Wireless Sensor Network - Energy Efficiency Algorithm
Introduction - The wide utilization of Wireless Sensor Networks (WSNs) is obstructed by the severely limited energy constraints of the individual sensor nodes. This is the reason why a large part of the research in WSNs focuses on the development of energy efficient routing protocols. In this paper, a new protocol called Energy aware routing protocol and energy-efficient multi-hop routing protocol, which pursues energy conservation is proposed. The performance evaluation of these algorithm is carried out through simulation tests, which evince the effectiveness of this protocol in terms of network energy efficiency when compared against other well-known protocols.
Recent technological advances have enabled the inexpensive mass
production of sensor nodes, which, despite their relatively small size, have particularly advanced sensing, processing and communication capabilities. A WSN consists of spatially distributed sensor nodes, which are interconnected without the use of any wires [1,2]. In a WSN, sensor nodes sense the environment and OPEN ACCESS Algorithms 2013, 6 30 use their communication components in order to transmit the sensed data over wireless channels to other nodes and to a designated sink point, referred to as the Base Station (BS). BS collects the data transmitted to it in order to act either as a supervisory control processor or as an access point for a human interface or even as a gateway to other networks [3,4]. Through the collaborative use of a large number of sensor nodes, a WSN is able to perform concurrent data acquisition of existing conditions at various points of interest located over wide areas.
Multi-hop energy efficient algorithm
Energy is a precious resource in wireless networks. For many multi-hop networking scenarios, nodes are battery-operated, thus requiring efficient energy management to ensure connectivity across the network. Even when wireless networks are connected to power outlets, due to interference between active links the network may demand excessive energy per unit time (Power) so that the overall performance is reduced. Since energy efficiency is directly connected to the network life-time or network capacity, there have been many efforts to study energy-efficient networks in the wireless network community. In the case of multi-hop wireless networks efficient routing algorithms are critical for network performance. The energy efficiency of multi-hop wireless networks is also receiving increasing attention due to its increasing importance of sensor networks in smart grids.
Disadvantages of Multi-hop energy efficient algorithm :
A disadvantage of this approach is that the server may become a bottleneck in large networks and that the trusted intermediary must be online whenever key establishment is desired. Transitory Keys: : if a node is compromised during the initialization period, the entire network may be compromised and (2) the low-end sensor hardware must ensure that the master key is erased from memory such that recovery is not possible. Preamble Sampling : disadvantage of preamble sampling is that broadcast, which is commonly used in wireless communication, requires a large preamble transmission. In particular, the preamble must be slightly longer than a beacon interval (which is at least on the order of tens of milliseconds and longer if less energy consumption is desired). This is the only way to ensure that all of a nodes neighbors are able to detect the preamble. By contrast, in our protocol, the overhead for a wake-up signal is slightly longer than the time to reliably carrier sense the channel (e.g., typically on the order of tens of microseconds) for both unicast and broadcast packets. Carrier Sensing : The increased hardware complexity and cost to provide an extra wake-up channel. Also, the wake-up channel requires extra bandwidth to avoid interference with the data channel. Finally, the wake-up channel must be designed such that its monitoring does not consume much energy. Obviously, the wake-up channel is of little use, from an energy perspective, if it consumes a large amount of energy idly listening to the channel while the data radio is saving energy by sleeping.
Energy aware routing algorithm
Recent advances in Micro-Electro-Mechanical Systems (MEMS) and low power and highly integrated digital electronics have led to the development of microsensors. These sensors are small, with limited processing and computing resources, and they are inexpensive compared to traditional sensors. These sensor nodes can sense, measure, and gather information from the environment and, based on some local decision process, they can transmit the sensed data to the user. The sensing circuitry measures ambient condition related to the environment surrounding the sensor and transforms them into an electric signal. Processing such a signal reveals some properties about objects located and/or events happening in the vicinity of the sensor. The sensor sends such collected data, usually via radio transmitter, to a command centre (sink) either directly or through a data concentration centre. The basic geographic routing does not use any data structures stored locally on a node apart from the neighbour table. Thus, no information is stored locally. The sending component does not differentiate between the source of the message and an intermediate node on its route. The receiving component needs to handle two different types of messages; one that says that the node is the destination, and the other that specifies the node to be an intermediate node for relaying the message. Both messages are handled in exactly the same way, without any form of distinction. The nodes are connected to a larger network like the Internet via a gateway so that users or applications can access the information that is sent from the sensor nodes. The dotted circle shows the area where sensor nodes are scattered to sense the specific task and then route the sensed processed data to the gateway. The main focus is on sensor field area and this research has proposed an Energy efficient scheme for inter-sensor nodes communication where information relay between these sensor nodes. Proposed algorithm will provide simple and efficient path to nodes for forwarding their messages which will further conserve total energy of the entire network.