Professional Documents
Culture Documents
Page
INTRODUCTION ........................................................................... 1
Revision History ....................................................................... 1
Trademark Information .................................................................. 1
Related Publications ................................................................... 2
Admonishments ....................................................................... 2
1. GENERAL ............................................................................ 2
2. DESCRIPTION......................................................................... 3
A.
B.
C.
3. INSTALLATION ........................................................................ 8
A.
B.
C.
D.
Cross-Connections ................................................................ 11
E.
4. OPERATION ......................................................................... 12
5. MAINTENANCE....................................................................... 12
A.
B.
INTRODUCTION
This user manual describes the ADC 84-Circuit DSX-1 Panels and their use in DSX-1
applications. Throughout this manual, these will be referred to as panels.
Revision History
ISSUE
DATE
Issue 1
11/92
Original.
Issue 2
09/98
Trademark Information
ADC and ADC Telecommunications are registered trademarks of ADC Telecommunications, Inc.
4-24883-0800
Page 1
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
Related Publications
Listed below are related manuals, their content, and their publication numbers. Copies of these
publications can be ordered by contacting the ADC Technical Assistance Center at 1-800-366-3891
(in U.S.A. or Canada) or 612-946-3000, extension 3475 (outside U.S.A. and Canada).
Title/Description
ADCP Number
80-303
80-322
Admonishments
Important safety admonishments are used throughout this manual to warn of possible hazards to
persons or equipment. An admonishment identifies a possible hazard and then explains what may
happen if the hazard is not avoided. The admonishments in the form of Dangers, Warnings,
and Cautions must be followed at all times. These warnings are flagged by use of the
triangular alert icon (seen below), and are listed in descending order of severity of injury or
damage and likelihood of occurrence.
Danger: Danger is used to indicate the presence of a hazard that will cause severe
personal injury, death, or substantial property damage if the hazard is not avoided.
Warning: Warning is used to indicate the presence of a hazard that can cause severe
personal injury, death, or substantial property damage if the hazard is not avoided.
Caution: Caution is used to indicate the presence of a hazard that will or can cause
minor personal injury or property damage if the hazard is not avoided.
1. GENERAL
This user manual describes features and functions of the 84-Circuit DSX-1 Panels. The
1.01
manual contains a description of the panels and installation instructions.
The 84-Circuit DSX-1 Panels are designed to provide high density terminations with
1.02
efficient cable management. Various panel designs provide applications for Central Office, CEV,
Hut and Outside Plant cabinets.
The 84-Circuit DSX-1 Panel can terminate three 28-circuit M1/3 multiplexers on a
1.03
single panel. Eighty-four associated DS-1 network elements (digital switch, channel banks, etc.)
can be terminated on another panel and then cross-connects tie the two DS-1 circuits together.
The 84-Circuit DSX-1 Panel operating procedures are the same as other DSX-1
1.04
equipment and are covered in ADCs DSX-1 Operational Procedures - ADCP-80-322.
Page 2
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
2. DESCRIPTION
This section contains a functional, physical and technical description of the 84-Circuit
2.01
DSX-1 Panel.
A. Functional Description
DSX-1 equipment provides a centralized, equal level cross-connect point for digital
2.02
signals. The 84-Circuit DSX-1 Panel is a high density cross-connect termination panel. It
provides jack access for monitoring, testing and circuit patching. A typical DSX-1 circuit
diagram is shown in Figure 1. Circuit cross-connects are identified by flashing LEDs. Flexible
configurations are available for front or rear cross-connect arrangements. The Input/Output
terminations are available with wire-wrap pins or 64 pin Amp connectors. Two circuit labeling
schemes, 1-84 or 1-28 A, B, C are available.
-48V
-48V
SHIELD GROUND
GROUND
SHIELD GROUND
GROUND
MON
OUT
IN
MON
OUT
IN
OUT
OUT
T
R
T
R
DIGITAL
EQUIPMENT
IN
OUT
TL
TL
OUT
TN
RN
TN
RN
TN
RN
TN
RN
T
R
T
R
IN
DIGITAL
EQUIPMENT
IN
IN
1409-A
2.03
Front Cross-Connect
x
Front Cross-Connect Panels provide jack access and cross-connect terminations on the
front of the panel. Both patching and cross-connects are made on the front of the panel.
