You are on page 1of 11

PROJECT : PROPOSED INTERIOR FITOUT FOR FOR WEWORK, GURGAON

BILL OF QUANTITIES FOR INTERIOR ELECTRIFICATION WORK


REV. NO : R0
DATE: 11.08.2017

SI.NO DESCRIPTION UNIT QTY.

SECTION A: LT PANELS

1
Supply, receiving, unloading, shifting to indoor Electrical rooms, inspection,
handling, assembly, installing in correct aligned position, making proper
connections, testing and commissioning of the following LT Panels including
alignment leveling, grouting with anchor fasteners, GI nuts and bolts and
making of all incoming and outgoing feeders with approved aluminum
engraved name plates complete as required by Project Managers/Consultant.
All materials and workmanship shall conform to latest Indian standards /
Consultants technical specifications /tender drawings and shall comply with
statutory requirements.

Note: Please refer enclosed Single line diagrams for LT Panels .

1.1 LT SWITCH BOARDS (As per enclosed technical specifications Ref No.-
100 & SLD Ref No.- WW - ELEC-100)
3 phase, 4wire, floor mounting free standing / Wall mounted, cubicle type, LT
switchboards.

a Main Distribution Panel Nos. 1


b. UPS Output Panel Nos. 1
c. GF Raw Power panel Nos. 1
d. 1F Raw Power panel Nos. 1
e. 4F Raw Power panel Nos. 1
f. 5F Raw Power panel Nos. 1
g. 7F Raw Power panel Nos. 1
h. GF UPS Panel Nos. 1
i. 1F UPS Panel Nos. 1
j. 4F UPS Panel Nos. 1
k. 5 &7F UPS Panel Nos. 1

1.2 ISOLATORS IN POWDER COATED MS ENCLOSURES (As per enclosed


technical specifications)

a.
16A TP + NL,10kA, C Curve MCB in IP-52 Powder coated MS enclosure. Nos. 8

b.
25A TP + NL, 10kA, C Curve MCB in IP-52 Powder coated MS enclosure. Nos. 6

c.
20A TP + NL, 10kA, C Curve MCB in IP-52 Powder coated MS enclosure. Nos. 1

d.
32A TP + NL, 10kA, C Curve MCB in IP-52 Powder coated MS enclosure. Nos. 2

e.
40A TP + NL, 10kA, C Curve MCB in IP-52 Powder coated MS enclosure. Nos. 11

f.
63A TP + NL, 10kA, D Curve MCB in IP-52 Powder coated MS enclosure. Nos. 6

g. 125A, 415V, 3P+2NL, TM based, adjustable O/L and Fixed SC, 25kA MCCB
Nos. R0
in IP-52 Powder coated MS enclosure.
h. 63A TP + 2NL, TM based, adjustable O/L and Fixed SC, 16kA, MCCB in IP-
Nos. R0
52 Powder coated MS enclosure.
I 400A isolator in IP-52 Powder coated MS enclosure with indication( UPS input
Nos. 1
side).

SUB TOTAL

2.0 LT POWER & CONTROL CABLES


2.1 Supply, laying, Dressing, Clamping, Testing & Commissioning of 1.1kV grade
XLPE / PVC insulated, PVC sheathed Aluminium/Copper conductor cable
conforming to specification. The cables shall be laid on trays / in pipes /
clamped to wall/ceiling.

2.1.1 3.5 Core XLPE insulated, Al conductor Cables

a. 3.5C x 185 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. 80
Cable. (A2XFY)
b. 3.5C x 150 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. R0
Cable. (A2XFY)
c. 3.5C x 120 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. R0
Cable. (A2XFY)
d.
3.5C x 95 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. 80
Cable. (A2XFY)

e.
3.5C x 70 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. 420
Cable. (A2XFY)

f. 3.5C x 50 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed


Mtrs. 340
Cable. (A2XFY)
g. 3.5C x 35 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. R0
Cable. (A2XFY)
h. 3.5C x 25 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. R0
Cable. (A2XFY)

BOQ Page 1 of 11 RSP Design Consultants(I) Pvt. LTD


SI.NO DESCRIPTION UNIT QTY.

