You are on page 1of 49

8.

Level 3 Repair

8-1. Block Diagram

8-1

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-2. PCB Diagrams


8-2-1. Top

8-2

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-2-1. Bottom

8-3

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3. Flow Chart of Troubleshooting

Equipments

Oscilloscope Digital Multimeter

Power Supply + driver, Tweezer

8-4

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-1. Power On

' Power On ' does not work

Yes

check the current consumption

Yes

check current consumption No


Download again
>=100mA

Yes

No
Check the Battery Voltage Change the Battery
is more than 3.3V (Because of batt. power low)

Yes

Check U503 (PMIC) and Check the problem point (short, open, crack
Power on voltage No
(C518 >1.2V, C519 >1.1V, etc)
C520>1.8V, C522,> 1.2V C529
> 1.8V) and If PMIC has problem, change U503

Yes

Check the Clock at No Check the clock generation circuit


OSC501 that
Frequency is 32K (related to OSC501)

Yes
check the initial operation

Yes

END

8-5

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-6

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-2. Initial

Initial Failure

Yes

The pin #1,2 of U206 = No


swing properly 1.8V and 0V? check U206 and UCP400 and related parts (short,
The pin #11,12 of U206= crack, etc)
swing properly 2.8V and 0V?

Yes

AP_PS_HOLD(TP501) and No
AP_N_RST_IN (R507) = Check U503 (crack, open, etc)
"low High"? (if U503 has some problem, it is to be replaced)

Yes

No
There is 32.768KHz wave forms Replace OSC 200 and OSC501
at OSC200 and OSC501

Yes

No
Check UCP200 and related parts (short, crack,
R233 >= 1.8V? etc)

Yes

There are 24MHz wave forms at No


OSC400 and 26MHz wave forms Replace OSC 400 and OSC100
at OSC100 (C128)

Yes

No
LCD display OK? Check the LCD part (short, crack, etc)

Yes

No
Sound is OK? Check the Audio Part (short, crack, etc)

Yes

END

8-7

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-8

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-3. Charging Part

Abnormal charging part

Yes

Check IFC300 pin #1 whether No Check the TA


voltage reading is greater than
4.9V (TA may not be connected properly)

Yes

Check U503 DCIN whether 5V No


is measured Resolder or Replace U301
(C502)

Yes

No
Battery is charging? Resolder or Replace U503

Yes

END

8-9

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-10

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-4. Sim Part

NO SIM

Yes

Check the connection of Reconnect the Sub PCB


the HEA301
No

Yes

Check the Sub PCB

Yes

END

VCC_2.8V_PDA VTF_2.8V CP_VSIM_1.8V

HEA301
R330
1 1 2 2
3 3 4 4
T_FLASH_D(0) T_FLASH_D(1)
5 5 6 6
T_FLASH_D(2) T_FLASH_D(3)
7 7 8 8
T_FLASH_CMD T_FLASH_CLK
9 9 10 10
T_FLASH_DETECT SIM_RST
11 11 12 12
SIM_CLK
SPK_OUT_R_P 13 13 14 14 SIM_IO
SPK_OUT_R_N 15 15 16 16 AP_JTAG_EXTRST
NC
NC
NC
NC
17
18
19
20

C329 C330
V308 V309 V306 V307 V310 V312 V311
V316
C3 3 9

L502
C5 1 9

C532 U503
C5 3 7

C533
R326
C536
R327
C5 1 8

C538

L501
C336
C5 3 4
C5 3 5

C517 C539
C5 0 4

TP5 0 1

C337
C3 3 3

C3 3 2

C338
C501
R4 3 7

R4 3 5

R4 3 8

R4 3 4

R4 3 3
U3 0 7

C340 C503
OSC501
C5 2 3

C5 2 2

R4 2 4

R4 2 2

R4 2 5

R4 2 9

R501
C508
R4 2 8

R328

R329
C4 1 4

C553
C5 5 4

C5 0 9

C5 0 6

C5 1 0

R340
C3 2 9

R331
C4 1 3
C2 8 4
HEA3 0 1
R6 0 4

C3 3 0
L6 0 1

C541
C6 0 1

V311
V3 1 6

R3 3 0

V308
U505
V312
V307 R468
U6 0 1

V310
V306 R467
R6 0 1

C2 0 8

V309 C542

R603

SC610

8-11

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-5. Microphone Part

Check main microphone function


in voice call receiver mode

Yes

Check the voltage at C267 = No


2.8V Resolder or replace U210

Yes

Check component soldering No


statuses of C281, C282 Resolder or replace C281, C282

Yes

Resolder or change the Sub-


Touch Module

Yes

END

8-12

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-13

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-6. Speaker Part

Check speaker function.


