Professional Documents
Culture Documents
DATA SHEET
TDA7052A/AT
1 W BTL mono audio amplifier with
DC volume control
Product specification July 1994
Supersedes data of August 1991
NXP Semiconductors Product specification
ORDERING INFORMATION
Notes
1. SOT97-1.
2. SOT96-1.
July 1994 2
NXP Semiconductors Product specification
VP
2
positive input
DC volume 4
control
I i 8
negative output
STABILIZER TEMPERATURE
Vref PROTECTION
3 6 MCD385 - 1
signal power
ground ground
Fig.1 Block diagram.
PINNING
July 1994 3
NXP Semiconductors Product specification
FUNCTIONAL DESCRIPTION Thus a reduced power supply with smaller capacitors can
be used which results in cost savings.
The TDA7052A/AT are mono BTL output amplifiers with
DC volume control, designed for use in TV and monitors For portable applications there is a trend to decrease the
but also suitable for battery fed portable recorders and supply voltage, resulting in a reduction of output power at
radios. conventional output stages. Using the BTL principle
increases the output power.
In conventional DC volume circuits the control or input
stage is AC coupled to the output stage via external The maximum gain of the amplifier is fixed at 35.5 dB. The
capacitors to keep the offset voltage low. DC volume control stage has a logarithmic control
characteristic.
In the TDA7052A/AT the DC volume control stage is
integrated into the input stage so that no coupling The total gain can be controlled from 35.5 dB to 44 dB. If
capacitors are required and yet a low offset voltage is the DC volume control voltage is below 0.3 V, the device
maintained. At the same time the minimum supply remains switches to the mute mode.
low.
The amplifier is short-circuit proof to ground, VP and
The BTL principle offers the following advantages: across the load. Also a thermal protection circuit is
Lower peak value of the supply current implemented. If the crystal temperature rises above
+150 C the gain will be reduced, so the output power is
The frequency of the ripple on the supply voltage is twice reduced.
the signal frequency.
Special attention is given to switch on and off clicks, low
HF radiation and a good overall stability.
LIMITING VALUES
In accordance with the Absolute Maximum System (IEC 134)
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
VP supply voltage range 18 V
IORM repetitive peak output current 1.25 A
IOSM non-repetitive peak output current 1.5 A
Ptot total power dissipation Tamb 25%
TDA7052A 1.25 W
TDA7052AT 0.8 W
Tamb operating ambient temperature range 40 +85 C
Tstg storage temperature range 55 +150 C
Tvj virtual junction temperature +150 C
Tsc short-circuit time 1 hr
V2 input voltage pin 2 8 V
V4 input voltage pin 4 8 V
July 1994 4
NXP Semiconductors Product specification
THERMAL RESISTANCE
July 1994 5
NXP Semiconductors Product specification
CHARACTERISTICS
VP = 6 V; Tamb = 25 C; f = 1 kHz; TDA7052A: RL = 8 ; TDA7052AT: RL = 16 ; unless otherwise specified (see Fig.6).
July 1994 6
NXP Semiconductors Product specification
MCD388 MCD389 - 1
40 1000
handbook, halfpage handbook, halfpage
gain V
noise
(dB)
(V)
20
800
0
600
20
400
40
200
60
80 0
0 0.4 0.8 1.2 1.6 2.0 0 0.4 0.8 1.2 1.6 2.0
V (V) V4 (V)
4
MCD390 - 1
100
handbook, halfpage
I4
(A)
60
20
20
60
100
0 0.4 0.8 1.2 1.6 2.0
V4 (V)
July 1994 7
NXP Semiconductors Product specification
APPLICATION INFORMATION
(1)
VP = 6 V
handbook, full pagewidth
100 nF 220 F
1
7
n.c.
TDA7052A
TDA7052AT I + i 5
positive
input 0.47 F
2
R L= 8
4 (TDA7052A)
R L = 16
(TDA7052A/AT)
I i 8
RS 5 k
STABILIZER TEMPERATURE
Vref PROTECTION
DC
volume
3 6
control
MCD386 - 1
ground
This capacitor can be omitted if the 220 F electrolytic capacitor is connected close to pin 1.
handbook, halfpage
volume
control
4
1 F 1 M
MCD387
July 1994 8
NXP Semiconductors Product specification
PACKAGE OUTLINES
DIP8: plastic dual in-line package; 8 leads (300 mil) SOT97-1
D ME
seating plane
A2 A
L A1
c
Z w M
b1
e (e 1)
MH
b b2
8 5
pin 1 index
E
1 4
0 5 10 mm
scale
UNIT
A A1 A2
b b1 b2 c D (1) E (1) e e1 L ME MH w Z (1)
max. min. max. max.