2.1.2 4C & 3C XLPE insulated, Al conductor Cables

a 4C x 25 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed


Mtrs. R0
Cable. (A2XFY)
b 4C x 16 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. 50
Cable. (A2XFY)
c 4C x 10 Sq.mm Al. Conductor, XLPE insulated, Armoured, PVC sheathed
Mtrs. 1000
Cable. (A2XFY)
d 4C x 6 Sq.mm Al. Conductor,XLPE insulated, Armoured, PVC sheathed
Mtrs. R0
Cable. (A2XFY)
e 4C x 4 Sq.mm Al. Conductor, XLPE insulated, armoured & PVC sheathed
Mtrs. R0
cable.

2.1.3
4C, 3C & 1C XLPE insulated, Cu conductor, PVC Outer sheathing Cables

a 4C x 10 Sq.mm Cu.conductor, PVC insulated, armoured & PVC Mtrs. R0


sheathed cable (YFY).
b 4C x 6 Sq.mm Cu.conductor, PVC insulated, armoured & PVC Mtrs. 230
sheathed cable (YRY).
c. 3C x 6 Sq.mm Cu.conductor, PVC insulated, armoured & PVC
Mtrs. 220
sheathed cable (YRY).
d. 4C x 4 Sq.mm Cu.conductor, PVC insulated, armoured & PVC Mtrs. 360
sheathed cable (YRY).
e. 3C x 4 Sq.mm Cu.conductor, PVC insulated, armoured & PVC Mtrs. R0
sheathed cable (YRY).
f. 1C x 50 Sq.mm PVC insulated Flexible Copper Cable (YY). Mtrs. 200
g. 16 sq. MM FRLS grade MSCC wires for UPS DB Earthing including end
Mtrs. R0
termination
h. 10 sq. MM FRLS grade MSCC wires for UPS D Earthing including end
Mtrs. 250
termination
i.
6 sq. MM FRLS grade MSCC wiresfor Earthing including end termination. Mtrs. 100

j. 4 sq. MM FRLS grade MSCC wires for SRG Earthing including end
Mtrs. R0
termination.

2.2 LT CABLE TERMINATION

Supply, installation, testing and commissioning of end termination for cables


1.1KV grade XLPE / PVC insulated Cu./ Al. conductors. DOUBLE
compression glands shall be used for cable sizes above 70 sq.mm and
SINGLE compression brass cable glands for sizes upto 70 sq.mm. The
termination shall include earth tags, crimping type tinned copper lugs and
consumables for the following size of cables.

BOQ Page 2 of 11 RSP Design Consultants(I) Pvt. LTD


SI.NO DESCRIPTION UNIT QTY.

2.2.1 3.5 Core XLPE insulated, Al conductor Cables

b. 3.5C x 185 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Set 4
Cable. (A2XFY)
c. 3.5C x 150 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Set R0
Cable. (A2XFY)
d. 3.5C x 120 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Set R0
Cable. (A2XFY)
e 3.5C x 95 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Set 4
Cable. (A2XFY)
f 3.5C x 70 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Set 10
Cable. (A2XFY)

g 3.5C x 50 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed


Set 8
Cable. (A2XFY)
h 3.5C x 35 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Set R0
Cable. (A2XFY)
i. 3.5C x 25 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Set R0
Cable. (A2XFY)

2.2.2 4C & 3C XLPE insulated, Al conductor Cables

a 4C x 25 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed


Set R0
Cable. (A2XFY)
b 4C x 16 Sq.mm Al. conductor, XLPE insulated, Armoured, PVC sheathed
Set 6
Cable. (A2XFY)
c 4C x 10 Sq.mm Al. Conductor, XLPE insulated, Armoured, PVC sheathed
Set 86
Cable. (A2XFY)
d 4C x 6 Sq.mm Al. Conductor,XLPE insulated, Armoured, PVC sheathed
Set R0
Cable. (A2XFY)
e 4C x 4 Sq.mm Al. Conductor, XLPE insulated, armoured & PVC sheathed
Set R0
cable.