Front Split Cross-Connect Panels have the cross-connect field split evenly on the left and
right side of the panel. See Figure 2. The cross-connect jumpers are distributed evenly to
both the left and right wire way, providing efficient cable management when full bays of
84-Circuit DSX-1 Panels are used in a central office.
Page 3
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
JACKFIELD
CROSS-CONNECT FIELD
TL
OUT TN
RN
IN
14
T
L
14
TN
RN
FRONT
1
14
14
TL
OUT T
R
IN T
R
A
1
14
T
L
T
L
14
14
15
28
TL
T OUT
R
T
IN
R
A
15
28
TL
OUT T
R
IN T
R
15
28
B
1
28
15
T
L
T
L
14
TL
OUT T
R
IN T
R
15
TL
T OUT
R
T
R IN
28
B
15
28
TL
T OUT
R
T
R IN
JACKFIELD
SPLIT CROSS-CONNECT FIELDS
CROSS-CONNECT
CABLE RINGS
REAR
1
10
11
GROUP A CIRCUITS
15
20 21
25
28
T
OUT R
IN
-48V GND
1
T
R OUT
T
R
T
R
SG CG
10
11
10
IN
GROUP B CIRCUITS
15
20
21
25
IN
28
T OUT
R
T
R
T
R
GROUP C CIRCUITS
15
20 21
25
IN
28
T
OUT R
T
R OUT
T
R
IN
11
T
OUT R
T
R
IN
1410-A
Left Side Cross-Connect Panels have the cross-connect field on the left side of the panel.
See Figure 3. This panel is designed for outside plant or hut applications where the
ultimate requirement will not exceed eight 84-Circuit DSX-1 Panels. The Left Side
Cross-connect Panel is not recommended when a full seven foot bay of DSX is required.
Jumper build-up would cause congestion in the wire way.
14
15
IN
T
R
T
R
A
1
IN
15
IN
28
14
T
L
T
L
14
TL
T
R
T
R
OUT
IN
B
1
IN
OUT
A
14
14
15
28
TL
TL
OUT
14
TL
T
R
TL
OUT
28
TL
OUT
T
R
T
R
15
28
15
15
T
L
OUT
IN
28
T
L
28
CROSS-CONNECT FIELD
JACKFIELD
Page 4
1998, ADC Telecommunications, Inc.
1411-A
ADCP-80-329
Issue 2, September 1998
CEV/Total Front Access Panels have all the Input/Output terminations, cross-connect
terminations, jacks and power lugs on the front. See Figure 4. This panel is used in
applications where rear access is prohibited, such as; CEVs or Huts where bays are
placed against the wall; Central offices where bays are placed back to back or against an
obstruction; OSP cabinets with front access only.
Combo Panels combine 84 DSX-1 terminations and three DS3 interconnect circuits on a
single panel. See Figure 5. This panel is typically used in Outside Plant cabinets where a
combo panel will terminate the incoming electrical side of a 150 MB Fiber Optic
Terminal or OC3 Sonet Terminal. This panel uses Minimum Point of Presence (MPOP)
interconnect which eliminates the need for a separate DSX-3 interface.
14
A
1
14
TL
OUTT
R
IN T
R
15
14
TL
OUTT
R
IN T
R
C
-48
GND
14
15
28
14
T
L
M
T
L
M
28
B
1
14
TL
OUTT
R
IN T
R
15
28
INPUT/OUTPUT FIELD
15
28
TL
T OUT
R
T IN
R
A
15
T
L
M
14
15
15
T
L
M
14
28
TL
T OUT
R
T IN
R
28
B
15
28
TL
T OUT
R
T IN
R
C
28
14
15
28
SG
CG
JACKFIELD
1412-A
Page 5
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
DS3 SECTION
IN
OUT
MON
IN
A
B
14
15
TL
OUT T
R
IN T
R
OUT
MON
28
14
15
15
14
15
28
TL
TL
T OUT
R
T
R IN
OUT T
R
IN T
R
14
IN
OUT
MON
MON
T
L
T
L
14
28
MON
I
TL
T OUT
R
T
R IN
OUT
B
OUT
28
IN
IN
14
TL
T OUT
R
T
R IN
TL
OUT T
R
IN T
R
MON
B
IN
OUT
15
28
15
T
L
T
L
28
DSX-1 JACKFIELD
OUT
REAR VIEW
MON
OUT
BNC
CONNECTORS
ACCESS
JACKS
A
IN
OUT
IN
MON
OUT
MUX
IN
IN
FOT
OUT
R3
A - OUT
IN
OUT
A
BNC
OUT
R2
L1
OUT A
MUX
FOT
OUT
R1
IN
A BNC
IN
B - OUT
IN A
L1
B - IN
BLOCK DIAGRAM
DS1 (28)
150 MB
FOT
DS3 (3)
DS3
MPOP
DS3 (3)
M1/3
MUX
DS1 (28)
84 CIRCUIT
DSX-1 PANEL
DS1 (28)
1413-A
Page 6
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
Rear Cross-Connect
x
Rear Cross-Connect Panels have the IN/OUT and cross-connect terminations on the rear
of the panel with jack access on the front. See Figure 6. This panel is typically used in
central offices with existing rear cross-connect panels.
