Professional Documents
Culture Documents
MasterFlow 932 AN
(Formerly known as Concresive 1450i)
DESCRIPTION FEATURES
MasterFlow 932 AN is a two-component 1:1 Fixings close to free edges
pure epoxy resin based chemical anchoring Fire tested
grout for use in cracked and uncracked concrete Versatile
under normal as well as seismic conditions Anchoring without expansion pressure
(seismic category C1). Designed for most High load capacities
demanding structural applications and rebar Extended gel/open time
connections, Suitable for dry and wet holes
MasterFlow 932 AN offers high load-bearing
capacity.
PACKAGING
MasterFlow 932 AN is available in side-by-side
USES & APPLICATIONS
cartridge of 400ml (12 cartridges in a box).
Structural applications in cracked and
uncracked concrete applications in seismic INSTALLATION PROCEDURE
zones (C1)
Please refer to the method statement or contact
Faades
BASF Technical Services department.
Post installed rebar connections
Crash barriers
Structural steel
PHYSICAL PROPERTIES
INSTALLATION PARAMETERS
Diameter of rebar 10 12 16 20 25 32
Drilled hole diameter 14 16 20 25 32 40
DESIGN RESISTANCE
Rebar size 10 12 16 20 25 32
Effective embedment depth hef [mm] 90 110 125 170 250 300
non-cracked concrete
temperature range (-40C / +40C)
tension C20/25 NRd,p [kN] 18.85 23.70 38.90 66.12 121.55 186.70
C50/60 NRd,p [kN] 21.49 27.01 44.34 75.38 138.57 212.84
shear C20/25 NRd,s [kN] 9.33 14.67 20.67 57.33 90.00 147.33
cracked concrete
temperature range (-40C / +40C)
tension C20/25 NRd,p [kN] 14.14 17.77 20.94 35.60 46.75 71.81
C50/60 NRd,p [kN] 15.41 19.37 22.83 38.81 50.96 78.27
shear C20/25 NRd,s [kN] 9.33 14.67 20.67 57.33 90.00 147.33
RECOMMENDED RESISTANCE
Rebar size 10 12 16 20 25 32
Effective embedment depth hef [mm] 90 110 125 170 250 300
non-cracked concrete
temperature range (-40C / +40C)
tension C20/25 NRec,p [kN] 13.46 16.93 27.78 47.23 86.82 133.36
C50/60 NRec,p [kN] 15.35 19.30 31.67 53.84 98.98 152.03
shear C20/25 NRec,s [kN] 6.67 10.48 14.76 40.95 64.29 105.24
cracked concrete
temperature range (-40C / +40C)
tension C20/25 NRec,p [kN] 10.10 12.69 14.96 25.43 33.39 51.29
C50/60 NRec,p [kN] 11.01 13.84 16.31 27.72 36.40 55.91
shear C20/25 NRec,s [kN] 6.67 10.48 14.76 40.95 64.29 105.24
fyk = 500 N/mm
Partial safety factor 1.4
For resistance values in higher temperatures, please contact BASF Technical Services.
All the above resistance values are considering combined pull out and concrete cone failure in tension and steel
failure in shear.
MasterFlow 932 AN
(Formerly known as Concresive 1450i)
NOTE
Field service, where provided, does not
constitute supervisory responsibility. For
additional information contact your local BASF
representative.
BASF_CC-UAE/Fl_932AN_05_04/v4/09_15
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.
Field service where provided does not constitute supervisory responsibility. Suggestions made by BASF either
NOTE orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they, and not
BASF, are responsible for carrying out procedures appropriate to a specific application.
Page: 1/13
BASF Safety data sheet according to Regulation (EC) No. 1907/2006 as amended from time to time.
Date / Revised: 30.06.2015 Version: 2.0
Product: MasterFlow 932AN also Concressive 1450i
(ID no. 30572095/SDS_GEN_EU/EN)
Date of print 17.07.2015
Company:
BASF SE
67056 Ludwigshafen
GERMANY
Operating Division Construction Chemicals
For the classifications not written out in full in this section the full text can be found in section 16.
Pictogram:
Signal Word:
Danger
Hazard Statement:
H314 Causes severe skin burns and eye damage.
H312 Harmful in contact with skin.
H302 Harmful if swallowed.
H317 May cause an allergic skin reaction.
H411 Toxic to aquatic life with long lasting effects.
If applicable information is provided in this section on other hazards which do not result in
classification but which may contribute to the overall hazards of the substance or mixture.
