You are on page 1of 44

Created by HumanNetwork

http://f2atv.com

Rev 3

NFUSION STEP BY STEP FOR NEWBIES


Get your Nfusion Ready
Plug your NFusion to TV

CHECK BOOT VERSION

3
4

Connect NFusion to PC/Laptop


LOAD NEW BOOT BIN
LOAD THE LATEST SOFTWARE TO YOUR STB
CONNECT NFUSION TO TV AFTER LOAD S/W
CHECK BOOT AND S/W VERSION
FACTORY DEFAULT AFTER LOAD S/W
PROXY SETTING
EMULATOR
ANTENNA SETTING
MOTOR SETTINGS
HOW TO CHANGE PASSWORD
HOW TO SELECT INDIVIDUAL BIRD/TOTAL CHANNELS ON
EACH BIRD
MANUALLY UPDATE EPG
HOW TO LOCK CHANNEL
SETTING LOCAL AREA
STB PICTURES

5-7
8-9
10
11
12
13-14
15
16-22
23-29
30-31
32-33

34
35-38
38-39
40--44

Created by HumanNetwork

http://f2atv.com

Rev 3

Get your Nfusion Ready.


Before you do anything.. you should verify that your NFusion should have the following:
-

1. Receiver
1. Remote Control
1. Red/White/Yellow cable
1. RS232 NULL cable.
if you are lucky your dealer will included 1 4x1 switch.

Download loader 1.0 and latest S/w ie. 145.2 from file section. Make sure you unzip them otherwise it won't work

Plug your NFusion to TV

Video/Audio
Cable

Power

Created by HumanNetwork

http://f2atv.com

Rev 3

CHECK BOOT VERSION


After you connect your Nfusion to your TV
Turn Nfusion ON from Rear Switch
Press Menu key on your remote
This is what you should see on your TV screen

On the Menu Screen


1. Scroll down to "System Settings"
2. Press OK
3. Scroll down to "S/W Version"
4. Press OK
you will see the boot version,
if you BOOT R3X less than 1.28 then you need to load
boot 1.30 or later. if boot is "BOOT R3X 130" then you
go ahead and load the latest software on it. i.e 145.2
Press Exit
3

Created by HumanNetwork

http://f2atv.com

Rev 3

Connect NFusion to PC/Laptop


now connect your Nfusion to your computer or laptop to load bin and software. make sure you sue NULL cable that come with the box. do not
use any other cable if you are too sure.
if you use USB-RS232 make sure you have a correct driver.
if you BOOT R3X 128 or later then skip LOAD

NEW BOOT BIN on page 4.

otherwise you need to load latest boot on page 4.

RS232 NULL cable.


if you are using USBRS232. make you have
correct driver install.
Power
cable

Created by HumanNetwork

http://f2atv.com

Rev 3

LOAD NEW BOOT BIN

STEP1: Open N-Fusion loader v 1.0

Changed from
Main->Boot
STEP2: Click on Main>>it should change to Boot>>
STEP3: Click on Open File

STEP4: Browse to the newer boot file that you


need to load. once you found that highlight it then
click open

Created by HumanNetwork

http://f2atv.com

Rev 3

STEP5: Click on Start Nfusing button

STEP6: Press OK on your remote

STEP7: you need to recycle the main power


switch from the back of STB (Set Top Box)

once the STB came back on, software


automatically recognize your STB and it start to
upload the boot file.
6

Created by HumanNetwork

http://f2atv.com

Rev 3

keep an eye on you STB LED, it should display Good after bin
successfully write to your STB.

STEP8: Press OK after you've see Good on your STB.

I've seen so many ppl having problem loading boot, S/W via their pc. there are couple thing you have to keep in mind. make sure you use
NULL cable came with nfusion box.. do not use different cable, even though it look similar, especially for those who owned different stb
that use straight cable.
USB-Rs232 adaptor, this is the major issue that pple having with.. you have to make sure you load driver b4 you do anything else.. and
make sure the port that your USB-RS232 is not taken by other devices.