Play MP3 with maximum volume level.
Yes

No
Check signals on L209,
L210 Resolder or replace U207

Yes

Yes Check signals on


L209, L210 again

No

Resolder or replace UCP400

Check the connection of No


HEA301 Reconnect HEA301

Yes

Replace the speaker


module

Yes

END

8-14

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-15

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-7. Receiver Part

Check receiver function in voice call receiver


mode

Yes

Check the signals at ZD307, No


ZD308 Resolder or replace U207

Yes

Check the signals at ZD307, No


Resolder or replace UCP200
ZD308 again

Yes

Check the connection of No


Reconnect HDC302
HDC302

Yes

Replace the Receiver-Earjack


Ass'y

Yes

END

8-16

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-17

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-8. BT/WIFI

BT/WiFi is not working

Check BT or WiFi function No


Enable BT or WiFi Function
ON

Yes

Check the Voltage on C162 = No


Check AP PMIC(U503)
2.8V

Yes

Check 38.4MHz Clock at No


Check OSC 102
C177

Yes

Check the Voltage on L113 = No


Resolder or change L113
1.2V

Yes

Check the Status of C138, No


Resolder or Replace C138, L124, ANT106
L124, ANT106

Yes

Resolder or Replace U105

Yes

END

8-18

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-19

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-9. FM RADIO

FM Radio does not work

Yes

Check the connection of No


HDC302 Connect Earjack Ass'y correctly to HDC302

Yes

Check the Audio Signal at No Check Earphone


L302, L303

Yes

Check the Audio signal at No


C250, C251 Check Audio Codec IC (U207)

Yes

CChange U104

Yes

END

8-20

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-21

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-10. LCD

LCD is still off after PWR ON

Yes

No
Check the connection of Reconnect the HDC300
HDC300

Yes

Check the soldering status of No


Resolder EMI Filters
EMI Filters F300~F305

Yes

Check VCC_3.0V_LCD =
3.0V (C537), VLCD_1.8V = No
Check PMIC(U503)
1.8V (C307), V_BAT > 3.4V
(C308)

Yes

Replace LCD Module

Yes

END

8-22

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-23

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-11. TSP

Touch Screen does not work

Yes

No
Check LCD Connector on Reconnect the HDC300
Main PBA

Yes

No
Check the TSP Connector on Reconnect TSP Connector
LCD Module

Yes

U300 Pin 6 = 2.8V (C305, No


C310) and Pin 8 = 3.3V Resolder or Replace U300
(C306, C344)

Yes

Replace LCD Module

Yes

END

8-24

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-25

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-12. 5M CAM

"Camera" function does not work

Yes

No
Check the Camera Reconnect the HDC301
connector on Main PBA

Yes

Check the voltage


C531,C533,C535 = 2.8V, No
C534, C536 = 1.8V, Resolder U503, U303 or change PBA
C532, C521 = 1.2V
C352 = 2.8V

Yes

No
Check F308 Pin 1 is 24MHz Check UCP400 related to 24MHz

Yes

Replace the camera module

END

8-26

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

D E TB A T

B A TT
B A TT
VIC H G
V C O IN

D C IN
D C IN
B A T TMON
VL

A1
BUCK1 IN1
A2
IN1
E1
BUCK2 IN2
E2
IN2
H1
BUCK3 IN3
H2
IN3
K2
BUCK4 IN4
K8
LDO4,5,7 IN5
K9
VALIVE_1.2V_C110
IN5
C9
LDO11,12,13 IN6
D9 VUSB_1.1V_C110
IN6
A7
LDO14,15,16 IN7
B7
VADC_3.3V_C110 VCC_2.8V_PDA
IN7
G9
LDO6,8,9 IN8
H9 VTF_2.8V VUSB_3.3V_C110
IN8
B9
LDO2,3,10,17 IN9
CAM_SENSOR_CORE_1.2V
B8 0.8V~1.3V UP TO 10mA CAM_ISP_HOST_2.8V
LDO2
C8 0.8V~1.3V UP TO 50mA
VLCD_1.8V VDAC_3.3V_C110
LDO3
K10 1.6V~3.6V UP TO 300mA
CAM_ISP_SYS_2.8V
U503 LDO4