1.73 0.53 1.07 0.36 9.8 6.48 3.60 8.25 10.0
mm 4.2 0.51 3.2 2.54 7.62 0.254 1.15
1.14 0.38 0.89 0.23 9.2 6.20 3.05 7.80 8.3
inches 0.068 0.021 0.042 0.014 0.39 0.26 0.14 0.32 0.39
0.17 0.02 0.13 0.1 0.3 0.01 0.045
0.045 0.015 0.035 0.009 0.36 0.24 0.12 0.31 0.33
Note
1. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
99-12-27
SOT97-1 050G01 MO-001 SC-504-8
03-02-13
July 1994 9
NXP Semiconductors Product specification
SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1
D E A
X
y HE v M A
8 5
Q
A2
(A 3) A
A1
pin 1 index
Lp
1 4 L
e w M detail X
bp
0 2.5 5 mm
scale
0.25 1.45 0.49 0.25 5.0 4.0 6.2 1.0 0.7 0.7
mm 1.75 0.25 1.27 1.05 0.25 0.25 0.1
0.10 1.25 0.36 0.19 4.8 3.8 5.8 0.4 0.6 0.3 8o
o
0.010 0.057 0.019 0.0100 0.20 0.16 0.244 0.039 0.028 0.028 0
inches 0.069 0.01 0.05 0.041 0.01 0.01 0.004
0.004 0.049 0.014 0.0075 0.19 0.15 0.228 0.016 0.024 0.012
Notes
1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included.
2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included.
99-12-27
SOT96-1 076E03 MS-012
03-02-18
July 1994 10
NXP Semiconductors Product specification
July 1994 11
NXP Semiconductors Product specification
DOCUMENT PRODUCT
DEFINITION
STATUS(1) STATUS(2)
Objective data sheet Development This document contains data from the objective specification for product
development.
Preliminary data sheet Qualification This document contains data from the preliminary specification.
Product data sheet Production This document contains the product specification.
Notes
1. Please consult the most recently issued document before initiating or completing a design.
2. The product status of device(s) described in this document may have changed since this document was published
and may differ in case of multiple devices. The latest product status information is available on the Internet at
URL http://www.nxp.com.
July 1994 12
NXP Semiconductors Product specification
Limiting values Stress above one or more limiting Quick reference data The Quick reference data is an
values (as defined in the Absolute Maximum Ratings extract of the product data given in the Limiting values and
System of IEC 60134) will cause permanent damage to Characteristics sections of this document, and as such is
the device. Limiting values are stress ratings only and not complete, exhaustive or legally binding.
(proper) operation of the device at these or any other
Non-automotive qualified products Unless this data
conditions above those given in the Recommended
sheet expressly states that this specific NXP
operating conditions section (if present) or the
Semiconductors product is automotive qualified, the
Characteristics sections of this document is not warranted.
product is not suitable for automotive use. It is neither
Constant or repeated exposure to limiting values will
qualified nor tested in accordance with automotive testing
permanently and irreversibly affect the quality and
or application requirements. NXP Semiconductors accepts
reliability of the device.
no liability for inclusion and/or use of non-automotive
Terms and conditions of commercial sale NXP qualified products in automotive equipment or
Semiconductors products are sold subject to the general applications.
terms and conditions of commercial sale, as published at
In the event that customer uses the product for design-in
http://www.nxp.com/profile/terms, unless otherwise
and use in automotive applications to automotive
agreed in a valid written individual agreement. In case an
specifications and standards, customer (a) shall use the
individual agreement is concluded only the terms and
product without NXP Semiconductors warranty of the
conditions of the respective agreement shall apply. NXP
product for such automotive applications, use and
Semiconductors hereby expressly objects to applying the
specifications, and (b) whenever customer uses the
customers general terms and conditions with regard to the
product for automotive applications beyond NXP
purchase of NXP Semiconductors products by customer.
Semiconductors specifications such use shall be solely at
No offer to sell or license Nothing in this document customers own risk, and (c) customer fully indemnifies
may be interpreted or construed as an offer to sell products NXP Semiconductors for any liability, damages or failed
that is open for acceptance or the grant, conveyance or product claims resulting from customer design and use of
implication of any license under any copyrights, patents or the product for automotive applications beyond NXP
other industrial or intellectual property rights. Semiconductors standard warranty and NXP
Semiconductors product specifications.
Export control This document as well as the item(s)
described herein may be subject to export control
regulations. Export might require a prior authorization from
national authorities.
July 1994 13
NXP Semiconductors
provides High Performance Mixed Signal and Standard Product
solutions that leverage its leading RF, Analog, Power Management,
Interface, Security and Digital Processing expertise
Customer notification
This data sheet was changed to reflect the new company name NXP Semiconductors, including new legal
definitions and disclaimers. No changes were made to the technical content, except for package outline
drawings which were updated to the latest version.
Contact information
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands RM5/02/pp14 Date of release: July 1994