You are on page 1of 3

DOC. NO.

P.O. Box 4808


Carrier Parkway
Syracuse, New York 13221

Carrier
A United Technologies Company

LAST NO.

PP47-13

Material Specification
TITLE:

ISSUE
DATE

PAGE

SUPERSEDES DOC. NO.

DATED

AUTHORIZATION NO.

REVISION

OF

POE Lubricant, ISO VG220 (Gen. Purpose w/o Lubricity Additives)


INITIATED BY / DATE

MANAGEMENT APPROVAL / DATE

Steve Shoulders 5/26/09

Dave Rockwell 5/26/09

REFERENCE:

ORIGINATED

STATUS:

(C) = CRITICAL CHARACTERISTICS


NA = NOT APPLICABLE

APPROVAL COPY

SCOPE: This specification establishes the requirements for inhibited polyolester based synthetic compressor
lubricant containing no lubricity enhancing additives. This material is suitable for use in screw compressors
for general purpose refrigeration and air conditioning applications.
MATERIAL: For Carrier plants to purchase materials covered by this specification, and be used in Carrier
products, the material must be approved by Engineering and the suppliers quality system must be
Qualified/Certified by the Carrier user plant.
SUPPLIER APPROVAL: Carrier may elect to test, in accordance with the requirements of this specification,
a quantity of material necessary to give valid results. The material must be supplied from a production run
using standard production methods. Only material that has met all requirements will be classified as
approved. Approved suppliers are listed on the last page of this specification.
SUPPLIER QUALIFICATION/CERTIFICATION: The Carrier user plant, or designated lead purchasing
plant, must qualify/certify all suppliers of production materials in accordance with the existing Carrier
Supplier Quality Assurance Requirements.
PERFORMANCE REQUIREMENTS:
The following requirements shall be met by all materials covered by this specification.
METHOD
1. ISO Viscosity Grade
220
ASTM D2422
2. Viscosity, cSt at 40C (104F)
cSt at 100C (212F)

198 to 242
18 to 21

ASTM D445

3. Viscosity Index (Typical)

120

ASTM D2270

4. Density (g/ml) @ 20C

.973 - .981

ASTM D1298

5. Pour Point, F (C)

14 (-10) max.

ASTM D97

6. Flash Point, F (C) (COC)

392 (200) min.

ASTM D92

P R I N T E D

C O P I E S

O F

T H I S

D O C U M E N T

A R E

U N C O N T R O L L E D

NO DEVIATION FROM THE CONSTRUCTION DEFINED BY AN APPROVED SAMPLE OR DETAILED SPECIFICATION (ON FILE IN THE ORDERING
DIVISIONS ENGINEERING DEPARTMENT) WILL BE MADE WITHOUT WRITTEN APPROVAL FROM THE ORDERING DIVISIONS
ENGINEERING DEPARTMENT.

This document and the information contained therein is proprietary to Carrier Corporation and shall not be used or disclosed to
others, in whole or in part, without the written authorization of Carrier Corporation.
Filename: PP47-13.DOC

Savedate: 5/25/2009 10:56:00 AM User: CMS

PAGE

2 OF 3

TITLE:

DATE

POE Lubricant, ISO VG220 (Gen. Purpose w/o Lubricity Additives)

DOCUMENT NUMBER

5/26/09

7. Moisture Content, (ppm)

50 max.

ASTM D1533

8. Acid Number, mg KOH/g

0.05 max.

ASTM 974

9. Miscibility Range with R-22 F(C)


with R-134a F(C)

-90 to 200 (-68 to 93)


10 to 180 (-12 to 82)

PP47-13

10. Copper Corrosion Test, 3 hrs. at 100C (212F) Class 1A min.

ASTM D130

11. Dielectric Strength (0.1 in. gap)

25 kV min.

ASTM D877

12. Anti-Wear Characteristics

< 45 mg of wear

ASTM D-2670 Falex Method, 30


min. R134a bubbling through the
oil at 400 lb. load, no temp.
control.

13. Sealed Tube Stability with Copper and Steel


- TAN (mg KOH/g)
- Oil and R134a
- Oil and R12

ASHRAE 97, 175C for 14 days


< 0.5
< 0.1% R-134a decomposition
< 2.5% R-22 formed

14. Hydroxyl Number (mg KOH/g)

< 4.5

ASTM D1957

15. Hydrolytic Stability: TAN (mg KOH/g)

< 1.0

800 ppm H20 121C, 7 days

SPECIAL REQUIREMENTS:
Qualification Testing: Oil submitted for qualification testing must represent current production and be
accompanied by the latest OSHA 20 form (MSDS). The sample will be tested for compliance to the tests in
Performance Requirements and any other CML Product Engineering deems necessary (e.g., a trial production
or field test).
Acceptance And Rejection: Incoming shipments of oil may be tested for conformance to any or all of the
requirements listed in the Performance Requirements. The oil shall also be tested for conformance to the file
sample using gas chromatography. Failure to pass any of the tests may be cause for rejection of the shipment.
MATERIAL SAFETY DATA SHEET:
All materials covered in this specification must have a recent (< 2 years old) copy of an OSHA 20 form
(MSDS) or applicable regional form disclosing hazardous material content on file in the Corporate Industrial
Hygiene Department. Suppliers must supply a copy with each material submitted for qualification or upon
changes in material content or rules governing such disclosures. The Engineering Department requesting this
specification is responsible for delivering the correct form to the Corporate Industrial Hygiene Department.

This document and the information contained therein is proprietary to Carrier Corporation and shall not be used or disclosed to
others, in whole or in part, without the written authorization of Carrier Corporation.
Filename: PP47-13.DOC

Savedate: 5/25/2009 10:56:00 AM User: CMS

PAGE

3 OF 3

TITLE:

POE Lubricant, ISO VG220 (Gen. Purpose w/o Lubricity Additives)

DATE

DOCUMENT NUMBER

5/26/09

PP47-13

NOTE: THIS PAGE IS NOT TO BE COPIED FOR PROSPECTIVE VENDOR USE.


APPROVED SUPPLIER

MATERIAL DESIGNATION

Lubrizol

Emkarate RL 220H

Applications:
Carrier screw compressors

This document and the information contained therein is proprietary to Carrier Corporation and shall not be used or disclosed to
others, in whole or in part, without the written authorization of Carrier Corporation.
Filename: PP47-13.DOC

Savedate: 5/25/2009 10:56:00 AM User: CMS

You might also like