You are on page 1of 4

Instruction for the Casing Slips

Features of the structures:


API Spec 7K SY5049

The casing slips are designed and manufactured in API Spec 7K and SY5049
Slips for Well Drilling. It is manufactured in a structure of multi -segment pieces
with firm structure, light weight and large holding range, which is easy to fit the
changing of the external diameter of the casing pipes due to wear and tear.
Main technical parameters:

Casing OD

in

4.1/2-5

5.1/2-6

6.5/8

7.5/8

8.5/8

9.5/8*

10.3/4*

mm

114.3127

139.7152.4

168.3

177.8

193.7

219.1

244.5

273.1

2628-108

2620-108

2628-144

2619-144

2630-144

2630-156

2630-168

2630-180

13

14

15

181
(82)

192
(87)

209
(95)

Circular Buttons P/N

Total number of segments

9
168
(76)

Weight lb (kg)

12
157
(71)

Top Bore Size of the


Casing Bushing(in

196
(89)

184
(83.5)

166
(75)

14.3/8

Max. Load tons(kN)

16.1/4
250(2250)

in

11.3/4*

13.3/8*

16*

18.5/8*

20*

24*

26*

30*

mm

298.5

339.7

406.4

473.1

508

609.6

660.4

762

Circular Buttons P/N

2627-204

2630-216

2631-252

2626-300

2631-312

2631-360

2631-396

2631-444

Total number of segments

17

18

21

25

26

30

33

37

Weight lb (kg)

260
(118)

258
(117)

308
(140)

367
(166.5)

383
(174)

443
(201)

486
(221)

(247.5)

30

32

36

Casing OD

Top Bore Size of the


Casing Bushing(in

19

Max. Load tons(kN)

250(2250)

21.3/4

26

125(1125)

*.(*This size is furnished with 4 handles)


1

546

UC-3
Type UC-3 Casing slips Main technical parameters:

Type

Casing OD

Circular
Buttons

Total
number of
segments

Handle

Fit bushing

8.5/8 UC-3
7

7.5/8

8.1/8

10.3/4 UC-3
8.5/8

9.5/8

10.3/4

11.3/4~24 UC-3
11.3/4

12.3/4

13.3/8

18.5/8

20

24

10

10

12

17

19

10

10

12

17

19

Fit 4 taper

Fit 3 taper

Operational requirement and points for attention:

:
a.;
b.;
c.;
d.

1)It is necessary to measure the actual external diameter of the casing to see
whether it is in the holding range of the casing slips before using.
2

2)Whether the hinge pin is rotated smoothly and whether there is any blocks
or not should be checked before operation.
3)Knocking the handle and the back cone of the slips with big hammer is
strictly forbidden, and be sure do not drop the slips from higher position to avoid
any damage to the handle and cone surface.
4)The surface of the casing slips should be kept clean by daily cleaning and
the rotary part and back cone should be coated with lubrication oil against rusty.
5)Periodic inspection should be done for the casing slips:
a)Check whether the fixing bolt of the casing slip inserts are
loosed or not in order to avoid the slip inserts dropping to the well.
b)Check whether the casing slip inserts brunt or not.
c)Checking with ruler to see whether the back cone of the casing slips is worn
or not.
d)Checking the hinge pin's condition of the casing slips, to see whether it is
worn or not.
6)The casing slip inserts should be replaced entirely in time once found it is
worn out. Be careful do not use the old inserts with the new one at the same time in
order to avoid damages to the slips body due to concentrated load.
7)Remove the harden granules away from the slips cone surface to reduce the
weariness on the cone surface.
8)Often check the wear condition of the casing slips cone surface in order to
avoid dropping into the well.
9)When the casing slips are not in use for a long time, the slips should be
cleaned and coated with anti-rustic oil and placed in a dry place with good
ventilation.
10)The back cone can not be repaired for further using once it is seriously
worn out. This factory is not responsible for any accident caused by the fact that
the slips holding quality is affected by the self-repairing of the old back cone.

You might also like