1
14
14
T
L
15
28
T
L
14
15
28
15
T
L
T
L
28
1414-A
JACKFIELD
B. Physical Description
Separate 84-Circuit DSX-1 Panels are designed for mounting in 19 or 23 inch (48.3 or
2.04
58.4 cm) equipment racks and can be recessed 2, 3 or 4 inches (5.1, 7.6 or 10.2 cm). Panels are
available in putty white or black color. The chassis dimensions vary, as shown in Table 1.
The Jackfield, located on the front of the panel consist of space saving Bantam jacks and
2.05
LED tracer lamps. The Input/Output terminations are located on the rear except for Total Front
Access Panels. The terminations are wire-wrap pins and on some models can be 64 pin Amp
connectors. The Cross-connect section consists of wire- wrap termination blocks for connecting
DSX-1 circuits. The cross-connect section is on the front or the rear of the panel depending upon
the panel model. See Figure 7 for a schematic representation of a DSX-1 circuit diagram.
JACKFIELD
-48V
SHIELD GROUND
GROUND
MON
OUT
IN
TL
T
R
T
R OUT
T
IN
R
OUT
IN
T
R
CROSS-CONNECT
FIELD
DSX-1 CIRCUIT
DIAGRAM
INPUT / OUTPUT
FIELD
1323-A
Page 7
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
C. Technical Description
2.06
Table 1 lists the specifications for each available 84-Circuit DSX-1 Panel.
Table 1. 84-Circuit DSX-1 Panel Specifications
PARAMETER
SPECIFICATION
REMARKS
Rear Cross-Connect
Rear Cross-Connect
Front Cross-Connect
Panel Requirement
48 Vdc
LEDs
.008 Amp/LED
Contact Rating
Maximum
(Bantam Jacks)
40 dBm
Maximum
Physical
Dimensions (H u W u D)
Electrical
Environmental
Operating Temperature
40q F to +149q F
(40q C to +65q C)
Non-Operating Temperature
85q F to +185q F
(55q C to +85v C)
Humidity
0% to 95%
Non-Condensing
Operating/Non-Operating
3. INSTALLATION
Danger: To prevent electrical shock, never install telephone equipment in a wet location
or during a lightning storm. When installing or modifying telephone lines, disconnect
lines at the network interface before working with uninsulated lines or terminals.
Installation of 84-Circuit DSX-1 panels involves mounting of the panels in the various
3.01
bays and wiring them to the equipment. Each panel is shipped with an installation drawing. The
drawing defines the specific termination connections required to complete the wiring.
For full bay applications 5.0 inch (12.7 cm) spacers and upper and lower cable troughs
3.02
are recommended for proper cable management. Panels are installed from the bottom of the bay
up. Except for Total Front Access panels, the Out equipment cables run down the right side
(rear) of the bay. The In equipment cables run down the left side (rear) of the bay. See Figure 8.
Page 8
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
The maximum of Total Front Access panels installed in a bay is eight. The Out
3.03
equipment cables run down the right side (front) of the bay. The In equipment cables run down
the left side (Front) of the bay. Refer to Figure 8.
OUT EQUIPMENT
CABLES
IN EQUIPMENT
CABLES
CABLE TROUGH
FRONT OF BAY
IN EQUIPMENT
CABLES
OUT EQUIPMENT
CABLES
CABLE TROUGH
FRONT OF BAY
Page 9
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
A. Panel Mounting
Mounting brackets, cable rings and labels are packaged separately and installed on site.
3.04
The front cross-connect cable rings are installed at the same time as the panel is secured in place.
Rear cross-connect rings and the labels are installed after the panel is secured in place.
3.05
1.