To load S/W, leave your NFusion remain connected to your PC


To check boot version after loaded new boot, please refer back to "Check Boot Version"

Created by HumanNetwork

http://f2atv.com

Rev 3

LOAD THE LATEST SOFTWARE TO YOUR STB


Open N-Fusion v 1.0 Loader
Click on Open File

Browse to the file that you want to load, in this example we


load v145.2
Click on the file then click Open

Leave everything as default


Click on Start NFusing

Created by HumanNetwork

http://f2atv.com

Rev 3

Press OK
Now turn off the main power switch from the back of your STB
then turn it back on.

Once the STB came back on the loader automatically detect


your STB and it start to upload the software to your STB

Keep an eye on your STB you should see the number on LED
incrementing 1 at a time. once you see Good on your STB, it
safe to click OK on your Loader

at this point you can disconnect your Nfusion from your computer. and connect it to your TV.
9

Created by HumanNetwork

http://f2atv.com

Rev 3

CONNECT NFUSION TO TV AFTER LOAD S/W

Video/
Audio

RG6

Power

Connect RJ-45 cable from your router to the back of your STB.
Hardwire, or connect to your wireless adaptor

10

Created by HumanNetwork

http://f2atv.com

Rev 3

CHECK BOOT AND S/W VERSION

Once you connect Nfusion to your TV, you should see MAIN
MENU display on your TV screen. if not Press Menu on your
remote
Scroll down to System Settings then press OK
Input your default password 0000

Scroll down to S/W Version then hit OK on your remote key.

Now you should see new Boot and S/W


You are successfully loaded software to your STB

11

Created by HumanNetwork

http://f2atv.com

Rev 3

FACTORY DEFAULT AFTER LOAD S/W

Menu->System Setting
password 0000

Scroll down o Factory Default press OK


STB should be reboot after you hit OK .

12

Created by HumanNetwork

http://f2atv.com

Rev 3

PROXY SETTING
By default Proxy is turn off after you load new S/W. but just incase you want to use proxy here is the guide.
For best practice, I would recommend you to change your proxy server at least once every couple of weeks. It is not a good idea to connect to only
one proxy for ever.

To get to proxy screen


Menu->Internet->Proxy Connection
Press OK

On the same screen.


Turn the Proxy ON
Input the proxy server IP that you want to use.
You need to put exactly what port that server use.
in this example i use the following
IP: 148.233.159.58
Port: 0080
Press Exit when you done
if you got the right proxy server, your stb should
display picture in ~5sec after you pressed EXIT

13

Created by HumanNetwork

http://f2atv.com

Rev 3

Here is the list of working proxy and port.. you can use one of this in the list or find your own if you prefer. if you find one that cause a lot of
freezing. then change to a different one.
PROXY SERVER IP

PORT

TYPE

COUNTRY

218.206.074.075

0080

transparent

China

193.093.104.101

8080

transparent

Poland

148.233.159.058

0080

transparent

Mexico

163.030.000.006

0080

transparent

Taiwan

083.238.044.008

8080

transparent

Poland

082.114.070.0098

8080

transparent

Czechoslovakia

124.133.037.247

8080

transparent

China

060.217.228.199

0080

transparent

China

For more proxy list go to http://www.publicproxyservers.com/index.html

What is Proxy?
proxy server is a server (a computer system or an application program) which services the requests of its clients by forwarding requests to other
servers. A client connects to the proxy server, requesting some service, such as a file, connection, web page, or other resource, available from a
different server. The proxy server provides the resource by connecting to the specified server and requesting the service on behalf of the client.

14

Created by HumanNetwork

http://f2atv.com

Rev 3

EMULATOR

If you want to use IKS then it is very critical that you have to
run EMULATOR = OFF.
Emulator= off meaning your using IKS server which is your
Nfusion required connect to internet while viewing TV.
Emlator = ON meaning it is using stand alone bin.
I would recommend you to use IKS that way you can avoid
ECM. let the server do the hard work :)
Menu->User Settings->Emulator

15

Created by HumanNetwork

http://f2atv.com

Rev 3

ANTENNA SETTING

110W and 119W stationary dish. in this example we going to use Single LNB type and DiCEqC 1.0/1.2.
I assumed that your physical dish properly setup. if not please setup your dish before doing the following steps.