Not applicable
3.2. Mixtures
Chemical nature
4-tert-Butylphenol
Content (W/W): >= 1 % - < 15 % Skin Corr./Irrit. 2
CAS Number: 98-54-4 Eye Dam./Irrit. 1
EC-Number: 202-679-0 Repr. 2 (fertility)
REACH registration number: 01- Aquatic Chronic 1
2119489419-21 H318, H315, H361f, H410
benzyl alcohol
Content (W/W): >= 1 % - < 15 % Acute Tox. 4 (oral)
CAS Number: 100-51-6 Acute Tox. 4 (Inhalation - mist)
EC-Number: 202-859-9 Acute Tox. 4 (dermal)
REACH registration number: 01- Eye Dam./Irrit. 2
2119492630-38 H319, H312, H332, H302
INDEX-Number: 603-057-00-5
m-Phenylenebis(methylamine)
Page: 4/13
BASF Safety data sheet according to Regulation (EC) No. 1907/2006 as amended from time to time.
Date / Revised: 30.06.2015 Version: 2.0
Product: MasterFlow 932AN also Concressive 1450i
(ID no. 30572095/SDS_GEN_EU/EN)
Date of print 17.07.2015
Content (W/W): >= 1 % - < 15 % Acute Tox. 4 (oral)
CAS Number: 1477-55-0 Acute Tox. 4 (Inhalation - mist)
EC-Number: 216-032-5 Skin Corr./Irrit. 1B
Eye Dam./Irrit. 1
Skin Sens. 1B
H332, H302, H317, H314
EUH071
For the classifications not written out in full in this section, including the hazard classes and the
hazard statements, the full text is listed in section 16.
If inhaled:
If difficulties occur after vapour/aerosol has been inhaled, remove to fresh air and seek medical
attention.
On skin contact:
After contact with skin, wash immediately with plenty of water and soap. Under no circumstances
should organic solvent be used. If irritation develops, seek medical attention.
On ingestion:
Rinse mouth immediately and then drink plenty of water, seek medical attention. Do not induce
vomiting unless told to by a poison control center or doctor.
4.2. Most important symptoms and effects, both acute and delayed
Symptoms: Eye irritation, skin irritation, allergic contact dermatitis
Page: 5/13
BASF Safety data sheet according to Regulation (EC) No. 1907/2006 as amended from time to time.
Date / Revised: 30.06.2015 Version: 2.0
Product: MasterFlow 932AN also Concressive 1450i
(ID no. 30572095/SDS_GEN_EU/EN)
Date of print 17.07.2015
4.3. Indication of any immediate medical attention and special treatment needed
Treatment: Treat according to symptoms (decontamination, vital functions), no known specific
antidote.
Further information:
The degree of risk is governed by the burning substance and the fire conditions. Contaminated
extinguishing water must be disposed of in accordance with official regulations.
Hand protection:
Suitable chemical resistant safety gloves (EN 374) also with prolonged, direct contact
(Recommended: Protective index 6, corresponding > 480 minutes of permeation time according to
EN 374): E.g. nitrile rubber (0.4 mm), chloroprene rubber (0.5 mm), butyl rubber (0.7 mm) etc.
Manufacturer's directions for use should be observed because of great diversity of types.
Eye protection:
Tightly fitting safety goggles (splash goggles) (e.g. EN 166)
Body protection:
Body protection must be chosen based on level of activity and exposure.
Form: paste
Colour: beige to grey
Odour: characteristic
Odour threshold:
No applicable information available.
pH value:
Corrosive.
Flash point: > 100 C
Flammability: not flammable
Density: 1.3 g/cm3
Solubility in water: partly soluble
Self ignition: not self-igniting
Other Information:
If necessary, information on other physical and chemical parameters is indicated in this section.
Acute toxicity
Irritation
Respiratory/Skin sensitization
Assessment of sensitization:
Sensitization after skin contact possible.
Assessment of mutagenicity:
The chemical structure does not suggest a specific alert for such an effect.
Carcinogenicity
Assessment of carcinogenicity:
Based on the ingredients there is no suspicion of a carcinogenic effect in humans.
Reproductive toxicity
Developmental toxicity
Assessment of teratogenicity:
The chemical structure does not suggest a specific alert for such an effect.
Page: 9/13
BASF Safety data sheet according to Regulation (EC) No. 1907/2006 as amended from time to time.
Date / Revised: 30.06.2015 Version: 2.0
Product: MasterFlow 932AN also Concressive 1450i
(ID no. 30572095/SDS_GEN_EU/EN)
Date of print 17.07.2015
Repeated dose toxicity and Specific target organ toxicity (repeated exposure)
Based on our experience and the information available, no adverse health effects are expected if
handled as recommended with suitable precautions for designated uses. The product has not been
tested. The statements on toxicology have been derived from the properties of the individual
components.
Bioaccumulation potential:
Because of the product's consistency and low water solubility, bioavailability is improbable.