Attach the mounting brackets onto each panel. Use special thread-forming screws
(provided) to achieve proper grounding. Tightened to a minimum of 8 inch/lb..
2.
Install the panels in the assigned bay locations using #12-24 mounting screws provided.
For Front Cross-Connect panels place the cable rings on top of the panel mounting
bracket, then insert the mounting screws.
3.
Install cable rings at the rear of the panel (for rear cross-connect models) using special
thread-forming screws as in step (1).
4.
Connect the 48V terminal on the panel to a NEG () terminal on the fuse panel (white
wire).
2.
Connect the GND terminal on the panel to the corresponding POS (+) terminal on the
fuse panel (black wire).
3.
Connect the CG terminal on the panel to the office frame ground (green wire). This is the
recommended chassis grounding procedure.
Note: The metal strap between the CG (Chassis Ground ) and SG (Shield Ground)
terminals on the module may be removed to isolate the shield ground from the chassis
ground.
Page 10
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
METAL
STRAP
BLACK WIRE
-48
GREEN WIRE
GND
-48V
GND
SG
CG
1417-A
Connect the IN T and R of the originating DSX-1 position to the OUT T and R of the
terminating DSX-1 position as selected in paragraph 3.12.
2.
Connect the OUT T and R of the originating DSX-1 position to the IN T and R of the
terminating DSX-1 position .
3.
Interconnect the tracer lead (TL) terminals of the originating and terminating DSX-1
units.
Page 11
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
5 CONDUCTOR
JUMPER WIRE
TWISTED PAIRS
TL
TN
OUT
RN
TL
TN
IN
CROSS-CONNECT
TERMINAL BLOCKS
RN
TN
RN
OUT
TN
RN
IN
1418-A
E. Cross-Connection Verification
3.14
1.
2.
Observe the tracer lamps. The tracer lamp above the monitor jack with the plug inserted
and the tracer lamp above the monitor jack of the cross-connected equipment will flash
for about 30 seconds and then remain lit.
3.15
The above procedure may be used, on an in-service basis, without service interruption.
4. OPERATION
The operating procedures for the 84-Circuit DSX-1 Panel are the same as all DSX-1
4.01
equipment. For step by step operating procedures, refer to DSX-1 Operational Procedures
ADCP-80-322.
5. MAINTENANCE
The 84-Circuit DSX-1 Panel maintenance requirements are minimal, consisting of
5.01
periodic cleaning and tracer lamp replacement.
Page 12
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
A. Preventative Maintenance
Panels should be cleaned during routine office equipment maintenance. Accumulated
5.02
dirt and film should be removed using a vacuum cleaner and clean soft brushes and cloths. Care
must be taken to prevent dust and dirt from getting into panel jacks.
B. Corrective Maintenance
Danger: All corrective maintenance should be performed with the 48 Vdc office
battery off or disconnected from the panel to avoid electrical shock.
5.03
1.
2.
3.
Page 13
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
Product Management
Project Engineering
Project Administration
Network Design
Broadband Design (RF Design and Strand Mapping)
Integration Network Testing
Network Monitoring (Upstream or Downstream)
Power Monitoring
Remote Surveillance
System Turn-Up and Test
Service/Maintenance Agreements
Technical Training
Product Technology
Custom Designed Training
Technical Operations
Detail Engineering
End-to-End Installation
Drafting Services
Technical Information
Technical Information
System/Network Configuration
Product Specification
Product Application
Training
Installation and Operation Assistance
Troubleshooting and Repair
Field Assistance
Sales Administration
Extension 3000
Quotation Proposals
Ordering
Delivery
General Product Information
Product information and service can also be obtained by accessing the ADC web site at
7.02
www.adc.com or by writing ADC Telecommunications, Inc., P.O. Box 1101, Minneapolis,
Minnesota 55440-1101, U.S.A.
Page 14
1998, ADC Telecommunications, Inc.
ADCP-80-329
Issue 2, September 1998
Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior
notice. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits
and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar
damages. This disclaimer of liability applies to all products, publications and services during and after the
warranty period.
This publication may be verified at any time by contacting ADCs Technical Assistance Center at 1-800-366-3891,
extension 3223 (in U.S.A. or Canada) or 612-946-3223 (outside U.S.A. and Canada), or by writing to ADC Telecommunications,
Inc., Attn: Technical Assistance Center, Mail Station #77, P.O. Box 1101, Minneapolis, MN 55440-1101, U.S.A.
Page 15