LDO5
J10 1.6V~3.6V UP TO 300mA VPLL_1.2V_C110
H10 1.6V~3.6V UP TO 150mA
LDO6
K7 1.6V~3.6V UP TO 150mA CAM_ISP_RAM_1.8V
LDO7
G10 3.0V~3.6V UP TO 150mA
CAM_AF_2.8V VCC_3.0V_LCD VCC_1.8V_PDA
LDO8
F10
LDO9
C7
LDO10
E10 CAM_SENSOR_IO_1.8V VARM_1.2V_C110
LDO11
D10
LDO12
C10
LDO13
A6
VINT_1.1V_C110
LDO14
A8
LDO15
A10
LDO16
B10
LDO17

B1
LX1
B2
LX1
C1
CAM_ISP_CORE_1.2V
LX1
F1 L502
LX2
F2
LX2
F3
LX2
J1 L503
LX3
J2
LX3
J3 L504
LX4
K3
LX4

A4
XIN
A3
XOUT
PG N D 4
PG N D 4
PG N D 3
PG N D 2
PG N D 2
P GND1
PG N D 1
A G N D2
A G N D1
NC
NC

C522 C524 C525 C526 C527 C528 C529 C532 C533 C534 C535 C536 C537 C518 C519 C520 C521
K4

K1
G2
G1
D2
D1
B5
A5
J4
2
1

V_BAT CAM_SENSOR_A2.8V
F308
L309

U303 1 IN1 5
CAM_MCLK_F OUT1 CAM_MCLK

2 IN2 6
CAM_HSYNC_F OUT2 CAM_HSYNC
4 VDD VOUT 1
3 IN3 7
CAM_VSYNC_F OUT3 CAM_VSYNC

4 IN4 8
2 CAM_PCLK OUT4 CAM_PCLK_F
3 CE C315
CAM_IO_EN GND GND GND
GND

10 9
5

C351 C352

8-27

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-13. GSM850 RX

NORMAL CONDITION
catch the channel?

NO

YES CHECK soldered


Check C115 -65dBm ?
RFS100, L103,C115,L118

NO

NO resolder or change
Check the Voltage at
PAM101, C186
C186 =V_BAT

YES

Check C126, L107,C125 NO resolder or change


-65dBm ? C126, L107,C125

YES

Check component NO resolder or change


soldering status OK at
F100
F100

YES

Check F100 PIN 8,9 NO


resolder or change
-65dBm F100

YES

Check the voltage at


{R100 = V_BAT ?}
& {C110, C264 = 2.85V ?} NO
resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100

YES NO
GSM850 Receiver is O.K? resolder or change
UCP200

END

8-28

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-29

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-14. GSM1800 RX

NORMAL CONDITION
catch the channel?

NO

YES CHECK soldered


Check C115 -65dBm ?
RFS100, L103,C115,L118

NO

Check the Voltage at NO resolder or change


C186 = V_BAT? PAM101, C186

YES

Check C140, L108 NO resolder or change


-65dBm ? C140, L108

YES

Check component NO resolder or change


soldering status OK at
F100
F100

YES

Check F100 PIN 14, 15 NO


resolder or change
-65dBm F100

YES

Check the voltage at


{R100 = V_BAT ?}
& {C110, C264 = 2.85V ?} NO
resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}
YES

YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100

YES NO
GSM850 Receiver is O.K? resolder or change
UCP200

END

8-30

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-31

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-15. WCDMA Band1 RX

CONTINUOUS RX ON
NORMAL CONDITION RF INPUT : 10700CH
catch the channel?
AMP : -50dBm

NO

YES CHECK soldered


Check C115 -65dBm ?
RFS100, L103, C115, L118

NO

Check the Voltage at NO resolder or change


C186 = V_BAT ? C186, PAM101

YES

PAM101 CHECK NO resolder or change


pin7 or C141, L109
PAM101, C141, L109
-65dBm ?

