Professional Documents
Culture Documents
Demo Case
for Burner Management System LMV5...
Operating Instructions
CC1B7988en
14.09.2006
Building Technologies
HVAC Products
Warning notes
To avoid injury to persons, damage to property or the environment, the following warning notes should be observed!
Commissioning notes
Open the demo case by releasing the lateral locks and remove the cover
When opened, plug the enclosed mains cable into the socket
(see photo)
Should you encounter any problems when putting the demo
case into operation, please do not make any manipulations
Operating notes
Parameter
settings
2/8
CC1B7988en
14.09.2006
HVAC Products
HVAC Products
CC1B7988en
14.09.2006
3/8
CAN bus
RS-232
7988z01e/0601
4/8
CC1B7988en
14.09.2006
HVAC Products
Fuel selection button OIL / GAS / INT (fuel selection with the display and programming unit)
7988z03/0301
7988z05/0301
7988z04/0301
Reset / interlock
7988z06/0301
7988z07/0301
7988z09/0301
7988z08/0301
7988z15/0301
7988z14/0301
7988z13/0301
7988z12/0301
7988z11/0301
7988z10/0301
Gas pressure switch for gas valve proving / closed position indicator
Simulation of heat consumption of the simulated controlled system (refer to section Simulation of the controlled system)
Time constant 1 for the simulated controlled system (refer to section Simulation
of the controlled system)
Time constant 2 for the simulated controlled system (refer to section Simulation
of the controlled system)
2. External connections
CAN bus connection for additional actuators (on the right side of the case) and
O2 simulator KF8893-2...
HVAC Products
CC1B7988en
14.09.2006
5/8
Simulation of a
closed control loop
Load controller
Configuration
LC_OptgMode
Sensor Select
MeaseRangePtNi
Int LR
Pt1000
150 C / 302 F
Simulation of a closed control loop is especially suited for demonstrating the adaptation of the internal load controller. To simulate a boiler
temperature increase, the controlled system is simulated by using 2
delay members connected in series.
The delay members have the time constant 1 of 1...50 seconds
and 2 of 50...100 seconds.
Changes to the boilers heat output can be simulated with potentiometer Load.
The graph below shows the progression of boiler temperature when
the burners output suddenly changes at a constant rate (step response).
Characteristic 1 shows the progression of boiler temperature when
using the minimum settings of 1 and 2. The maximum values
of the delay members 1 and 2 produce characteristic 2.
The final temperature level depends on the adjusted burner output
(setting on the LMV5) and the position of potentiometer Load.
To demonstrate the adaptation of the internal load controller of the
LMV5, the following settings are required:
Configuration of the load controller inside the LMV5
6/8
Load controller
Configuration
LC_OptgMode
Sensor Select
Ext Inp X61 U/I
MRange TempSens
SetpointW1
Int LR
Temp.-Sens
0...10 V
100 C
60 C
CC1B7988en
14.09.2006
HVAC Products
= 75 %
= any
= any
= inactive
P / in %
t (in s)
7988d01/0501
Removal of
AZL5
Simulation of the
controlled O2
system
Using the KF8893-2, the O2 signal, O2 sensor temperature, combustion air temperature and flue gas temperature can be simulated.
For that purpose, the KF8893-2... must be connected to the CAN bus
of the KF8893-1 via the 6-pole connector. The potentiometers are
used to manually adjust the respective signals. During initialization of
O2 trim control, the boiler plants delay time is determined in the
course of the adaptation process. To ensure correct simulation, the
O2 value must therefore be slowly changed from the adjusted O2
setpoint to the initial O2 ratio value. It should also be observed that
each time the system is put into operation, the O2 value must be
manually set to 20.9 % 2 % at the end of prepurging. After ignition
and the change to control mode, the O2 value should be reduced to
the O2 ratio value for simulated operation.
HVAC Products
CC1B7988en
14.09.2006
7/8
Type summary
Demo case for LMV5...
KF8893-1
KF8893-1A1
KF8893-1-W
KF8893-1A1-W
KF8893-2
KF8893-2A1
Technical data
General data
Mains voltage
- KF8893-1
- KF8893-1A1
- KF8893-1-W
- KF8893-1A1-W
- KF8893-2
- KF8893-2A1
Mains frequency
Power consumption
Disposal notes
The KF8893... demo case contains electrical and electronic components and must not be disposed of together with household waste.
Local and currently valid legislation must be observed.
http://www.sbt.siemens.com
Subject to change!
8/8
CC1B7988en
14.09.2006
HVAC Products