Professional Documents
Culture Documents
BUILDERS
METALWORK
Welcome to this latest guide
from Expamet the brand you
can always rely on
The famous Birtley and Expamet brands are now working together
within Birtley Group. A combined strength which is adding value to
projects across the UK through quality, innovation and higher service
levels than ever before.
Thats Birtley Group commitment.
www.birtleygroup.co.uk
CONTENTS
10 Restraint Straps
12 Joist Struts
13 Truss Clips
14 Framing Anchors
15 Angle Plates
16 Angle Brackets
19 Timber Connectors
20 Splice Plates
Design Features
Single-piece, non-welded 75mm load bearing surfaces.
construction.
All hangers 150mm deep and
Wider masonry flange to over are manufactured 10mm
increase loadings on masonry of less to allow for notching and
compressive strength 2.8N/mm2 regularisation of timber joists.
and greater.
Gusset nail holes are
Manufactured from 2mm thick non coaxial.
pre-galvanized mild steel to
Standard available widths 38,
BSEN10346 : 2009,DX51D +
44, 47, 50, 63, 75, 89, 100, 125,
Z600.
150mm.
Installation Requirements
The back face of hanger must It is recommended that joists
be flush against the wall. are notched for the base of the
The timber joist should be hanger toachieve a level
square cutand butting to surface for plasterboarding.
the back face of thehanger Type R and ST provide
(maximum permitted gap6mm). additional location and
A minimum height of 675mm of alignment during construction.
set masonry must be in position HD Restraint Straps must be
above thesupporting flange used with all types of SPH joist
before any loadis applied. hangers if lateral restraint is
Fixing: Nail to the joist through required.
the nail holes ineach side gusset
with BAT 3.75 x30mm long
square twisted sherardised nails.
4
SPH JOIST HANGERS
TYPE S
Please state dimensions of joist
depth
width e.g. SPHS22550
Minimum box quantity
dependent on hanger size.
Return type R
TYPES R & ST
(made to order)
Please state dimensions of joist
depth
width
top flange (to suit wall width)
e.g. SPH22550R100
Quantity made to order
Straddle type ST
Design Features
Manufactured from pre-galvanized Nail hole diameter: 4.5mm
mild steel to BSEN 10346 : 2009, Bolt hole diameter: 14mm
DX51D + Z275.
Available widths: 38, 47, 50, 63,
Available in 7 types: 75, 100mm (122 + 150 for
MS240,335,380 - 1.2mm thick MS500, 560+ 620 only)
MS440,500,560,620 - 1.5mm thick
Installation Requirements
Fixing: use BAT 3.75 x 30mm long M12 Bolts or coach screws as
square twisted sherardised nails. specified by fixing manufacturer.
How to Order/Specify
1. Joist dimensions: Double joist depth and add joist width, ie for joist
225 deep x 38mm wide then: 225 (d) + 225 (d) + 38 (w) = 488mm.
2. The Maxi Speedy blank length must be lessthan total calculated
instep 1, therefore select MS44038 (not MS500 as the joist hanger
would stand proud).
6
MAXI SPEEDY JOIST HANGERS
7
SPEEDY JOIST HANGERS
Design Features
Speedy Hangers: 0.9mm thick
pre-galvanized mild steel to
BS EN 10346 : 2009, DX51D +
Z275. Hole diameter: 3.8mm.
LLS: 1.5mm thick material.
SGTS: 1.2mm thick material.
Girder/Girder Speedy: Fixing: use BAT 3.75 x 30mm long
3mm thick mild steel galvanized square twisted sherardised nails
to BS EN 1461. Hole diameter: through all available nail holes.
22mm.
