Professional Documents
Culture Documents
INSTALLATION GUIDE
Copyright
TSI Incorporated / 20042012 / All rights reserved.
Address
TSI Incorporated / 500 Cardigan Road / Shoreview, MN 55126 / USA
Fax No.
(651) 490-3824
iii
Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY AND
LIABILITY, which contains the complete and exclusive limited warranty of Seller. This
LIMITATION OF WARRANTY AND LIABILITY may not be amended, modified or its terms
waived, except by writing signed by an Officer of Seller.
Service Policy
Knowing that inoperative or defective instruments are as detrimental to TSI as they are to
our customers, our service policy is designed to give prompt attention to any problems. If
any malfunction is discovered, please contact your nearest sales office or representative,
or call TSI's Customer Service department at (800) 874-2811 (USA) or (001 651) 490-
2811 (International) or visit www.tsi.com.
Trademarks
TSI, TSI logo, DustTrak, VelociCalc, Q-TRAK, AeroTrak, SidePak, and TrakPro are
trademarks of TSI Incorporated. Windows and Windows Vista are registered
trademarks of Microsoft Corporation.
iv
CONTENTS
Introduction ........................................................................................ 1
TrakPro Software Installation ....................................................... 2
Driver Installation for DustTrak II/DRX Aerosol Monitor.............. 12
For Windows 7 Operating System ............................................. 12
For Windows Vista Operating System ....................................... 14
For Windows XP Operating System .......................................... 18
Setup Radio Modems (optional accessory) .................................. 24
Radio Modem Installation in Windows Vista Operating
System ......................................................................................... 24
Setup Radio Modem Configuration Software for Windows
Vista Operating System ............................................................. 29
Radio Modem Installation in Windows XP Operating System... 36
Setup Radio Modem Configuration Software for
Windows XP Operating System ................................................ 41
USB Hardware Setup for SidePak Monitor.................................... 46
For Windows 7 Operating System ............................................. 46
For Windows Vista Operating System ....................................... 47
USB Bus Installation ............................................................. 47
USB Port Installation ............................................................. 49
For Windows XP Operating System .......................................... 51
USB Bus Installation ............................................................. 51
USB Port Installation ............................................................. 55
Install Verification ........................................................................ 59
USB Driver Setup for VelociCalc/Q-TRAK 7575 Instruments .. 62
For Windows 7 Operating System ............................................. 62
For Windows Vista Operating System ....................................... 63
For Windows XP Operating System .......................................... 65
Install Verification ........................................................................ 69
v
(This page intentionally left blank.)
vi
Introduction
The following guide has been developed for installing TrakPro Data
Analysis software. The TrakPro software can be installed on
Windows 7, Windows Vista, or XP operating systems. To install this
software, you need administrative rights on the computer.
The USB install has been combined with the TrakPro software
installation. As part of the software installation, the USB driver files
are placed in the required directories. The MSCAL.OCX file for the
calendar control is also added and registered to prevent error
generation on selecting pump settings menu for SidePak monitor
with sampling pump.
The install has been simplified so that you only need to click the
Next > button on each dialog. The displayed screens are examples
only and may differ from the screens on your computer.
1
TrakPro Software Installation
Notes:
If you installed a previous version of TrakPro software, it is highly
recommended that you uninstall the previous version before
installing the new version of TrakPro software.
Install TrakPro software before connecting a TSI instrument to
your PC.
At this point, you have installed TrakPro software and the USB
driver files, and registered the calendar control file.
4. Expand the Network adapters tree and confirm the entry for TSI
USB Remote NDIS The entry should not have a yellow
exclamation mark. If there is an error, select the entry, right-click
and select the Update Driver in the popup box. Repeat the USB
install process following the on-screen directions.
10. Expand the Network adapters tree and confirm the entry for TSI
USB Remote NDIS The entry should not have a yellow
exclamation mark. If there is an error, select the entry, right-click
and select the Update Driver in the popup box. Repeat the USB
install process following the on-screen directions.
2. Select No, not this time and then click Next. The following
screen will be displayed:
9. Expand the Network adapters tree and confirm the entry for TSI
USB Remote NDIS The entry should not have a yellow
exclamation mark. If there is an error, select the entry, right-click
and select the Update Driver in the popup box. Repeat the USB
install process following the on-screen directions.
After the first round of installation, a new Hardware Wizard screen will
popup. Follow these steps to install the COM port driver.
The following screens appear once you plug the SidePak aerosol
monitor USB cable into the computer. The USB install has two parts:
1. Install USB bus
2. Install USB port
The screens for the bus and port installation are similar. The install
has been simplified so that you only need to click the Next > button
on each dialog.
This confirms that the calendar control file was successfully installed
and registered.
In the Pump Clock Time section, verify the correct time is displayed
and the pump time can be updated.
3. Click the Install this driver software anyway button. The setup
will start executing.
2. The install has been simplified so that you only need to click the
Next > button on each dialog.
At this point, you have installed the USB driver. You are ready to use
TrakPro software with the supported instruments.