STEP1: Press Menu key on your remote


Press OK on your Remote control key

STEP2: Input password 0000


0000 is the default password for nfusion

16

Created by HumanNetwork

http://f2atv.com

Rev 3

STEP3: Press OK on Antenna Setting

STEP4: Satellite is highlight, Press OK on your remote control

17

Created by HumanNetwork

http://f2atv.com

Rev 3

STEP5: Press double arrow down key on your remote until you see
110.0W ECHOSTAR 8/1 then press OK on your remote control.

LNB Type
= 1. Standard
LOFreq
= 11250
22KHz
= OFF
DiSEqC Mode = Port 2 (I used port 2 for 110. set this
according to your physical port setting.)
Multi-Dish Switch
= Disable
Motor Settings
= OFF
LNB Power
= ON
you should see EchoStar 110 banner popup on your
screen. S and Q also have green bar.
S = Signal
Q= Quality.
we are not too concern about the Q. we more concern
about S. The higher the S is better.
if you own other STB you might see their signal better
than NFusion, but I won't worry about it if I were you.
as long as your dish setup properly.

18

Created by HumanNetwork

http://f2atv.com

Rev 3

STEP6: Now press Menu once on your remote control.

STEP7: Press OK on your remote control to save.


STEP8: Press OK on your remote control again to get
back into Antenna Setting

19

Created by HumanNetwork

http://f2atv.com

Rev 3

STEP9: Scroll down to Search Channels CH All Search


then press OK to search auto scan 110W.

STB scanning the selected bird.


sit back and watch the channels coming through :)

20

Created by HumanNetwork

http://f2atv.com

Rev 3

Once Auto Scan is done STB automatically update itself and it


will automatically exit itself.

Screen after scanned.

21

Created by HumanNetwork

http://f2atv.com

Rev 3

SETUP 119W

Repeat the same process as 110W. The only difference is your


PORT setting. Change the port setting to correspond with your
physical setup.
LNB Type
= 1. Standard
LOFreq
= 11250
22KHz
= OFF
DiSEqC Mode = Port 3 (I used port 3 for 119. set this
according to your physical port setting.)
Multi-Dish Switch
= Disable
Motor Settings
= OFF
LNB Power
= ON

22

Created by HumanNetwork

http://f2atv.com

Rev 3

MOTOR SETTINGS
I'm assuming that you have your physical motor setup at this point. you also should know your Long and Lat. if you don't you can google
your zip and it will tell you exactly what that is.
in this walkthrough, we are going to use 82.7W longitude and 27.8N for latitude.
I'm going to aim 91W for this walkthrough.

STEP1: Press MENU on your remote control.


STEP2: Press OK on your Remote control

23

Created by HumanNetwork

http://f2atv.com

Rev 3

STEP3: input password 0000

STEP4: Press OK on Antenna Setting

24

Created by HumanNetwork

http://f2atv.com

Rev 3

STEP5: Satellite is highlight, Press OK on your remote


control

STEP6: Press double arrow down key on your remote


until you see 91.0W NIMIQ1 KU then press OK on your
remote control.

25

Created by HumanNetwork

http://f2atv.com

Rev 3

LNB Type
= 1. Standard
LOFreq
= 11250
22KHz
= OFF
DiSEqC Mode = Port 1 (I used port 1 for 91W and all of my
Circular birds, and port 4 for my Linear birds. set this according to
your physical port setting. motor is a little bit different from
stationary dish. all of the C birds share a common port vs L birds.)
Multi-Dish Switch
= Disable
Motor Settings
= Usals (press vol key on your remote to
cycle thru)
LNB Power
= ON
STEP7: Press OK on Motor Settings = Usals

STEP8: Press Ok. Now input your Long/Lat, use your keys on the
remote to input the value.
My Longitude = 082.7W
My Latitude
= 27.8N
Press Vol key to select (W/E or N/S)

26

Created by HumanNetwork

http://f2atv.com

Rev 3

Once you input the value correctly scroll down to Goto Sat
Position
STEP9: Press OK.
you won't see the motor moving, just wait for ~30sec you
should see S&Q are green and NIMIQ1 also lock.

