Professional Documents
Culture Documents
Die casting is a moulding process in which the molten metal is injected under high pressure and
velocity into a split mould die. It is also called pressure die casting. The split mould used under
this type of casting is reusable. Die casting is categorized two types namely- hot chamber and cold
chamber as shown in Figure M2.3.1. Metals like Zinc, tin and lead alloys are casted in hot chamber
die casting having melting point below 3900C whereas aluminum alloys are casted in cold chamber
die casting machine. Aluminum dissolves ferrous parts in the die chamber and hence preferred to
be used in cold chamber die casting. Continuous contact of molten metal is avoided by using a
ladle for introducing molten metal directly to the machine.
4. Ability to make many intricate parts such as hole opening slot trademark number etc.
5. Much thinner wall sections can be produced which cant be produced by other casting
methods.
6. Varieties of alloys can be used as per design requirements. For example zinc can be used
for intricate forms and plasticity, aluminum for higher structural strength, rigidity and light
weight.
3. Hollow shapes are not readily casted because of the high metal pressure.
4. Limited sizes of the products can be produced based on the availability of the equipment
Die casting process is preferred for nonferrous metal parts of intricate shapes. Examples of
products are automobiles appliances, hand tools, computer peripherals, toys, optical and
photographic equipment etc.
Since dies are made from tool steel, for die casting products lower melting point nonferrous
materials are used. Popular among them are aluminum and zinc alloys. In recent days, ferrous
metal die casting is carried out on an experimental basis. Also on limited production basis, dies
with refractory material are used for materials having high melting temperature of about 17000C.
Different material properties of various types of alloys are shown in Table M2.3.1.
Table M2.3.1: Various types of alloys recommended for die casting (Source: Design for
Manufacturability Handbook by James G Bralla, 2nd Ed)
1. Identify the possibility of incorporating several functions in to one die casting. Full
advantages must be taken for the reduction of machining that die casting can afford.
2. Before the design and construction of die begin the designer should finalize the design of
die casted product and its producibility. Dies after machined undergo heat treatment for
hardening.
3. The designer must consult die cater about the location of the ejector pin as early as possible
in the product design stage itself. If the impression left by the pins are not tolerable or cant
be cored out, as an alternative solution rings or sleeve ejection can be opted.
4. Abrupt section changes, sharp corners and wall at an acute angle to one another need to be
avoided. These features disturb the continuity of metal flow and lead to form a porous
structure and surface irregularities. Therefore, it is recommended to provide radii as
generous as possible with differing sections blending into one another.
5. Blind recesses are needed to be provided in the die to form bosses. Due to trapped air
subsurface porosity is developed and this causes the drills to wander and taps to break in
secondary machining and hence recommended to be avoided.
Wall thickness: Sharp changes in sectional area and heavy sections over 6 mm thickness should
be avoided if possible. Uniform wall thickness need to be maintained so as to achieve a minimum
porous die casted product. The injected liquid metal cools rapidly on contact with the die casting
surface resulting in a fine grained dense structure (the surface is termed as skin) generally devoid
of porosity and is considered to be the strongest region of the die casted product. Depending upon
the casting size, the recommended skin measures between 0.38 and 0.63 as mentioned in the Table
M2.3.2.
Table M2.3.2: Recommended wall thickness (mm) (Source: Design for Manufacturability
Handbook by James G Bralla, 2nd Ed)
Figure M2.3.2: To avoid surface shrinks, connect the boss to the wall with a short rib.
During cooling process, due to shrinkage in the metal inside the boss even after the cooling of the
adjacent walls, bosses behind the surface can cause visible sinks on decorative parts having flat,
expansive areas. Sink effects are magnified in thinner walls. To avoid such surface shrinks the
bosses are relocated and connected to the wall with a short rib as shown in Figure M2.3.2.
