Professional Documents
Culture Documents
Product Description Interpon D2525 ECO Metallic is a series of super durable powder coatings specifically formulated
without TGIC, for use on architectural aluminum components. Interpon D2525 ECO Metallic surpasses
the performance of all leading architectural powders. It offers significantly higher gloss retention and
resistance to colour change combined with maximum film integrity to ensure long term cosmetic and
functional protection. Interpon D2525 ECO Metallic coating ranges are designed to deflect the infrared
spectrum of sunlight, thus reducing surface temperatures and lowering energy consumption. Increase in
reflective properties is summarized in Solar Reflective Properties section. Interpon D2525 ECO
Metallic powders are available in 20 shades in Matt and metallic effect.
The Interpon D2525 ECO Metallic range has Qualicoat Class 2 and GSB Master approvals for super
durable architectural powder coatings and conforms to the requirements of EN12206 (high durability
systems).
The Interpon Interpon D2525 ECO Metallic finishes can be produced with Dry Blended & Bonding
technologies.
Product codes_Dry blend technologies: YW296X (Ral 9006)YW297X (Ral 9007)YW278X (Ral 7048)
Product codes_Bonding technologies: YW296G (Ral 9006)YW297G (Ral 9007)YW278G (Ral 7048)
Test Conditions The results shown below are based on mechanical and chemical tests which (unless otherwise
indicated) have been carried out under laboratory conditions and are given for guidance only. Actual
product performance will depend upon the circumstances under which the product is used.
Page 1 of 3
Interpon D2525 ECO
2
Chemical Tests Acetic acid salt spray ISO9227 <16 mm corrosion/10cm, 1000 hours
Pass. No corrosion creep more than 1.6
Salt spray ASTM B117-85 (3000 hrs) mm from scribe. Minimum blister rating
8
Constant humidity ISO6260 No blistering, creep <1mm (1000 hours)
Pass 30 cycles no blistering, gloss
Sulphur Dioxide ISO3231
loss or discoloration
Pressure Cooker pass 1 hour no
Permeability EN12206:2004
blistering
Generally good resistance to acid,
Chemical Resistance alkalis and oil at normal temperatures
Mortar Resistance EN12206:2004 No effect after 24 hours
Solar reflective Increase in solar reflective properties with respect to standard formulations
properties
Colour Percent Increase in solar reflective Properties
Beige 5 to 10% (Depending on the shade)
Grey 33 to 350% ( Depending on Light to Dark Shade)
Blue 30%
Brown (Light to Dark) 90 to 247% ( Depending on Light to Dark Shade)
Black 540%
Metallic Grey 54 to 99% ( Depending on Light to Dark Shade)
Pretreatment For maximum protection it is essential to pretreat components prior to the application of Interpon
D2525 ECO Metallic.
Aluminium components should receive a full multi-stage chromate conversion coating or suitable
chrome-free pre-treatment or suitable pre-anodising to clean and condition the substrate.
Detailed advice should be sought from the pre-treatment supplier.
Galvanised steel requires surface preparation by either multi-stage pretreatment using either zinc
phosphate or chromate conversion or controlled sweep blasting. Depending on the type of
galvanizing, degassing or use of anti-bubbling additives may be required follow the procedural
advice of the pretreatment supplier.
Interpon D2525 ECO Metallic products may also be used on cast or mild steel. For outdoor use,
Interpon PZ anti-corrosive primer over a correctly prepared substrate is recommended.
Application Interpon D2525 ECO Metallic powders can be applied by manual or automatic electrostatic spray or
tribo-charging equipment. For solid shades, unused powder can be reclaimed up to a maximum of
30% using suitable equipment and recycled through the system. Please consult AkzoNobel for
further details as to the correct mixing ratio for virgin/reclaim powder.
All powders can show small colour differences from batch to batch, this is normal and unavoidable.
While AkzoNobel take every precaution to minimize visible differences, this cannot be guaranteed.
Applicators and fabricators are advised to use a single batch for parts that will be assembled
together. Differences are more likely with special effect powders.
Bonded products have better application properties than blended products (more stable) but attention
should still be paid to line settings in order to avoid marble effect and changes in aspect after
recycling. For more details it is suggested to read the Metallic Application Guideline.
Page 2 of 3
Interpon D2525 ECO
Different substrates (aluminium, steel, galvanized steel), use of primer, and big changes in film
thickness may give a different aspect.
Products with different codes should not be mixed even if same colour and gloss.
Post Application For specific advice on the suitability of post coating processes such as bending or the use of
sealants, adhesives, thermal break, cleaning etc, please consult AkzoNobel.
