension 302-402
1
Screw/Plug kit
1
Allen Key
Product Number
SXK 107 2845/1

Length
130 mm

Width
130 mm

Height
12 mm

Weight
1.6 kg

Consist of:
Qty Description
1
Tube holder
1
Mounting tube
Product Number
SXK 107 2854/2

12

Length
550 mm

Width
100 mm

Height
85 mm

Weight
1.1 kg

13

Mechanical Support for Equipment

Mechanical Support for Equipment

Mounting Brackets

Freestanding

Parallel Cog Support

Guyed Roof Top Kit, 3.0 m

The Parallel cog support is designed for installation of panel antennas, small radio links, TMA or RRU.
It has 205-300 mm offset between antenna tube and Tower/Mast strutting/profile. Tube is not included in kit.

The Guyed roof top kit is designed to meet the demands of a sturdy antenna mount for directional antennas and
parabolas. Mount it on a roof top site where drilling through in the roof is not allowed. The construction is balanced with concrete blocks (500x500x50 mm). The blocks are not supplied in the kit.

The support kit has a wide clamping range and fits


Tubes with diameter 25-120 mm
Rectangular profiles: 35x35mm to 90x90 mm
90Angle profiles: 35x35mm to 85x85 mm
60Angle profiles: opening 45 mm to 100 mm
Consist of:
Qty Description
2
Parallel bracket C-C 134
2
Parallel bracket C-C 104
2
Clamp profile back
2
U-bolt
12 Washer M12
20 Nut M12
4
Bolt M12x35
8
Washer large M12
4
Lock nut M12
Product Number
SXK 107 2843/1

Length
285 mm

Width
190 mm

Height
150 mm

Weight
6 kg

Consist of:
Qty Description
1
Rubber carpet 1
16 Locking nut
1
Cross
4
Angle
1
Angle
4
Threaded rod
48 Washer
4
Mount f. Strut
50 Nut
12 Screw
4
Bottom plate
4
Screw
8
Screw
2
Clamp w. Ear
1
Foot
1
Tube 1
2
Screw
Product Number
NTM 201 3164/1

Offset Support Kit

Length
1200 mm

The Offset support kit allows one RRU to be mounted behind a panel antenna without any extra equipment. The
offset bracket can be mounted against tower and mast leg sections with diameters = 25 - 76.1 mm. It fits
against both tilt brackets and directly against the antenna. Max Net Wind Area* (at windspeed 50m/s): 1.2 m.
*Offset bracket kit installed with a panel antenna.

Roof Tube Single-based

Consist of:
Qty Description
2
Offset bracket
2
Clamp
2
U-bolt, M12
12 Nut/Washers

Height mounted: 2000 mm


Foot print: = 600 mm, 0.3 m
Pole diameter: = 60 mm.

Product Number
SXK 107 2844/1

Length
250 mm

Width
150 mm

Height
100 mm

Weight
4 kg

Tubes
Antenna Tube
These Aluminium tubes supports panel antennas, radio links, RRU and other telecom equipment. Choose between outer diameter =60, 75, 90 or 114 mm. Choose between tube length 1.0 m, 1.5m 1.6m, 2.5 m 2.9 m and
4.0 m.

Width
800 mm

Height
340 mm

Weight
80.5 kg

Self-supporting roof single-based system is design for small directional antennas, RRU:s and small parabolic dish.
The non-penetrating mount is easy and fast to assemble.

Consist of:
Qty Description
1
Bottom plate
1
Upper plate
1
Rubber duct
1
Tube
3
Counter weight
3
Threaded rod
11 Nut, M6M
9
Washer, BRB
2
Screw, M6S
Product Number
NTM 201 1205/1

Length
625.2 mm

Width
625.6 mm

Height
410.6 mm

Weight
91.1 kg

Consist of:
Qty
Description
1
Aluminium tube
Product Number
SXA 120 729/16
SXA 120 215/29
SXA 120 216/40
SXA 120 747/1
SXA 120 748/1
SXA 120 752/1

14

Length
1600 mm
2900 mm
4000 mm
1000 mm
2500 mm
1500 mm

Width
60 mm
75 mm
90 mm
75 mm
60 mm
114 mm

Height
60 mm
75 mm
90 mm
75 mm
60 mm
114 mm

Weight
2.3 kg
6.15 kg
14.4 kg
2.12 kg
2.32 kg
3.63 kg

15

Mechanical Support for Equipment

Cable Routing

Freestanding

Cable Runs
Free-standing Ballast kit 2m

Greenfield Site Tower kit

Free-standing non penetrating rooftop.Typical for installation of panel antennas, radio links or other common telecom equipment.(Ballast not included)

This kit is designed for a Greenfield Tower site. It is a complete solution of installation material for the outdoor site.
The cable runs, grounding wire, grounding rods, grounding bar and installation instructions are delivered in a
transport optimized export package.

Consist of:
Qty Description
4
Ballast box
3
Nut, M20 HTG
1
Upper tie bar fitting
1
Lock nut, M12, A4
1
EPDM rubber, 1050mmx1050mm
6
Washer, M20 HTG
1
Tube, diam.75mm, L=2000mm
2
Washer, M12, A4
1
Supporting tube, diam.60mm, L=1500mm
2
Bolt, M20x55H HTG
4
Distance, supporting tube diam.60mm
1
Bolt, M20x50 HTG
1
Plate, supporting tube diam.60mm
1
Pipe attachment
1
Support tube diam. 60mm
1
Corner attachment
8
Washer BRB, M8, A4
10 Bolt, M20x55H HTG
4
Lock nut, M8, A4
10 Nut, M20, HTG
4
Bolt, M8x75mm, A4
2
Lock nut, M12, A4
1
Plate, supporting tube 60mm
2
Lock nut, M8, A4
4
Washer BRB, M8, A4
2
Bolt, M12x45H, A4
4
Washer BRB, M12, A4
2
Bolt, M8x70, A4
4
Corner attachment1Washer, M20 HTG
1
Bolt M12x160, A4
2
Distance, diam.24mm, L=20mm
Product Number
NTM 201 3862/1

Length
2000 mm

Consist of:
Qty Description
1
Cable ladder kit. 2x2.25m AluZinc
1
Basic wire kit, 70m, 35mm
1
Cable ladder cover kit, 2x1.125m, AluZinc
1
Rod kit, 3m
1
Wire kit, 40m 35mm
1
Installation instruction
1
Outdoor ground bar
1
Standard site material description
Product Number
NTM 201 3501/1

Width
480 mm

Height
540 mm

A high quality outdoor cable run for the Telecom application. Carries feeder cable , RRU cable , power cable, fiber
and grounding cable. Modular cable carrying system for mount outdoors at rooftops, walls or between telecom
masts/towers/antennas and shelters/flatpacks/RBS cabinets. Possible to mount free standing or supported.
Heavy duty steel cable run of high quality with self-healing AluZinc coating. Long service life in corrosive environments.
Easy assembly
Mechanic system with package optimized for elevators/containers.
Slim design easy to handle.
Quick installation with universal joints and standard tools only.
No sharp edges.

Width
650 mm

Height
150 mm

Weight
111 kg

Consist of:
Qty Description
2
Cable ladder 2.25m (W=400mm) AluZinc
1
Installation bolt set (25pcs)
2
Universal ladder fixture
4
Joint
6
Angle bracket
1
Screw set with plugs
2
End stop

The Free Standing Roof Tube is designed for non penetration installations on flat roofs of RRUs and antennas.
The support fits tube with diameter 60 mm. It has adjustable tilt up to 8. Ballast up the support with four concrete
slabs of thickness 40-65 mm (not included).

Product Number
NTM 201 3138/1

Concrete slab (mm)


350x350x50
400x400x40
500x500x50

Cable Ladder cover kit, 2x1.125 m, AluZinc coated

Footprint (mm)
800x800
900x900
1100x1100

Length
300 mm

Length
2250 mm

Width
4150 mm

Height
80 mm

Weight
22 kg

The cover set protects the cable run between the mast and the base station. It avoids falling ice, smaller stones as
well as sunlight damaging the feeder cables.

Consist of:
Qty Description
2
Bracket, Galvanized Steel
4
Roof Protection, Rubber 80x600
1
Nut/washer set, Stainless Steel
Product Number
SXK 107 2855/1

Weight
95.23 kg

Cable Ladder Kit, AluZinc coated

Free-standing Roof Tube

16

Length
2310 mm

Consist of:
Qty Description
2
Protection cover (W=400mm)
1
Bolt set 14 pcs
Width
300 mm

Height
200 mm

Weight
6.7 kg

Product Number
NTM 201 3159/1

Length
1130 mm

Width
390 mm

Height
245 mm

Weight
16.6 kg

17

Cable Routing

Cable Routing

Cable Runs

Cable Runs
These kit is designed for a RBS room. Basic Indoor Kits is a complete solution of installation material for the indoor site and can be
ordered in two sizes. Cable ladders and profiles, grounding system, marking and sealing material are delivered in a transport optimized
export package.

Cable Runs
Basic Ladder kit Large
Consist of:
Qty Description
3
Cable ladderkit, Grey, 2x2,25m (W=300mm)
4
Cable kit 2m, 35mm, Yellow/Green
2
Cable tray, Grey, 2x0,6m, (W=150mm)
1
Common installation material
1
Cable sealing kit for 1/4"-7/8" cable
1
Site material description
1
Cable kit 25m, 35 mm Yellow/Green
3
Indoor cable trunk, 2x2m
Product Number
NTM 201 3416/3

Length
2300 mm

Width
470 mm

Height
500 mm

Weight
80.25 kg

Consist of:
Qty Description
2
Cable ladder kit, Grey, 2x2.25m (W=300mm)
3
Cable kit 2m, 35mm, Yellow/Green
2
Cable profile, Grey, 2x0.6m
1
Common installation material
1
Cable sealing kit, for 1/4" - 7/8" cable
1
Site material description
1
Grounding cable17m, 35mm, Yellow/Green
2
Indoor cable trunk 2x2m
Length
2300 mm

Width
470 mm

Height
500 mm

Weight
57.15 kg

Consist of:
Qty Description
2
Cable profile kit, 2x2m
1
Grounding cable kit,12m
1
Common installation kit
1
Cable sealing kit, IP54

Width
425 mm

Height
140 mm

Weight
21.5 kg

Consist of:
Qty Description
6
Mesh tray,L= 2500mm W=75 mm,Pre-galvanized
10
Joint for mesh tray
10
Universal bracket
6
Divider plate, 25 mm L=2750 mm
20
Wall bracket
20
Fastening clamp
50
Installation bolt/nut
1
Equipped bond bolt
Product Number
NTM 201 4151/1

Length
2550 mm

Width
85 mm

Height
70 mm

Weight
20.9 kg

Cable Tray kit 2x2 m, Paint Coated, Grey


Length
2500 mm

Width
255 mm

Height
320 mm

Weight
38.6 kg

Cable Ladder kit, Paint Coated 300 mm


Consist of:
Qty Description
2
Cable ladder, Length 2250mm Width 300mm
3
Supporting Iron
4
Joint
3
T-bolt M10x35
4
Universal ladder fixture
3
Pendant bracket
6
Angle bracket
1
Bolt set M8x16 25-pack
1
Pendant rail 2250mm
2
Grounding screw =9mm, 35mm
2
Ceiling fixing
8
Screw set with plugs 5-pack M8x65 mm
3
Cantilever arm
Length
2260 mm

Width
325 mm

The cable try carries and covers cable inside a RBS-room or RBS-shelter. widht=0,1 m.
Consist of:
Qty Description
2
Cable ladder profile, 2000x100mm
2
Cable ladder profile cover, 2000x100mm
2
Profile End Piecs
40 Assembly Screw, B8
Product Number
SXK 107 2023/1

Length
2010 mm

Width
110 mm

Height
70 mm

Weight
9.1 kg

Cable Tray Fitting Profile


Cable Tray 50 mm wide for close installation environment. Can be mounted vertical or horizontal. Cables/fiber/jumper cable are fixed by tie straps in the mushroom-shaped" hole. Supplied with screw for wall mount and potential equalization bolt. High quality pre-galvanized and paint coated.

Height
85 mm

Weight
18.5 kg

Consist of:
Qty Description
2
Cable tray, W=50 mm L=2000 mm
8
Screw TRX 4,5x50 mm
8
Plastic plug 6x42 mm
1
Mounting instruction
2
Equipotential bond bolt
Product Number
NTM 201 4152/1

18

Length
2250 mm

Cable Mesh tray for the indoor Telecom application 6x2500 mm x 75 mm. Carries feeder cable, power cable, fiber
cable as well as grounding cables. Suitable in indoors environment. Supplied with mounting accessories for wall
mounting and mounting on existing cable ladder with a fastening clamp. Electrical continuity across joint according to SS-EN 61537:2001.

It can be mounted in container as well as RBS room and is supplied with cable inlet, grounding material, mounting
profiles and fastening material.

Product Number
NTM 201 3160/2

Consist of:
Qty Description
2
Cable ladder, Length 2250mm Width 400mm
3
Supporting Iron
4
Joint
3
T-bolt M10x35
4
Universal ladder fixture
3
Pendant bracket
6
Angle bracket
1
Bolt set M8x16 25-pack
2
Pendant rail 2250mm
2
Grounding screw =9mm, 35mm
2
Ceiling fixing
3
Screw set with plugs 5-pack M8x65 mm
3
Cantilever arm
1
L-T-X branch

Mesh Tray Set

Indoor Installation Kit, light

Product Number
NTM 201 3885/1

This indoor cable run is designed for mount in ceiling or on wall. The length, 2.25 meter, renders possible usage in
buildings with narrow entrance, e.g. elevators. To obtain desired length of cable ladder: use several NTM 201
3745/1.

Product Number
NTM 201 3745/1

Basic Ladder kit Medium

Product Number
NTM 201 3416/2

Cable Ladder Kit, Paint Coated 400 mm

Length
2050 mm

Width
65 mm

Height
30 mm

Weight
2.8 kg

19

Cable Routing

Cable Routing

Cable Runs

Cable Runs
Cable Tray, 2x0.6 m, Paint coated, Grey

Outdoor Cable Tube kit

This product is mounted on the wall and used to lead cables down from the cable run to the RBS cabinet,width
=0,15m.

Fastening material for tower/mast mounting and wall mounting included.

Consist of:
Qty Description
2
Fitting profile, 600x150x14 mm
2
Screw and plug set, 4,5x50 mm 4-pack
4
Grounding screw, M6x12mm, = 9mm
Product Number
SXK 107 2158/2

Length
620 mm

Width
160 mm

Height
25 mm

Weight
2.2 kg

Cable Tray, 2x2 m, Paint coated, Grey


The Cable Tray kit is a complement to the traditional Cable Ladder kit and is suitable for cable runs in close installation environment. It can be mounted on to vertical walls as well as on to horizontal ceiling. Cables are fixed to
the Cable Tray with traditional tie straps. Widht=0,2m.

Length
2020 mm

Width
210 mm

Height
25 mm

Weight
8.5 kg

Consist of:
Qty Description
1
2.5m Clamping Band
Width
30 mm

Height
3 mm

Weight
1.71 kg

Max Clamping
5 mm

Indoor Cable Tray


The cable trunk is used indoor for protection of cables and fiber against exterior mechanical influences. Wall
mounting or cable ladder mounting.
Consist of:
Qty Description
1
Screw,nut and washer kit
2
Cable trunk, 40x25mm L=2m
10 Screw 4,2x25mm, TGS-C3
10 Plastic wall plug, Red
Product Number
NTM 201 3730/1

Length
2100 mm

Width
200 mm

Height
200 mm

Weight
1.1 kg

Mini Tray On Roll


White Mini Installation tray on 20 m roll made of silicone and cadmium-free PVC. Perfect for your indoor installation of RRU cabel/fiber or grounding cable. Backside with strong double-stick adhesive tape and perforated holes.
Frontside with Self-locking lid. Supplied in a 20 meter roll with transport handle, instruction and bevel scale.
Consist of:
Qty Description
1
Mini tray 30x30mm x 20m
Product Number
MPB 901 026/1

Length
390 mm

Width
390 mm

Height
125 mm

Weight
5.14 kg

Tray W/H/L
30 mm/30 mm/20 m

The flexible tube kit is used for protection of cables indoor against exterior mechanical influences.
Consist of:
Qty Description
2
Flexible Tube 25mm, l=3m
15 Tube holder
5
Jointing sleeve
3
Conduit elbow

20

Height
300 mm

Weight
3.5 kg

Length
2200 mm

Width
90 mm

Height
90 mm

Weight
2 kg

Outdoor Slitted Conduit kit 48mm


The tube kit is used for protection of cables and fiber against exterior mechanical influences.The tube
is openable for easy installation of preassembled cables.Each tube is 2.1m long and innerdiameter
is 44.0mm, enough to fit three OIL cables and three power cables.
Consist of:
Qty Description
5
Conduit 48mm, L=2100mm
Product Number
NTM 201 3929/2

Length
2200 mm

Width
160 mm

Height
130 mm

Weight
3.5 kg

Flexible Conduit kit 25m


The flexible conduit kit is used for protection of cables against external mechanical influences. Inner diameter
40mm and it fits at least three OIL (optical)cables and three power cables for Main-Remote roof-top sites or or to
be used in tower and mast.The flexible tube is 25m long. The kit also includes T-branches, fastener and pull wire
for fast and easy installation.
Consist of:
Qty Description
25 Flexible conduit 50/40mm, including pullwire
5
Straight coupler for flex.conduit 50mm
2
T-branch for flex. conduit
1
Conduit clip, pack of 50
1
Mounting screw 25x4,2mm, pack of 100
1
Plastic plug, Red, 35x6mm, pack of 100
30 Tie strap, stainless steel plastic coated, 457x9,5
2
Electrical tape, Black
Product Number
NTM 201 3811/1

Length
950 mm

Width
900 mm

Height
250 mm

Weight
11 kg

Overlength Box Kit

Tube kit, 2x3 m indoor

Product Number
NTM 201 218/3

Width
300 mm

Outdoor Slitted Conduit kit 27mm

Product Number
NTM 201 3929/1

Clamping band that secures cable against the wall. Opening gap between wall and the clamping band is 5 mm.
Hot-dip galvanized.

