You are on page 1of 4

Daimeter of pile (D) = 0.

50 m
Effective pile length from bottom of pile cap = 28.50 m
Height of GL from bottom of pile cap = 4.50 m
Depth of water table from GL = 1.75 m

Depth Length BH-01 BH-02 BH-03 BH-04 Average


0 - 3.55 m 3.55 Dry density 1.7 t/m^3
3.55 - 15.95 m 12.40 Submerged density 0.7 t/m^3
15.95 - 21.75 5.80 Submerged density 0.7 t/m^3
21.75 - 32.50 10.75 Submerged density 0.7 t/m^3
Total = 32.50

Depth Length BH-01 BH-02 BH-03 BH-04 Average


0 - 3.55 m 3.55 f 0 degrees
3.55 - 15.95 m 12.40 f 0 degrees
15.95 - 21.75 5.80 f 0 degrees
21.75 - 32.50 10.75 f 34 degrees
Total = 32.50

Depth Length BH-01 BH-02 BH-03 BH-04 Average


0 - 3.55 m 3.55 c 0 t/m^2
3.55 - 15.95 m 12.40 c 3.5 t/m^2
15.95 - 21.75 5.80 c 8 t/m^2
21.75 - 32.50 10.75 c 0 t/m^2
Total = 32.50

Qu(ultimate) = Ap*(0.5 * D * g * Ng + Pd * Nq) + Sum (K i to d * Pdi * tand * Asi) +


Ap * (c * Nc) + a * Ci * Asi

Cross sectional area of pile (Ap) = 0.19625 m^2


Unit weight of soil above water table = 1.7 t/m^3
Effective unit weight at soil at pile toe = 0.7 t/m^3
Cohesion at pile toe = 0.00 t/m^2
For f = 0 degrees Ng = 32.1 Nq = 31.4 Nc = 9
Overburden pressure at bottom of pile cap (Pd0) = 7.65 t/m^2
Overburden pressure (Pd1) = 2.98 t/m^2
Overburden pressure (Pd2) = 21.88 t/m^2
Total overburden pressure (Pd) = 24.85 t/m^2

Point resistant (Rb) = Ap*(0.5 * D * g * Ng + Pd * Nq) + 154.23 t


Ap * (c * Nc)

Adopt value of K = 1.50 & d=f tan d = 0.000


a= 0.50 Average Ci = 0.00 t/m^2
As1 = -4.32 m^2
As2 = 49.09 m^2
As = As1 + As2 44.77 m^2
Average overburden pressure for upper part of pile = 5.31 t/m^2
Average overburden pressure for lower part of pile = 13.91 t/m^2
Skin friction resistant (fs1) = 0.00 t
Skin friction resistant (fs2) = 0.00 t

Total skin friction resistant (Rs) = a * Ci * Asi + 0.00 t


Sum (K i to d * Pdi * tand * Asi)

Total bearing resistant (Rb + Rs) = 154.23 t (A)

Allowable bearing resistant Qu(allow.) = FOS = 2.5 61.69 t


Limiting the overburden pressure upto 20 times of dia. of pile, i.e. 10 m
Actual length of pile provided = 28.50 m
and assuming water table reach the GL, Hence gsubmerged = 0.7 t/m^3
Maximum overburden pressure = 7 t/m^2
Adopt value of K = 1.5 & d=f tan d = 0.000
As = 44.77 m^2
Total skin friction resistant (Rs) = a * Ci * Asi + 0.00 t
Sum (K i to d * Pdi * tand * Asi)
Total bearing resistant (Rb + Rs) = 154.23 t (B)

Allowable bearing resistant Qu(allow.) = FOS = 2.5 61.69 t

Also ignoring the Ng effect in point bearing, Rb = 43.14 t

Total bearing resistant (Rb + Rs) = 43.14 t (C )

Allowable bearing resistant Qu(allow.) = FOS = 2.5 17.25 t

Allowable load for 28.5 m long pile = Qu/ 1.5 11.50 t

Uplift resistant = Skin resistant of pile/2 FOS = 2.5 0.00 t


Depth of pile cap bottom from GL = 4.5 m
Diameter of pile = 0.5 m

Depth (m) Density (t/m^3)


Layer No. Above WL Below WL Cum. total Above WL Below WL Average C Average p X-sec area
I 1.75 1.8 3.55 1.7 0.7 0 0 0.19625
II 0 12.4 15.95 1.7 0.7 3.5 0 0.19625
III 0 5.8 21.75 1.7 0.7 8 0 0.19625
IV 0 10.75 32.5 1.7 0.7 0 34 0.19625
V 0 0 32.5 1.7 0.7 0 34 0.19625
VI

Point resistant (t) Skin resistant (t)


Layer No. Nc Nq Ng 0.5*D*g*Ng Pd*Nq c*Ap*Nc Total Sum(K*Pdi*Asi)
I 0 1 0
II 9 1 0
III 9 1 0
IV 0 33.3 48.03
V 0 33.3 48.03
VI
Overburden pressure (t/m^2)
Shaft length Peri. Area Layer top Layer bottom Average
0 0.000 0.000 4.235 2.118
11.45 17.986 4.235 12.915 8.575
5.8 9.111 12.915 16.975 14.945
10.75 16.886 16.975 24.500 20.738
0 0.000 24.500 24.500 24.500

Skin resistant (t)


a*Ci*Asi Total

You might also like