Ribs and fillets: Ribs are provided for structural reinforcing. It must be perpendicular to the parting
line so as to allow the removal of casting from the die. In order to avoid sink, it is recommended
that the width of the rib should not exceed the wall thickness of the casting. The minimum distance
between the two adjacent ribs must be the sum of their heights. Sufficient (at least 20 per side)
drafts should be provided to help in ejection. Ribs and fillets are also used to improve the rigidity
and strength of the standing bosses. Ribs can be designed on both the halves of the die instead of
providing on one side of the wall, thereby strengthening it avoiding local thickening effect. In
case, ribs are designed to cross, they should do so at right angles. Acute angle intersections are
avoided because it causes the die to overheat in the area between the ribs. (Figure M2.3.3 to
M2.3.6)
Undesirable Desirable
Figure M2.3.3: Incorporating internal ribs for Box-shaped components and provide radius for
corners
Undesirable Desirable
Draft: The side wall of the die casting and other features perpendicular to the parting line must be
tapered or drafted as much as possible to easy removal from the die. Draft angles depend upon the
type of alloy is used and draft requirements have been provided in Table M2.3.3. For the case of
outside wall, the recommended draft angel should be the half of the draft angle used in the inside
wall.
Table M2.3.3: The recommended draft angel for inside wall (in degree)
Depth of wall Copper alloys Aluminum alloys Magnesium alloys Zinc alloys
(mm )
0.250.50 18 16 13 10
0.501.0 14 12 10 7
1.02.0 10 8 7 5
2.03.8 7 6 5 3.5
Radii: Sharp internal corners in die casting are to be avoided. The various reasons for avoiding sharp
corners are: stress concentration at the corner, subsurface porosity due to abrupt change in metal
flow direction during injection, and premature erosion of the die material because of heat
concentration at sharp corners. It is recommended that radii and fillets should be 1.5 times the wall
thickness for both inside and outside radii. (See Figure M2.3.7)
Figure M2.3.7: Allow generous radii at internal and external corners.
Holes: The die-casting process uses cores to produce holes or openings. However, the cores used to
create hole are to be placed at right angles to the parting line and there are core length limits that
should not be exceeded depending upon the diameter. Sufficient draft should be provided to the
cores to ensure longevity (Refer Table M2.3.4 & Table M2.3.5). (Figure M2.3.8 to M2.3.9)
Table M2.3.4: Draft provided for different material a/c to diameter of hole.
3 4 5 6 10 13 16 19 25
Copper 13 25 32 50 90 125
Undesirable Desirable
Undesirable Desirable
Figure M2.3.9: Core slides can be avoided by using this hole design.
Draft,
Magnesium
Depth of hole, mm Copper alloys Aluminum alloys Zinc alloys
alloys
1.52.5 11 10 8 6
2.55 9 8 7 4.5
510 7 6 5 3
Undesirable Desirable
Threads: External screw threads can be formed on die casting but not for a precision fit. Production
of threads by machining is recommended for precision type of fit. The most practical way to cut the
threads are between the die halves and eject the part in normal manner. Due to accuracy reasons,
pitches finer than 24 threads per inch for Aluminum and Magnesium and 32 threads per inch for
Zinc are not recommended. In fact, it is possible to die cast internal threads either by unscrewing the
casting from the threaded core or rotating the core out of the casting during ejection. Zinc is
recommended for this type of design since other alloys shrink more tightly onto the core.
Inserts: Inserts can be incorporated into die casted parts where necessary. The most common type
of insert is the threaded stud used for assembly operation. It must be designed in such a manner that
material will shrink on to its shank with sufficient force thereby preventing the movement in use.
(Figure M2.3.11)
Undesirable Desirable
Flash and gate removal: A well-built trimming die generally removes flash almost to the most
extremely drafted point of the casting wall. In order to avoid the wear of the cutting edges certain
allowances must be provided. Commercial die castings are considered to be adequately trimmed if
flash and gates are removed to within 0.38mm of the casting wall. In case of very heavy gates having
size more than 2.2mm thick, gates are removed within 0.75mm. Angled junctions of an external wall
are avoided with parting line. It is preferable to add a minimum draft shoulder at the parting line.
(Figure M2.3.13)
Surface design: Large plain area is generally not advisable because, any slight casting imperfection
will be readily visible. Recommended option to resolve this issue is to mask irregularities by
designing in ribs, serrations or mould texturing.
The main cause of dimensional variation in die casting are due to the thermal expansion of both the
die and the casting. For designing die, a shrink factor of 0.6% is provided for both the contraction
and expansion mentioned above. Recommended tolerances for die casting by cavity dimensions in
either half of the die is shown in Table M2.3.6.
Table M2.3.6: Recommended tolerances for die casting by cavity dimensions in either half of the
die.