Length
2500 mm

Length
1800 mm

Consist of:
Qty Description
5
Conduit 27mm, L=2100mm

Clamping Band

Product Number
SXA 120 1869/1

Product Number
NTM 201 3727/1

The tube kit is used for protection of cables and fiber against exterior mechanical influences.The tube is openable
for easy installation of preassembled cables.Each tube is 2,1m long and inner diameter is 23.5mm, enough to fit
one OIL cable and one power cable.

Consist of:
Qty Description
2
Fitting profile, 2000x200x14mm
2
Screw and plug set, 4,5x50 4-pack
4
Grounding Screw, M6x12mm, =9mm
Product Number
SXK 107 761/2

Consist of:
Qty Description
5
Cable conduit slitted
5
Straight coupler slitted
15 Tie strap, 457X9,5mm
1
Electrical tape, Black 20MX19MM
1
Electrical tape, Black 20MX50MM
30 Mounting screw
30 Plastic plug, Red
15 Conduit clamp

Length
330 mm

Width
330 mm

Height
110 mm

Weight
1.13 kg

The box holds up to 30 m OIL cable excess length. It is easy to mount to a wall, tower leg etc and possible to
stack on to each other.
Consist of:
Qty Consist
1
Box
1
Box cover
2
Cable Tie 457X9,5
1
Cable Tie Velcro tape
2
Bracket
4
Mounting bolt
4
Locknut
6
Cover bolt
4
Wall plugg TP2 red
4
Wall screw TGS-C3 4,2X25
4
Wall washer 4,3X8
Product Number
NTM 201 3729/1

Length
280 mm

Width
440 mm

Height
42 mm

Weight
1.1 kg

21

Cable Routing

Cable Routing

Cable Runs

Cable Suspension Support


Basic Cable Duct kit, 12 m

Wire Suspension Kit 50m

This cable duct kit made of recycled rubber can carry up to 4 pcs of 7/8" feeder cable and 2 pcs of grounding
wire. The installation of the ducts does not require any mechanical fixing to flat roofs. The duct is simply laid on
the roof and is connected to the next one with the supplied jointing tube. This way you rapidly create a feeder
cable infrastructure without penetrating the roof surface. With the supplied covers you can protect your connection to the grounding wire.

Support in stainless steel for Fiber/RRU/Feeder/Power cable in false ceiling. Possible to fasten the endbracket either on to the wall or in the ceiling. Steel wire has a rupture limit at 5.9 kN.

Cable duct footprint: 0,3 m x 1 m


Consist of:
Qty Description
10 Cable Duct, Straight 1m
1
Cable Duct, Straight with grounding space 1m
1
Cable Duct, Straight with ground bar 1m
1
Grounding bar
1
Grounding Bolt Set, (10pcs)
1
Jointing Tube Set, (30pcs)
2
Cable Duct, Cover, 1m
1
Clamp Set, (100 pcs)
1
Cover Screw Set (20pcs)
Product Number
NTM 201 3469/1

Length
1020 mm

Width
600 mm

Product Number
SXK 107 2851/1

Width
300 mm

Height
250 mm

Weight
5.85 kg

Wire Length
50 m

Support in stainless steel for Fiber/RRU/Feeder/Power cable in false ceiling. Possible to fasten the endbracket either on to the wall or in the ceiling. Steel wire has a rupture limit at 5.9 kN.
Height
670 mm

Weight
206 kg

Plastic trunking 6x2000mm Wall mounted 90x61mm with cover for residential and commercial telecom applications. Carries and protects feeder cable, RRU cable, power cable, fiber and grounding cable between antennas
and cabinets. Supplied with accessories for T-joint, L-joint and End cap. Plastic trunking has punched holes in the
base and internal clips (1clip/0.5m) for fastening of cable.
Self-extinguishing
Halogen-free
Lead-free
UV-constant
Shock-proof

Consist of:
Qty Description
1
Wire 100m, Steel 4mm, 72 Stringy
6
Wall Bracket, Steel 110 mm
6
Ceiling Bracket, Steel 70mm
12 Tightening device, Steel
24 Wire Lock, Steel, Max 25mm
Product Number
SXK 107 2852/1

Length
400 mm

Width
300 mm

Height
250 mm

Weight
9.75 kg

Wire Length
100 m

Wire Support Ceiling


Wire support fixed in the ceiling that suspends the steel wire. Distance between wire and ceiling mounted is 38
mm. The wire support are made of High Quality pre-galvanized steel.
Consist of:
Qty Description
1
Cable suspension support 38 mm, Steel

Consist of:
Qty Description
6
Plastic trunking 2000 x 90 x 61 mm
6
Plastic trunking cover 61 mm
2
Internal Corner 90 degree
2
External Corner 90 degree
2
Elbow 90 degree
4
End Cap
Length
2570 mm

Product Number
SXA 120 1873/1

Width
360 mm

Height
290 mm

Width
20 mm

Height
30 mm

Weight
0.15 kg

Wall mounted bracket for the turnbuckle or wire stretcher.Fixed in the wall with anchor bolt or similar strong fastener.

Weight
13.5 kg

Consist of:
Qty Description
1
Wall Bracket 110mm, Hot Dip galvanized
Product Number
SXA 120 1874/1

Wire Suspension Kit 25m


Support in stainless steel for Fiber/RRU/Feeder/Power cable in false ceiling. Possible to fasten the endbracket either on to the wall or in the ceiling. Steel wire has a rupture limit at 5.9 kN.
Consist of:
Qty Description
1
Wire 25m, Steel 4mm, 72 Stringy
2
Wall Bracket, Steel 110 mm
2
Ceiling Bracket, Steel 70mm
2
Tightening device, Steel
4
Wire Lock, Steel, Max 25mm
Length
400 mm

Length
38 mm

Wall Bracket for Turnbuckle

Cable Suspension Support

Product Number
SXK 107 2850/1

Length
400 mm

Wire Suspension Kit 100m

Plastic Trunking

Product Number
NTM 201 4153/1

Consist of:
Qty Description
1
Wire 50m, Steel 4mm, 72 Stringy
4
Wall Bracket, Steel 110 mm
4
Ceiling Bracket, Steel 70mm
8
Tightening device, Steel
16 Wire Lock, Steel, Max 25mm

Length
210 mm

Width
180 mm

Height
170 mm

Weight
9 kg

Bracket for Turnbuckle


Wall mounted bracket for the turnbuckle or wire stretcher.Fixed in the wall with anchor bolt or similar strong fastener.
Consist of:
Qty Description
1
Wall Bracket 110mm, Hot Dip galvanized

Width
300 mm

Height
250 mm

Weight
3.6 kg

Wire Length
25 m

Product Number
SXA 120 1875/1

Length
110 mm

Width
90 mm

Height
50 mm

Weight
9 kg

Ceiling Bracket for Turnbuckle, Beam Mounting


Fix the Bracket on I-beam. Maximum thickness of the I-beam is 20 mm. Attach bracket on wire strecther (hole dimater 11mm). The bracket are made of high grade steel and is hot dip galvanized.
Consist of:
Qty Description
1
Beam bracket, Steel
Product Number
SXA 120 1876/1

22

Length
220 mm

Width
180 mm

Height
160 mm

Weight
10 kg

23

Cable Routing

Cable Routing

Cable Suspension Support

Cable Support Kit (Hoisting Grip)

Beam Clips with Cable Tie Saddle

Cable Support Kit

Solid montage of steel constructions without drilling or welding. Supplied with saddle for attachment of Cable tie.
Rupture limit: 220 N.

End support for three power cables and three OIL cables in the tower and mast, one hoisting grip for each cable.
Three hosting grip for each oval quick link. The oval quick link fitted to the wire loop support.

Consist of:
Qty Description
1
Beam Clamp

Consist of:
Qty Description
2
Wire loop support
2
Oval quick link
3
Hoisting grip 6mm
3
Hoisting grip 12mm
2
Sewing-thread 700mm

Product Number
SXA 120 1870/1
SXA 120 1871/1
SXA 120 1872/1

Length
50 mm
34 mm
400 mm

Width
40 mm
33 mm
266 mm

Height
25 mm
39 mm
280 mm

Weight
0.01 kg
1.437 kg
0.7 kg

Beam Clamp Range


5-9 mm
17-20 mm
10-16 mm

Product Number
NTM 201 3728/1

Length
350 mm

Width
300 mm

Height
10 mm

Weight
0.435 kg

Cable Hanger for Wire


Cable hanger for wire is designed to be fixed on steel wire and to carry cables and fiber.
There are space for 6 cables with a maximum diameter of 16 mm. The bracket are made of steel and it is hot-dip
galvanized.
Consist of:
Qty Description
1
Cable hanger, Steel
Product Number
SXA 120 1877/1

Length
220 mm

Width
180 mm

Height
160 mm

Weight
3 kg

Turnbuckle
The turnbuckle is fixed on the wall/ceiling bracket or on the I-beam bracket. Use it to tighten the steel wire in the
cable suspension system. It is made of steel and hot dip galvanized. Maximum adjustment is 100 mm and eye size is = 9 mm
Consist of:
Qty Description
1
Turnbuckle M10x100mm, Steel
1
Washer M10
1
Nut M10
Product Number
SXA 120 1878/1

Length
170 mm

Width
160 mm

Height
50 mm

Weight
5 kg

Wire Lock
Wire lock for 4 mm steel wire.The wire lock is made of malleable hard iron and it is mounted with 2 pcs on each
wire end.
Consist of:
Qty Description
1
Wire lock 4mm, Malleable hard iron
1
Shackel, Zinc plated steel
2
Nuts, Zinc plated steel
Product Number
SXA 120 1879/1

Length
150 mm

Width
150 mm

Height
30 mm

Weight
1.62 kg

Steel Wire, 4 mm
Steel wire used as cable support in false ceiling, in garage and tunnels. The 4 mm wire is made of zinc plated
steel.
Consist of:
Qty Description
1
100m Wire, Zinc plated Steel, =4mm with 72 core stranded
Product Number
SXA 120 1880/1

24

Length
400 mm

Width
300 mm

Height
250 mm

Weight
6.5 kg

25

Grounding and surge protection

Grounding and surge protection

Grounding Cables

Grounding Cables

Cable Kit 12 m, 35 mm Yellow/Green

Cable Kit 25 m, 35 mm Black

This kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type configuration of
the grounding system with this kit. It is supplied with Main Earth Terminal (MET), branching and connection equipment.

This kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type configuration of
the grounding system with this kit. It is supplied with Main Earth Terminal (MET), branching and connection equipment.

Consist of:
Qty Description
1
Cable 12mx35mm (2 AWG) Cu, Yellow/Green UL 90 C
4
Jointing sleeve C89
6
Serrated washer, 8.4x15
4
Insulation cover
6
Nut M8
4
Cable lug, M8x35mm
6
Washer 8.4x16x1.6
1
Grounding bar, 10x50mm
6
Screw, M8x30 H, St 8.8
2
Screw, 5.5x64mm

Consist of:
Qty Description
1
Cable 25m x 35mm S1Z1-K, Black
10 Nut, M6M M8
2
Grounding bar, 10x50mm
10 Washer, BRB 8.4x16x1.6
8
Cable Lug M10x35mm
10 Screw, M6S M8x30 H St 8.8
8
Cable Lug M8x35mm
4
Screw TKS type nr 12x64
8
Jointing Sleeve, C89
4
Wall Plug
8
Insulating Cover
1
Installation Instruction

Product Number
NTM 201 3669/1

Length
330 mm

Width
330 mm

Height
60 mm

Weight
4.778 kg

Cable Kit 17 m, 35 mm Yellow/Green

Product Number
4/NTM 201 201/2

Length
330 mm

Width
330 mm

This kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type
configuration of the grounding system with this kit. It is supplied with Main Earth Terminal(MET),
branching and connection equipment.

Cable Kit 1 m, 35 mm Yellow/Green

Consist of:
Qty Description
1
Cable 17mx35mm2 (2 AWG) Cu, Yellow/Green UL 90 C
6
Jointing sleeve
8
Serrated washer, 8.4x15
6
Insulation cover
8
Nut, M8
6
Cable lug, M8x35mm
8
Washer, 8.4x16x1.6
2
Grounding bar, 10x50mm
8
Screw, M8x30 H, St 8.8
4
Screw, 5.5x64mm

Consist of:
Qty Description
1
Cable 1m x35mm, Yellow/Green UL 90C
1
Jointing Sleeve, C89
1
Cable lug M8x35mm
1
Insulating Cover

Product Number
NTM 201 3669/2

Length
330 mm

Width
330 mm

Weight
6.942 kg

Consist of:
Qty Description
1
25m x 35mm (2 AWG) Cu Yellow/Green, S1Z1-K UL 90 C
4
Wall Plug
2
Grounding bar, 10x50mm
10 Serrated washer, 8.4x15
8
Cable lug, M10x35mm
10 Nut, M6M M8 ST
8
Cable lug, M8x35mm
10 Washer, BRB 8.4x16x1.6
8
Jointing sleeve, C89
10 Screw, M6S M8x30 H
8
Insulating cover
1
Instruction
4
Screw, TKS NR 12x64
Width
300 mm

Length
140 mm

Width
140 mm

Height
35 mm

Weight
0.48 kg

Height
40 mm

Weight
0.84 kg

Height
40 mm

Weight
0.7 kg

Cable Kit 2 m, 35 mm Yellow/Green


Height
70 mm

This kit is part of the Indoor grounding system for the RBS cabinet. Create a line, ring or tree type configuration of
the grounding system with this kit. It is supplied with Main Earth Terminal (MET), branching and connection equipment.

Length
300 mm

Weight
10.45 kg

Connect cabinets and racks to the indoor grounding system.

Product Number
5/NTM 201 201/3

Cable Kit 25 m, 35 mm Yellow/Green

Product Number
4/NTM 201 201/3

Height
100 mm

Height
80 mm

Connect cabinets and racks to the indoor grounding system.


Consist of:
Qty Description
1
Cable 2m x 35mm Yellow/Green
1
Cable lug M8x35mm
1
Jointing Sleeve, C89
1
Insulating Cover
Product Number
5/NTM 201 201/4

Length
140 mm

Width
130 mm

Cable Kit 2 m, 25 mm Black, Indoor


Connect cabinets and racks to the indoor grounding system.
Consist of:
Qty Description
1
Cable 2mx25 mm, Black S1Z1-K UL 90
1
Jointing Sleeve C89
1
Cable lug M8x25mm
1
Insulating Cover
Product Number
5/NTM 201 201/2
Weight
10.45 kg

Length
140 mm

Width
140 mm

Wire Kit 70 m, 35 mm
Ground the green-field site, roof top site or any outdoor site with a ring conductor arrangement (70m) with this kit.
The ring conductor can be bonded with the MET, the Mast leg, the Cu wire and grounding rods with supplied
parts.
Consist of:
Qty Description
1
70 m x 35 mm Cu-wire, Annealed 7 stringy,
8
Screw, M6S M8x30H
8
Jointing Sleeve, C89
16 Contact Washer, M8
8
Cable Lug, M10x35mm
8
Nut, M6M M8
Product Number
NTM 201 3425/1

26

Length
420 mm

Width
420 mm

Height
140 mm

Weight
22.1 kg

27

Grounding and surge protection

Grounding and surge protection

Grounding Cables

Grounding Cables

Wire Kit 40m, 25mm

Grounding Cable 100 m Bulk Package Black

Creat a ring or line installation around the site with this kit. Branch-off from this ring to earth electrodes to protect
existing or new equipment of shelters, masts, towers or antenna poles. The wire can be used as down conductor
in mast/antennas. ROHS approved kit that gives your grounding system excellent electrical performance. Wire according to Swedish Standard SS240103. Achieve a crimp/branch-off according to SEN24510 and BS 4579:1 with
this kit and the Ericsson approved tools. LTT 601 86 Mechanical crimping tool. LTT 601 89 Hydraulic crimping tool

Indoor grounding wire precut in 100 m length. Multi wire Cu cable with halogen-free sheath. IEC 60228 Class 5
and IEC 60332-1. ROHS approved kit. Rated voltage U0/U: 450/750 V. H07V-K.