YES

Check component soldering NO resolder or change


status OK at PAM104, C185, PAM104, C185,
L120, L102, C114 ? L120, L102, C114

YES

Check component soldering


status OK at NO resolder or change
U100, F100 ? U100, F100
F100 PIN 10, 11 -65dBm

YES

Check the voltage at


{R100 = V_BAT ?} NO
& {C110, C264 = 2.85V ?} resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

NO change or resolder
Check the freq. at OSC100
:26MHz ? OSC100

YES

NO resolder or change
WCDMA BAND1 Receiver is O.K? UCSP200

YES
END

8-32

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-33

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-16. WCDMA Band2 / GSM1900 RX

CONTINUOUS RX ON
RF INPUT : 9800CH
NORMAL CONDITION
catch the channel? AMP : -50dBm

NO

YES CHECK soldered


Check C115 -65dBm ?
RFS100, L103, C115, L118

NO

Check the Voltage at NO resolder or change


C186 = V_BAT ? C186, PAM101

YES

PAM101 CHECK NO resolder or change


pin9 or C127, C143, L111
PAM101, C127, C143, L111
-65dBm ?

YES

Check component soldering NO resolder or change


status OK at PAM103, C113, PAM103, C113, L101, C101,
L101, C101 ? C131
Check C131-65dBm ?

YES

Check component soldering


status OK at NO resolder or change
U100, F100 ? U100, F100
F100 PIN 12, 13 -65dBm

YES

Check the voltage at


{R100 = V_BAT ?} NO
& {C110, C264 = 2.85V ?} resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

NO change or resolder
Check the freq. at OSC100
:26MHz ? OSC100

YES

NO resolder or change
WCDMA BAND2, PCS1900 Receiver is O.K? UCSP200

YES
END

8-34

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-35

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-17. WCDMA Band8 / GSM900 RX

CONTINUOUS RX ON
RF INPUT : 9800CH
NORMAL CONDITION
catch the channel? AMP : -50dBm

NO

YES CHECK soldered


Check C115 -65dBm ?
RFS100, L103, C115, L118

NO

Check the Voltage at NO resolder or change


C186 = V_BAT ? C186, PAM101

YES

PAM101 CHECK NO resolder or change


pin5 or C142, L110
PAM101, C142, L110
-65dBm ?

YES

Check component soldering NO resolder or change


status OK at PAM102, C122, PAM102, C122, L106, L105,
L106, L105, C121 ? C121, C116
Check C116-65dBm ?

YES

Check component soldering


status OK at NO resolder or change
U100, F100 ? U100, F100
F100 PIN 6, 7 -65dBm

YES

Check the voltage at


{R100 = V_BAT ?} NO
& {C110, C264 = 2.85V ?} resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

NO change or resolder
Check the freq. at OSC100
:26MHz ? OSC100

YES

NO resolder or change
WCDMA BAND8, GSM900 Receiver is O.K? UCSP200

YES
END

8-36

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-37

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-18. GSM850/GSM900 TX CONTINOUS TX ON CONDITION


TX POWER DAC:14500 CODE
APPLIED
GSM850 CH : 190
GSM900 CH : 62
RBW : 100KHz
VBW : 100KHz
SPAN : 10MHz
REF LEV. : 10dBm
ATT. : 20dB

NO CHECK soldered
PAM101 PIN1 : About RFS100, L103,C115,L118,
30dBm ? C183, ANT102

YES

Check the Voltage at


C186,C187,C139 = NO resolder or change
V_BAT? PAM101, C186, C187, C189

YES

Check C132 about 2 V NO resolder or change


ok? U101

YES

Check PAM101 pin 25 NO resolder or change


about 4dBm U101

YES

Check the voltage at


{R100 = V_BAT ?}
& {C110, C264 = 2.85V ?} NO
resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100

YES NO
GSM850/900 Transmitter is O.K? resolder or change
UCP200

END

8-38

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-19. DCS/PCS TX CONTINOUS TX ON CONDITION


TX POWER DAC:14500 CODE
APPLIED
GSM850 CH : 190
GSM900 CH : 62
RBW : 100KHz
VBW : 100KHz
SPAN : 10MHz
REF LEV. : 10dBm
ATT. : 20dB

NO CHECK soldered
PAM101 PIN1 : About RFS100, L103,C115,L118,
27dBm ? C183, ANT102

YES

Check the Voltage at


C186,C134,C139 = NO resolder or change
V_BAT? PAM101, C186, C134, C139

YES

Check C132 about 1.8 V NO resolder or change


ok? U101

YES

Check PAM101 pin 25 NO resolder or change


about 4dBm U101

YES

Check the voltage at


{R100 = V_BAT ?}
& {C110, C264 = 2.85V ?} NO
resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100

