You are on page 1of 28

INTRODUCTION & FEATURES

FEATURES & CONTROLS


Mono Channel(EV1804D)
2 Channel(EV254, EV294)
4 Channel(EV424, Ev464, EV484)

2~6
2
3
4

5 Channel(EV594)

SPECIFICATIONS

7~8

INSTALLATION & PRECAUTIONS

SYSTEM WIRING

10~20

Mono Channel system wiring

10~11

2 Channel system wiring

12~14

4 Channel system wiring

15~17

5 Channel system wiring

18~20

TROUBLE SHOOTING

21

WIRING

22

Congratulations on your purchase of a Lanzar EVOLUTION amplifier. You have purchased a quality product designed
and engineered to give you many years of uncompromised musical service. EVOLUTION amplifiers are designed with
the latest technology available, incorporating a DC to DC Switching Power Supply, which provides headroom for
even the most demanding peaks and dynamic ranges found on modern CD's and recordings.

Features
MOSFET switches maintain rated power over a wide range of battery voltages
PWM(Pulse-Width-Modulated) System
2 Ohm Stable Stereo operation
Stereo, Bridge Mode and Tri-Mode System Application Compatible
Variable input level controls for each pair of channels
Variable high and low pass crossover controls
Thermal and speaker short protection circuitry
Power and Protection LED indicators
Bass Boost Circuitry
Nickel plated power, RCA and speaker connectors
High-efficiency, heavy aluminum heatsink
Bass Boost Remote control

1. Input RCA Jacks - These inputs are for signal cables from the source. Always use high quality shielded RCA cables.
2. Line Out RCA Jacks - The LINE OUT allows you to build multiple amplifier systems with out having to use splitter cords
to distribute the signal. Now it is simple a matter of bringing one set of RCAs into the first amplifier,
then using the line out RCA jacks as the feed to the next amplifier.
3. Level Control- Enables the matching of input levels to the output levels from the head unit(or other signal source).
4.Phase Shift control - Allows you to change the phase of your subwoofer from 0 to 180 degrees
to help compensate for timing differences between drivers.

5.Variable Low Pass Filter- When Crossover Mode Selector is in Low Pass Mode, this control limits the frequencies
which will be distributed to the speakers to those below the value to which this is set within the range 50~500Hz.
(MONO AND EV594 SUB@1CH,WITHIN THE RANEG 50 - 250Hz.)
6.Variable High Pass Filter- When Crossover Mode Selector is in High Pass Mode, this control limits the frequencies
which will be distributed to the speakers to those below the value to which this is set within the range 50~500Hz.
(THIS IS MONO AMP SUBSONIC FILTER WITHIN THE RANGE 15 - 45Hz)

7.Bridged Mode
8.Bass Boost Remote Control Input
9.Power & Protection Indicators- Provide instant information on status of amplifier,
including short-circuit and thermal overload alerts.
10.Variable Bass Boost Control- 0~18dB @ 60Hz FIX.
11.High Inputs- Accepts speaker level inputs from head units that do not line level (RCA) outputs.
12.Crossover mode selector - Determines the mode of built-in crossover: low pass(permits only low frequency signals
to pass to speakers), high pass(permits only high frequency signals to pass to speakers),or flat.

13.Speaker Temimal.