Maintenance For specific advice on Cleaning and Maintenance, please consult the Interpon D series Cleaning and
Maintenance Guidelines available from AkzoNobel.
Safety Precautions Please consult the Material Safety Datasheet (MSDS) available from AkzoNobel.
IMPORTANT NOTE: The information in this data sheet is not intended to be exhaustive and is based on
the present state of our knowledge and on current laws: any person using the product for any purpose
other than that specifically recommended in the technical data sheet without first obtaining written
confirmation from us as to the suitability of the product for the intended purpose does so at his own risk.
It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the
local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this
product if available. All advice we give or any statement made about the product by us (whether in this
data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or
the condition of the substrate or the many factors affecting the use and application of the product.
Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for
the performance of the product or for any loss or damage arising out of the use of the product. All
products supplied and technical advices given are subject to our standard terms and conditions of sale.
You should request a copy of this document and review it carefully. The information contained in this
data sheet is subject to modification from time to time in the light of experience and our policy of
continuous development. It is the user's responsibility to verify that this data sheet is current prior to
using the product.
Brand names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel.
Copyright 2015 Akzo Nobel Powder Coatings Ltd. Interpon is a registered trademark of AkzoNobel
Interpon D2525 ECO - Issue 3
Issued: 19/10/2016
Page 3 of 3
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
1.2 Relevant identified uses of the substance or mixture and uses advised against
Identified uses
Electrostatic coating for use in industrial plants
1.3 Details of the supplier of the safety data sheet
Firma Ad: Akzo Nobel Boya San. Ve Tic A..
Adresi: Ayhan Sok. No 17 Ege Serbest Blgesi
35410,Gaziemir zmir, Trkiye
Telefon No: +90.232.252.27.00
Fax No: +90.232.252.16.45
Supplier
Telephone number : +90 232 252 27 00
Hours of operation :
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 1/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 2/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
4.2 Most important symptoms and effects, both acute and delayed
There are no data available on the mixture itself. The mixture has been assessed following the conventional method
of the CLP Regulation (EC) No 1272/2008 and is classified for toxicological properties accordingly. See Sections 2
and 3 for details.
This takes into account, where known, delayed and immediate effects and also chronic effects of components from
short-term and long-term exposure by oral, inhalation and dermal routes of exposure and eye contact.
Coating powders can cause localised skin irritation in folds of the skin or under tight clothing.
4.3 Indication of any immediate medical attention and special treatment needed
Notes to physician : In case of inhalation of decomposition products in a fire, symptoms may be delayed.
The exposed person may need to be kept under medical surveillance for 48 hours.
Specific treatments : No specific treatment.
6.2 Environmental : Do not allow to enter drains or watercourses. If the product contaminates lakes,
precautions rivers, or sewers, inform the appropriate authorities in accordance with local
regulations.
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 3/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
6.3 Methods and material : Contain and collect spillage with an electrically protected vacuum cleaner or by wet-
for containment and brushing and place in container for disposal according to local regulations (see
cleaning up section 13). Do not use a dry brush as dust clouds or static can be created.
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 4/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
Recommended monitoring : If this product contains ingredients with exposure limits, personal, workplace
procedures atmosphere or biological monitoring may be required to determine the effectiveness
of the ventilation or other control measures and/or the necessity to use respiratory
protective equipment. Reference should be made to monitoring standards, such as
the following: European Standard EN 689 (Workplace atmospheres - Guidance for
the assessment of exposure by inhalation to chemical agents for comparison with
limit values and measurement strategy) European Standard EN 14042 (Workplace
atmospheres - Guide for the application and use of procedures for the assessment
of exposure to chemical and biological agents) European Standard EN 482
(Workplace atmospheres - General requirements for the performance of procedures
for the measurement of chemical agents) Reference to national guidance
documents for methods for the determination of hazardous substances will also be
required.
DNELs/DMELs
No DNELs/DMELs available.
PNECs
No PNECs available
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 5/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
Gloves : For prolonged or repeated handling, use the following type of gloves:
Vinyl gloves. (EN 374).
Nitrile gloves. (EN374).
The instructions and information provided by the glove manufacturer on use,
storage, maintenance and replacement must be followed. Barrier creams may help
to protect the exposed areas of the skin but should not be applied once exposure
has occurred.
The user must check that the final choice of type of glove selected for handling this
product is the most appropriate and takes into account the particular conditions of
use, as included in the user's risk assessment.
Body protection : Personnel should wear protective clothing. Care should be taken in the selection of
protective clothing to ensure that inflammation and irritation of the skin at the neck
and wrists through contact with the powder are avoided.
