Professional Documents
Culture Documents
sala
TMA 1800/2100/2300
13dB 2:2 1 AISG
1
E15Z01P26
A
TENTATIVE
27/06/2013
sala
A4
SCHEMATIC DIAGRAM
ANT 0
RX1 21
TX 21
ANT 1
TX-RX
23
TX-RX
23
BY-PASS
23
BY-PASS
23
RX1 18
RX1 21
TX 18
RX1 18
TX 21
RX2 21
BY-PASS
23
RX2 18
TX 18
RX2 21
BY-PASS
23
RX2 18
TX-RX
23
TX-RX
23
LNA, Alarm,
AISG Unit
LP
LP
BTS 0
BTS 1
AISG
RET conn.
ELECTRICAL SPECIFICATION
Frequency range TX DCS 1800MHz
27/06/2013
sala
TMA 1800/2100/2300
13dB 2:2 1 AISG
2
E15Z01P26
A
TENTATIVE
27/06/2013
sala
A4
12 dB + 1.3/ -1.0 dB dB
0.3 dB Max.
25 nS typ.;30 nS Max
+ 22 dBm Min
1.5 dB Typ.; 2.1 dB Max
17 dB Min
17 dB Min
3 dB Max
14 dB Min
14 dB Min
12 dB 1 dB
1.2 dB Max
13 nS typ.;16 nS Max
+ 22 dBm Min
1.5 dB Typ.; 2.0 dB Max
17 dB Min
17 dB Min
2.7 dB max
14 dB Min
14 dB Min
TX path
TX passband frequency range
Insertion Loss
Insertion Loss Ripple TX passband
Return Loss ANT Port TX passband
Return Loss BTS / NODE B Port TX passband
Input TX RMS Power (each module)
RX to TX switching time
2300-2400 MHz
1.6 dB typ
0.7 dB max
20 dB typ; 18 dB min
20 dB typ; 18 dB min
50 W max
4 us max
RX path
RX passband frequency range
Gain RX passband
Gain Ripple RX passband
Output IP3
Noise figure
Return Loss ANT Port
Return Loss BTS / NODE B Port
2300-2400 MHz
12 dB typ; 12 dB +/-1 max/min
+/-0.5 dB max
17 dBm min
1.6 dB typ
20 dB typ; 18 dB min
20 dB typ; 18 dB min
27/06/2013
sala
TMA 1800/2100/2300
13dB 2:2 1 AISG
3
E15Z01P26
A
TENTATIVE
27/06/2013
sala
A4
22 dBm max
2300-2400 MHz
0.9 dB typ
0.6 dB max
14 dB min
14 dB min
Dual feed power supply mode (each BTS port supplies respective LNA)
Supply voltage Operational
Supply Voltage Survival
Programmable dummy load
Power consumption without dummy load
Normal current consumption (CWA mode with dummy load)
Alarm current consumption (CWA mode)
Normal current consumption (non CWA/AISG mode with dummy load)
+7V to +30V
-48V to +48V
0 to 300mA (7-19 VDC) each BTS ports
<4.5W each BTS port
<160mA (8-19 VDC) each BTS ports
190 +/-10 mA (10-19 VDC) each BTS ports
80mA +/- 10mA (19-30 VDC) each BTS port
AISG Single feed power supply mode (BTS0 or BTS 1 supplies both LNAs)
Supply voltage Operational
+7V to +30V
Supply Voltage Survival
-48V to +48V
Programmable dummy load
0 to 300mA (10-19 VDC)
Power consumption without dummy load
<8W
Over current protection at AISG RET0 Output connector (HICCUP-MODE)>2 +/-0,1 A
AISG standard on both BTS ports
1.1&2.0
Logical map Configuration1 1Device-4 Subunits
Signal Interface @ 2.176 MHz on both BTS ports
DC Ground
8/20 s 10KA
MECHANICAL SPECIFICATION
RF connectors
Weight (without mounting equipment)
Volume (without mounting equipment)
Dimensions (without connectors and mounting equipment)
Outside finish
ENVIRONMENTAL SPECIFICATION
Operating temperature range
Humidity
Sealing (with 7/16 connectors closed)
Wind speed
-40 C / +65 C
100 %
IP67
> 55 m/s (200 Km/h)
27/06/2013
sala
TMA 1800/2100/2300
13dB 2:2 1 AISG
4
E15Z01P26
A
TENTATIVE
27/06/2013
sala
A4