You are on page 1of 4

Additional Input for PD 5500, Annex G

Allowable Stress Increase Factor (Membrane + Bending)


This factor is multiplied by the allowable stress f, to obtain an allowable stre
ss for the
maximum membrane plus bending stress intensity. These stresses are in rows 27, 2
8 and
29 in the printout samples in PD 5500 Annex G. This entry normally has a value o
f 2.25 or
lower. The program will use a value of 2.0 for this factor for stresses computed
at the edge
of the pad.
Allowable Stress Increase Factor (Membrane)
This factor is multiplied by the allowable stress f, to obtain an allowable stre
ss for the
maximum membrane stress intensity. These stresses are in rows 32, 33 and 34 in t
he printout
samples in PD 5500 Annex G. This entry normally has a value of 1.2 or lower.
Nozzle Inside Projection
If this nozzle has a projection inside of the vessel, enter that length into thi
s field. This
value is used to determine the pressure stress intensification factor from the g
raphs in Section
3 of the PD 5500 Code. These curves for Cers/eps have been digitized and are use
d by
the program. All of the curves for protruding and flush nozzles are included for
analysis.
Stiffened Length of Vessel Section
Enter in the length of the vessel on which this nozzle lies. For vessels without
stiffeners or
cones this would be the entire vessel length accounting for the heads as necessa
ry. This
value is used along with the "Distance from left Tangent" field to compute the e
quivalent
length for off center loading.
Offset from Left Tangent Line
Enter in the distance that the centerline of the nozzles is with respect to the
left tangent line
or appropriate line of support. This value is used in conjunction with the vesse
l length to
compute the equivalent length for off center loading.
Is the Location of the Nozzle in the Vessel Spherical?
If the nozzle is located within the spherical portion of an elliptical or torisp
herical head or
is in a spherical head then check this box. If you are entering this data manual
ly ensure
that you are entering the spherical diameter. This is especially important for n
ozzle located
in elliptical heads. Checking this box causes the program to access the various
curves used
to compute the spherical factors for nozzles connected to spheres per Annex G.
PVElite - User Guide Sample Calculation
The WRC 297/Annex G Module 27-7
Sample Calculation
Input Echo, WRC297 Item 1, Description: WRC NOZ
Diameter Basis for Vessel Vbasis OD
Corrosion Allowance for Vessel Cas 0.0000 in.
Vessel Diameter Dv 120.000 in.
Vessel Thickness Tv 1.000 in.
Vessel Stress Concentration Factor Scfn 0.000
Diameter Basis for Nozzle Nbasis OD

Corrosion Allowance for Nozzle Can 0.0000 in.


Nozzle Diameter Dn 12.000 in.
Nozzle Thickness Tn 0.375 in.
Nozzle Stress Concentration Factor Scfv 0.000
Design Internal Pressure Dp 100.00 psig
Radial Load P 100.00 lb.
Circumferential Shear Vc 200.00 lb.
Longitudinal Shear Vl 300.00 lb.
Torsional Moment Mt 400.00 ft.lb.
Circumferential Moment Mc 0.00 ft.lb.
Longitudinal Moment Ml 0.00 ft.lb.
Include Axial Pressure Thrust No
Stress Computations at the Edge of the Nozzle
--------------------------------------------WRC 297 Curve Access Parameters:
Nr/P = 0.082
Mr/P = 0.109
M0/P = 0.084
N0/P = 0.209
MrD/Mc = 0.185
NrDL/Mc = 0.118
M0d/Mc = 0.174
N0DL/Mc = 0.150
MrD/Ml = 0.143
NrDL/Ml = 0.098
M0D/Ml = 0.121
N0DL/Ml = 0.300
VESSEL Stresses
LONGITUDINAL PLANE Au Al Bu Bl
(Stresses Normal to Top Top Bottom Bottom
longitudinal plane) Outside Inside Outside Inside
-----------(psi )-----------Outplane Membrane (P ) 0 0 0 0
Outplane Bending (P ) 0 0 0 0
Outplane Membrane (Mc) 0 0 0 0
Outplane Bending (Mc) 0 0 0 0
Outplane Membrane (ML) 0 0 0 0
Outplane Bending (ML) 0 0 0 0
Normal Pressure Stress 7139 18444 7139 18444
----------------------- -------- -------- -------- -------Outplane Stress Summary 7139 18444 7139 18444
VESSEL Stresses
LONGITUDINAL PLANE Au Al Bu Bl
(Stresses Normal to Top Top Bottom Bottom
longitudinal plane) Outside Inside Outside Inside
Sample Calculation PVElite - User Guide
27-8 The WRC 297/Annex G Module
-----------(psi )-----------Inplane Membrane (P ) 0 0 0 0
Inplane Bending (P ) 0 0 0 0
Inplane Membrane (Mc) 0 0 0 0
Inplane Bending (Mc) 0 0 0 0
Inplane Membrane (ML) 0 0 0 0
Inplane Bending (ML) 0 0 0 0
Inplane Pressure Stress 5949 -1189 5949 -1189
----------------------- -------- -------- -------- -------Inplane Stress Summary 5949 -1189 5949 -1189
VESSEL Stresses
LONGITUDINAL PLANE Au Al Bu Bl
(Shear stress normal to Top Top Bottom Bottom

