Professional Documents
Culture Documents
Vol.03,Issue.30
October-2014,
Pages:5929-5932
www.ijsetr.com
Advanced Mobile Signal Jammer for GSM, CDMA and 3G Networks with
Prescheduled Time Duration using ARM7 TDMI Processor Based
LPC2148 Controller
KAKU RAMAKRISHNA1, TULASI SANATH KUMAR2
1
PG Scholar, Dept of ECE, ASCET, Gudur, Andhrapradesh, India.
2
Assistant Professor, Dept of ECE, ASCET, Gudur, Andhrapradesh, India.
Abstract: This Paper is designed and implemented for mobile phone signal jammers for GSM, CDMA and 3G networks with
prescheduled time duration using ARM7.the mobile jammers block mobile phone use by sending out radio waves along the same
frequencies that mobile phone use .this case enough interference with the communication between mobile phone and
communicating towers to render the phones unusable .upon activating mobile jammers all mobile phones will indicate NO
NETWORK AVAILABLE . Incoming calls are blocked as if the mobile phone were off. When the mobile jammers are turned
off, all mobile phones will automatically re-establish communications and provide full service .the activation and deactivation
time schedules can be programmed with microcontroller. Real time clock chip DS1307 is used to set the schedule. In this project
we have a jammer section, microcontroller. RTC and GSM modem .this information is given to the microcontroller will send
data to GSM just before the select time and GSM will send message to the users whose number are programmed in the GSM
that the jammer is going to active and communication will be stopped. After message sent by GSM. Mobile jammer circuit will
active and signal are jammed or blocked.
Spoofing: In this kind of jamming, the device forces the RF amplification (gain stage): boost the power of the radio
mobile to turn off itself. This type is very difficult to be frequency output to high enough level to jam a signal
implemented since the jamming device first detects any
Check your phone: if the battery on your phone is okay and
mobile phone in a specific area, then the device sends the
youd like to continue your conversation, try walking away
signal to disable the mobile phone .some type of this
from the the area. You may be able to get out of the jammers
technique can detect if a nearby mobile phone is there and
range with just a few steps.
sends a message to tell the user to switch the phone to the
silent mode (intelligent beacon disablers). 3. Antenna
Every jamming device has an antenna to send the signal.
Shielding attacks: This is known as TEMPEST or EMF Some are contained rical cabinet. On stronger device,
shielding. This kind required closing an area in a faraday antennas are external to provide longer range and tuned for
cage so that any device inside this cage cannot transmit or individual frequencies. The effect of jamming depends on the
receiver RF signal from outside of the cage. This area can be jamming-to- signal ratio (j/s), modulation schema, channel
large as buildings. coding and interleaving of the target system. Generally
jamming-to- signal ratio can measure according to the
Denial of service: This technique is referred to DOS. In this following equation
technique, the device transmits a noise signal at the same
operating frequency of the mobile phone in order to decrease
the signal -to-noise ratio (SNR) of the mobile under its (1)
minimum value. This kind of jamming technique is the
simplest one since the device is always on. Our device is of Pj=jammer power, Pt-transmitter power, Gjr=antenna gain
this type. from jammer to receiver, Grj=antenna gain from receiver to
jammer , Gtr=antenna gain from transmitter to receiver ,
Grt=antenna gain from receiver to transmitter,
Br=communication receiver bandwidth, Bj=jamming
transmitter bandwidth, Rtr=rang between communication
transmitter and receiver, Rjt=range between jammer and
communication receiver, Lr=jammer signal loss,
Lr=communication signal loss
B. Micro controller
This section forms the control unit of the whole project.
This section basically consists of a microcontroller with its
associated circuitry like crystal with capacitors, reset circuit, In our design, the jamming frequency must be the same
pull up resistors (if needed) and so on. The microcontroller the downlink, because it needs lower power to do jamming
forms the heart of the project because it controls the drives then the uplink rang and there is no need to jam the base
begins interfaced and communicates with the drives station itself. So, our frequency design will be as follows:
according to the program being written. a microcontroller is a
small computer on a single integrated circuit consisting of a GSM 900---- -- 935-960 MHz
relatively simple CPU combined with support function such
as crystal oscillator ,timers, watchdog timer, serial and analog GSM 1800 1805-1880 MHz
i/o etc. microcontroller are also used in specific, high
technology, and aerospace projects. Microcontrollers are The CDMA frequency range will be 860-894 MHz (Asia
designed for small or dedicated application. & Europe) and 850-894 MHz (United States).
A. Legal Issues
India: government and schools use jammers. United
States: illegal to operate, manufacture, import, or offer of up
to $11,000 and imprisonment of up to one year. Pakistan: