You are on page 1of 1

Vertically Polarized, Panel 65 / 18 dBi

BSA-185065/10 __
Mechanical specifications When ordering replace ___ with connector type.

Length 1530 mm 60.2 in


Width 160 mm 6.3 in Radiation pattern1)
Depth 50 mm 2.0 in
Depth with t-bracket 78 mm 3.1 in -100 -90 -80
-110 -70
4) -120 -60
Weight 4.1 kg 9.1 lbs -130 -50
-140 -40
Wind Area
-150 -30
Fore/Aft 0.23 m2 2.47 ft2 -160 -20

Side 0.08 m2 0.82 ft2 -170 -10

180 35 30 25 20 15 10 5 0
Rated Wind Velocity (Safety factor 2.0)
170 10
>277 km/hr >172 mph
160 20

Wind Load @ 100 mph (161 km/hr) 150 30

Fore/Aft 364 N 81.9 lbs 140 40


130 50
Side 145 N 32.6 lbs 120 60
110 70
100 90 80
Antenna consisting of aluminum alloy with brass
feedlines covered by a UV safe fiberglass radome. Horizontal

Mounting and Downtilting -110


-100 -90 -80
-70
Mounting brackets attach to a pipe diameter of -120 -60
-130 -50
50-102 mm (2.0-4.0 in). -140 -40
-150 -30
Mounting bracket kit #26799997
-160 -20
Downtilt bracket kit #26799999
-170 -10

35 30 25 20 15 10 5
The downtilt bracket kit includes the mounting 180 0

bracket kit. 170 10 Amphenol Antels


Exclusive 3T (True
Electrical specifications 160 20
Transmission Line
150 30
Frequency Range 1850-1990 MHz 140 40 Technology)
Impedance 50
130 50 Antenna Design:
120 60
110 70
3) Connector(s) NE or E-DIN 100 90 80
z Watercut brass feedline assembly for
1 port / bottom Vertical consistent performance.
or center
1) z Unique feedline design eliminates the need
VSWR 1.4:1
for conventional solder joints in the signal
Polarization Vertical path.
1)
Gain 18 dBi z A non-collinear system with access to
2) every radiating element for broad band-
Power Rating 250 W Radiation patterns for all antennas are
width and superior performance.
1) measured with the antenna mounted on
Half Power Angle
a fiberglass pole. z Air as insulation for virtually no internal
H-Plane 65 signal loss.
Mounting on a metal pole will typically
E-Plane 6
improve the Front-to-Back ratio.
1)
Electrical Downtilt 0 This Amphenol Antel antenna is under a five-
1) year limited warranty for repair or replacement.
Null Fill 10%
Lightning Protection Direct Ground Antenna can be ordered with bottom-fed or
center-fed connector.

Bottom-fed: BSA-185065/10 + (NE or E-DIN)


Center-fed: BSA-185065/10CF + (NE or E-DIN)
1) Typical values.
2) Power rating limited by connector only.
3) NE indicates an elongated N connector.
E-DIN indicates an elongated DIN connector.

1850-1990 MHz
4) The antenna weight listed above does not include
the bracket weight.
Improvements to mechanical and/or electrical performance
of the antenna may be made without notice.

Amphenol Antel, Inc. 1300 Capital Drive Rockford, Illinois 61109 USA Tel. (815) 399-0001 Revision Date: 7/10/07
Toll-Free (888) 417-9562 Fax. (815) 399-0156 antel@antelinc.com www.antelinc.com

You might also like