longitudinal plane) Outside Inside Outside Inside


-----------(psi )-----------Outplane Shear (Vc) 10 10 -10 -10
Outplane Shear (Vl) 0 0 0 0
Outplane Shear (Mt) 21 21 21 21
----------------------- -------- -------- -------- -------Shear Stress Summary 31 31 11 11
VESSEL Stresses
LONGITUDINAL PLANE Au Al Bu Bl
(Stress Intensities Top Top Bottom Bottom
Outside Inside Outside Inside
-----------(psi )-----------Two * Max Shear Stress 7139 19633 7139 19633
VESSEL Stresses
CIRCUMFERENTIAL PLANE Cu Cl Du Dl
(Stresses Normal to Left Left Right Right
circumferential plane) Outside Inside Outside Inside
-----------(psi )-----------Outplane Membrane (P ) 0 0 0 0
Outplane Bending (P ) 0 0 0 0
Outplane Membrane (Mc) 0 0 0 0
Outplane Bending (Mc) 0 0 0 0
Outplane Membrane (ML) 0 0 0 0
Outplane Bending (ML) 0 0 0 0
Normal Pressure Stress 12494 5949 12494 5949
----------------------- -------- -------- -------- -------Outplane Stress Summary 12494 5949 12494 5949
VESSEL Stresses
CIRCUMFERENTIAL PLANE Cu Cl Du Dl
(Stresses parallel to Left Left Right Right
circumferential plane) Outside Inside Outside Inside
-----------(psi )-----------Inplane Membrane (P ) 0 0 0 0
Inplane Bending (P ) 0 0 0 0
Inplane Membrane (Mc) 0 0 0 0
Inplane Bending (Mc) 0 0 0 0
Inplane Membrane (ML) 0 0 0 0
Inplane Bending (ML) 0 0 0 0
Inplane Pressure Stress 15469 -1189 15469 -1189
----------------------- -------- -------- -------- -------Inplane Stress Summary 15469 -1189 15469 -1189
VESSEL Stresses
CIRCUMFERENTIAL PLANE Cu Cl Du Dl
(Shear stress normal to Left Left Right Right
circumferential plane) Outside Inside Outside Inside
-----------(psi )-----------Outplane Shear (Vc) 0 0 0 0
PVElite - User Guide Sample Calculation
The WRC 297/Annex G Module 27-9
Outplane Shear (Vl) -15 -15 15 15
Torsional Shear (Mt) 21 21 21 21
----------------------- -------- -------- -------- -------Shear Stress Summary 6 6 36 36
VESSEL Stresses
CIRCUMFERENTIAL PLANE Cu Cl Du Dl
(Stress Intensities Left Left Right Right
Outside Inside Outside Inside
-----------(psi )-----------Two * Max Shear Stress 15469 7138 15469 7138
NOZZLE Stresses

LONGITUDINAL PLANE Au Al Bu Bl
(Stresses in the Top Top Bottom Bottom
hoop direction) Outside Inside Outside Inside
-----------(psi )-----------Hoop Membrane (P ) 0 0 0 0
Hoop Bending (P ) 0 0 0 0
Hoop Membrane (Mc) 0 0 0 0
Hoop Bending (Mc) 0 0 0 0
Hoop Membrane (ML) 0 0 0 0
Hoop Bending (ML) 0 0 0 0
Hoop Pressure Stress 1741 1861 1741 1861
----------------------- -------- -------- -------- -------Hoop Stress Summary 1741 1861 1741 1861
NOZZLE Stresses
LONGITUDINAL PLANE Au Al Bu Bl
(Stresses Normal to Top Top Bottom Bottom
pipe cross-section) Outside Inside Outside Inside
-----------(psi )-----------Axial Membrane (P ) 0 0 0 0
Axial Bending (P ) 0 0 0 0
Axial Membrane (Mc) 0 0 0 0
Axial Bending (Mc) 0 0 0 0
Axial Membrane (ML) 0 0 0 0
Axial Bending (ML) 0 0 0 0
Axial Pressure Stress 870 870 870 870
----------------------- -------- -------- -------- -------Axial Stress Summary 870 870 870 870
NOZZLE Stresses
LONGITUDINAL PLANE Au Al Bu Bl
(Shear stress) Outside Inside Outside Inside
-----------(psi )-----------Shear due to (Vc) 28 28 -28 -28
Shear due to (Vl) 0 0 0 0
Shear due to Torsion 56 56 56 56
----------------------- -------- -------- -------- -------Shear Stress Summary 84 84 28 28
NOZZLE Stresses
LONGITUDINAL PLANE Au Al Bu Bl
(Stress Intensities Outside Inside Outside Inside
-----------(psi )-----------Two * Max Shear Stress 1749 1868 1741 1861
NOZZLE Stresses
CIRCUMFERENTIAL PLANE Cu Cl Du Dl
(Stresses in the Left Left Right Right
hoop direction) Outside Inside Outside Inside
-----------(psi )-----------Hoop Membrane (P ) 0 0 0 0
Hoop Bending (P ) 0 0 0 0
Sample Calculation PVElite - User Guide
27

You might also like