STB locked your selected SAT

27

Created by HumanNetwork

http://f2atv.com

Rev 3

STEP10: Press Menu on your remote to return to a


previous screen.

STEP11: Press Menu on your remote to save the Sat


posistion.
STEP12: Press OK to save.

STEP13: Antenna Setting is highlight, Press OK

28

Created by HumanNetwork

http://f2atv.com

Rev 3

Now you see that your STB locked 91W


STEP14: Scroll down to Search Channels then press OK to
auto search on 91W

Now kick back and relax, your STB is scanning 91W.


once it done scanning it will automatically update itself.

That is how you set your motor with NFusion STB.


you only need to input Long/Lat once. To set another bird
using motor repeat STEP1 - STEP14, except STEP8:

29

Created by HumanNetwork

http://f2atv.com

Rev 3

HOW TO CHANGE PASSWORD

Press Menu on your remote


Scroll down to User Settings then Press OK

Scroll down to Parental Control then press OK

30

Created by HumanNetwork

http://f2atv.com

Rev 3

Input your password (default password is 0000

Scroll down to New Password enter your


new password and Confirm New
make sure they both identical.

31

Created by HumanNetwork

http://f2atv.com

Rev 3

HOW TO SELECT INDIVIDUAL BIRD/TOTAL CHANNELS ON EACH BIRD

Press GUIDE key on your remote


Press AUDIO key (green)

On the left you should see the list of your birds. In this case
119.0W and 91.0W
On the right you should see total of your channels on each
birds.

32

Created by HumanNetwork

http://f2atv.com

Rev 3

MANUALLY UPDATE EPG

Press GUIDE key on your remote


Press LANG key (blue)

Your EPG is updating

This is what it should look like after it done.

33

Created by HumanNetwork

http://f2atv.com

Rev 3

HOW TO LOCK CHANNEL

Press MENU on remote control


Scroll down to Edit TV/Radio List
Press OK

Enter your password, default password is 0000

Scroll down the channel you want to lock then press


OK.
you should see the lock symbol appear on the
selected channels.

34

Created by HumanNetwork

http://f2atv.com

Rev 3

When done lock your channel.


Press MENU button on your remote.
Press OK to save

HOW TO ADD CHANNELS TO FAV GROUP

Press MENU key on your remote.


scroll down to Edit Favorite List
Enter Password (0000 default password)

35

Created by HumanNetwork

http://f2atv.com

Rev 3

Press right vol key on your remote to


press OK rename your favorite group.

Once you've done your group name.


press MENU key go get back previous screen

36

Created by HumanNetwork

http://f2atv.com

Rev 3

To add Favorite channel.


press left vol key to
now scroll down the your fav channel then press OK.
once you've done press Menu key to get out.

Press OK to save.
repeat the same process for another favorite group.
you can add up to 8 favorite groups.

37

Created by HumanNetwork

http://f2atv.com

Rev 3

SETTING LOCAL AREA

Press MENU key on your remote.


scroll down User Settings
Press OK

Local Area is highlight, Press OK

38

Created by HumanNetwork

http://f2atv.com

Rev 3

Scroll down to you State.


Press right VOL key once to select your city

Select your city, Press OK

Press OK to save your local area

39

Created by HumanNetwork

http://f2atv.com

Rev 3

STB PICTURES

40

Created by HumanNetwork

http://f2atv.com

Rev 3

41

Created by HumanNetwork

http://f2atv.com

Rev 3

42

Created by HumanNetwork

http://f2atv.com

Rev 3

43

Created by HumanNetwork

http://f2atv.com

Rev 3

44

You might also like