RMS at 4 Ohms

400W x 2

800W x 2

250W x 4

375W x 4

500W x 4

Peak at 4 Ohms

800W x 2

1600W x 2

500W x 4

750W x 4

1000W x 4

RMS at 4 Ohm Bridged

800W x 1

1600W x 1

500W x 2

750W x 2

1000W x 2

Peak at 4 Ohm Bridged

1600W x 1

3200W x 1

1000W x 2

1500W x 2

2000W x 2

Low Pass Filter

50Hz~500Hz

50Hz~500Hz

50Hz~500Hz

50Hz~500Hz

50Hz~500Hz

High Pass Filter

50Hz~500Hz

50Hz~500Hz

50Hz~500Hz

50Hz~500Hz

50Hz~500Hz

0 - 18dB @ 60Hz FIX

0 - 18dB @ 60Hz FIX

0 - 18dB @ 60Hz FIX

200mV~6V

Low:200mV~6V
High:400mV ~12V

Low:200mV~6V
High:400mV ~12V

Low:200mV~6V
High:400mV ~12V

Low:200mV~6V
High:400mV ~12V

T.H.D

<0.05%

<0.05%

<0.05%

<0.05%

<0.05%

S/N Ratio

>100dB

>100dB

>100dB

>100dB

>100dB

>60dB

>60dB

>60dB

>60dB

>60dB

15Hz~40KHz

15Hz~40KHz

15Hz~40KHz

15Hz~40KHz

15Hz~40KHz

20Ax2

30Ax3

20Ax2

25Ax3

40Ax3

8.97" x 2..41" x 11.02"

8.97" x 2..41" x 14.17"

8.97" x 2..41" x 12.83"

8.97" x 2..41" x 15.19"

8.97" x 2..41" x 17.16"

Bass Boost Control


Input Sensitivity

Channel Separation
Frequency Response
Fuse(s)
Dimensions:WxHxL(inches)

RMS at 4 Ohms

500W x 1

312W x 4 RMS at 4 Ohms & 750W x 1 RMS at 2 Ohms

RMS at 2 Ohms

1000W x 1

625W x 4 Peak at 4 Ohms & 1500W x 1 Peak at 2 Ohms

RMS at 1 Ohm

2000W x 1

Tri-Mode 625W x 2 RMS at 2 Ohms Bridged & 1000W x 1 RMS at 1 Ohm

Peak at 1 Ohm

4000W x 1

Tri-Mode 1250W x 2 Peak at 2 Ohms Bridged & 1500W x 1 Peak at 1 Ohm

Low Pass Filter

50Hz~250Hz

50Hz~500Hz / 50Hz~250Hz

High Pass Filter

(Subsonic@1CH) : 15Hz ~ 45Hz

50Hz~500Hz

Bass Boost Control

0 - 18dB @ 60Hz FIX

(SUB@1CH) :0 - 18dB @ 60Hz FIX

Low:200mV~6V
High:400mV ~12V

Low:200mV~6V
High:400mV ~12V

T.H.D

<0.05%

<0.05%

S/N Ratio

>85dB

>100dB

Input Sensitivity

Channel Separation
Frequency Response
Fuse(s)
Dimensions:WxHxL(inches)

>60dB
15Hz~250Hz

15Hz-40KHz/ (SUB@1CH) : 15Hz - 250Hz

25Ax3

40Ax3

8.97" x 2..41" x 14.17"

8.97" x 2..41" x 17.16"

Mono

Fuse Rating
MODEL

FUSES

EV 1804D

25A x 3

Fuse Rating
MODEL

FUSES

EV 254

20A x 2

EV 294

30A x 3

Fuse Rating
MODEL

FUSES

EV 424

20A x 2

EV 464

25A x 3

EV 484

40A x 3

Fuse Rating
MODEL

FUSES

EV 594

40A x 3

STOP

2-channel Amplifier
(Operating in Stereo)

2-channel Amplifier
(Operating in
Bridged Mono)

YES!

NO!
MOST TWO-CHANNEL
AMPLIFIERS DO NOT SUPPORT 2-OHM
MONO OPERATION! AMPLIFIER DAMAGE
COULD RESULT!

STOP

4-channel Amplifier
(Operating in Stereo)

4-channel Amplifier
(Operating in
Bridged Mono)

YES!

NO!
MOST FOUR-CHANNEL
AMPLIFIERS DO NOT SUPPORT 2-OHM
MONO OPERATION! AMPLIFIER DAMAGE
COULD RESULT!

Sound Around, Inc.


1600 63rd Street

Brooklyn, NY 1 1204

You might also like