Professional Documents
Culture Documents
PRODUCT
INFORMATION
CONTENTS
Chapter 1
PRODUCT INFORMATION
FS-7000+/FS-9000
1-1-3
(U.S.A./Canada)
(Europe/Asia)
1-1
FS-7000+/FS-9000
FS-9000
(U.S.A./Canada)
(Europe/Asia)
FS-7000+/FS-9000
1-2
Printer specifications
Engine
Print method Electrophotography laser scan
Print speed (when printing
multiple copies of the
same page) A4/81/2" 11": 28*1/ 36*2 pages/min.,
B4 (257 364 mm): 18*1/ 22*2 pages/min.,
A3/11" 17": 16*1/ 20*2 pages/min.
Resolution (dpi) 600 horizontal/600 vertical
Smoothing KIR2 (2400 dpi horizontal/ 600 dpi vertical)
First print (A4/81/2" 11" or letter,
23C/73.4F), depending on input
data 10 seconds or less (75*1/100*2 seconds or less with
sleep mode on)
Warm-up time at 23/73.4F 65*1/ 90*2 seconds or less
Maximum duty cycle (A4) 100,000*1/ 150,000*2 pages/month
Laser diode Visible laser
Main charger Scorotron wire
Transferring Biased roller
Separation DC
Drum cleaning Blade
Drum discharging LED array
Fuser Heat and pressure
Paper Plain paper (as specified separately)
Capacity of paper feed tray
(80 g/m2 [0.11 mm thickness]) Cassette: 500 sheets, MP tray: 100 sheets
Capacity of output trays
(80 g/m2 [0.11 mm thickness]) 500 sheets
Controller
CPU PowerPC603e/166 MHz*1,
PowerPC740/233 MHz*2
System ROM size 4 MB, flash DIMM or masked DIMM
Resident font ROM size 4 MB
Main RAM 8 MB*1,16 MB*2
Option API ROM 512 KB (4 Mbit EPROM socket)
Additional RAM (SIMM) 64 MB maximum (72-pin SIMM 2)
Memory card SRAM or flash, JEIDA 4.2/PCMCIA 2.1
See Recommended flash cards in this chapter.
Host interface Parallel: High-speed, bi-directional (IEEE1284),
Serial: RS-232C/RS-422A/Barcord reader (BC-1),
Option, KUIO 2 slots(harddisk drive HD-2, for
network card).
Page description language Prescribe II
Standard emulation modes Line printer, Epson LQ-850, HP LJ 5M(PCL6,PCL),
Diablo 630, KPDL2, KC-GL(HP7550A)
*1: FS-7000+ model
*2: FS-9000 model
1-3
FS-7000+/FS-9000
56 cm (22")
34.5 cm (13 9/16")
56.6 cm (22 5/16")
40.2 kg (88.4 lb.)
56 cm (22")
25.1 cm (9 7/8")
56.6 cm (22 5/16")
19.5 kg (42.9 lb.)
Power requirements
Voltage requirements 120 V AC 10%, 60 Hz 2%.
220 240 V AC 10%, 60 Hz 2%.
Watts Maximum:
1200 W
Normal operation: 710 W*1, 825 W*2
Standby:
200 W*1, 220 W*2
Sleeping:
29 W*1, 31 W*2
Maximum current consumption US/Canada: 10 A
Europe/Asia: 5 A
Environmental requirements
Operating temperature and
humidity 10 to 32.5C (50 to 90.5F), 20 to 80% RH
Maximum altitude 2,000 m (6,500 feet)
Noise emission (Excluding
peaks, measured at 1m from
printer, as per ISO7779) 50*1/54*2 dB (A) maximum/38*1/39*2 dB (A) at
standby/unmeasurably low at sleeping
*1: FS-7000+ model
*2: FS-9000 model
FS-7000+/FS-9000
1-4
Capacity
AMD
AmC001CFLKA
AmC002CFLKA
AmC004CFLKA
AmC010CFLKA
AmC004DFLKA
AmC008DFLKA
AmC020DFLKA
1 MB
2 MB
4 MB
10 MB
4 MB
8 MB
20 MB
Fujitsu
MB98A81063
MB98A81183
MB98A81273
MB98A81373
MB98A81473
1 MB
2 MB
4 MB
8 MB
16 MB
Panasonic
BN-02MHF4C (CC)
BN-04MHF4C (CC)
2 MB
4 MB
Centennial
FL01M-20-11114-03
FL02M-20-11114-03
FL04M-20-11114-03
FL08M-20-11114-03
1 MB
2 MB
4 MB
8 MB
Maxell
EF-2M-TB (DC)
EF-4M-TB (DC)
EF-8M-TB (DC)
EF-16M-TB (DC)
1-5
2 MB
4 MB
8 MB
16 MB
FS-7000+/FS-9000
Option feeder
connector
MP (multipurpose) tray
Front cover
Paper feeder
Power switch
FS-7000+/FS-9000
1-6
Internal assemblies
Drum release lever
(Green colored)
Toner container
Drum unit
Lock lever
Fuser unit
Fuser release
lever
Developer
Feed unit
Rear view
Harddisk
drive slot
Memory card slot
Power receptacle
Parallel interface
connector
Rear panel
Serial interface
connector
Paper cassette
access door
1-7
FS-7000+/FS-9000
Duplexer
(Inboard)
Paper feeder
supplied as
standard
Bulk paper
stacker,
document
finisher, or
mailbox/ sorter
First optional
paper feeder
Second optional
paper feeder
Options
FS-7000+
FS-9000
Duplexer
DU-30/ DU-31
DU-31
Paper feeder
PF-30
PF-30
ST-30
ST-30
Document finisher
Mailbox/ sorter
Envelope feeder
Universal feeder
DF-30/ DF-31
SO-30
EF-1
UF-1
DF-31
SO-30
EF-1
CA-30
CA-30
FS-7000+/FS-9000
1-8
Safety information
Laser notice for service person (U.S.A.)