Speedy joist hangers available sizes
Joist 38 44 47 50 63 75 80 91 100 105 120 155 Maximum
Width Joist Depth
SM 100
SL 175
ST 225
SGTS N/A
LLS 225
GGTS N/A
Characteristic load capacity Fk (kN) C24 Timber
Joist Width 38 44 47 50 63 75 91 100
Speedy Minor | SM 3.2 2.2 2.2
Short Leg Speedy | SL 6.3 4.6 4.6 5
Standard Leg Speedy | ST 8.5 7 6.7 6.7 6.9 7.1 7.1 7.4
Speedy Girder Truss Shoe | SGTS 10.7 12.3 12.8 12.6 11.2
Long Leg Speedy* | LLS 7.6 7.6 7.6 7.6 7.6 7.6 9.6
*6.7 kN when underslung by up to 100mm
8
SPEEDY JOIST HANGERS
9
RESTRAINT STRAPS
Design Features
The straps are manufactured
from pre-galvanized steel strips
to BS EN 10346 : 2009, DX51D
+ Z600 or stainless steel to
BS EN 10088-1 : 2014 : 1.4301.
Nominal Dimensions
Heavy Duty - 27.5 x 4mm
Standard - 27.5 x 2mm
Installation Requirements
Installation must comply Fixing for horizontal restraint:
with Building Regulations, 5 no 4 x 75 round wire nails
P06697 and BS 8103 : 1 per noggin, 1 per joist.
Part 1, as well as NHBC
recommendations. Fixing for vertical restraint:
Wallplate - 2 no 3.75 x 30
If straps are fixed across joists or square twisted nails.
trussed rafters which are parallel Blockwork - 4 no M5 x 50
with the wall, and there is a gap wood- screws into nylon wall
between the wall and the first plugs, one of which within
joist or truss, the gap must be 150mm from the bottom. For
packed. Noggins must be used stainless steel straps, stainless
between each joist or truss. steel fixings must be used.
10
RESTRAINT STRAPS
How to order
Ordering Example
(to order the strap shown above)
11
HERRINGBONE JOIST STRUTS
To suit joists
150 - 225mm.
HJS400
Joist Centres: 400mm
Length: 480mm
HJS450
Joist Centres: 450mm
Length: 523mm
HJS600
Joist Centres: 600mm
Length: 660mm
Specification:
Manufactured from 0.9mm thick Hole diameter: 4mm
pre-galvanized mild steel to Qty per box: 50
BS EN 10346 : 2009,
DX51D + Z275.
Installation Requirements:
Joist Span 2.5m to 4.5m Recommended fixing:
1 Row at mid span BAT 3.75 x 30mm long square
twisted sherardised nails.
Greater than 4.5m
2 Rows at 1/3 span positions
12
TRUSS CLIPS
TC38
for 38mm trusses
TC50
for 50mm trusses
Specification:
Manufactured from 0.9mm thick Overall height: 117mm
pre-galvanized mild steel to Overall width: 114mm
BS EN 10346 : 2009, Hole diameter: 4mm
DX51D + Z275. Qty per box: 200
Installation Requirements:
Use BAT 3.75 x 30mm long Uplift - 38mm - 2.7 kN
square twisted sherardised nails. Uplift - 50mm - 1.6 kN
All nail holes must be filled. The timber wall plate must be
securely held down onto the
Characteristic load bearing
supporting masonry.
capacity (Fk) :
13
FRAMING ANCHORS
BAT Multi-Grip
Framing Anchors offer the
most effective and economical
method of providing strong,
mechanical joints for framing
of timbers.
MFAAL / MFAAR
(left and right handed versions)
MFAAL & MFAAR
for anchoring rafters and trusses
to wall plate.
MFAC
for right or left handed use for
anchoring joists to beams, stringers MFABL / MFABR
to headers and hip joints. (left and right handed versions - MFABR shown)
Specification:
Manufactured from 0.9 mm thick
pre-galvanized mild steel to
BS EN 10346 : 2009,
DX51D + Z275.
Overall height: 127mm
Overall width: 38mm
Hole diameter: 3.8mm
Qty per box: 200 MFAC
Installation Requirements:
Always use in pairs to
prevent eccentric loading.
Recommended fixing:
BAT 3.75 x 30mm long
square twisted sherardised
nails.
Fixings should be used in all
available timber facing holes.
14
ANGLE PLATES
AP30030
Steel beam
50mm
min
150mm minimum
50mm
min
Specification:
Manufactured from 2mm thick
hot dipped pre-galvanized mild Installation Requirements:
steel to BS EN 10346 : 2009, Fixing: use BAT 3.75 x 30mm
DX51D + Z275. long square twisted sherardised
nails.