Consist of:
Qty Description
1
40m x 25mm Cu Wire, 7-stringy soft annealed, High grade Cu, Diameter 6,4mm
6
Cable Lug M8x25mm, IEC 228 class 5, Tin plated with inspection hole, High grade Cu
6
Jointing sleeve C89,
6
Washer M8, Stainless Steel
6
Bolt M8x30,DIN 933 Stainless Steel
6
Nut M8, Acid proof Steel

Product Number
TEL 901 07/1
TEL 901 08/1
TEL 901 09/1

Product Number
NTM 201 4145/1

Indoor grounding wire precut in 100 m length. Multi wire Cu cable with halogen-free sheath. IEC 60228 Class 5
and IEC 60332-1. ROHS approved kit. Rated voltage U0/U: 450/750 V. H07V-K.

Length
400 mm

Width
400 mm

Height
80 mm

Weight
9.6 kg

Wire Kit 40 m, 35 mm
Creat a ring or line installation around the site with this kit. Branch-off from this ring to earth electrodes to protect
existing or new equipment of shelters, masts, towers or antenna poles. The wire can be used as down conductor
in mast/antennas. ROHS approved kit that gives your grounding system excellent electrical performance. Wire according to Swedish Standard SS240103. Achieve a crimp/branch-off according to SEN24510 and BS 4579:1 with
this kit and the Ericsson approved tools. LTT 601 86 Mechanical crimping tool. LTT 601 89 Hydraulic crimping
tool.
Consist of:
Qty Description
1
40m x 35mm, Flexible Conductor, Annealed 7 Stringy,
6
Cable Lug M10x35mm
6
Serrated Washer M8
6
Jointing Sleeve, C89
6
Nut, M6M M8
6
Screw, M6S M8x30
Product Number
9/NTM 201 230/1

Length
400 mm

Width
400 mm

Height
90 mm

Weight
13.1 kg

Consist of:
Qty Description
1
50mx50mm Flexible Conductor, Annealed 7-stringy
10 Jointing Sleeve, C89
Width
450 mm

Weight
23.5 kg

A kit for grounding of a rooftop site. Use aluminium wire instead of copper cable/wire to reduce the risk of theft at
site. Create a ring or grid configuration with the AL-wire and the supplied jointing clamps. Connect the supplied
AL wire with an external AL grounding wire = 8-10mm in T, X, or parallel joint.
Consist of:
Qty Description
1
40m x 49 mm, Al-wire, 7-strand
6
Joint Clamp, Steel =8-10mm

28

Length
400 mm

Width
400 mm

Colour
Black
Black
Black

Grounding Cable 100 m Bulk Package Yellow/Green

Consist of:
Qty Description
1
100m Grounding Cable
Product Number
TEL 901 07/2
TEL 901 08/2
TEL 901 09/2

Length
100 m
100 m
100 m

Electrical Cross Section (mm)


16
25
35

Colour
Yellow/Green
Yellow/Green
Yellow/Green

Consist of:
Qty Description
1
Cable Flexible, Multi wire copper, Halogen Free IEC 60228 class 5, H07Z1-K
1
Cable lug M8 Tin-plated, Inspection hole, High grade copper IEC 228 class 5
Product Number
RPM 119 1647/1
RPM 119 1647/2
RPM 119 1647/5
RPM 119 1649/1
RPM 119 1649/2
RPM 119 1649/5
RPM 119 1651/1
RPM 119 1651/2
RPM 119 1651/5

Length
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm

Width
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm

Height
10 mm
10 mm
20 mm
10 mm
10 mm
30 mm
20 mm
20 mm
40 mm

Weight
0.265 kg
0.415 kg
0.875 kg
0.355 kg
0.595 kg
1.31 kg
0.455 kg
0.779 kg
1.76 kg

Electrical Cross Section (mm)


16
16
16
25
25
25
35
35
35

Cabinet Grounding Yellow/Green


Height
150 mm

Rooftop Grounding, Aluminium 40 m

Product Number
NTM 201 3755/1

Electrical Cross Section (mm)


16
25
35

Cabinet grounding/Cable Assembly for the indoor Telecom site. Supplied in lenghts of 1, 2 or 5 meter. Cable has
rated Voltage 750 V. It is fire retardant according to IEC 60332-1. ROHS approved kit.

Creat a ring or line installation around the site with this kit. Branch-off from this ring to earth electrodes to protect
existing or new equipment of shelters, masts, towers or antenna poles. The wire can be used as down conductor
in mast/antennas. ROHS approved kit that gives your grounding system excellent electrical performance. Wire according to Swedish Standard SS240103. Achieve a crimp/branch-off according to SEN24510 and BS 4579:1 with
this kit and the Ericsson approved tools. LTT 601 86 Mechanical crimping tool. LTT 601 89 Hydraulic crimping
tool.

Length
450 mm

Length
100 m
100 m
100 m

Cabinet Grounding Black

Wire Kit 50 m, 50 mm

Product Number
9/NTM 201 230/4

Consist of:
Qty Description
1
100m Grounding Cable

Height
100 mm

Weight
6 kg

Cabinet grounding/Cable Assembly for the indoor Telecom site. Supplied in lenghts of 1, 2 or 5 meter. Cable has
rated Voltage 750 V. It is fire retardant according to IEC 60332-1. ROHS approved kit.
Consist of:
Qty Description
1
Cable Flexible, Multi wire copper, Halogen Free IEC 60228 class 5, H07Z1-K
1
Cable lug M8 Tin-plated, Inspection hole, High grade copper IEC 228 class 5
Product Number
RPM 119 1648/1
RPM 119 1648/2
RPM 119 1648/5
RPM 119 1650/1
RPM 119 1650/2
RPM 119 1650/5
RPM 119 1652/1
RPM 119 1652/2
RPM 119 1652/5

Length
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm

Width
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm
220 mm

Height
10 mm
10 mm
20 mm
10 mm
10 mm
30 mm
20 mm
20 mm
40 mm

Weight
0.265 kg
0.415 kg
0.875 kg
0.355 kg
0.595 kg
1.31 kg
0.455 kg
0.779 kg
1.76 kg

Electrical Cross Section (mm)


16
16
16
25
25
25
35
35
35

29

Grounding and surge protection

Grounding and surge protection

Grounding Cables

Grounding Bars and Rods (combined)

Indoor Grounding 3/8 - 1 5/8

Grounding Bar

This kit connects 3/8" - 1 5/8" feeder with the indoor grounding system.

Grounding bar for Telecom mast, tower and city site. Fasten this ground bar around tower tower leg or pipe with
diameter = 42-76 mm. Possible to fasten it against anchor rail and cable ladder.
The grounding bar has ten M8 connections for grounding with cable lug.

Consist of:
Qty Description
1
Hose Clip
1
Cable, 1x25mm, 2m
1
Insulating cover
1
Jointing Sleeve C89
1
Cable lug, 25mm
Product Number
NTM 201 219/1

Length
210 mm

Width
160 mm

Height
30 mm

Weight
0.65 kg

Indoor Quick Grounding 16 - 35 mm, Bulk pack


The UL-listed and patented ground wire connector joints two insulated multi-threaded Wires. Connected 2 wires
with outer dimension 7.5-11,5mm and electrical cross section 16-35mm (AWG2 - AWG6). Use it indoors for
electrical feed thru and taps in the grounding and battery back-up system. Approved for use in telecom networks,
minimum 20 years lifetime.
Quick and easy product to use in a narrow space. Installer does not need any press tool for the connection of
wires. Tighten with supplied tool or with cordless screwdriver LTT 129 09/2 and suitable bit.

The Quickgrip grounding joints cable with electrical cross section according to table below.
Cross section 1 - Cross section 2
16mm - 16mm
16mm - 25mm
16mm - 35mm
25mm - 25mm
25mm - 35mm
35mm - 35mm
Consist of :
Qty Description
10
Grounding connector 7.5-11,5mm, 25-35mm, UL listed patented,
1
Tool
Length
170 mm

Width
210 mm

Height
90 mm

Weight
0.87 kg

Grounding kit for the antenna system. Grounds TMA, RRU or filters at the Telecom site. ROHS2 approved kit with
high quality components.
Consist of:
Qty Description
1
Grounding wire 16mm2, halogen free,
2
Cable lug 16mm2
1
Bolt, M6S M8x25 acid proof steel
2
Nut, M6S M8, acid proof steel
2
Washer, BRB M8,acid proof steel
1
Spring washer, FBB M8,acid proof steel
2
Heat shrink,25mm 12x2mm

Width
220 mm

Height
60 mm

Weight
0.76 kg

Rod kit, 3 m

Length
30 mm

Consist of:
Qty Description
2
Earth rod, 1500mm, =5/8"
1
Cable clamp 5/8" / 25-50mm
1
Tip
1
Coupling
1
Driving stud
Product Number
9/NTM 201 230/2

Length
1505 mm

Width
80 mm

Height
35 mm

Weight
4.1 kg

Tin plated high grade copper bar for the indoor Telecom Site. Insulated for mount on wall or fitting profile. It connects multi-stranded Cu wires with electrical cross section up to 50 mm.
Consist of:
Qty Description
1
Main Earth Terminal
Product Number
NGT 901 30/1
NGT 901 30/2

Length
180 mm
105 mm

Width
40 mm
40 mm

Height
20 mm
20 mm

Weight
0.26 kg
0.145 kg

Connections
10
5

Insulated Grounding Bar


Grounding bar designed for lightning protection and potential equalization. Can be mounted in outdoor industrial
environments. Supplied with plugs for wall montage. Lightning protection according to DIN V VDE V 0185 part 3
and Swedish standard SS EN 62305. Compliant with DIN VDE 0100 part 400 and part 540.

Width
150 mm

Height
200 mm

Weight
0.3 kg

Consist of:
Qty Description
1
Grounding bar High grade Stainless steel
2
Insert screw M10x80mm
2
Plastic plug
2
Spring Washer 10,5x20x1
2
Insulators
10 M10 Connectors High grade Stainless steel
Product Number
SXK 107 2847/1

30

Length
350 mm

Main Earth Terminal

Grounding Kit Antenna System

Product Number
NTM 201 4031/1

Product Number
NTM 201 3326/1

System for deep grounding at green field site, container site or any outdoor site without any central grounding
system. The rod kit can be used to either achieve a good lightening protection or to balance the electric potential
in the outdoor grounding system. Supplied with connector for 25-50mm grounding wire.

Storage -25C to +55C


Transport -40C to +70C

Product Number
NTM 201 3657/1

Consist of:
Qty Description
1
Grounding bar 10xM8
1
VU-Bolt, M10 M8 CC-90
2
Screw, MC6S 6x20H
10 Screw, MC6S 8x20H
20 Washer, AZ 8.4
10 Washer, 8.4
2
Washer, AZ 6.4
2
Washer, 6.4
2
Washer, =10.5x20mm
10 Nut, M6M M8
4
Nut, M6M M10

Length
408.5 mm

Width
40 mm

Height
6 mm

Weight
1.9 kg

31

Grounding and surge protection

Grounding and surge protection

Grounding Bars and Rods (combined)

Grounding Cable Lugs

Potential Grounding PBC 6100, SSC-02

Cable lug M8, Bulk pack

This kit grounds the PBC 6100 and SSC02.

Tin-plated high grade copper M8 Cable lug in bulk package. Crimp on power and grounding cable at indoor/outdoor. Telecom site. It fits multi stranded wire, stranded wire as well as round conductor of copper. Inspection hole
for a direct visual quality control of the crimp. Crimp on IEC 60228 Class 5 wire. ROHS approved.

Ground Bar Connects


1 wire x = 8-10 mm
7 wire x max 25 mm
1 band x 4x30 mm

Achieve a Crimp/Connection according SEN 24510 and BS 4579:1 with ericsson approved tools LTT 601 86 or
LTT 601 89.

ROHS 2 compliant Kit

Consist of:
Qty Description
100 M8 Cable Lug

Consist of:
Qty Description
7
Grounding wire16mm2, AWG5, IEC 60228 Class 5, Halogen Free
12 Cable lug , 16mm2, Hole = 8 mm
1
Ground Bar 7x16mm2, Cover
4
Screw/Nut/Washer kit M6x12mm
Product Number
NTM 201 1217/1

Length
300 mm

Width
300 mm

Height
300 mm

Weight
1.589 kg

Jointing Sleeve C89, Bulk Pack


The sleeve joint/branch off thready Cu wires in the grounding and lightning protection system. Range of application is indoors, outdoors and even in the ground. Crimp wire and sleeve with tool LTT 601 86 or LTT 601 89 to
achieve a connection according to SEN 24510 and BS 4579:1. Jointing sleeve made of tin plated high grade Cu
ROHS2 compliant.
The sleeve branch of IEC 228 Class 2 and IEC 228 class 5
wires with following Wire cross section.

Height
90 mm
90 mm
90 mm

Weight
0.85 kg
1.3 kg
2.5 kg

Electrical Cross Section


16 mm
25 mm
35 mm

Tested for a maximum voltage of 47 kV.


ROHS2 Approved
Mainly used for mount against Main Earth Terminal (MET) or appliance plug of material Cu.
Consist of:
Qty Description
100 M10x35mm Tin-plated,High Grade Cu, with inspection hole
Length
90 mm

Width
140 mm

Height
80 mm

Weight
2.4 kg

Cable lug Kit, 50 and 70 mm


Used when connecting the RBS to the earthing system. Use the crimping tool set LTT 601 86/89 to accomplish a
correct crimp.
Consist of:
Qty Description
2
Cable lug, =50mm , hole 8mm
2
Cable lug, =70mm , hole 8mm

Consist of:
Qty Description
50 Jointing Sleeve C89
Length
150 mm

Width
85 mm

Height
85 mm

Weight
1.9 kg

Jointing Sleeve C89


The sleeve joint/branch off thready Cu wires in the grounding and lightning protection system. Range of application is indoors, outdoors and even in the ground. Crimp wire and sleeve with tool LTT 601 86 or LTT 601 89 to
achieve a connection according to SEN 24510 and BS 4579:1. Jointing sleeve made of tin plated high grade Cu
ROHS2 compliant.
The sleeve branch of IEC 228 Class 2 and IEC 228 class 5
wires with following Wire cross section.

Product Number
NTM 202 187/1

Width
19 mm

Width
60 mm

Height
20 mm

Weight
0.15 kg

Surge Protection
DC Power Grounding
A grounding kit that is suitable for grounding of 12-30 mm coaxial cables and shielded power cables such as the
DC power cable for the RRU. Waterproof sealing.

Product Number
NGT 901 21/1

Consist of:
Qty Description
1
Jointing Sleeve C89
Length
30 mm

Length
60 mm

Consist of:
Qty Description
1
Contact bar ., 3/8., 5/8. 7/8
1
Copper mesh
1
Socket head cap
2
Self-amalgating tape
1
Cable assembly 500mm, 16 mm
2
Cable lug = 8 , 16 mm

Cu Wire 1 - Cu Wire 2
16 mm - 35 mm
16 mm - 50 mm
25 mm - 25 mm
25 mm - 50 mm
35 mm - 35 mm
35 mm - 50 mm
50 mm - 50 mm

32

Width
90 mm
90 mm
90 mm

Cable lug M10, Bulk pack

Product Number
NTM 201 3477/1

Cu Wire 1 - Cu Wire 2
16 mm - 35 mm
16 mm - 50 mm
25 mm - 25 mm
25 mm - 50 mm
35 mm - 35 mm
35 mm - 50 mm
50 mm - 50 mm

Product Number
SNT 102 26

Length
70 mm
150 mm
150 mm

Tin-plated non-isolated cable lugs in bulk pack. Use these cable lugs for connection and termination of Cu multithreaded wire, few-threaded wire as well as solid round conductor. Connect power cable, grounding cable or surge arrest cables (IEC 228 Class 2 and IEC 228 Class 5) at Telecom site. Use together with Ericsson approved
crimping tool LTT 601 86 or LTT 601 89 to achieve a crimp according SEN 24510 and BS 4579:1

Grounding Joint Clamps

Product Number
SNT 901 14/1

Product Number
SNG 904 60/1
SNG 904 60/2
SNG 904 60/3

Height
16 mm

Length
200 mm

Width
180 mm

Height
30 mm

Weight
0.161 kg

Weight
0.042 kg

33

Grounding and surge protection

Cables

Surge Protection

Coaxial Cables
Feeder Grounding Quickgrip

1/2" Jumper Cables

The Quickgrip feeder grounding protects feeder cable and radio equipment against surge from lightening stroke. It
connects corrugated Cu feeder with size 1/2", 7/8", 1-1/4" or 1-5/8" against MET/tower/mast with M8 Bolt. The sealing/connection between Quickgrip and corrugated Cu feeder is quick, simple and does not need any tool for installation. Saves up to 80% in installation time against traditional grounding of feeder cable.

