You are on page 1of 3

[KVB] [TEKNOLOGI ELEKTRONIK ETN 103]

RSL CBTA PLAN


KOLEJ VOKASIONAL KEMENTERIAN PELAJARAN MALAYSIA
KOLEJ VOKASONAL BETONG SARAWAK
RANCANGAN SESI LATIHAN SEMESTER 1
Jabatan
Nama Kursus
Kod dan Tajuk Modul
Tarikh / Jangka MAsa
Pelaksanaan

Teknologi Kejeruteraan Elektrik Dan Elektronik


Teknologi Elektronik
ETN 103 Fundamental Of Test Instrument
26 Januari 2015 8 Mei 2015 / 14 minggu

Jam Pertemuan

42 jam

At the end of the course, the students should be able to:1.


2.
3.
4.
5.
6.
7.
8.
9.

Select the correct meter and range for specific measurement.


Calibrate meter for current, volt, ohms.
Select the correct signal generator.
Determine type of waveform and amplitude from signal generator.
Setup and operate oscilloscope.
Measure waveform parameters.
Identify specific tacho generator and reading.
Identify and check the condition of various type of measuring instrument.
Calibrate and keep record of measuring equipment.

BIL

KOMPETENSI

KAEDAH PENGAJARAN

Select the correct meter

Calibrate meter for current,


volt, ohms

Confirm range selection using


digital meter

State the difference between analogue and digital meter


according to its performance.
Explain and identify the choice of features (AC, DC,
OHMS etc.) according to its specification.
Explain the selection of meter range according to safety
operating limit.
Identify correct scale range according to its specification.
Identify the polarity of meter probe according to operation
manual.
Identify suitable reference unit to confirm reading
according to measurement.
Perform calibration on Current, Volt, and Ohm according to
SOP.
Perform zero error reading according to standard.
Perform general check on meter according to operation
manual.
Follow the specification and safety rule according to safety
precaution procedure.
Identify the application of various features according to
manual specification.
Explain the types of digital meter according to operation
manual

KAEDAH PENTAKSIRAN

BAHAN / SUMBER

Soalan lisan
latihan

Nota powerpoint
Lcd projector
Bahan sebenar
Kertas latihan

Soalan lisan
Latihan
Ujian
amali

Nota powerpoint
Lcd projector
Bahan sebenar
Kertas latihan
Kertas kerja amali

Latihan
Kerja amali

Nota powerpoint
Lcd projector
Bahan sebenar
Kertas kerja amali

[KVB] [TEKNOLOGI ELEKTRONIK ETN 103]

Identify range selection using


analogue meter

Select the correct signal


generator

Determine type and amplitude


of wave form.

Determine types of waveform.

1.0. Connect oscilloscope to


circuit.

Set oscilloscope

10

Clarify waveform parameters

Determine the function and operation of digital meter


according to operation manual.
Perform the measurement of digital meter according to
measurement requirement.
Confirm the correct polarity and range selection according
to measurement requirement
Identify application of various features according to manual
specification.
Explain the types of analogue meter according to operation
manual.
Determine the function and operation of analogue meter
according to operation manual.
Perform the measurement of analogue meter according to
measurement requirement.
Identify the correct polarity and range selection according
to measurement requirement.
Explain the appropriate application of waveform according
to measurement requirement.
Identify the waveform according to measurement
requirement

Latihan
Tugasan

Nota powerpoint
Lcd projector
Kertas tugasan

Latihan
Kerja amali

Nota powerpoint
Lcd projector
Buku teks aplikasi elektrik dan elektronik
Papan dan peralatan lukisan
Kertas lukisan
Kertas tugasan
Kertas kerja
Nota powerpoint
Lcd projector
Kertas kerja amali

Explain the amplitude of waveform according to


measurement requirement.
Perform signal checking and selection according to
operation manual.
Perform general checking of signal generator according to
operation manual.
Select types of waveform.
Determine the application of waveform according to
requirements.
Identify the scale selection of waveform (bandwidth)
according to measurement requirement.
Operates the signal generator according to SOP.
State the feature of oscilloscope according to manual
specification.
Explain the connection procedure according to manual
operation.
Identify the input channel according to its requirement.
Perform scope accessories according to manual operation.
range according to operation manual.
Perform setting range to make measurement according to
requirement.

Latihan
Tugasan

Explain the types of waveform according to manual


specification.

Latihan
Kerja amali

Nota powerpoint
Lcd projector
Kertas kerja amali

Kuiz
latihan

Nota powerpoint
Lcd projector

Soalan lisan
Amali

Nota powerpoint
Lcd projector
Buku teks aplikasi elektrik dan elektronik

Latihan
Tugasan

Nota powerpoint
Lcd projector

[KVB] [TEKNOLOGI ELEKTRONIK ETN 103]

11

Describe specification of tacho


generator

12

Explain tacho generator reading

13

1.0. Identify the various types


of measuring equipment
and check its condition.

14

Check for calibration of


measuring equipment.

15

Keep records and documents on


measuring instrument

Perform time/div and volts/div according to measurement


requirement.
Calculate the actual measured parameters according to
visualized waveform.
Identify the tacho generator specification according to
operation and service manual.
Explain the tacho generator application according to service
manual.
Identify the output terminal according to operation manual
Explain the principle operation of tacho generator
according to operation manual.
Perform generator speed by tacho meter according to SOP.
Perform tacho generator reading according to SOP.
Compare reading of tacho meter to normal mechanical
RPM meter according to measurement
Explain the types of measuring equipment according to
measurement requirement.
Explain the basic functions of measuring equipments
according to requirement.
Identify the different ranges and parameter of measuring
equipment according to its requirement.
Perform selection of equipment for the job according to
requirement.
Perform measuring equipments condition according to
operation and service manual.
Explain the basic parameters for calibration of measuring
equipment according to operation manual
Perform calibration of measuring equipment according to
operation and service manual.
Check calibration data of equipment according to
manufacturer manual.
Check calibration date and validity periods according to
maintenance requirement
Identify the calibration data of equipment according to its
calibration procedure.
Perform equipment records according to workshop
management standard.

Amali

Kertas kerja

Soalan lisan
latihan

Nota powerpoint
Lcd projector
Set latihan

Soalan lisan
Latihan

Nota powerpoint
Lcd projector
Kertas tugasan

Latihan
Kerja amali
Folio

Nota powerpoint
Lcd projector
Kertas tugasan
Kertas kerja

Latihan
Amali

Nota powerpoint
Lcd projector
Bahan sebenar
Kertas kerja

Amali
Tugasan

Nota powerpoint
Lcd projector
Bahan sebenar
Kertas kerja

You might also like