YES NO
DCS/PCS Transmitter is O.K? resolder or change
UCP200

END

8-39

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-40

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-20. WCDMA BAND1 TX CONTINOUS TX ON CONDITION


TX POWER DAC:14500 CODE
APPLIED
GSM850 CH : 190
GSM900 CH : 62
NO CHECK soldered RBW : 100KHz
Check PAM101 PIN1 : RFS100, L103,C115,L118, VBW : 100KHz
About 22 dBm ? C183, ANT102 SPAN : 10MHz
REF LEV. : 10dBm
ATT. : 20dB
YES

Check the Voltage at


NO resolder or change
C186 = V_BAT?
PAM101, C186

YES

Check C141, L109 : NO resolder or change


About 22dBm ? C141, L109

YES

NO
Check C135 resolder or change
about 3.4 V ? U102

YES

Check PAM104 pin 7 NO resolder or change


about 22dBm ? PAM104

YES

NO resolder or change
Check C147
about 8dBm ? U101

YES

Check the voltage at


{R100 = V_BAT ?}
& {C110, C264 = 2.85V ?} NO
resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100

YES NO
WCDMA 2100 Transmitter is O.K? resolder or change
UCP200

END

8-41

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-42

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-21. WCDMA BAND2 TX CONTINOUS TX ON CONDITION


TX POWER DAC:14500 CODE
APPLIED
GSM850 CH : 190
GSM900 CH : 62
NO CHECK soldered RBW : 100KHz
Check PAM101 PIN1 : RFS100, L103,C115,L118, VBW : 100KHz
About 22 dBm ? C183, ANT102 SPAN : 10MHz
REF LEV. : 10dBm
ATT. : 20dB
YES

Check the Voltage at


NO resolder or change
C186 = V_BAT?
PAM101, C186

YES

Check C143, L111 : NO resolder or change


About 22dBm ? C143, L111

YES

NO
Check C135 resolder or change
about 3.4 V ? U102

YES

Check PAM103 pin 7 NO resolder or change


about 22dBm ? PAM103

YES

NO resolder or change
Check C146
about 8dBm ? U101

YES

Check the voltage at


{R100 = V_BAT ?}
& {C110, C264 = 2.85V ?} NO
resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100

YES NO
WCDMA 1900 Transmitter is O.K? resolder or change
UCP200

END

8-43

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-44

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-3-22. WCDMA BAND8 TX CONTINOUS TX ON CONDITION


TX POWER DAC:14500 CODE
APPLIED
GSM850 CH : 190
GSM900 CH : 62
NO CHECK soldered RBW : 100KHz
Check PAM101 PIN1 : RFS100, L103,C115,L118, VBW : 100KHz
About 22 dBm ? C183, ANT102 SPAN : 10MHz
REF LEV. : 10dBm
ATT. : 20dB
YES

Check the Voltage at


NO resolder or change
C186 = V_BAT?
PAM101, C186

YES

Check C142, L110 : NO resolder or change


About 22dBm ? C142, L110

YES

NO
Check C135 resolder or change
about 3.4 V ? U102

YES

Check PAM102 pin 7 NO resolder or change


about 22dBm ? PAM102

YES

NO resolder or change
Check C145
about 8dBm ? U101

YES

Check the voltage at


{R100 = V_BAT ?}
& {C110, C264 = 2.85V ?} NO
resolder or change
& {C111,C112,C233 = 1.8V?} UCP200
& {C109,C263 = 2.85V ?}
& {C112 = 1.8GV ?}

YES

YES NO
Check the freq. at C128 change or resolder
: 26MHz ? OSC100

YES NO
DCS/PCS Transmitter is O.K? resolder or change
UCP200

END

8-45

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-46

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

8-4. Service Schematics

- NC Point(Top View)

: NC

UCP400
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

A A

B B

C C

D D

E E

F F

G G

H H

J J

K K

L L

M M

N N

P P

R R

T T

U U

V V

W W

Y Y

AA AA

AB AB

AC AC

AD AD

AE AE

AF AF

AG AG

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

8-47

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

: NC

UCP200

8-48

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization
Level 3 Repair

: NC

UME301

8-49

SAMSUNG Proprietary-Contents may change without notice


This Document can not be used without Samsung's authorization

You might also like