2.2.3
4C, 3C & 1C XLPE insulated, Cu conductor, PVC Outer sheathing Cables

a 4C x 10 Sq.mm Cu.conductor, PVC insulated, armoured & PVC Set


sheathed cable (YFY).
b 4C x 6 Sq.mm Cu.conductor, PVC insulated, armoured & PVC Set 16
sheathed cable (YRY).
c. 3C x 6 Sq.mm Cu.conductor, PVC insulated, armoured & PVC
sheathed cable (YRY). Set 8

d. 4C x 4 Sq.mm Cu.conductor, PVC insulated, armoured & PVC Set 20


sheathed cable (YRY).
e. 3C x 4 Sq.mm Cu.conductor, PVC insulated, armoured & PVC Set
sheathed cable (YRY).
f.
1C x 50 Sq.mm PVC insulated Flexible Copper Cable (YY). Set 30

SUB TOTAL

3.0 CABLE TRAYS (As per enclosed technical specifications.)

Factory fabricated, cable trays made out of 2/ 1.6mm thick Pre- galvanized
sheet steel using proper jigs and fixtures, including all necessary accessories
such as bends, tees, reducers, coupler plates, fasteners etc. Cable tray
sections shall be joined by fish plates. The tray shall be supported at regular
intervals of not more than 1.5/ 2 metre using engineered punched angle
supports / high - tech threaded rods (for 300mm width trays and lesser tray
width) as per enclosed technical specification (Profab Make or equivalent).The
GI tray supports shall be suitable for metal roof with necessary clamps and
fixing accessories.

3.1 Ladder Type Cable Trays (2mm Thick).


a 750mm W x 70mm H Mtrs. 40
b. 600mm W x 70mm H Mtrs. R0
c. 450mm W x 70mm H Mtrs. R0
d. 300mm W x 50mm H Mtrs. R0
e 200mm W x 50mm H Mtrs. R0
f 150mm W x 50mm H Mtrs. R0

3.2 Perforated Type Cable Trays (1.6mm Thick).

PERFORATED TYPE fabricated from 1.6mm thick Pre-galvanised sheet and


with 1.6mm thick unperforated covers. Complete Tray accessories should
include factory made bends, suitable angle supports, Anchor fasteners and
hardwares. Complete Tray accessories should include suitable MS hot dip
galvanized punched angle supports. The GI tray supports shall be suitable for
metal roof with necessary clamps and fixing accessories.

a 300mm W x 50mm H Mtrs. R0


b 150mm W x 50mm H Mtrs. 180
c 200mm W x 50mm H Mtrs. 35
c 100mm W x 50mm H Mtrs. 935
c 50mm W x 50mm H Mtrs. 1960

SUB TOTAL

BOQ Page 3 of 11 RSP Design Consultants(I) Pvt. LTD


SI.NO DESCRIPTION UNIT QTY.

4 CEILING SUSPENDED / FLOOR RACEWAYS (As per enclosed technical


specification)

Supply and installation of Race ways of following sizes made of 1.6 mm thick
pre galvanized sheet steel (Perforated wherever specified) with 1.2 mm thick
screwed / Push to fit type cover. The race ways shall be similar to Profab
make UT range & shall be suitable for installation in floor screed / above false
ceiling / open ceiling areas. The joining accessories shall be of same material
supplied along with race ways. Approval shall be obtained from consultants on
product sample before procurement.

4.1 CEILING SUSPENDED RACEWAYS


a 400mm x 40mm Ceiling raceways with 2 barriers. Mtrs. R0
b 300mm x 40mm Ceiling raceways with 2 barriers. Mtrs. 145
c 200mm x 40mm Ceiling raceways with 2 barriers. Mtrs. 110
d 150mm x 40mm raceways without central barrier. Mtrs. 160
e 100mm x 40mm raceways without central barrier. Mtrs. 890
4.2 FLOOR RACEWAYS: Raceway size made of 2.0mm thick pre galvanized
sheet steel (Perforated wherever specified) with 2mm thick clamped /
screwed Cover.
a 400mm x 40mm Floor raceways with 2 barriers. Mtrs. R0
b. 300mm x 40mm Floor raceways with 2 barriers. Mtrs. R0
c 200mm x 40mm Floor raceways with 2 barriers. Mtrs. R0
d 150mm x 40mm raceways without central barrier. Mtrs. 50
e 100mm x 40mm raceways without central barrier. Mtrs. 80