Other skin protection : Appropriate footwear and any additional skin protection measures should be
selected based on the task being performed and the risks involved and should be
approved by a specialist before handling this product.
Respiratory protection : If workers are exposed to concentrations above the exposure limit, they must use
appropriate, certified respirators.
Dry sanding, flame cutting and/or welding of the dry paint film will give rise to dust
and/or hazardous fumes. Wet sanding/flatting should be used wherever possible. If
exposure cannot be avoided by the provision of local exhaust ventilation, suitable
respiratory protective equipment should be used.
Environmental exposure : Do not allow to enter drains or watercourses.
controls
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 6/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
10.2 Chemical stability : Stable under recommended storage and handling conditions (see Section 7).
10.3 Possibility of : Under normal conditions of storage and use, hazardous reactions will not occur.
hazardous reactions
10.4 Conditions to avoid : When exposed to high temperatures may produce hazardous decomposition
products.
10.6 Hazardous : Under normal conditions of storage and use, hazardous decomposition products
decomposition products should not be produced.
This takes into account, where known, delayed and immediate effects and also chronic effects of components from
short-term and long-term exposure by oral, inhalation and dermal routes of exposure and eye contact.
Coating powders can cause localised skin irritation in folds of the skin or under tight clothing.
Acute toxicity
Conclusion/Summary : Not available.
Acute toxicity estimates
Not available.
Irritation/Corrosion
Conclusion/Summary : Not available.
Sensitisation
Conclusion/Summary : Not available.
Mutagenicity
Conclusion/Summary : Not available.
Carcinogenicity
Conclusion/Summary : Not available.
Reproductive toxicity
Conclusion/Summary : Not available.
Teratogenicity
Conclusion/Summary : Not available.
Specific target organ toxicity (single exposure)
Not available.
Specific target organ toxicity (repeated exposure)
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 7/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
Not available.
Aspiration hazard
Not available.
The mixture has been assessed following the summation method of the CLP Regulation (EC) No 1272/2008 and is
not classified as hazardous to the environment.
Conclusion/Summary : Not available.
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 8/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
Methods of disposal : The generation of waste should be avoided or minimised wherever possible.
Disposal of this product, solutions and any by-products should at all times comply
with the requirements of environmental protection and waste disposal legislation
and any regional local authority requirements. Dispose of surplus and non-
recyclable products via a licensed waste disposal contractor. Waste should not be
disposed of untreated to the sewer unless fully compliant with the requirements of
all authorities with jurisdiction.
Hazardous waste : Within the present knowledge of the supplier, this product is not regarded as
hazardous waste, as defined by EU Directive 91/689/EEC.
European waste : The European Waste Catalogue classification of this product, when disposed of as
catalogue (EWC) waste, is: 08 02 01
Packaging
Methods of disposal : The generation of waste should be avoided or minimised wherever possible. Waste
packaging should be recycled. Incineration or landfill should only be considered
when recycling is not feasible.
Disposal considerations : Using information provided in this safety data sheet, advice should be obtained from
the relevant waste authority on the classification of empty containers.
Empty containers must be scrapped or reconditioned.
Dispose of containers contaminated by the product in accordance with local or
national legal provisions.
Type of packaging European waste catalogue (EWC)
CEPE Paint Guidelines 15 01 01 Cardboard.
15 01 02 Plastic.
Special precautions : This material and its container must be disposed of in a safe way. Empty
containers or liners may retain some product residues. Avoid dispersal of spilt
material and runoff and contact with soil, waterways, drains and sewers.
14.4 Packing - - -
group
14.5 No. No. No.
Environmental
hazards
Additional - - -
information
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 9/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
14.6 Special precautions for : Transport within users premises: always transport in closed containers that are
user upright and secure. Ensure that persons transporting the product know what to do in
the event of an accident or spillage.
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 10/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
15.2 Chemical Safety : No Chemical Safety Assessment has been carried out.
Assessment
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 11/12
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II - Turkey
YW296G/20KG Interpon D2525 Matt Grey metallic Matt
Notice to reader
The information in this Safety Data Sheet is based on the present state of knowledge and current legislation.
It provides guidance on health, safety and environmental aspects of the product and should not be
construed as any guarantee of technical performance or suitability for particular applications. The product
should not be used for purposes other than those shown in Section 1 without first referring to the supplier
and obtaining written handling instructions. As the specific conditions of use of the product are outside the
suppliers control, the user is responsible for ensuring that the requirements of relevant legislation are
complied with. The information contained in this safety data sheet does not constitute the users own
assessment of workplace risks, as required by other health and safety legislation.
Date of issue/Date of revision : 29/2/2016 Date of previous issue : 23/10/2013. Version :2 12/12