This printer is certified in the U.S. to conform to the requirements of DHHS 21 Cfr
Subchapter for Class I (1) laser products, and elsewhere is certified as a Class I laser
product conforming to the requirements of IEC 825.
Class I laser products are not considered to be hazardous. The printer contains internally
a Class IIIa (3a) laser that is nominally a 5 milliwatt laser operating in the wavelength region
of 680 nano-meters. The laser system and printer are designed so there is never any human
access to laser radiation above a Class I level during normal operation, user maintenance,
or prescribed service condition.
1-9
FS-7000+/FS-9000
Ozone concentration
Laser printers generate ozone gas (O3) which may concentrate in the place of installation
and cause an unpleasant smell. To minimize the concentration of ozone gas, we recommend
that the laser printer not be installed in a confined area lacking ventilation.
FS-7000+/FS-9000
1-10
Option equipment
The printer may be optionally installed with the following units, with compliance with class
B limits:
EF-1Envelope feeder
DU-30*/ DU-31Duplexer
DO-30Document stacker
HD-2Hard disk unit
PF-30Paper feeder (500 sheets)
ST-30Bulk paper stacker (3000 sheets)
UF-1*Universal feeder
DF-30*/ DF-31Document finisher (1800 sheets)
SO-30Mail box/Sorter
WarningThis equipment has been certified to comply with the limits for a
Class B computing device, pursuant to Subpart J of Part 15 of FCC Rules. Only
peripherals (computer input/output devices, terminals, etc.) certified to comply
with the Class B limits may be attached to this equipment. Operation with non-certified
peripherals is likely to result in interference to radio and TV reception.
1-11
FS-7000+/FS-9000
ISO 7779
Maschinenlrminformationsverordnung 3. GSGV, 18.01.1991: Der hchste Schalldruckpegel
betrgt 70 dB(A) oder weniger gem ISO 7779.
FS-7000+/FS-9000
1-12
Environmental requirements
Environmental conditions
The Environmental requirements section on page Chapter 1-4 should be observed to
ensure the optimum operation of the printer. The use of the printer in a location which does
not satisfy the requirements may result in troubles and risk shortening its service life.
The printer will work best if it is installed in a location that is:
Level and well supported (Place the printer on a sturdy table or desk.)
Not exposed to sunlight or other bright light (not next to an uncurtained window). Do not
place the printer on an unstable cart, stand, or table.
Near an AC wall outlet, preferably one that can be used for the printer alone. The outlet
should have a ground slot, or an adapter should be used. If you use an extension cord,
the total length of the power cord plus extension cord should be 17 feet or 5 meters or less.
Well ventilated, not too hot or cold, and not too damp or dry (See section Environmental
requirements on page Chapter 1-4). If you install the printer where the temperature or
humidity is outside the requirements in section Environmental requirements in chapter 1,
the best print quality may not be expected and there will be an increased chance of paper
jams.
Provide a sufficient clearances around the printer to ensure ventilation and ease of
access.
1-13
FS-7000+/FS-9000
Clearance
Allow the necessary minimum clearance on all sides of the printer (below). A total space of
92 by 138 cm (36 7/8 by 54 5/16") is needed.
1
3
2
Clearance
1 Left
Dimensions
45 cm (17
11/16"),
5/8")
2 Front
60 cm (23
3 Right
45 cm (17 11/16")
4 Back
20 cm (7 7/8")
5 Above
30 cm (11 13/16")
FS-7000+/FS-9000
1-14
Places to avoid
Avoid installing the printer in locations exposed to:
Note on power
Use only the power source voltage conforming to the printers rated power voltage. Do not
use other power sources.
Disconnect the printer from the power source before attempting removal or re-placement
of an electrical component or a printed-circuit board.
The printer should not be connected to a power source until the instruction is given to do
so when performing tests described in this manual.
In connecting the printer power, exercise an extreme care in handling the power supply
or any other electric parts which may give an electric shock.
Before performing maintenance or repair, power from both the power source and the
associated peripheral devices (computer, sorter, etc.) should be disconnected, unless
otherwise specified.
To avoid possible electrical shock, extreme caution must be exercised in handling the
power cord and any other electrical part.
An easily accessible socket outlet must be provided near the equipment.
1-15
FS-7000+/FS-9000
FS-7000+/FS-9000
1-16
Toner storage
The toner contained in the container is susceptible to temperature and humidity. To ensure
the high print quality, store the toner container in a place that satisfies the following
environmental conditions:
Temperature: 20 to 40C (4 to 104F)
Humidity:
15 to 90% RH
Note: If the toner container is removed from the printers developer unit, put it in a
protective bag and keep it in a dark place.
Caution: If the printer is shipped for return, etc., do not ship it with the toner container
installed. Otherwise, toner may leak and contamination may result in the printer.
1-17
FS-7000+/FS-9000