Length: 300mm
Width each wing: 30mm Fixings should be used in all
Hole diameter: 4mm timber facing nail holes.
Qty per bag: 50
Minimum timber depth of
Characteristic load capacity Fk - 150mm.
C24 timber
Ensure the timbers project a
1 pair - 6.8kN minimum of 50mm beyond
2 pairs - 16.8kN the Angle Plates.
15
ANGLE BRACKETS
Design Features
Manufactured from hot dipped
pre-galvanized mild steel to
BS EN 10346: 2009,
DX51D + Z275. AB303015
Installation Requirements: CSK for screws
Max M3.5 x 4
Angle Brackets may be used for timber/timber, Qty: 100
timber/steel and timber/masonry connections.
Brackets may be fixed with screws, nails,
bolts or coach screws.
Must be used in pairs to prevent
eccentric loading.
AB604060 AB1006060
3.75 x 30 square 4 x 40 annular
twisted nail (SN32) ring shank nail
12 x minimum in 15 x minimum in
holes indicated to holes indicated to
achieve loads achieve loads
Load Condition Load (C24 timber) Load Condition Load (C16 timber)
F1 Uplift 4.17 F1 Uplift 2.37
F2,3 Shear 5.69 F2,3 Shear 7.93
F4,5 Shear 3.55
AAB1403540 HD9090
4 x 40 annular 3.75 x 30 square
ring shank nail twisted nail (SN32)
13 x minimum in 16 x minimum in
holes indicated to holes indicated to
achieve loads achieve loads
Load Condition Load (C16 timber) Load Condition Load (C24 timber)
F1 Uplift 0.91 F1 Uplift 2.79
F2,3 Shear 3.27 F2,3 Shear 4.6
F4,5 Shear 2.1
HD15090 HD150150
3.75 x 30 square 3.75 x 30 square
twisted nail (SN32) twisted nail (SN32)
21 x minimum in 20 x minimum in
holes indicated to holes indicated to
achieve loads achieve loads
Load Condition Load (C24 timber) Load Condition Load (C24 timber)
F1 Uplift 1.7 F1 Uplift 1.67
F2,3 Shear 6.07 F2,3 Shear 6.07
18
TIMBER CONNECTORS
Split Ring
SRTC64 (A3) x 100 per box
SRTC102 (A3) x 100 per box
Designed for use with M12
and M20 bolts respectively.
Double bevelled.
Manufactured from galvanized
hot rolled steel to BSEN10025. Split Ring
Application Tools for use with timber connectors. Available to special order.
Reference Type Size
SRGT/64 Split Ring Grooving & Dapping Tool 64mm split ring
SRGT/102 Split Ring Grooving & Dapping Tool 102mm split ring
DT/67 Shear Plate Grooving & Dapping Tool 67mm shear plate
DT/102 Shear Plate Grooving & Dapping Tool 102mm plates
19
SPLICE PLATES
FRAME CRAMP
Design Features
Manufactured from 0.9mm thick
hot dipped galvanized mild steel
to BS EN 10346 : 2009 DX51D
+ Z275.
Box quantity 100
Installation Requirements
Fixing: use BAT
3.75 x 30mm long square
twisted sheradised nails.
20
BAT-U-NAIL PLATE
Design Features
Manufactured from 0.9mm
pre-galvanized mild steel to
BS EN 10346: 2009 : DX51D
+Z275.
Widths: 76, 114 and 152mm
Lengths: 51, 100, 152, 203, 254,
305 and 354mm.
Various quantities per box.
Ref. eg. BP7651.
Installation Requirements
BAT-U-Nail plates are to be fixed on both sides of the timber.
Fixing: use BAT 3.75 x 30mm long square twisted sherardised nails.
Loading in the direction of the plate stiffening ribs.
345 N/nail (parallel to timber grain).
145 N/nail (perpendicular to timber grain).
Plate compression value 40 N/mm width of plate. To calculate capacity
of connections, the lesser of anchorage, plate compression and tension
should be taken.
Fix in accordance with BS 5268 : Part 2.
21
MULTI-PURPOSE FIXING BANDS
Design Features
Manufactured from hot dipped
galvanized mild steel to
BS EN 10346 : 2009 DX51D
+ Z275.
