Professional Documents
Culture Documents
com
All software you need and all answer test CCNA v4 with 100%
Chapter 6 With 100% Accurate Answers
1. Which command is used to view the RIP routing protocol settings and
configuration?
show version
show ip route
show interface
**show ip protocols
2. Refer to the exhibit. What is the maximum number of RIP routers that could
separate HostA and HostB and still leave the hosts with connectivity to each other?
14
15
**16
17
3. In which situation would a company register for its own autonomous system
number (ASN)?
a static route
a default route
**a RIP route
an OSPF route
an EIGRP route
a directly-connected route
Exterior routing protocols are only used by large ISPs. Interior routing protocols are used
http://testccna-4u.blogspot.com http://allsoft247.blogspot.com
All software you need and all answer test CCNA v4 with 100%
by small ISPs.
Interior routing protocols are used to route on the Internet. Exterior routing protocols are
used inside organizations.
Exterior routing protocols are used to administer a single autonomous system. Interior
routing protocols are used to administer several domains.
**Interior routing protocols are used to communicate within a single autonomous system.
Exterior routing protocols are used to communicate between multiple autonomous
systems.
metric
**subnet mask
area identification
hop count
autonomous system number
7. Which routing protocol is used to exchange data between two different ISPs?
**BGP
EIGRP
OSPF
RIP v2
routerA(config-router)# no version 2
routerA(config)# interface fa0/0
routerA(config-if)# ip address 172.19.0.0 255.255.0.0
**routerA(config-router)# network 192.168.3.0
routerA(config)# no ip default-gateway
9. Refer to the exhibit. If all routers are running RIP and network 10.0.0.0 goes
down, when will R3 learn that the network is no longer available?
in 30 seconds
in 60 seconds
in 90 seconds
**Immediately
http://testccna-4u.blogspot.com http://allsoft247.blogspot.com
All software you need and all answer test CCNA v4 with 100%
11. What is the purpose of the network command used when configuring RIP?
12. Which command would a network administrator use to determine if the routers
in an enterprise have learned about a newly added network?
14. What device enables an ISP to connect with other ISPs to transfer data?
show ip route
show ip rip
debug ip rip
show ip protocols
**show ip rip database
16. Which part of an IP packet does the router use to make routing decisions?
source IP address
source MAC address
**destination IP address
destination MAC address
17. What two types of businesses would benefit from registering as their own
autonomous systems? (Choose two.)
debug ip rip
show ip route
show ip interface
show ip protocols
debug ip rip config
**show ip rip database
19. Why is fast convergence desirable in networks that use dynamic routing
protocols?
**Routers will not allow packets to be forwarded until the network has converged.
Hosts are unable to access their gateway until the network has converged.
Routers may make incorrect forwarding decisions until the network has converged.
Routers will not allow configuration changes to be made until the network has converged.
http://testccna-4u.blogspot.com http://allsoft247.blogspot.com
All software you need and all answer test CCNA v4 with 100%
20. Which two statements describe static routes? (Choose two.)
21. Which two statements or sets of statements describe differences between link-
state and distance vector routing protocols? (Choose two.)
Link-state routing protocols routinely use more bandwidth for updates than do distance
vector routing protocols.
Distance vector routing protocols update all routers at one time. Link-state routing
protocols update one router at a time.
**Link-state routers only know about directly connected routers. Distance vector routers
know about every router in the network.
**Link-state routing protocols update when a change is made. A network using distance
vector routing protocols only updates at a specific interval.
Distance vector routing protocols have limited information about the entire network. Link
state routing protocols know about all routers in the network.
In case of similar topologies, networks using link-state routing protocols typically
converge more rapidly than do networks using distance vector routing protocols.
**BGP
EIGRP
OSPF
RIP
23. Hosts on two separate subnets cannot communicate. The network administrator
suspects a missing route in one of the routing tables. Which three commands can be
used to help troubleshoot Layer 3 connectivity issues? (Choose three.)
**Ping
show arp
**Traceroute
**show ip route
show interface
show cdp neighbor detail
http://testccna-4u.blogspot.com http://allsoft247.blogspot.com
All software you need and all answer test CCNA v4 with 100%
24. What term refers to a group of networks that uses the same internal routing
policies and is controlled by a single administrative authority?
Internet
intranet
virtual private network
**autonomous system