The product does not fulfill the criteria for PBT (Persistent/bioaccumulative/toxic) and vPvB (very
persistent/very bioaccumulative).
Contaminated packaging:
Contaminated packaging should be emptied as far as possible; then it can be passed on for
recycling after being thoroughly cleaned.
Land transport
ADR
UN number UN1760
UN proper shipping name: CORROSIVE LIQUID, N.O.S. (contains M-
PHENYLENEBIS(METHYLAMINE), BISPHENOL-A-
EPICHLORHYDRIN RESINS M <=700)
Transport hazard class(es): 8, EHSM
Packing group: II
Environmental hazards: yes
Special precautions for Tunnel code: E
user:
RID
UN number UN1760
UN proper shipping name: CORROSIVE LIQUID, N.O.S. (contains M-
PHENYLENEBIS(METHYLAMINE), BISPHENOL-A-
EPICHLORHYDRIN RESINS M <=700)
Transport hazard class(es): 8, EHSM
Packing group: II
Environmental hazards: yes
Special precautions for None known
user:
Page: 11/13
BASF Safety data sheet according to Regulation (EC) No. 1907/2006 as amended from time to time.
Date / Revised: 30.06.2015 Version: 2.0
Product: MasterFlow 932AN also Concressive 1450i
(ID no. 30572095/SDS_GEN_EU/EN)
Date of print 17.07.2015
Sea transport
IMDG
UN number: UN 1760
UN proper shipping name: CORROSIVE LIQUID, N.O.S. (contains M-
PHENYLENEBIS(METHYLAMINE), BISPHENOL-A-
EPICHLORHYDRIN RESINS M <=700)
Transport hazard class(es): 8, EHSM
Packing group: II
Environmental hazards: yes
Marine pollutant: YES
Special precautions for None known
user:
Air transport
IATA/ICAO
UN number: UN 1760
UN proper shipping name: CORROSIVE LIQUID, N.O.S. (contains M-
PHENYLENEBIS(METHYLAMINE), BISPHENOL-A-
EPICHLORHYDRIN RESINS M <=700)
Transport hazard class(es): 8
Packing group: II
Environmental hazards: No Mark as dangerous for the environment is needed
Special precautions for None known
user:
14.1. UN number
See corresponding entries for UN number for the respective regulations in the tables above.
Page: 12/13
BASF Safety data sheet according to Regulation (EC) No. 1907/2006 as amended from time to time.
Date / Revised: 30.06.2015 Version: 2.0
Product: MasterFlow 932AN also Concressive 1450i
(ID no. 30572095/SDS_GEN_EU/EN)
Date of print 17.07.2015
14.7. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
Regulation: Not evaluated
Shipment approved: Not evaluated
Pollution name: Not evaluated
Pollution category: Not evaluated
Ship Type: Not evaluated
If other regulatory information applies that is not already provided elsewhere in this safety data
sheet, then it is described in this subsection.
Full text of the classifications, including the hazard classes and the hazard statements, if mentioned
in section 2 or 3:
Acute Tox. Acute toxicity
Skin Corr./Irrit. Skin corrosion/irritation
Skin Sens. Skin sensitization
Page: 13/13
BASF Safety data sheet according to Regulation (EC) No. 1907/2006 as amended from time to time.
Date / Revised: 30.06.2015 Version: 2.0
Product: MasterFlow 932AN also Concressive 1450i
(ID no. 30572095/SDS_GEN_EU/EN)
Date of print 17.07.2015
Aquatic Chronic Hazardous to the aquatic environment - chronic
Eye Dam./Irrit. Serious eye damage/eye irritation
Repr. Reproductive toxicity
Skin Irrit. Skin irritation
Eye Irrit. Serious eye irritation
H318 Causes serious eye damage.
H315 Causes skin irritation.
H361f Suspected of damaging fertility.
H410 Very toxic to aquatic life with long lasting effects.
H319 Causes serious eye irritation.
H312 Harmful in contact with skin.
H332 Harmful if inhaled.
H302 Harmful if swallowed.
H317 May cause an allergic skin reaction.
H314 Causes severe skin burns and eye damage.
H411 Toxic to aquatic life with long lasting effects.
EUH071 Corrosive to the respiratory tract.
The data contained in this safety data sheet are based on our current knowledge and experience and
describe the product only with regard to safety requirements. The data do not describe the product's
properties (product specification). Neither should any agreed property nor the suitability of the product for
any specific purpose be deduced from the data contained in the safety data sheet. It is the responsibility
of the recipient of the product to ensure any proprietary rights and existing laws and legislation are
observed.
Vertical lines in the left hand margin indicate an amendment from the previous version.