Professional Documents
Culture Documents
HUMIDIFIER OPERATION
SET TEMP
ROOM TEMP
CHECK
HEATER
FAN SPEED
HI
MED
LO
TEST RUN
TIMER
ON
OFF
FILTER
6
5
9
4
Set
8
10
OPERATION DISPLAY
10
ON/OFF BUTTON
hr.
HEATER BUTTON
Used to turn on an electric Heater when an
electric heater is installed.
Rev. No.: 1
Be sure to connect
the wires to CN REMO
(Main board)
CN REMO
Brown
Red
Yellow
el
Lever carefully
under plate and open
using a screw
driver, etc.
PROCEDURE OF INSTALLATION
1. Fix the under plate on the wall by self tapping
screws (accessory).
2. Make a slit (Part A) at the top side of the remote
control body by nipper.
3.Rout the cord as shown in the following figure. In
this case, push the cord into the grooved around
the case(Part B).
4. Hook the remote control unit on the under plate.
Front case
Th
ow
er
pa
rt
Remote
controller
body
Remote
control cord
(Part A)
Remote
control unit
Face of wall
Upper notch
Face of wall
Upper notch
Under plate
Tapping screw
(Accessory)
Upper flange
Push hand
(Part B)
Lower notch
FIXING OF REMOTE
CONTROL CORD
1. Fix the cord clamps on the
wall by 3 tapping
screws(Local supply).
2. Fix the remote control cord.
Under plate
Remote
control unit
Screw
(Local supply)
Remote
control cord
Lower notch
Switch box
(Local supply)
Cord
clamp
1
HUMIDIFIER OPERATION
SET TEMP
ROOM TEMP
HI
MED
LO
DEFROST
TEST RUN
CHECK
HEATER
PREHEAT
FAN SPEED
TIMER
ON
OFF
hr.
FILTER
Open the door of the remote controller. To select Cooling operation, press the
Operation Mode Selection button.
Each time the button is pressed, the operation mode is shifted in the direction of
the arrow.
HUMIDIFIER OPERATION
SET TEMP
ROOM TEMP
Set
CHECK
HEATER
PREHEAT
DEFROST
FAN SPEED
HI
MED
LO
TEST RUN
TIMER
HUMIDIFIER OPERATION
ON
OFF
hr.
FILTER
CHECK
HEATER
Cooling
SET TEMP
ROOM TEMP
PREHEAT
DEFROST
FAN SPEED
HI
MED
LO
TEST RUN
TIMER
ON
OFF
hr.
FILTER
Soft Dry
Set the temperature lower than the room temperature. The temperature can be
set within a range of 18C~30C in 1C increment.
HUMIDIFIER OPERATION
SET TEMP
FAN SPEED
ROOM TEMP
CHECK
HEATER
PREHEAT
DEFROST
TIMER
ON
OFF
HI
MED
LO
hr.
TEST RUN
FILTER
1
HUMIDIFIER OPERATION
SET TEMP
ROOM TEMP
HI
MED
LO
DEFROST
TEST RUN
CHECK
HEATER
PREHEAT
FAN SPEED
TIMER
ON
OFF
hr.
FILTER
the door of the remote controller. To select Soft Dry operation, press the
Operation Mode Selection button.
2 Open
Each time the button is pressed, the operation mode is shifted in the direction of
the arrow.
HUMIDIFIER OPERATION
Set
SET TEMP
ROOM TEMP
CHECK
HEATER
PREHEAT
DEFROST
FAN SPEED
HI
MED
LO
TEST RUN
TIMER
FILTER
HUMIDIFIER OPERATION
SET TEMP
ROOM TEMP
HI
MED
LO
DEFROST
TEST RUN
CHECK
HEATER
PREHEAT
FAN SPEED
CHECK
HEATER
PREHEAT
DEFROST
FAN SPEED
HI
MED
LO
TEST RUN
TIMER
ON
OFF
hr.
FILTER
Soft Dry
SET TEMP
ROOM TEMP
hr.
Cooling
HUMIDIFIER OPERATION
ON
OFF
TIMER
ON
OFF
hr.
FILTER
2 Open the door of the remote controller. Press the Fan button.
HUMIDIFIER OPERATION
SET TEMP
ROOM TEMP
Set
CHECK
HEATER
PREHEAT
DEFROST
FAN SPEED
HI
MED
LO
TEST RUN
TIMER
ON
OFF
hr.
FILTER
HUMIDIFIER OPERATION
SET TEMP
ROOM TEMP
CHECK
HEATER
PREHEAT
DEFROST
FAN SPEED
TEST RUN
TIMER
ON
OFF
HI
MED
LO
hr.
FILTER
Set
HUMIDIFIER OPERATION
SET TEMP
FAN SPEED
ROOM TEMP
HI
MED
LO
DEFROST
TEST RUN
CHECK
HEATER
PREHEAT
TIMER
ON
OFF
hr.
FILTER
Set
To stop this operation, press the electric heater operation button once again or ON/OFF button, then all functions will stop.
If the MICOM takes the singnal of stopping this mode, approximately 60 seconds delay time is set to cool the electric heater.
In Cooling Mode and Fan Operation Mode, it is impossible to operate this Mode.
HUMIDIFIER OPERATION
SET TEMP
FAN SPEED
ROOM TEMP
HI
MED
LO
DEFROST
TEST RUN
CHECK
HEATER
PREHEAT
TIMER
ON
OFF
hr.
FILTER
Set
Set
ATION
SET TEMP
ROOM TEMP
HI
MED
LO
DEFROST
TEST RUN
CHECK
HEAT
FAN SPEED
TIMER
HUMIDIFIER OPERATION
hr.
HEATER
FILTER
SET TEMP
ROOM TEMP
OFF
HI
MED
LO
DEFROST
TEST RUN
CHECK
PREHEAT
FAN SPEED
Set
TIMER
ON
hr.
FILTER
Self-Diagnosis Function
'CHECK' will flash on the remote controller display when a problem occurs. Then please contact your dealer.
P/No.: 3828A30037C
June, 1999
Printed in Korea