Installation Requirements
Fixing: use BAT 3.75 x 30mm
long square twisted sherardised
nails, screws or bolts. Not to be
used below ground.
JUNCTION CLIP
Design Features
Manufactured from 0.9mm
hot dipped galvanized
mild steel to
BS EN 10346 : 2009 : DX51D +
Z275. Ref: JC1 250 per box.
Installation Requirements
Fixing: use BAT 3.75 x 30mm
long square twisted sherardised
nails or ordinary plasterboard
nails.
22
SOLE PLATE ANGLES
Design Features
Manufactured from 0.9mm thick
hot dipped galvanized mild steel
to BS EN 10346 : 2009
DX51D + Z275. Installation Requirements
BAT Sole Plate Angles may
Box quantity 100 be fixed on the inside of the
sole plate or alternatively fixed
under the sole plate with the
Ref. Width Length Upstand
upstand on the outside of the
SPA112 76mm 112mm 40mm sole plate.
SPA162 76mm 162mm 40mm
Fixing: use 3.75 x 50mm min.
length nails/masonry nails.
SAFE PLATE
SAF1 90 x 54mm
Design Features
Manufactured from 0.9mm
hot dipped galvanized mild steel
to BS EN 10346 : 2009 : DX51D
+ Z275.
200 per box
Installation Requirements
Use wherever services occur
within 75mm of face of
plasterboard or 100mm of
surface of floor deck.
Fixing: Tap in with hammer.
23
STAINLESS STEEL WALL TIES
PT Housing Wall Tie
Part E/party walls/type A
Cavities 50-100 and 125-150mm
24
STAINLESS STEEL SCREW-IN STARTER
AND CAVITY TIES
25
FRAME CRAMPS
A comprehensive range of
stainless steel frame cramps
with safety end or plain end
options for fixing to concrete,
steel and masonry.
V-drip and vertical twists are
offered as options and drips
can be offset to accommodate
insulation materials.
Compliant with BS EN 845-1
SEPE SESE SESE (V) PEFC (H) SEFC (H) SEFC (HV)
PEFC (S) SEFC (S) SEFC (SV) Debonding and isolation sleeves
Ref. Material Thickness Coil Size Widith Wall Width (mm) Quantity
(mm) (mm)
76820 0.3 65 100 5
76920 0.3 115 140 5
77020 0.3 175 225 1
77120 0.3 225 265 1
28
FLAT WIRE REINFORCEMENT
SBSF4060 3 4 60 100 20
SBSF40100 3 4 100 140/150 20
SBSF40150 3 4 150 190/200 20
SBSF40175 3 4 175 215 20
29
WALL STARTERS, UNISTARTERS
& MULTI-STARTERS
Wall Starters
Individual flanged products
designed for specific widths of
new walls.
UniStarters
The universal wallstarter for any
UniStarters
wall.
The flat flange-free design means
they can be used to construct any
wall between 75mm and 250mm
thick.
Multi-Starters
Featuring a turn-n-slide tie to
accommodate all sizes of brick
or block.
The Multi-Starter is suitable for all
wall widths from 60mm-250mm.
Multi-Starters
30
ACCESSORIES
Gallows Bracket
The Gallows Bracket provides
a method of supporting
otherwise unsupported
brickwork.
Manufactured from 50 x 50 x 5
angle, red oxide finish.
Two sizes are available (supplied
in pairs).
To suit M12 Masonry Anchors -
not supplied.
MH375375
375mm high x 375mm deep
(projection from wall)
MH490375
490mm high x 375mm deep
(projection from wall)
Stainless Steel
Annular Ring Nails
SSRN 3.35 x 50mm
1000 per box
Sherardised Nails
SN32 BAT 3.75 x 30mm
twisted 1000 per box
31
Expamet is one of the leading brands of specialist building products
in the UK, Europe and the Middle East. Operating across two
continents, we offer internationally recognisable products that are
synonymous with quality, safety and innovation. Wherever you are and
whatever your project, Expamet solutions are never far away.
info@birtleygroup.co.uk
0191 410 6631
www.birtleygroup.co.uk
Subsidiary of Hill & Smith Holdings plc
01/15