Product Number
TSR 951 331/1
TSR 951 331/2
TSR 951 331/3
TSR 951 331/5
TSR 951 333/1
TSR 951 333/2
TSR 951 333/3

- IP67 approved
- No preparation of the cable is needed
- No tools needed for installation
- No use for additional sealing
- Available in 4 dimensions 1/2 1 5/8
- Contact resistance <1m
- Current impulse test 8/20 100kA
- Current impulse test 10/350 10kA

Length
140 mm
160 mm
170 mm
170 mm

Width
140 mm
130 mm
100 mm
80 mm

Width
300 mm
350 mm
450 mm
500 mm
450 mm
430 mm
420 mm

Height
15 mm
15 mm
15 mm
50 mm
30 mm
35 mm
30 mm

Weight
0.38 kg
0.6 kg
0.775 kg
1.146 kg
0.51 kg
0.708 kg
0.914 kg

Type
1/2" 7/16 M - 7/16 M
1/2" 7/16 M - 7/16 M
1/2" 7/16 M - 7/16 M
1/2" Angle 7/16 M - 7/16 M
1/2" Angle 7/16 M - 7/16 M
1/2" Angle 7/16 M - 7/16 M
1/2" Angle 7/16 M - 7/16 M

Accessories

Consist of:
Qty Description
1
Quickgrip Feeder grounding L=0.6m x 16mm
2
Hexagon bolt M8x25
2
Hexagon nut M8
4
Spring Washer
Product Number
NGT 901 20/1
NGT 901 20/2
NGT 901 20/3
NGT 901 20/4

Length
1000 mm
2000 mm
3000 mm
5000 mm
1500 mm
2500 mm
3000 mm

ESB Cable
This cable is used for synchronisation of RBS 2106 cabinets.

Height
30 mm
40 mm
60 mm
110 mm

Weight
0.19 kg
0.252 kg
0.31 kg
0.37 kg

Size
1/2"
7/8"
1 1/4"
1 5/8"

Surge Arrestor
Wide Band Surge Arrester

Consist of:
Description
ESB Cable
ESB Cable
ESB Cable
ESB Cable
ESB Cable

Cable 4x2
3,240 m
7,020 m
12,420 m
25,380 m
75,060 m

Product Number
NTM 201 3072/1
NTM 201 3072/2
NTM 201 3072/3
NTM 201 3072/4
NTM 201 3072/5

Label holder
2
2
2
2
2
Length
3240 mm
7020 mm
12420 mm
25380 mm
75060 mm

Cable clamp
2
2
2
2
2
Width
150 mm
220 mm
220 mm
220 mm
230 mm

Connector
1
1
1
Height
30 mm
20 mm
30 mm
90 mm
120 mm

Cover shield
1
1
1
Weight
0.18 kg
0.37 kg
0.59 kg
1.06 kg
3.15 kg

The surge arresters protects electronic equipment against lightning overvoltage transients. The arrester is mounted preferable between the jumper/feeder and cabinet.
Impedance: 50 ohm
Nom. DC spark-over voltage: 90V
Insertion loss: <= 0.1 dB
2002/95/EC (RoHS) compliant
NGC 901 42/3 and NGC 901 46
Temperature range -45C to +85C
Rapid change of temperature IEC 60068-2-14 Test Na
Corrosion salt mist IEC 60068-2-11 Test Ka
Vibration IEC 60068-2-6 Test Fc
Shock IEC 60068-2-27 Test Ea
Climatic class IEC 60068-1 (45/85/56)
Cold IEC 60068-2-1 Test A
Dry heat IEC 60068-2-2 Test B
Damp heat (steady state) IEC 60068-2-3 Test Ca
Degree of protection(mated pair)IEC 60529, IP68 2.5 bar, mated condition
NGC 901 42/3
Temperature range -25C to +85C
Thermal shock: MIL-STD-202, Meth. 107, Cond. B
Corrosion MIL-STD-202, Meth. 101, Cond. B
Vibration MIL-STD-202, Meth. 204, Cond. B
Shock MIL-STD-202, Meth. 213, Cond. I
Moisture resistance MIL-STD-202, Meth. 106
Degree of protection (mated pair) IEC 60529, IP68
Product number
NGC 901 42/3
NGC 901 46

Operating Frequency
DC-3000 MHz
1.7-12,698-2700 MHz

Product Number
NGC 901 46

Length
126 mm

Type
N Female - N Female
7/16 Female - 7/16 Male
Width
35 mm

Height
61 mm

Discharge tube
90 V, included
90 V, included
Weight
0.519 kg

Discharge Tube 90V


Replacement for damaged discharge tubes. Fits the Wide Band Surge arresters of N and 7/16 DIN type.
e.g. NGC 901 46. Diameter = 6mm, Height = 8 mm
Consist of:
Qty Description
1
90V Gas Discharge Tube
Product Number
NGC 901 46/1

34

Length
6 mm

Width
6 mm

Height
8 mm

Weight
0.002 kg

35

Cable Clamps

Cable Clamps

Fiber and Power Clamps

Feeder clamps
Double Stack Feeder Clamp 1/2"

Power/Optical Fibre Clamp Bulk pack

The 1/2" (16 +/-1mm) clamp is designed to secure 1 to 6 feeder cables at any telecom site. Clamp it up on cable
ladder, rung, bracket, I-beam, profile lattice mast etc. Requires only standard tools and is easy to mount and
handle. It withstands wind speeds up to 60 m/s. The protected design prevents damage of feeder even if over-torque at assembly is used. Recommended clamping distance is max 0.8 meter. The
U-bar has a width of opening of 20 +/-0.5 mm. ROHS compliant.

The clamp is designed to secure Optical fiber and power cable/assembly in the Main-remote system
It can be installed on cable ladder, rung, bracket, i-beam and fitting profile. It secures fibre with diameter = 4.5 6.5 mm and Power cables with diameter = 9.0-13.0 mm. U-bar aperture/Width of opening: 20 mm +-0.5 [mm].
Maximum Clamping distance: max 0.5 meter. ROHS compliant. Supplied in package of 10 pcs.

Consist of:
Qty Description
3
Plastic clamp 2 x
1
U-bar ,t=5mm
1
Threaded rod M6
1
Hex cap screw
2
Flange nut
Product Number
NTM 201 1223/2
NTM 201 1223/4
NTM 201 1223/6

Length
117 mm
140 mm
160 mm

Width
16 mm
16 mm
16 mm

Height
85 mm
85 mm
85 mm

Weight
0.15 kg
0.21 kg
0.27 kg

Clamps
2
4
6

Double Stack Feeder Clamp 7/8"


The 7/8" (28 +/-1mm) clamp is designed to secure 1 to 6 feeder cables at any telecom site. Clamp it up on cable
ladder, rung, bracket, I-beam, profile lattice mast etc. Requires only standard tools and is easy to mount and
handle. It withstands wind speeds up to 60 m/s. The protected design prevents damage of feeder even if overtorque at assembly is used. Recommended clamping distance is max 0.8 meter. The
U-bar has a width of opening of 20 +/-0.5 mm. ROHS compliant.
Consist of:
Qty Description
1
U-bar ,t=5mm
1
Threaded rod M6
1
Hex cap screw M8
2
Hex flange nut M6
Product Number
NTM 201 1224/2
NTM 201 1224/4
NTM 201 1224/6

Length
110 mm
150 mm
190 mm

Width
50 mm
50 mm
50 mm

Height
86 mm
86 mm
86 mm

Weight
0.16 kg
0.235 kg
0.305 kg

Clamps
2
4
6

Double Stack Feeder Clamp 1 1/4"


The 1-1/4" (40 +/-1mm) clamp is designed to secure 1 to 6 feeder cables at any telecom site. Clamp it up on cable ladder, rung, bracket, I-beam, profile lattice mast etc. Requires only standard tools and is easy to mount and
handle. It withstands wind speeds up to 200 Km/h. The protected design prevents damage
of feeder even if over-torque at assembly is used. Recommended clamping distance is as table below and the Ubar has a width of opening of 20 +/-0.5 mm. ROHS compliant.
Consist of:
Qty Description
1
U-bar ,t=5mm
1
Threaded rod M6/M8
1
Hex cap screw M8
2
Flange nut M6/M8
Product Number
NTM 201 1225/2
NTM 201 1225/4
NTM 201 1225/6

Length
132 mm
182 mm
257 mm

Width
27 mm
27 mm
27 mm

Height
155 mm
155 mm
155 mm

Weight
0.181 kg
0.283 kg
0.37 kg

Clamps
2
4
6

Double Stack Feeder Clamp 1-5/8"

Consist of:
Qty
Description
1
U-bar, Acid proof stainless steel
1
Threaded rod, Acid proof stainless steel
2
Nut/Washer, Acid proof stainless steel
1
Securing Bolt, Acid proof stainless steel
1,2,3 Power Bushing, EPDM
1,2,3 Opto Bushing, EPDM
2,4,6 Clamp, Plastic
Product Number
NTM 201 4156/1
NTM 201 4156/2
NTM 201 4156/3

Length
270 mm
270 mm
270 mm

Width
240 mm
280 mm
320 mm

Height
85 mm
85 mm
85 mm

Weight
1.6 kg
2.15 kg
2.75 kg

Power x Opto, Max


1 x 1 pcs
2 x 2 pcs
3 x 3 pcs

Hybrid Clamp, Bulk pack


The clamp is designed to secure the hybrid cable in the Main-remote system. It can be installed on cable ladder,
rung, bracket, i-beam and fitting profile. It secures cable with diameter = 21, 25.5 mm or 30 mm.
U-bar aperture/Width of opening: 20 mm +-0.5 [mm]. Maximum clamping distance: max 0.8 meter. ROHS compliant. Supplied in bulk package of 10 pcs.
Consist of:
Qty Description
1
U-bar, Acid proof stainless steel
1
Threaded rod, Acid proof stainless steel
2
Nut/Washer, Acid proof stainless steel
1
Securing Bolt, Acid proof stainless steel
2
Clamp, Plastic
Product Number
NTM 201 4157/1
NTM 201 4157/2
NTM 201 4157/3

Length
300 mm
300 mm
300 mm

Width
240 mm
250 mm
260 mm

Height
85 mm
86 mm
86 mm

Weight
1.5 kg
1.6 kg
2 kg

Cable Diameter
21 mm
25.5 mm
30 mm

Multi Diameter Clamp


The Multi Diameter Clamp is designed to secure 2 to 6 cables between 22 - 41mm.
The Multi Diameter Clamp can be installed on cable ladders, brackets, i-beam profi les etc.
Maximum clamps distance: max 0.8 meter
ROHS compliant.
Supplied in bulk package of 10 pcs
Consist of:
Qty
Description
1
U-bar, Acid proof stainless steel
1
Threaded rod, Acid proof stainless steel
2
Nut/Washer, Acid proof stainless steel
1
Securing Bolt, Acid proof stainless steel
2,4,6 Clamp, Plastic
Product Number
NTB 101 217/1
NTB 101 217/2
NTB 101 217/3

Length
150 mm
220 mm
300 mm

Width
120 mm
120 mm
120 mm

Height
50 mm
50 mm
50 mm

Weight
0.3kg
0.4 kg
0.5 kg

Clamps
2
4
6

The 1-5/8" (50+/-1mm) clamp is designed to secure 1 to 6 feeder cables at any telecom site. Clamp it up on cable
ladder, rung, bracket, I-beam, profile lattice mast etc. Requires only standard tools and is easy to mount and
handle. It withstands wind speeds up to 200 Km/h. The protected design prevents damage of feeder even if overtorque at assembly is used. Recommended clamping distance is as table below
and the U-bar has a width of opening of 20 +/-0.5 mm. RoHS compliant.
Consist of:
Qty Description
1
U-bar ,t=5mm
1
Threaded rod M6/M8
1
Hex cap screw M8
2
Hex flange nut M6/M8
Product Number
NTM 201 1226/2
NTM 201 1226/4
NTM 201 1226/6

36

Length
152 mm
227 mm
287 mm

Width
33 mm
33 mm
33 mm

Height
130 mm
130 mm
130 mm

Weight
0.213 kg
0.353 kg
0.466 kg

Clamps
2
4
6

37

Cable Sealing

Cable Sealing

Cable Sealing Kits

Cable Sealing Kits

ComPlus 6x1, 1/4 - 7/8

Cable Sealing Swan Neck x 16

The frame has integrated knockout cover that are easily removed before routing cables. The 6 smaller modules fit
cables from dimensions from 1/4" up to 1/2". The 12 larger modules fit cables from 3/8" up to 7/8". One single
multidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a perfect installation achieved. ComPlus is certified according to IEC 60529 to IP 66/67.

Swan neck SLF 127 is area efficient cable sealing solutions for RRU cables on roof tops. The seals are adaptable
to cables of different sizes through sealing modules with removable layers. The use of Multidiameter, speeds up
installation and reduces the need for stock, material and logistics. The built-in spare capacity simplifies future
upgrades.

Consist of:
Qty Description
2
Side section composite frame
1
Module set 1/4" - 7/8"

Aperture dimensions Hole/frame


NTM 201 4150/1 131.7/183 mm

Product Number
NTM 201 3448/1

Length
380 mm

Width
270 mm

Height
160 mm

Consist of:
Qty Description
1
SvanNeck
1
Sealing Washer
16 Multidiameter Sealing. Sealing range: 0+3.5-16.5 mm (0+0.138-0.650")

Weight
5.6 kg

ComPlus 6x2, 1/4 - 7/8


The frame has integrated knockout cover that are easily removed before routing cables. The 3 smaller module fits
cables with dimensions from 1/4" up to 1/2". The larger module fits cables with dimensions from 3/8 " up to 7/8".
One single multidiameter module can seal cables of several different diameters, simply by peeling layers away from
the module halves until a perfect installation achieved. ComPlus is certified according to IEC 60529 to IP 66/67.
Consist of:
Qty Description
2
Side section composite frame
1
Mid section composite frame
1
Module set 1/4" - 7/8"
Product Number
NTM 201 3448/2

Length
300 mm

Width
250 mm

Height
250 mm

The frame has integrated knockout cover that are easily removed before routing cables. The 6 modules fits cables
with dimensions from 7/8" up to 1 - 5/8". One single multidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a perfect installation is achieved. ComPlus is
certified according to IEC 60529 to IP 66/67.
Consist of:
Qty Description
2
Side section composite frame
1
Module set 7/8" - 1 5/8"
Length
390 mm

Width
260 mm

Height
150 mm

Weight
5.3 kg

The frame has integrated knockout cover that are easily removed before routing cables. The 6 modules fit cable
with dimensions from 7/8" to 1 - 5/8". One single multidiameter module can seal cables of several different diameters, simply by peeling layers away from the module halves until a perfect installation is achieved. ComPlus is certified according to IEC 60529 to IP 66/67.

Width
250 mm

Height
250 mm

Height
293 mm

Weight
8.6 kg

Max RRU Sealing


16 pcs

Cable Sealing Round Frame, 4-17 mm


The RS Round frame is a seal for singel cable or pipe entries in metal sleeves or core drilled holes.
Install it in concrete-, sandwich- or building constructions. The two halves with multidiameter technology, are adjustable to fit different cabel or pipe diameters. The split construction makes it easy to install arount previously installed cables and pipes. It can be used for a single grounding wire or optical fiber as well as feeder cable. Sealing
is according to IP 66/67 Firestop.

Product Number
NTM 201 3656/1

Length
44 mm

Width
31 mm

Height
37 mm

Weight
0.06 kg

Fiber/Cable/Pipe
4-17 mm (1/4"-1/2")

Cable Sealing Round Frame, 8-30 mm


The RS Round frame is a seal for singel cable or pipe entries in metal sleeves or core drilled holes.
Install it in concrete-, sandwich- or building constructions. The two halves with multidiameter technology, are adjustable to fit different cabel or pipe diameters. The split construction makes it easy to install arount previously installed cables and pipes. It can be used for a single grounding wire or optical fiber as well as feeder cable. Sealing
is according to IP 66/67 Firestop.

Product Number
NTM 201 3656/2

Length
86 mm

Width
50 mm

Height
60 mm

Weight
0.3 kg

Fiber/Cable/Pipe
8-30 mm (3/8"-7/8")

Sealing for Main Remote/RRU


ComSeal is a light-weight and area efficient cable sealing solution for max 12 RRU cables in the radio-remote
system. Typical for installation of telecom equipment on buildings or shelters. It is equipped with adaptable sealing modules and supplied as ready-made kit. The seals are adaptable to cables of different sizes (3.5 -16.5mm)
through sealing modules with removable layers. The use of Multidiameter, speeds up installation and reduces
the need for stock, material and logistics. The built-in spare capacity simplifies future upgrades. Sealing according
to IP55. Sealing diameter: 3.5-16.5 mm (0.138"-0.650").

