Professional Documents
Culture Documents
The 600 series Digital Monitoring System, designed and manufactured by BEP Marine, is made to meet the requirements of modern boating
and recreational vehicles. Electrical installations on-board the modern boat now incorporate complex AC & DC systems along with extensive tankage
for items such as fuel, fresh water, sewage and grey water. Accurate monitoring of such systems is essential, as a mal-function in any one of the above
areas could cause major damage to expensive equipment and ultimately endanger the vessel or peoples lives. The dot matrix display incorporated in
the 600 series allows for more detailed on-screen information and clarity of viewing. The screen has backlighting for easy night time viewing.
The 600-VM3 has had new features added for 2006. It offers the ability to have 3 voltage inputs
with Hi/Low alarms. It can also be configured as a bilge monitor with selectable legends for different
bilge areas. This allows the 600-VM3 to be either fully configured as a voltmeter or partially as
volts or bilge, eg: position 1 volt meter, position 2 & 3 bilge monitor. Selectable legends allow full
nformation to be shown on the screen to avoid confusion, unlike other digital meters available which
only show confusing digits. LCD screen draws 70% less than equivalent LED screens.
Selectable Legends:
Specifications:
input voltage 10-35 VDC
power consumption 45 ma
power consumption 65 ma
(back lighting on)
dimensions refer above
18
Voltmeter
start batt
house batt
port start
stbd start
house 1
house 2
aux batt
genset
radio batt
winch
bowthrust
van bat
Bilge monitor
bilge aft
bilge mid
bilge fwd
bilge stbd
bilge port
bilge
g mon
Features:
10mm red LEDs giving important systems on information
Ideal for flybridge or remote dash position. Also available with alarm and mute switch.
Backlit labels
SOP PANELS
PART No.
SOP1
SOP1-AL
SOP2
SOP2-AL
SIZE mm
HxWxD
115x127x40
115x127x40
115x239x40
115x239x40
SIZE inches
HxWxD
4.5x5x1.6
4.5x5x1.6
4.5x9x1.6
4.5x9x1.6
LABEL SHEET
LEDS
ALARM
MUTE SW
SET 1
SET 1
SET 1&2
SET 1&2
4
3+1 switch
8
7+1 switch
NO
YES
NO
YES
NO
YES
NO
YES
19
Contour
dc monitor
The 600-DCM monitor offers a comprehensive range of functions to allow full monitoring of your
batteries and charging systems. The 600-DCM monitors voltage on up to 3 battery banks, Amps for
charge and discharge and capacity remaining in amphours / percentage utilising peukerts exponent
(house bank only) with the added function of a bilge monitor allowing 24 hour monitoring of your
bilge pump. This meter is an important addition to modern battery management systems. Selectable
legends allow full information to be shown on the screen to avoid confusion, unlike other digital meters
available, which only show confusing digits. LCD screen draws 70% less than equivalent LED screens.
rate
Accu
Specifications:
input voltage 10-35 VDC
power consumption 45 mA
power consumption 65 ma (back lighting on)
dimensions refer page 18.
20
Contour
ac monitor
The 600-ACM monitor offers full comprehensive monitoring for your AC system from
standard single line inputs to twin line systems as used in the USA (no need for additional
selector switch for AC inputs). The 600-ACM is supplied with an AC transducer, Part No:
AC-VSEN and current transformer Part No: CT-10-3 detailed below. A larger CT, Part No:
CT-HD, is also available where cables are too large to pass through the standard CT.
Diagrams below show basic installation. Selectable legends allow full information to be
shown on the screen to avoid confusion, unlike other digital meters available, which only
show confusing digits. LCD screen draws 70% less than equivalent LED screens.
AC Volts Functions
3 inputs with selectable legends
AC volts Line 1, AC volts Line 2, AC
volts L1 + L2, AC volts panel & AC
volts transfer
High / low volts alarms
(NEW) AC Volts
expanded screen
Shows all voltage inputs on one
screen
Amp Functions
2 AC amps inputs
Selectable legends AC amps,
AC amps line 1 & AC amps line 2
High amps alarm
Frequency Function
0-100 Hz
Frequency alarm
selectable for 50 or 60 Hz
Specifications:
input voltage 10-35 VDC
power consumption 45 mA
power consumption 65 mA (back lighting on)
for remote alarm operation use part
no. 54-27C4
dimensions refer page 18
C-VSEN
The AC-VSEN includes 3 voltage transformers for
up to 3 voltage inputs. Supplied with 600-ACM.
Dimensions:
69 x 69 x 50h mm
(2.75 x 2.75 x 2h inches)
Dimensions:
37.5 W x 39.2 H x 13.7 Dmm
(1.5 W x 1.55 H x .55 D)
hole size: 12mm (0.5)
CT-10-3
21
TLM Features:
Tank level monitoring for up to 3 tanks
14 selectable legends for tank
descriptions eg. Fuel, Water, Blackwater
Hi - Low tank level alarms for 3 tanks
Tank levels displayed in graphic or
percentage format
Part No.
TSTMF-15-30 N
TSTMF-30-60 N
TSTMF-60-100 N
TSSMF-15-30 N
TSSMF-30-60 N
TSSMF-60-100 N
TSTMW-15-30 N
TSTMW-30-60 N
TSTMW-60-100 N
TSSMW-15-30 N
TSSMW-30-60 N
TSSMW-60-100N
150-300
300-600
600-1000
150-300
300-600
600-1000
150-300
300-600
600-1000
150-300
300-600
600-1000
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
YES
TOP
TOP
TOP
SIDE
SIDE
SIDE
TOP
TOP
TOP
SIDE
SIDE
SIDE
new TSI Ultrasonic Tank Sender can be used on fuel (petrol or diesel), fresh water, grey water or black
ks. This means less SKUs to stock.
The TSI is programmable for the following outputs, 240-33ohm, 10-180ohm and 0-5volt.
The TSI offers low profile and standard SAE 5 hole mounting pattern, allowing it to be retrofitted to practically all other sender brands.
The TSI can be programmed for tank dimensions via a computer utalizing BEP Marines propietary TSI software, avoiding experimental
tank filling on site.
The TSI configured to a 0-5v output will connect straight into the BEP 600-TLM digital tank monitor.
When configured to a 240-33ohm or 10-180ohm output the TSI can be connected to teleflex, faria, VDO and many other popular
instrument brands.
95.27 [3 3/4"]
84.88 [3 5/16"]
19.64 [3/4"]
95.43 [3 3/4"]
0.5M
SPECIFICATIONS
Current draw
Tank depth
0 to 2000mm
Mounting
Chemical resistance
Contour
The 600 - DCTLM is designed for installations where space is not available to fit two meters.
Offering most of the same functions and settings as the 600-DCM and 600-TLM.
It offers a compact and economical installation. A full range of selectable legends for battery
banks and tanks is available in the set-up menu. Selectable legends allow full information to be
shown on the screen to avoid confusion, unlike other digital meters available, which only show
confusing digits. LCD screen draws 70% less than equivalent LED screens.
More
information
ONE SCREEN!
The 600-DCTLM is supplied with
LB-450-50mv shunt (refer page 20).
For tank sender info (refer page 22-23).
Specifications:
input voltage 10-35 VDC
power consumption 45 mA
power consumption 65 mA (back lighting on)
for remote alarm operation use part
no. 54-27C4
dimensions refer page 18
24