Consist of:
Qty Description
2
Side section composite frame
1
Mid section composite frame
1
Module set 7/8" - 1 5/8"
Length
300 mm

Width
382 mm

Consist of:
Qty Description
1
Round Frame RS
2
Multidiameter Half

ComPlus 6x2, 7/8 - 1 5/8

Product Number
NTM 201 3449/2

Length
213 mm

Consist of:
Qty Description
1
Round Frame RS
2
Multidiameter Half

Weight
6.5 kg

Complus 6x1, 7/8 - 1 5/8

Product Number
NTM 201 3449/1

Product Number
NTM 201 4150/1

Weight
6.3 kg

Cable Sealing Swan Neck x 4


Swan neck SLF 70 is area efficient cable sealing solutions for RRU cables on roof tops. The seals are adaptable to
cables of different sizes through sealing modules with removable layers. The use of Multidiameter, speeds up
installation and reduces the need for stock, material and logistics. The built-in spare capacity simplifies future
upgrades.
Aperture dimensions Hole/frame
NTM 201 4149/1 82,5/ 130 mm

Consist of:
Qty Description
1
Frame
6x2 Multidiameter Sealing. Sealing diameter: 3.5-16.5 mm (0.138"-0.650").
1
Assembly Gel
1
Instruction
4
Nut/Washer/Screw M8x20
Product Number
NTM 201 4092/1

Length
211 mm

Width
80 mm

Height
57 mm

Weight
0.6 kg

Sealings
12

Consist of:
Qty Description
1
SvanNeck
1
Sealing Washer
4
Multidiameter Sealing. Sealing range: 0+3.5-16.5 mm (0+0.138-0.650")
Product Number
NTM 201 4149/1

38

Length
160 mm

Width
293 mm

Height
207 mm

Weight
3.8 kg

Max RRU Sealing


4 pcs

39

Cable Sealing

Cable Sealing

Cable Sealing Kits

Cable Sealing Kits

Comshelt

Shrink Sleeve Splice

The C ComShelt seal is a light-weight solution designed to help you maximize uptime in your telecom network.
It protects equipment from water, dust and rodents, and fits cables of different sizes thanks to
Multidiameter, an adaptability solution based on flexible sealing modules. The seals are adaptable to cables of
different sizes through sealing modules with removable layers. When used with a solid core, the modules function
as spare modules for future capacity.

Cold Shrink sleeve that seals RF joints in the Telecom RAN. The termination outer layer tube provides weather-resistance and sealing over the cable and connector. The termination inner layer tube provides reinforced mechanical protection. The installation does not need any additional tools or components. Note: Slip Shrink Sleeve over
coaxial cable before connecting it with second coaxial cable.

Weather-proof: IP55
Wall/roof Aperture dimensions: 190x300 [mm], 7.480 x 11.811 [Inch]
Consist of:
Qty Description
1
Composite Frame with integrated compression unit
6
Multidiameter module, Range: 0+3.5-16.5 [mm], 0+0.138-0.650 [inch]
12 Multidiameter module, Range: 0+9.5-32.5 [mm], 0+0.374-1.280 [inch]
Product Number
NTM 201 3216/1

Length
390 mm

Width
250 mm

Height
80 mm

MPB 134 02/1 Seals the joint between coaxial connectors for example up in the mast/tower
1/2" Coaxial Cable
1/2" Coaxial Cable ( 7/16 DIN connectors)
1/2" Coaxial Cable
7/8" Coaxial Cable ( 7/16 DIN connectors)
1/2" Coaxial Cable
1/2" Coaxial Cable ( N connectors)
1/2" Coaxial Cable
7/8" Coaxial Cable ( N connectors)
Sealing intervall outer jumper/connector diameter = 13 - 39 mm
Lenght of sealing 300 mm

Weight
2.6 kg

Sealing according to: IEC 68, IEC 721


Product Number
MPB 134 02/1

Length
300 mm

Width
43 mm

Height
56 mm

Weight
0.18 kg

Fiber Sealing, 3x3.5-5.0 mm


Screw Cap with PG 16 thread for 1-3 fibers. It seals fibers with diameter 3,5-5,0 mm. Installing temperature: [-30,
+100] C
Product Number
NDM 902 025/1

Length
41 mm

Width
30 mm

Height
41 mm

Weight
0.017 kg

Cable Sealing Macro Sites Feeder/Power/Fiber


Basic cable entry seal for standard applications in Main Remote system (Macro sites). Cabel entry seal for feeder
cable, power cable or fiber cable. 6 available seals for feeder cable size 1/2", 1/4" and 7/8". 6 available seals for
fiber and/or Power cable 4.5mm 15mm. IP-55. UV resistant. ROHS compliant.
Consist of:
Qty Description
1
Frame
1
Compress Unit
2
7/8'' Base Clamp
1
Compress Plate
6
1/2Jumper Sealing
3
Compress Screw
6
1/4Jumper Sealing
3
Washer 8
6
13.5 Plug
6
Sealing washer 8
1
Cable Base Clamp
1
Sealing Tape
6
Cable Sealing
1
Lubrication oil
6
Cable Plug
1
Self-amalgating tape
Product Number
NTM 201 3879/1

Weather Sealing Closures


These weather sealing closures protect the jumper-to-antenna and jumper-to-RRU/TMA joints. The sealing closure protects DIN 7-16 RF connections in the RAN from moisture, ice, dust, and rain. Use the closures on the outdoor telecom mast, telecom tower, or roof top sites. Designed with compliant sealing gel that completely covers the
RF connection joint.
Features:
- IP68 protection level
- Easy to install - no tools needed
- Simple, robust design
- One-handed installation
- Re-enterable and re-usable
- Very compact
- Icing/freezing rain tolerance per MIL-STD-810
- Blowing rain tolerance per GR-3151-CORE
Operating temperature: -40 to +65C
Transportation and storage temperature: -40to +65C
Installation/removal temperature: 0 to 40C
Jumper cable diameter: 13.5 - 16mm
Radial clearance to nearest obstruction: 6.35mm
Consist of:
Qty Description
1
Compression Sleeve
1
Gel Web Holder
Product Number
MPB 901 029/1

Length
226 mm

Width
162 mm

Height
178 mm

Weight
1.8 kg

Sealing Set
Length
170 mm

Width
175 mm

Height
20 mm

Weight
3 kg

Shrink Sleeve Termination


Cold Shrink sleeve that seals RF joints in the Telecom RAN. The termination outer layer tube provides weather-resistance and sealing over the cable and connector. The termination inner layer tube provides reinforced mechanical protection. The installation does not need any additional tools or components. Note: Slip Shrink Sleeve over
your jumper before connecting it with the connector.

Use this sealing set to seal a splice in the RF system on a Telecom site. It protects the splice against vibrations,
moisture and dust. Designed for feeder sizes 1/2", 7/8", 1-5/8", 1-1/4". This kit can be used to seal already installed equipment.
Consist of:
Qty Description
1
Tape, self-fusing, l=9.15 m; w=19 mm
1
Electrotape PVC, l=20.1 m; w=19 mm
Product Number
NTM 201 2426

Length
310 mm

Width
220 mm

Height
150 mm

Weight
0.3 kg

Sealing intervall outer jumper/connector diameter = 13 - 39 mm


Lenght of sealing: 150 mm
Sealing according to: IEC 68, IEC 721
MPB 134 01/1 Seals the termination of jumper close to the antenna/TMA
N connector
1/2" Jumper cable
N connector
7/8" Jumper cable
7/16 DIN connector
1/2" Jumper cable
7/16 DIN connector
7/8" Jumper cable
Product Number
MPB 134 01/1

40

Length
150 mm

Width
43 mm

Height
56 mm

Weight
0.08 kg

41

Cabinets and frames

Cabinets and frames

Frames

Cabinet and Frame Accessories


Rack frame 16U, Paint coated, Grey

Cross Connection Set

A 19" standard rack according to IEC 297 intended for mounting on wall, delivered with 4 support bars. Rack
height is 714 mm (16U) and wall distance 420 mm.

The Cross Connection unit is a for indoor 19" rack. It can hold totally 20x10-pair terminal blocks.

Consist of:
Qty Description
2
Uprights 16 Unit
1
Assembly screw/nut set, M6x12mm (20pcs)
4
Wall brackets
2
Wall screw/plug set (5pcs)
2
Cross bars
1
Grounding screw
1
Rack screw/nut set, M6x12mm (10pcs)
Product Number
NTM 201 3605/1

Length
810 mm

Width
100 mm

Product Number
NTM 201 3607/1
Height
50 mm

Weight
4.3 kg

Rack frame 50U, Paint coated, Grey


19" Rack Frame can house RBS equipment such as power, batteries, transmission, MU for main remote, DF-OVP
connection modules etc.The 19" Rack System is applicable on other areas as well, due to flexibility and expandability. The 19" Rack Frame is floor mounted and secured to the wall.The wall distance mounted is 420mm and
height is 2221mm(50U).

Length
2235 mm

Width
100 mm

Height
100 mm

Weight
9.3 kg

19" Rack Flatpack 12U


This powder coated 19 flatpack solution is easily transported and mounted on to the wall. It has adjustable
mounting rails and its 19" vertical extrusion is movable. Side and back panels are removable. The front of the rack
is lockabel and made of hardened glass. It is supplied with key. Cable entry from top and bottom.
Maximum load rating: 60kg.
Interior Height: 635 mm / 12U
Interior Deapth: 450 mm
Interior Width: 600 mm

Weight
0.9 kg

Shield Anchor set for fastening RBS Installation Frame and cabinet. Fasten in concrete, hollow block wall, hollow
brick wall, solid brick and in hollow floor beams.
NTM 2012977/1, NTM2012977/2 and NTM2012977/3
Consist of:
Qty Description
4
M12 Shield anchor EN 20898-1
4
Washer

Product Number
NTM 201 2977/1
NTM 201 2977/2
NTM 201 2977/3
NTM 201 2977/4

Length
110 mm
90 mm
130 mm
110 mm

Width
110 mm
110 mm
110 mm
110 mm

Height
20 mm
20 mm
20 mm
20 mm

Weight
0.8 kg
0.8 kg
0.8 kg
1.2 kg

Bolt Set BBS 2000i, M10x60 mm


Bolt and washer for mounting the Power Cabinet BBS 2000i to the Base Frame.
Consist of:
Qty Description
4
Bolt, MC6S 10x60mm D ST 8.8 FZV4
4
Washer, BRB 22x11x2mm4
Length
80 mm

Width
30 mm

Height
20 mm

Weight
0.17 kg

Width
100 mm

Height
50 mm

Weight
0.86 kg

Material for supporting RBS cabinet to wall.

Length
660 mm

Width
620 mm

Height
230 mm

Weight
26.61 kg

Generic Base frame assembly supplied in kit

Length
570 mm

Consist of:
Qty Description
2
Angel Bracket
2
Screw, T6S NR 8x65
2
Pendant Rail
2
Washer, BRB 10.5x22x2
1
Screw Set
2
Screw, M6S M10x25 H
2
Plug, TP4
2
Washer, BRB 10.5x20x2
Product Number
NTM 201 2413/1

Length
300 mm

Anti-Tip Device for RBS 6201, 225 mm

Consist of:
Qty Description
1
Frame, SXK1091089/1
2
Cover plate, SXA1345271/1
3
Plate, SXK1091553/1
4
Plate, SXK1091554/1
5
Plate, SXK1091152/1
6
Grommet, SXA 215 0220/1
7
Screw, SBA116040/0140
8
Locking nut, SBM101116/03
9
Screw, SBA116040/0100
10 Installation kit, NTM2013985/1

42

Height
50 mm

Wall Support Kit for Indoor Cabinet

Generic Base Frame

Product Number
SXK 109 1049/1

Width
140 mm

Shield Anchor, Loose Bolt Set, M12

Product Number
NTM 201 3444/1

Consist of:
Qty Description
1
Top Panel
1
Hardened Glass Door
1
Key
2
Side Panel
1
Back Panel
2
Fixed Shelf & Rail
1
Bottom Panel
2
Frame Front/Back
1
Wall mount beam
16 Screw
4
Anchor Bolt
1
Captive Nut & Screw
Product Number
SDC 901 538/1

Length
600 mm

NTM 201 2977/4


Consist of:
Qty Description
6
Shield anchor EN 20898-1, M12x110mm
6
Washer, =27mm

Consist of:
Qty Description
2
Uprights 50U
1
Assembly screw/nut set, M6x12mm (20pcs)
4
Wall brackets
2
Wall screw/plug set (5pcs)
3
Cross bars
2
Grounding screw
2
Rack screw/nut set, M6x12mm(10pcs)
Product Number
NTM 201 3604/2

Consist of:
Qty Description
1
19" Mounting frame
5
Terminal block (10-pair) Slotted connections
1
Rack screw/nut set, M6x12mm (10pcs)

Use this kit as a wall support to secure one cabinet to the wall. Suitable for environment with corrosiveness class
C2 according to SS-EN ISO 12944-2.
Consist of:
Qty Description
2
Angle bracket
2
Plastic plug
2
Screw 8x65mm
2
Washer 10.5x22x2mm
2
Screw M10x25mm
2
Washer 10.5x20x2mm
Width
460 mm

Height
420 mm

Weight
12.91 kg

Product Number
NTM 201 4146/1

Length
225 mm

Width
75 mm

Height
50 mm

Weight
0.4 kg

43

Tools and instruments

Cabinets and frames

Feeder Tools

Cabinet and Frame Accessories


Anti-Tip Device for RBS 6201, 550 mm

Feeder Preparation Tools

The anti-tip device secure the RBS 6000 cabinets to the wall.Prevents cabinet to tip over during installation,maintenance and operation. The tightening straps is fixed to the wall and then fixed to the cabinet

Tool set for preparing the feeder cable before assembly with a connector. Note: Brand unique tools are not included in this kit.

Consist of:
Qty Description
2
Tightening strap, 500x25mm
2
Plastic plug
2
Screw 8x65
2
Washer 10.5x22x2
2
Screw M10x25mm
2
Washer 10.5x20x2

Consist of:
Qty Description
1
Tool Box
2
Slip joint pliers
1
File, flat
1
Hacksaw
10 Hacksaw spare blade
1
Brass and Fiber brush kit
1
Cable knife
1
Quick-Grip
2
Marking tape, Blue
2
Marking tape, White
2
Marking tape, Yellow
2
Marking tape, Red

Product Number
NTB 101 24/1

Length
200 mm

Width
130 mm

Height
40 mm

Weight
0.15 kg

Protection Cover Rear


Cover for protecting the rear of RBS 6301.

Product Number
LTT 601 160/1

Consist of:
Qty Description
1
Protection Cover Rear

Slotted Socket, 27/32 mm

Product Number
SXK 109 1183/1

Length
600 mm

Width
410 mm

Height
110 mm

Weight
1.764 kg

Length
515 mm

Width
390 mm

Height
120 mm

Weight
60.15 kg

Height
32 mm

Weight
0.14 kg

Used when connecting jumpers in the RBS cabinet.


Product Number
LSB 107 05/1

Length
75 mm

Width
27 mm

Optical Cable Boxes


Outdoor Fiber Connection Box
The box supports up to 8 RR heads 8 duplex SFF or 8 simplex LFF adapters and it is fitted with bend radius limiting mandrels. Suitable for mount on poles, walls or tower legs with round, L- and V-shape.
IP 66/67 EN 60529, NEMA 1,4,4X ,6, 12 and 13. 2 knock-out holes cable gland M16. 2 knock-out holes cable
gland M25. Operating temperature: -40 to +85.
Consist of:
Qty Description
1
Injection moulded box
3
LC duplex adapter,Single mode
4
Cable clamps
2
Cable gland 3-fold
1
Adapter plate 8SFF duplex
2
Cable gland single ( =10mm)
2
Pole mounting bracket
4
Cable gland blindplug
1
Cover with integrated screws
1
Mounting nut
2
Quick hose clamps 60-500mm
Product Number
NCD 901 37/1

Length
75 mm

Spanner for Angle Connectors 7/16, 32 mm


Use this hand tool to tighten 7/8". DIN 7/16 connectors in the Feeder system where the connector has a 90 angle
and where the space is limited. Stainless Steel, SS2377.
Product Number
LSB 107 30/1

Length
75 mm

Width
55 mm

Height
45 mm

Weight
0.07 kg

Height
340 mm

Weight
23 kg

Antenna System Installation Equipment


Product Number
LTT 601 142/1
Width
180 mm

Height
255 mm

Length
820 mm

Width
375 mm

Weight
1 kg

Feeder Jack Stand


The feeder jack stand to be used when winding off feeder cables from a cable drum, capacity up to 5 tons.

Power Cable Boxes


DC Power Junction Box
The DC Power Junction box connects two Main-Remote power cables at Telecom site. It is supplied with a 2m
pre-assemblied 2 x10 mm power cable for quick connection against RRU or AIR. The aluminum junction box is
water resistant according to IP54/55 and it seals/connects one power cable with cross-section up to 25mm and
sheath diameter =8.5-26 mm.

Consist of:
Qty Description
2
Stand, 5 tons hydraulic jack for handling heavy cable drums
1
Tubular axle, L=2 m
2
Stop collar
Product Number
LTT 601 97/2

Length
2000 mm

Width
650 mm

Height
300 mm

Weight
39 kg

Consist of:
Qty Description
1
Junction Box, Powder coated Cast Aluminum, IP55/54
1
Terminal Block =1.5-25mm (Stranded cable), UL-rated 70 A
1
Power Cable 2m, 2x10 mm, TFL 492 325, Black, UV-stabilized, Halogen-free
2
House Clamp = 40-150 mm, stainless steel
1
Cable Gland M25/M30, IP55/54, =8.5-26 mm
1
Cable Gland M20, IP55/54, =6-12 mm
1
Cable Gland Adapter
Product Number
NTB 101 75/1

44

Length
200 mm

Width
100 mm

Height
100 mm

Weight
0.8 kg

45

Tools and instruments

Tools and instruments

Electrical Power Tools

Torque Wrenches

Hammer Drill Machine, 230 V AC

Torque Wrench, 0.5-4.0 Nm

The hammer drill machine drills through, plastics, wood, plaster or even through concrete during the construction
work at the RBS site.

The Torque Wrench kit is suitable to tighten connectors, bolts and screws with the torque range 0.4 - 4.0 Nm.

Consist of:
Qty Description
1
Tool box
1
Hammer drill machine 230V AC
2
Hammer Drill 5,5mm L=120mm, (60mm*)
2
Hammer Drill 6mm L=120mm, (60mm*)
2
Hammer Drill 8mm L=160mm(100mm*)
2
Hammer Drill 10mm L=160mm(100mm*)
2
Hammer Drill 12mm L=160mm(100mm*)
2
Hammer Drill 20mm L=200mm(150mm*)
1
Chuck holder
1
Chuck 2 - 13mm
1
Key
* Max. drilling depth
Product Number
LTT 601 146/1

Length
450 mm

Product Number
LTT 601 145/1

Height
190 mm

Weight
8.5 kg

The hammer drill machine drills through, plastics, wood, plaster or even through concrete during the construction
work at the RBS site. This cordless hammer drill is delivered with one extra battery.
Consist of:
Qty Description
1
Hammer drill machine
1
Extra Battery, 3.0Ah
2
Hammer drill 5.5mm L=120mm, (60mm*)
2
Hammer drill 6mm L=120mm, (60mm*)
2
Hammer drill 8 mm L=160mm, (100mm*)
2
Hammer drill 10 mm L=160mm, (100mm*)
2
Hammer drill 12mm L=160mm, (100mm*)
2
Hammer drill 20mm L= 200mm, (150mm*)
1
Charger, 230V, AC
1
Chuck 2-13 mm
1
Chuck Holder
1
Key
1
Maintenance set
1
Tool Box
* Max. drilling depth
Length
500 mm

Height
40 mm

Weight
0.7 kg

Consist of:
Qty Description
1
Torque wrench, 5-25 Nm
1
Bits head 1/4" bits
1
Socket adaptor 1/4" to 3/8"
1
Socket head 1/4" - 13 mm
Length
310 mm

Width
75 mm

Height
65 mm

Weight
0.8 kg

Torque Wrench, 20-100 Nm (Basic)


The torque wrench fixes equipment with the torque range 20-100 Nm. Easy to handle during to the installation
work of the RBS site.

Width
140 mm

Height
390 mm

Weight
10.9 kg

For common use when screwing and drilling. This cordless screwdriver is delivered with one extra battery.
Consist of:
Qty Description
1
Screwdriver machine cordless 14,4 V DC
1
Extra Battery, 2.8 Ah
1
Charger, 230V, AC
1
Drill set, D=1.5mm - 6.5mm
Length
420 mm

Width
100 mm

The tool set is suitable for installations at RBS sites. The torque driver fixes equipment with the torque range 525Nm.

Product Number
LTT 601 140/1

Screwdriver Machine, 14,4 V DC

Product Number
LTT 129 09/2

Length
250 mm

Torque Wrench, 5-25 Nm


Width
250 mm

Hammer Drill Machine, Cordless, 36 V DC

Product Number
LTT 601 147/1

Consist of:
Qty Description
1
Torque-driver, 0.5 - 4 Nm
1
Bits Torx, T8 x 50 mm
1
Bits Torx, T25 x 50 mm
1
Socket set, 7 Sockets and 1 Socket adapter Bits to 1/4", L=50 mm 4.0, 4.5, 5.0, 5.5, 6.0, 7.0 and 8.0 mm
1
U-key, 8 mm for SMA-connector
1
U-key, 14 mm for TNC-connector
1
U-key, 18 mm for N-connector

Consist of:
Qty Description
1
Torque wrench, 20 - 100 Nm
1
Ratchet head, 3/8"
1
Socket adaptor, 3/8" to 1/2"
1
Socket, 24 mm
1
Socket, 16 mm
1
Socket, 19 mm
1
Extension bar
Product Number
LTT 601 141/1

Length
470 mm

Width
170 mm

Height
60 mm

Weight
2.7 kg

Open Jaw Wrench


For tightening with socket tools, e.g. extension bar and ratchet handle. For Torque wrench LTT 601 141/1. 3/8".

Width
340 mm

Height
100 mm

Weight
5.1 kg

Cordless Screwdriver 3.6VDC


Cordless Screwdriver with 2 speed gear box, motor brake and integrated LED light. Use the Screwdriver at the telecom site during installation, construction and assembly of equipment. For example tightening the Doubel stack
Feeder clamp with Socket wrench kit LSB10733/1. or mounting the Cable ladder kits and Rack frame kits NTM
2013604/2, Slimline soft grip handle. Forward/reverse screw operation

Product Number
LSB 107 12/1
LSB 107 12/2
LSB 107 12/3
LSB 107 12/4
LSB 107 12/5
LSB 107 12/6
LSB 107 12/7
LSB 107 12/8

Length
13 mm
19 mm
24 mm
27 mm
32 mm
16 mm
17 mm
60 mm

Width
35 mm
45 mm
55 mm
60 mm
70 mm
45 mm
45 mm
40 mm

Height
35 mm
35 mm
35 mm
35 mm
35 mm
35 mm
35 mm
35 mm

Weight
0.122 kg
0.164 kg
0.215 kg
0.239 kg
0.239 kg
0.160 kg
0.160 kg
0.135 kg

Size
13 mm
19 mm
24 mm
27 mm
32 mm
16 mm
17 mm
15 mm

Mechanical/Electrical data:
Torque soft screw driving: 5 Nm
Torque hard screw driving: 10 Nm
Rated speed Low/High 150/0-580 rpm
Lockable universal bit holder
Battery charging time: 1 hour
Consist of:
Qty Description
1
Cordless Screwdriver 3.6VDC
1
Extra battery, Li-Ion 3.6V/1.3 Ah
1
Battery Charger 230VAC/3.6VDC
1
Hard Casing
Product Number
LSF 901 03/1

46

Length
175 mm

Width
210 mm

Height
135 mm

Weight
1.75 kg

47

Tools and instruments

Tools and instruments

Crimping tools

Tool Kits
Mechanical Press Tool 60 kN

Tool Set for RBS 6000

Mechanical Press tool with 60 kN press power for Cu connections. Use it to crimp cable lugs and C-clamps in the
grounding and lightning system of the radio base station (RBS). If the tool is used correctly with
Ericsson supplied C-clamps, Cable Lugs or Jointing Sleeves an electrical connection according to SEN 24510 or
BS 4579: 1 is achieved.

The personal tool set is specially designed for site installation and relevant to all types of RBS 6000 cabinets.

Consist of:
Qty Description
1
Crimping Tool Mechanical 10-95mm for CU, 16-25mm for stranded AL,1and 35mm for solid AL.
C-clamps up to 50mm
1
Press Die TB 9-13 for conductor area 16mm and 35mm
1
Press Die TB 11-C89 for conductor area 25mm and C-clamp C89
1
Pres Die TB 14.5-17 for conductor area 50mm and 70mm
Product Number
LTT 601 89

Length
460 mm

Width
190 mm

Height
60 mm

Weight
4.3 kg

Hydraulic Press Tool 60 kN


Press tool for Cu connections. Use it to crimp cable lugs and C-clamps in the grounding and lightning system of
the radio base station (RBS). If the tool is used correctly with Ericsson supplied C-clamps, Cable Lugs or jointing
sleeves an electrical connection according to SEN 24510 or BS 4579: 1 is achieved.
Consist of:
Qty Description
1
Crimping Tool Hydraulic, 10-150mm for CU, 16-25mm2 for stranded AL, and 35mm for solid AL.
C-clamps up to 50mm .
1
Press Die for C-clamp C4, C8, C9 and C89
1
Press Die TB 8-17 for conductor area 10mm and 70mm
1
Press Die TB 11-14.5 for conductor area 25mm and 50mm
1
Press Die TB 9-13 for conductor area 16mm and 35mm
1
Press Die TB 7-20 for conductor area 10mm and 95mm
1
Press Die KB25 for conductor area 150mm
Product Number
LTT 601 86

Length
550 mm

Width
200 mm

Height
45 mm

Weight
5.6 kg

Coaxial Connectors, 50 and 70 ohm


This flexible hand tool connects BNC and TNC connectors to coaxial cable.
Consist of:
Qty Description
1
Crimping tool
1
Press die, red, size 1/2A
1
Allen key
1
Press die, yellow, size 2C
1
Press die, orange, size 2B
1
Press die, no colour, size >1/2A
1
Press die, violet, size 3D
Product Number
LTT 601 87

Length
174 mm

Width
180 mm

Height
55 mm

Weight
1.5 kg

Consist of:
Qty Description
1 pc Tool case
1 pc Ball-shaped head bits 8
1set Ratchet ring spanners 8-19 mm
1 pc First aid kit
1 pc Screwdriver Torx T5
1 pc Multimeter
1 pc Static control wrist strap
1 pc Screwdriver Torx T8
1 pc Box spanner 5,0x60, (L=150 mm)
1 pc Ear muffs
1 pc Screwdriver Torx T10
1 pc Picking pliers, Stirex
1 pc Protective eyewear
1 pc Screwdriver Torx T15
1 pc Head torch, LED H5
2 pair Gloves
1 pc Screwdriver Torx T20
1 pc U-wrench Al 25 mm
1 pc Cable cutter < 95 mm2
1 pc Screwdriver Torx T25
1 pc U-wrench Al 28 mm
1 pc Side cutting pliers, 8160
1 pc Screwdriver Torx T30
1 pc Screwdriver for Bits, magnetic
1 pc Slip joint pliers
1 pc Screwdriver Torx T40
1 pc Socket 3/8-16 mm
1 pc Knife
1 pc Screwdriver slot head 2,5x50
1 pc Socket 3/8-18 mm
1 pc Hammer
1 pc Screwdriver PZ 2, 125 mm
1 set of bits 31-parts
1 pc Spirit level, magnetic
1 pc U-wrench 21-23 mm
1 pc Adaptor for bits
1 pc Hack saw
1 pc U-wrench 24-27 mm
1 pc Torx bit TT30x75 mm, magnetic
1 pc Saw blade (10 pcs)
1 pc Swivel socket wrench 6-7 mm
1 pc Socket set 3/8, 10-19 mm
1 pc Extension bar 3/8, 250 mm
1 pc Measuring tape, 5 m
1 set Set of U-wrench, 8 pcs (6-22 mm)
Product Number
LTT 601 135/1

Length
230 mm

Width
500 mm

Height
400 mm

Weight
13.4 kg

Tool Set for PCM Cable, 75 ohms


Crimping tol set for PCM cables, consists of LTT 601 108 and LTT 601 16.
Consist of:
Qty Description
1
Crimping, PCM Cable, 75
1
Crimping, PCM Cable, 75
Product Number
NTM 201 291

48

, inner conductor
, outer conductor
Length
480 mm

Width
170 mm

Height
50 mm

Weight
1.6 kg

49

Tools and instruments

Tools and instruments

Tool Kits

Safety Equipment
Quality Audit Tool Kit

Tower Work Set

Slim Back-pack filled with tools for quality audit of Telecom site. Inspect the RBS, Transmission, Power, Switching
and grounding installation with the tools in this kit. Selected tools of high quality for the professional quality audit
inspector. Swedish sturdy back-pack developed for motion in harsh winter conditions and humid climate. Note:
Bring Torque wrench set LTT 601 141/1 to audits in earthquake zones (check the bolts of RBS).

This work set is intended for work in tower, mast and poles.

- ROHS approved tools


- Slim design 38L, easy to climb with.
- PFOS/PFOA-free durable fabric that repels water
Consist of:
Qty Description
1
Back pack tight XL 38L
1
ESD Wrist-Strap
1
Torque wrench, Range 5-25 Nm
1
Binocular 8x21
1
Pocket lamp, LED H5
1
First-aid kit
1
Compass, 3 different magn. Zones MN, ME and MS.
1
Adjustable spanner
1
Spirit level, magnetic
1
Side cutting plier
1
Screw driver, 1x5,5x125mm
1
Electro tape L=20m, Black
1
Measuring tape, L-3m
1
Tape, self-fusing, 9m
1
Bit set
1
Bit holder,
1
Socket 10mm
1
Socket 13mm
1
Adaptor 3/8-1/4
1
Socket adaptor - 13mm
1
Extension bar 100mm
1
Battery Ventilation Test Tool
Product Number
LTT 601 150

Length
600 mm

Width
200 mm

Product Number
LYA 175 115/1

Length
570 mm

Width
350 mm

Height
250 mm

Weight
5.6 kg

Work Line Set


This work line set is used for work in tower, mast, poles, roof and wall.
Consist of:
Qty Description
1
Helmet
1
Tool/bolt bag
1
Protection goggles
1
Fall arrester device and energy absorber
2
Support line, white
1
Pressure bandage
2
Protection gloves pair, inner size L
2
Protection gloves pair, outer size L
2
Protection gloves pair, outer size XL
2
Protection gloves pair, inner size XL
1
Bag, 27L
Height
150 mm

Weight
1.6 kg

Product Number
LYA 175 117/1

Length
300 mm

Width
300 mm

Height
530 mm

Weight
11.5 kg

Safety Line Set

Special Tool Kit


This kit contains special tools for Ericsson RBS cabinets, designed to make it easier to install and maintain RBSs
and avoid damaging parts.

This Safety Line Set is used as fall protection when permanent fall protection equipment is missing in the towwer,
mast and roof.

Consist of:
Qty Description
1
Extractor tool EMILY Shield
1
Extractor tool for IDM Connector
1
Slotted Socket 27/32mm
1
Extractor Tool for QMA Connector
1
Wrist strap Kit
1
Power Cable Tool
1
RU-Extract Handle button
1
Instruction
1
Spanner for angle connector 7/8", 32mm
1
Termination Tool, Krone

Consist of:
Qty Description
1
Bag, volume 40L, orange
1
Core-mantle rope100 m
1
Fall arrester device
1
Carabiner, big
1
Lifting sling 1.5m

Product Number
LTT 601 151/1

Length
240 mm

Product Number
LYA 175 118/1

Width
310 mm

Height
50 mm

Weight
0.98 kg

Safety Equipment
Full Body Harness, Size S - XL
The full Body Harnesses is used to secure the worker during installation and maintenance on high altitude e.g.
upon radio towers and roofs. The body harness is equipped with fixed D-ring to avoid neck damage by fall.
LYB 921 53/1 S, M
LYB 921 53/2 L, XL
Product Number
LYB 921 53/1
LYB 921 53/2

50

Consist of:
Qty Description
1
Helmet
1
Tool/bolt bag
1
Protection goggles
1
Fall arrester device and energy absorber
2
Support line, white
1
Pressure bandage
2
Protection gloves pair, inner size L
2
Protection gloves pair, outer size L
2
Protection gloves pair, outer size XL
2
Protection gloves pair, inner size XL
1
Bag, 27L

Length
350 mm
350 mm

Width
280 mm
280 mm

Height
140 mm
140 mm

Weight
1.6 kg
1.7 kg

Length
570 mm

Width
350 mm

Height
250 mm

Weight
9 kg

Width
300 mm

Height
500 mm

Weight
10.3 kg

Rescue Line Set


This kit is a rescue and evacuation set.
Consist of:
Qty
Description
100m
Antipodes rope, Red, 11.5mm
2
Shrinking Tube
1
Express 25cm
1
Grillonrope,3m
1
Lifting sling, 80cm
1
AMD Triact Autolock
1
ID 10-11,5mm
1
Mini Traxion
1
Ball lock
1
G.O. No.7 carabiner
2
AMD Tract Autolock
2
Block,Mini
1
Rope Bag,Red
Product Number
LYA 175 119/1

Length
300 mm

51

Tools and instruments

Tools and instruments

Safety Equipment

Test Instruments

Step Ladder, Combiflex 3.6 m

Multimeter

A Heavy Duty Multifold Ladder for your installation at RBS Site. The ladder can be folded into 9 different positions
for example straight 3.6 m, Angle 1.8m, trestle, or frame position. Type approval from SP Technical Research Institute of Sweden SPCR 064 102102. Domestic rated weight: 150 Kg. The end of the ladder has anti-skid protection. After the installation the ladder is easily folded into a small package.
Folded it can be transported in an elevator or in a car boot. Ladder is supplied with anti-tilt support.

Instrument for measurement of Voltage, Current and Resistance.

Consist of:
Qty Description
1
Multifold Ladder 3.6m
1
Anti-tilt Support
Product Number
LYA 175 122/1

Length
1000 mm

Width
360 mm

Height
260 mm

Weight
11 kg

Product Number
LPK 102 024/3

Length
185 mm

Width
90 mm

Height
43 mm

Weight
0.42 kg

Antenna Tester Set, Bird Site Analyzer


Frequency Range: 25 MHz to 6 GHz. Rejects "On-Frequency" interference up to +13 dBm. Maximum Input: +22
dBm. PC software allows download to PC to analyze data for long-term assessment of system trends, problems,
and performance. Trace overlays to track performance over time. Saves 15 Calibrated Setups. Stores 500 traces
at 238 pts of resolution. Alphanumeric labeling of saved traces. Color display is viewable in direct sunlight.

Special Tools
Cable Tie Tensioner
Tensioning BAND-IT Ties (steel) and Multi-Look.
Product Number
LSD 901 52/1

Length
240 mm

Width
75 mm

Height
50 mm

Weight
0.39 kg

Plate Shears
Tool suitable for cutting mild steel sheet up to thickness 1,5 mm. Straight cutting edge with slight toothing. Jaw
lenght 32 mm and with ergonomic grip.
Consist of:
Qty Description
1
Snips
Product Number
LDK 3016

Length
250 mm

Width
90 mm

Height
40 mm

Weight
0.451 kg

Long Socket Wrench 10+13 mm


The long Socket wrench is used together with the cordless screwdriver LSF 901 03/1 or LTT 129 09/2.
The Long Socket wrench tighten M6/M8 (10mm/13 mm) nuts of the doubel stack Feeder Clamp.
Consist of:
Qty Description
1
10mm/M6 Socket wrench, Lenght 150 mm
1
13mm/M8 Socket wrench, Lenght 170 mm
Product Number
LSB 107 33/1

Length
210 mm

Width
150 mm

Height
18 mm

Weight
0.151 kg

Carrying Bag
High tensile strenght carrying bag with sturdy bottom end. Multi purpose bag that can even carry RBS 2206,3202.
Size: 1900x480x630 mm. Volume: 574 litre
Tensile Strenght Lenghtwise: 2500 N
Tensile Strenght Crosswise: 2400 N
Tear Strength Lenghtwise: 400 N
Tear Strenght Crosswise: 400 N
Consist of:
Qty Description
1
Bag
2
Fastener
2
Belt Lock
1
Bottom plate 450x600
Product Number
LYA 175 104/3

52

Consist of:
Qty Description
1
Instrument
1
Test Leads
1
Instruction Sheet
1
Soft Case

Consist of:
Qty Description
1
Calibration unit 7/16, open, short, load
1
Cord Europe
1
Site Analyzer 25-6000MHz
1
Test cable (Nm-Nm)
1
Calibration certificate
1
Case
1
AC-charger
1
Precision Load
1
CD- software
1
Adapter (Nf-Nf)
1
Instruction Manual
1
Adapter 7/16female-7/16female
1
Cable 9 pin
1
Adapter N female-7/16 male
1
Automotive power adapter
1
Adapter N female-7/16 female
Product Number
LPK 102 101/9

Length
460 mm

Width
530 mm

Height
220 mm

Weight
11 kg

Battery Ventilation Test Tool


Battery ventilation test tool that checks if there is leakage in the exhaustion hose from the batteries. With this kit
the installer can perform a test that detects if the battery back-up system will leak explosive oxy-hydrogen or hydrogen gas.
Consist of:
Qty Description
1
Pressure gauge with pump and hose
1
Instruction
1
Extra hose,100 mm
2
Nipple
1
Soft Case
Product Number
LTP 177 200/1

Length
160 mm

Width
110 mm

Height
50 mm

Weight
0.25 kg

Tools for Optical Fiber


Fiber Check Tool

Length
750 mm

Width
510 mm

Height
160 mm

Weight
9.954 kg

The Fiber check tool is an simple way of verifying that the OIL cable is ok, and that its not been damaged e.g. during installation. The pen is held in one end of the OIL cable and if the cable is ok a red light from the laser pen is
visible in the other end. If no light is visible then is either the cable end dirty, and have to be cleaned, or the cable
is damaged, and have to be replaced. The pen can be set to either have flashing or continuous light. It comes in a
box with two AAA-batteries included.
Product Number
LPB 112 102/1

Length
175 mm

Width
70 mm

Height
22 mm

Weight
0.11 kg

53

Tools and instruments

Accessories

Tools for Optical Fiber

Marking

Ferrule End-Face Cleaner

Generic Marking Kit

The cleaning tool can be used in the field or in the factory to effectively clean ferrules within adapters and cable
assemblies and restore the fiber optic connectors preformance. It has a polyester static free cloth for optimal cleaning. Includes 350 swipes per cleaner (1 swipe per cleaning).
The cleaning tip is adjustable to 45 degrees for angled adapters and the tip is spring-loaded for controlled cleaning pressure. The cleaning tool is applicable for PC and APC type ferrules and ideal for cleaning transciver ports.

Identify and separate your indoor equipment, cable or fiber with this label kit.
It marks 100 cables with a maximum diameter of 47,5 mm.

Product Number
LTT 601 154/1

Length
280 mm

Width
60 mm

Height
27 mm

Weight
0.11 kg

Product Number
NTM 201 3887/1

OTDR Instrument
A kit solution for FTTX drop cables and MDU cables that reduces costly re-visits at site. Features: OTDR measurement up to 10 km ( l = 1550 nm) with supplied components. Optical power meter (-5 to -45dBm, Accuracy +/-0.5
dB, Max input +10dBm). Palm Size (7,5"x3,8"x1,9" / 190x96x18 mm). IP 51, sealed design. Clear "Pass"/ "Fail"
presentation of measurements on display.
Consist of:
Qty Consist
1
Network master
1
Drop cable, fault locator module
1
Power meter, 1550nm single mode, UPC
1
SC Connector
1
LC replacement Adaptor
1
Soft Case
Product Number
LPK 102 111/1

Length
190 mm

Height
45 mm

Weight
0.8 kg

Ru-extractor Handle
Tool used for removing ESD-sensitive printed board assembly from the cabinet.
Length
100 mm

Width
100 mm

Height
20 mm

Weight
0.03 kg

Wrist Strap Kit, ESD protection


Wrist strap to connect user with ground during work with ESD sensitive equipment.
Product Number
LTT 601 136/1

Length
100 mm

Length
100 mm

Width
100 mm

Height
30 mm

Weight
0.25 kg

Handheld Labelprinter
Handheld Labelprinter with LCD screen, numeric pad and manual cutter. Prints on TZ adhesive laminated tapes
with the height 3.5mm, 6mm, 9mm or 12 mm. Create time, date labels or flag labels for equipment, cable or racks.
ABC Keyboard with numeric characters.
Many symbols, incl. electrical
8 fonts with 5 sizes
Vertical and mirror-inverted print out
5 types of frames
2 rows to write on
9 millimeters max print height
More labels available: SVB 153 215/1

Width
96 mm

DDF Tools
Product Number
LTD 901 43/1

Consist of:
Qty Description
100 Marking plates (90x19mm)
200 Cable tie lenght 150 mm)
1
Marking pen

Width
100 mm

Height
30 mm

Weight
0.04 kg

Consist of:
Qty Description
1
Handheld Labelprinter
1
Case
1
230VAC Adapter
1
Operating instructions
1
Adhesive Tape 12 mm x 8m, Black text/Yellow background
Product Number
LSY 901 81/1

Length
203 mm

Width
107 mm

Height
57 mm

Weight
0.37 kg

Laminated Adhesive Tape


Laminated adhesive tape for marking. Resistant to water, sunlight, chemicals, heat and cold. Label with Black
print/White background that sticks to virtually any surface. It stays on through hot and cold environments. Use this
label together with Handheld Label Printer LSY 901 81/1
Consist of:
Qty Description
1
Adhesive laminated Tape 8m x 12 mm
Product Number
SVB 153 215/1

Length
100 mm

Width
70 mm

Height
20 mm

Weight
0.046 kg

Tape L/H
8 m/12 mm

Electro Tape Bulk Kits 10 pcs


These electro tape bulk kits mark OIL cables, feeder or power cable during installation. Secondary usage as mechanical protecion or electric isolation. Tape has excellent durability against abrasion, moisture, Acids and UVlight. High dielectric strength 9000 V and excellent mechanically protection. Lowest application temperature: -10
Deg. C. Comply to ASDM D-1000. CE -marked.
Consist of:
Qty Description
10 Electro tape 20mx0,2x19mm
Product Number
MPP 901 146/1
MPP 901 146/2
MPP 901 146/3
MPP 901 146/4

54

Length
70 mm
70 mm
70 mm
70 mm

Width
19 mm
19 mm
19 mm
19 mm

Tape Thickness
0.2 mm
0.2 mm
0.2 mm
0.2 mm

Colour
Blue
Red
White
Yellow

55

Accessories

Accessories

Marking

Miscellaneous Accessories
Labelset WCDMA, RRU

Common Installation Material

Marking of optical fibre cables and power cables for WCDMA (RRU) systems.

The Common Installation materiel is consumable supplies for indoor installations. For example, inside the radio
base station room you can fasten the feeder cable to a cable ladder if you use the cable clamp.
Tie straps for strapping grounding cable, transmission cable, alarm cable etc. to cable ladders or cable profile.
Electro tape of different colours to mark feeder sectors. By that way avoiding mixing up Tx/Rx branch during installation. Label holders for permanent marking of feeder by that way avoiding mixing up co-sited operators
equipment.

Consist of:
Qty Description
1
Label sheet (Sector 1)
1
Label sheet (Sector 2)
1
Label sheet (Sector 3)
1
Label sheet (Sector 4)
1
Label sheet (Sector 5)
1
Label sheet (Sector 6)
1
Label sheet (Power)
1
Label sheet (OIL)
1
Label sheet (A)
1
Label sheet (B)
Product Number
NTM 201 3767/1

Length
170 mm

Width
120 mm

Height
5 mm

Weight
0.04 kg

Labelset GSM, RRU


Marking of optical fibre cables and power cables for GSM (RRU) systems.
Consist of:
Qty Description
1
Label sheet (Cell A)
1
Label sheet (Cell B)
1
Label sheet (Cell C)
1
Label sheet (DX1)
1
Label sheet (DX2)
1
Label sheet (Power)
1
Label sheet (OIL)
Product Number
NTM 201 3767/2

Product Number
7/N TM2 01201

Length
170 mm

Width
120 mm

Height
5 mm

Weight
0.02 kg

Height
4 mm

Weight
0.1 kg

Label blocks packed in a plastic bag marked NTM 201 207/1


Consist of:
Qty Description
1
Label sheet (Cell A: )2Label sheet (TX1)
1
Label sheet (Cell B: )2Label sheet (TX2)
1
Label sheet (Cell C: )2Label sheet (TX3)
1
Label sheet (Cell O: )2Label sheet (RXA)
1
Label sheet (DX1)1Label sheet (RXB)
1
Label sheet (DX2)
Length
100 mm

Width
100 mm

LTE Marking
Marking of sectors and equipment in LTE system.
Consist of:
Qty Description
1
Label sheet (Sector 1: )
1
Label sheet (Sector 2: )
1
Label sheet (Sector 3: )
1
Label sheet (Sector 4: )
1
Label sheet (Sector 5: )
1
Label sheet (Sector 6: )
1
Label sheet (A: )
1
Label sheet (B: )
1
Label sheet (C: )
1
Label sheet (D: )
Product Number
NTM 201 2964/1

Length
410 mm

Width
320 mm

Height
105 mm

Weight
2.87 kg

Additional Fastening Material

Feeder System Marking for GSM

Product Number
NTM 201 207/1

Consist of:
Qty Description
2
Tie Strap, 366x4.7 Black, 100 pcs
1
Screw, 100 pcs, TST 8x1 PH2
1
Wall Plug, Red, 100 pcs
1
Electro tape, White
1
Tie Strap,141x3.6 Natural, 100 pcs
1
Electro tape, Red
1
Tie Strap,290x3.6, 100 pcs
1
Electro tape, Blue
2
Tie Strap,112x2.4, 100 pcs
1
Electro tape, Black
1
Cable Clip,10-14mm, 100 pcs
1
Label Holder, 100 pcs
1
Screw, 100 pcs, TST 8x3/4 PH2

A complete set of mounting/fastening material for the RBS site. Expander screws, screws and plugs for fastening
equipment no matter the type of wall. Possible to mount against brick, wood, concrete or plaster partion wall.
Cable ties for strapping grounding, power, feeder cable to cable profiles and cable ladders.
Pliers/punch bend for potential equalisation of metal objects in the site.
Consist of:
Qty Description
1
Cable clip TC 7-10mm l=25mm, white, 100 pcs
1
Cable clip TC 10-14mm l=30mm, white, 100 pcs
2
Tie strap w=3.6mm l=141mm, natural, 100 pcs
2
Tie strap w=4.7mm l=366mm, black, 100 pcs
1
Fixing band TUB 12, 10m
1
Hammer screw fixing 5x50, 100 pcs
1
Spring toggle cavity fixing 13xM5S, 25pcs
25 Self drill cavity fixing
1
Screw plug fixing 6x35, 25 pcs
1
Screw anchor cavity fixing TMX-6D, 50pcs1
1
Screw anchor cavity fixing TMX-6E, 50 pcs
1
Pliers/Punch-bend
1
Tie strap 10x0.5mm, L=10m
2
Set of materials: screw M8x16, nut, clamp, 10 pcs
1
Tie strap support, 100 pcs
1
Set of materials: screw M5x12, elastic washer, nut, 50 pcs
1
Set of materials: screw M5x25, elastic washer, nut, 50 pcs
1
Potential grounding kit
2
Shield anchor set, 110mm
2
Shield anchor set, 90mm
1
Compartment box
Product Number
NTM 201 1491/1

Length
540 mm

Width
430 mm

Height
130 mm

Weight
13 kg

Width
90 mm

Height
30 mm

Weight
0.15 kg

Screw and Plug Set


Used for fasten equipment to walls.

Length
135 mm

Width
130 mm

Height
10 mm

Weight
0.05 kg

Consist of:
Qty Description
5
Screw, T6S 8X65 ST FZV
5
Wall Plug, Green
5
Washer, BRB 10.5X22X2 ST FZB
Product Number
NTM 201 257

Length
120 mm

Cable tie, Stainless Steel Band (Plastic coated)


Flexible tape-shaped tie strap with a disconnected locking device at one end. Use this tie strap to bundle together
or fasten cables, lines or components.
Product Number
SET 145 064/230
SET 145 064/305
SET 145 095/457

56

Length
230 mm
305 mm
457 mm

Width
6.4 mm
6.4 mm
9.5 mm

Height
1.1 mm
1.1 mm
1.1 mm

Weight
0.007 kg
0.008 kg
0.018 kg

57

Accessories

Power Back-up

Miscellaneous Accessories

Battery Sets

Outdoor Cable Tie, Bulk pack 100 pcs


The unique design of this Cable Tie with locking device allows an easy and fast installation. Installation is considerably quicker by putting the band in the locking head and at the same time tighten. The Cable Tie can be locked
temporarily and later unlocked for complementary addition of cabels, before permanent locking. Further it is easier
to install with gloves at inaccessible spots. Temperature Range: -40 to +85C continously, (+105C in 500 hours).
Inflammability class: UL94 V2. Fulfill requirements: US MIL spec. 23190/3367. Approved by : UL according to reference E 6493.
Consist of:
Qty
Description
100 Halogen-free Black Cabel Tie 4,7x290 mm
Product Number
SET 133 066/1

Length
300 mm

Width
140 mm

Height
20 mm

Weight
0.21 kg

Max Bundle
75 mm

Screw and Plug Bulk Kits


Screw and plug kit for mount in concrete, brick or wood constructions. It fastens the round base (45 or 85 mm)
standoff for leaking feeder. Screw is type approved by Sitac for C4 environment (SS-EN ISO 12944-2). Outdoors:
Atmosphere with moderat amount of salt or apparent amounts of air pollution. Industry and Costal areas. Indoors:
Rooms with high humidity and large amount of pollutant from production processes such as chemical industry,
shipyards and swimming baths.
Consist of:
Qty
Description
100 Screw 4.5x45mm or 4.5x90mm, PH2
100 Double expanding Halogen-free Plug 5.5x35mm
Product Number
SXK 107 2856/1
SXK 107 2856/2

Length
175 mm
175 mm

Width
200 mm
200 mm

Height
150 mm
150 mm

Weight
0.84 kg
0.55 kg

The Hose Clamp can be installed on cable ladders, brackets, i-beams, and tubes. The clamps has a large clamping
range which makes them very versatile. All components are made of stainless steel.
Quick release worm drive clamps are easy to install and remove due to the swivel action locking of the screw.
To be used especially to fix RRU and RBS toa tube.
Consist of:
Qty
Description
1
Hose Clamp
Length
290 mm
290 mm
290 mm

Width
230 mm
230 mm
230 mm

Battery Sets
Battery Unit 19 48V/12Ah
This Battery Unit (BU) is backup for the RBS 6000 series. The BU has a temperature sensor that is placed on the
most temperature critical spot inside the BU. The BU has a gas collecting system that connects all four battery
blocks to common tubing for a secure transportation of hydrogen away from the battery. It is designed according
to EN 60 950-1 and it fulfills IEC 60 950-1, ANSI / UL 60950-1. The BU consists of 4 pieces, 12V 12Ah lead acid
battery blocks of AGM type and is supplied with battery box with pre-installed tubing. It is prepared with additional power connections to allow several units in parallel. IP class 21. Connectors: 2x175A power gloves. 1x2 pole
Connector. Hosing for gas collecting tubes
Consist of:
Qty Description
1
Battery box
4
Battery 12V,12Ah
Product Number
BKB 902 57/3

Length
660 mm

Width
510 mm

Height
290 mm

Weight
32.5 kg

Battery Blocks SBS

Hose Clamp

Product Number
SET 133 069/1
SET 133 069/2
SET 133 069/3

SBS EON Batteries


Long-life designed batteries. Suitable for telecom power back-up installations in harsh environments and unstable AC power supply
conditions. The SBS battery technology offers fast recharge time and leading energy density footprint.

Height
20 mm
20 mm
20 mm

Weight
0.07 kg
0.09 kg
0.15 kg

Install Dimension
40-150 mm
140-300 mm
250-500 mm

12V/100Ah lead acid Batteries of type SBS. Valve regulated with six cells in one monobloc.
Fits 19" and 23" Racks.
Use these batteries in telecom applications as the Power back-up system.
Containers and lids are UL94 V-0 rated flame retardant material and highly resistant to shock and vibration.
Approved as non-spillable cargo for ground, sea and air transportation in accordance with US DOT Regulation 49
and ICAO & IATA Packing Instruction 806.
Compliant with IEC 60896/21 and IEC 60896/22
Classified as "Long Life" according to Eurobat guide 1999
Conforms to Telcordia SR-4228
Recognised by UL (UL Standard 1989)
Consist of:
Qty Description
1
Battery block SBS 12V
Product Number
6/BKC 901 06/0101
6/BKC 901 06/0190

Length
395 mm
561 mm

Width
290 mm
125 mm

Height
100 mm
316 mm

Weight
32.6 kg
60 kg

Voltage
12 V
12 V

Type
SBS100
SBS190F

Battery Set for PBC 6500


Battery set for PBC 6500 with either 48Vx100Ah or 24Vx200Ah configuration. Supplied with accessory kit for connection of batteries.
Consist of:
Qty Description
4
SBS 100, Battery block, 6/BKC90106/0101
1
Accessory kit
Product Number
BKC 901 06/101
BKC 901 06/102

Length
800 mm
800 mm

Width
300 mm
500 mm

Height
500 mm
500 mm

Weight
144.4 kg
144.4 kg

Voltage
48V
24V

Battery Set for BBC 8500


Battery set for BBS 8500 with either 48Vx100Ah or 24Vx200Ah configuration. Supplied with accessory kit for connection of batteries and Gas collection kit for gathering/ventilation of gas.
Consist of:
Qty Description
4
Lead Acid Battery SBS100, 6/BKC90106/0101
1
Gas collection kit, BKY90144/1
1
Accessory kit, BKY90112/102
Product Number
BKC 901 06/103
BKC 901 06/104
BKC 901 06/105
BKC 901 06/106

58

Length
800 mm
800 mm
800 mm
800 mm

Width
300 mm
300 mm
300 mm
500 mm

Height
500 mm
500 mm
500 mm
500 mm

Weight
144.4 kg
144.4 kg
144.4 kg
144.4 kg

Voltage
48V
24V
48V
24V

59

Power Back-up

Power Back-up

Battery Sets

Battery Sets
Battery Set for BBS2216,V2

Power Back-up Set 48V100Ah

Battery set for BBS 2216,V2 with either 24Vx100Ah, 24Vx200Ah or 48Vx100Ah configuration. Supplied with accessory kit for connection of batteries.

Battery Back-up set for Telecom site supplied with accessories and batteries.

Consist of:
Qty Description
2
Lead Acid Battery SBS100, 6/BKC90106/0101
1
Accessory kit, BKY90113/103
Product Number
BKC 901 06/111
BKC 901 06/112
BKC 901 06/113

Length
800 mm
800 mm
800 mm

Width
300 mm
300 mm
300 mm

Height
500 mm
500 mm
500 mm

Weight
79.2 kg
144.4 kg
144.4 kg

Voltage
24V
48V
24V

Battery Set 48V/100Ah for telecom applications. Supplied with accessory kit for connection of batteries. Voltage:
48 V. Ampere-hours: 100 Ah.
Consist of:
Qty Description
4
Battery block SBS 100, 6/BKC90106/0101
1
Acessory kit
Length
490 mm

Width
470 mm

Height
390 mm

Weight
131 kg

Voltage
48V

Battery set for SSC02, PBC 8200, BBS 6201, PBC 6200, BBU 6101, BBU 6201 and BBS 6101. Supplied with
Spacer and 23" interblock connection kit.
Consist of:
Qty Description
4
Lead Acid Battery, SBS190F, 6/BKC90106/0190
1
23" SBS Interblock connection kit, BKY90151/4
1
Battery Spacer, BKY90114/4
Length
660 mm

Width
540 mm

Height
440 mm

Weight
252.5 kg

Voltage
48 V

The PowerSafe V Front Terminal valve regulated lead acid batteries has been designed specifically for use in applications that demand the highest levels of security and reliability. A premium solution for Telecom applications.
Suitable for 19", 23" and ETSI racking and with all electrical connections at the front. Batteries are designed using
proven gas recombination technology which removes the need for regular water addition by controlling the evolution of hydrogen and oxygen during charging.
-Front terminal connections for fast and easy installation and maintenance
-Suitable for 19", 23" and ETSI racking
-UL94 V-0 flame retardant case and lid
-High reliability
-Proven long service life
In compliance with the requirements of the international IEC 60896-21/22 standard
Classified as Long Life according to the Eurobat Guide 1999
Designed to meet Telcordia SR-4228 requirements
Recognised by UL (UL Standard 1989)
Approved to be shipped as nonhazardous cargo in accordance with the requirements of IMDG (International
Maritime code for Dangerous Goods) and ICAO (International Civil Aviation Organisation)
Consist of:
Qty Description
1
Lead Acid Battery 12V, Valve regulated UL94 V-0, IEC 60896-21/2

60

Width
720 mm

Height
400 mm

Weight
123.48 kg

Power Back-up Set 48V170Ah


Consist of:
Qty Description
4
Battery 12V170AH, 6/BKC90106/0172
1
23"SBS Interblock connection kit, BKY90151/4
1
Spacer, BKY90114/4
Product Number
BKC 901 06/145

Length
561 mm

Width
500 mm

Height
400 mm

Weight
203.13 kg

Power Back-up Set 48V190Ah

Length
395 mm
561 mm
561 mm

Width
108 mm
125 mm
125 mm

Consist of:
Qty Description
4
Battery 12V190AH, 6/BKC90106/0191
1
23"SBS Interblock connection kit,BKY90151/4
1
Spacer, BKY90114/4
Product Number
BKC 901 06/152

Battery Blocks PowerSafe

Product Number
6/BKC 901 06/0102
6/BKC 901 06/0172
6/BKC 901 06/0191

Length
287 mm

Battery Back-up set for Telecom site. Supplied with 23" interblock connection kit, spacers and batteries.

Battery Set 48V/190Ah

Product Number
BKC 901 06/123

Product Number
BKC 901 06/144

Battery Back-up set for Telecom site. Supplied with 23" interblock connection kit, spacers and batteries.

Power Back-up Set 48V/100Ah

Product Number
BKC 901 06/121

Consist of:
Qty Description
4
Battery 12V100AH, 6/BKC90106/0102
1
Accessory kit 48V/DC100AH, BKY90112/120

Height
287 mm
283 mm
316 mm

Ah
100
170
190

Width
500 mm

Height
416 mm

Weight
229.19 kg

Battery accessories
Battery Spacer BKY 901 14/4
The accessory kit shall be used for secure apporpriate distance between four battery blocks positioned on one
shelf.
Consist of:
Qty
Description
4 pcs
Battery separator 25x25x7 mm 4 pcs
1 pcs
Battery separator 20x20x7 mm
4 pcs
Battery separator for temperature sensor cable 65x65x7 mm
Product Number
BKY 901 14/4

Length
800 mm

Width
300 mm

Height
500 mm

Weight
260.5 kg

Battery Spacer BKY 901 14/6


The spacers prevent lateral movement of batteries and assure sufficient airflow between them.
Consist of:
Qty Description
3
Adhesive Spacer 360x10x7mm
Product Number
BKY 901 14/6

Weight
30.8 kg
50.8 kg
57.3 kg

Length
561 mm

Length
360 mm

Width
10 mm

Height
21 mm

Weight
0.04 kg

Height
10 mm
10 mm

Weight
0.072 kg
0.106 kg

SBS Inter Block Connector kits


Connect battery blocks in the SBS system with these kits
Product Number
BKY 901 51/3
BKY 901 51/4

Length
110 mm
110 mm

Width
30 mm
35 mm

61

Power Back-up

Power Back-up

Battery accessories

Battery accessories

Inter Block Connector BKY 901 52/1

Battery Harness SBS

Flexible braided copper connector insulated by heat shrinkable tube.It connects the battery blocks in a short serial
connection(pic2).
Current rating: 250 A
Cross Sectional Area: 50 mm2
Lenght C-C (L2): 371 mm
Hole Diameter: 11.5 x 8.5 mm
Width: 20 mm
Flame retardancy: UL 224-VW 1
Copper stability: ASTM D2671
CSA Certified: C22.2 No 198

This kit braces 4 battery blocks at the cabinet.

Consist of:
Qty - Description
1 - Connector 250A, 50 mm
Product Number
BKY 901 52/1

Length
396 mm

Width
20 mm

Height
5 mm

Weight
0.198 kg

Battery Cable Set


This battery set contains two different power cable assemblies for the supply of the power. The cable assemblies
are ROHS approved. IEC certified/NRTL listed safety. Halogen free: IEC 60754-2. Fire resistance: IEC 60332-1 /
UL 94V.
Consist of:
Qty Description
1
Power Cable Assembly 2AWG 5A,+24VDC, 0.7m
1
Power Cable Assembly 2x50mm2, 175A,-48VDC, 0.8m
2
Guide rail 2

Length
300 mm

Width
300 mm

Height
80 mm

Weight
1.73 kg

The battery adapter shall be used to create front terminal access on SBS 100. Use the terminal adapter during the
first installation of SBS100 and when batteries need to be replaced.
Consist of:
Qty Description
2
Front Terminal Adapter
2
Insulation cover
2
Nut M8
2
Washer M8
Width
90 mm

Height
45 mm

Weight
0.136 kg

The battery adapter set 190 shall be used to create front terminal access on SBS190. The adapter is needed at
the first installation and when replacing batteries.
Consist of:
Qty Description
2
Front terminal adapter
2
Insulation cover
2
Insulation cover for battery
2
Nut M8
2
Washer M8, plain
Length
200 mm

Width
160 mm

Height
100 mm

Weight
0.35 kg

The air stopper guids air flow around battery blocks in cabinets with mechanical air flow.
Length
460 mm

Consist of:
Qty - Description
1 - Battery Tray
Product Number
SXA 134 3383/7

Length
15 mm

Width
440 mm

Height
400 mm

Weight
0.2 kg

LTT 601 157/1


Consist of:
Qty Description
1
Insulated torque wrench 5-25Nm
1
With rectangular drive 9x12 for 1 direct insertion of sockets
1
Insertion socket 10mm
1
Insertion socket 13mm
LTT 601 157/2
Consist of:
Qty Description
1
Insertion socket 10mm
1
Insertion socket 13mm
Length
275 mm
100 mm

Width
35 mm
100 mm

Height
35 mm
10 mm

Weight
0.4 kg
0.5 kg

Battery Tray SBS 1x100ah

Consist of:
Qty - Description
1 - Battery Tray
2 - Spacer
1 - Adhesive Tape

Width
300 mm

Height
10 mm

Weight
0.221 kg

Length
400 mm

Width
110 mm

Height
20 mm

Weight
0.1 kg

Gas Collection Kit SBS 100


The Gas collection kit is used to gather the oxy-hydrogen gas of up to eight battery blocks (6/BKC 901 06/0101) in
the Power Back-up system of the Telecom site. Gas collection kit BKY 901 44/1 and battery block 6/BKC 901
06/0101 is mounted in system BBS 2x16 and BBS 8500.
BKY 901 44/1
Consist of:
Qty Description
1
Gas tube Length 1200mm, internal =6mm, external= 8mm
4
Gas tube Length 95mm , internal =6mm, external= 8mm
3
Gas tube Length 90mm, internal =6mm, external= 8mm
1
L Nipple
4
T Nipple
Product Number
BKY 901 44/1

62

Weight
0.15 kg

The battery tray separates batteries from cabinett shelf or rack shelf.
It collects acid leakage due to spill during installation and transport according to EN-50 272-2.
The tray holds 4 battery blocks with basis 381x104.5 mm.

Product Number
SXA 134 3383/8

Air Stopper for 19 Batteries


Product Number
SXA 215 4207/2

Height
25 mm

The battery tray separates a battery from cabinet shelf or rack shelf. It collects acid leakage due to spill during installation and transport according to EN-50 272-2. The tray holds 1 battery block with basis 387*101,8 mm.

Front Connector Set SBS190

Product Number
SXA 134 5137/2

Width
150 mm

Battery Tray SBS 4x100ah

Product Number
LTT 601 157/1
LTT 601 157/2
Length
145 mm

Length
200 mm

The insulated torque wrench to be used for tightening the battery bolts (to avoid short circuit). Torque range 525Nm.

Front Connector Set SBS100

Product Number
SXA 134 5137/1

Product Number
BKY 901 18/5

Tools

Support 2
Captive Nut M6 for T=0,7-1,7 4
Screw RTK ST 4,2X9,5 6
Screw MRT-LME M6X16 4
Product Number
NTM 201 3966/1

Consist of:
Qty - Description
4 - Strip Lock
4 - Belt 24.4x250 mm
12 - Strap Fastener
8 - Spring
4 - Belt 24.4x 1350 mm

Length
235 mm

Width
235 mm

Height
15 mm

Weight
0.116 kg

63

Power Back-up

Sonepar is representedby:

Battery accessories
Gas Collection Kit SBS 190
The Gas collection kit is used to gather the oxy-hydrogen gas of up to eight battery blocks (6/BKC 901 06/0190) in
the Power Back-up system of the Telecom site. Gas collection kit BKY 901 44/2 and battery block 6/BKC 901
06/0190 is mounted in system BBU9500 and BBS6200
BKY 901 44/2
Consist of:
Qty Description
1
Gas tube Length 1200mm, internal =6mm, external= 10mm
4
Gas tube Length 35mm , internal =6mm, external= 10mm
3
Gas tube Length 130mm, internal =6mm, external= 10mm
1
L Nipple
4
T Nipple
Product Number
BKY 901 44/2

Length
300 mm

Width
300 mm

Height
300 mm

ELEKTROSKANDIASVERIGE
Norrvikenleden97
19183Sollentuna-Sweden
Tel:+46(0)8923500
www.elektroskandia.se
Weight
0.25 kg

VALLENPROVEEDORAINDUSTRIAL
Blvd.AdolfoLopezMateos
ColUniversidadPonienteNo4000
89336TAMPICO-TAMS-Mexico
Tel:+528332301700
www.vallenproveedora.com.mx

ELEKTROSKANDIACHINA
355QinqiaoRoad
JinqiaoExportProcessingZone
201206ShanghaiPRC-China
Tel:+862161002500
www.elektroskandia.com.cn

ESKINDIACOMMERCE&TRADEPVT.LTD.
PlotNo-229/239,RectangleNo51,KhasraNo-02,
VillageKherkiDaula
NH-8,NearGrozToolsFactory
Gurgaon,122004-India
Tel:+911244370867
www.eskindia.in

HAGEMEYERNORTHAMERICA
1460TobiasGadsonBlvd
29407CharlestonSouthCarolina-USA
Tel:+18437452400
www.hagemeyerna.com

64

DIMENSIONALEQUIPAMENTOSELTRICOSS.A.
ViaAntnioCrunesFilho,4530
13481-287LIMEIRA-SP-Brazil
Tel:+551934467400
www.dimensional.com.br

LAWRENCE&HANSONGROUP
456LowerHeidelbergRoad
HeidelbergVic3084-Australie
Tel:+61392433555
www.landhgroup.com.au

You might also like