4.3 JUNCTION BOXES FOR CEILING RACE WAYS


Supply and installation of Junction boxes of the following sizes made of 1.6
mm thick screwed covers. The junction boxes shall be fabricated of same
material as race ways.
Note: Junction box for ceiling raceways not taken.
a 410mm x 410mm x 50mm junction box with cover Nos R0
b 310mm x 310mm x 50mm junction box with cover Nos R0
c 210mm x 210mm x 50mm junction box with cover Nos R0
d 160mm x 160mm x 50mm junction box with cover Nos R0
e 110mm x 110mm x 50mm junction box with cover Nos R0

4.4 JUNCTION BOXES FOR FLOOR RACE WAYS.


Supply and installation of Junction boxes of the following sizes made of 2.0
mm thick screwed covers. The junction boxes shall be fabricated of same
material as race ways.

a 410mm x 410mm x 50mm junction box with cover Nos. R0


b 310mm x 310mm x 50mm junction box with cover Nos. R0
c 210mm x 210mm x 50mm junction box with cover Nos. R0
d 160mm x 160mm x 50mm junction box with cover Nos. 3
e 110mm x 110mm x 50mm junction box with cover Nos. 96

5 FLOOR SCREED CUTTING FOR RACEWAYS AND JUNCTION BOXES

Cutting of floor screeding for accommodating the floor raceways/Conduits for


the following size raceways/junction boxes/conduits. The rate shall include
closing of extra gap with cement mortar & making good to the original level.

5.1 SCREED CUTTING FOR FLOOR RACEWAYS


a. 300mm x 40mm - wih 2Nos of central barriers Mtrs
b. 200mm x 40mm - with 1No central Barrier Mtrs
c. 150mm x 40mm - without barrier Mtrs 50
d. 100mm x 40mm - without barrier Mtrs 80

5.2 SCREED CUTTING FOR JUNCTION BOXES


a. 310 x 310 x 50mm junction box No's R0
b. 210 x 210 x 50mm junction box No's R0
c. 160 x 160 x 50mm junction box No's 3
d. 110 x110 x 50mm junction box No's 96

5.3 CONDUITS .
a. 32Mmm dia conduit ( Ceiling ) Mtrs 1660
b. 32Mmm dia conduit ( Floor ) Mtrs 590

5.3a Screed cutting for Conduits


a. 32mm dia conduit Mtrs 590
b. 25mm dia conduit Mtrs R0

SUB TOTAL

TOTAL FOR SECTION A

B SECTION B: DISTRIBUTION BOARDS AND SOCKETS

1 DISTRIBUTION BOARDS

Surface mounting double door type MCB DBs conforming to the specification
and fabricated out of CRCA sheet with powder coated to RAL 7032 lockable
hinged glazed front door, cable gland plate, conduit knockouts. The DBs shall
comprise of 63A Neutral terminal block for incomer, insulated fork type phase
bus bars, independent neutral terminal bar for each phase where required,
common insulated earth terminal bar and complete with interconnecting wiring.
The IP class shall be 31 or better. The rate shall include costs of MCB /
RCCB / RCBO.

1.1 UPS Power Distribution Board:


a 4 Tier/Row 56 Module MCB DB For Work stations PC Load (UDB).
4 tier/row 56 module MCB DB with 63A rated SP neutral terminal block,
insulated fork type 2P 12Module RYB bus bars, 3nos. Neutral terminal bars &
common earth terminal bar with insulated supports. (3 Phase seggregated DB
for DP outgoings --Workstation UPS DB's).
1 No. 63A, TP +2 NL, MCB type isolator(main incomer). + 3nos 40A DP, MCB
(Phase incomers).

3 Nos. of din rail mounting type SPD, 1.5kV, 15kA, DP Surge protection device
for each phase incomer.

21 Nos. 16A DP, 'D' curve MCB's for Outgoings

4 Tier/Row 56 Module MCB DB For Work stations PC Load(UDB) as


Nos. 14
above.

BOQ Page 4 of 11 RSP Design Consultants(I) Pvt. LTD


SI.NO DESCRIPTION UNIT QTY.

b.
6Way TPN Phase segregated DB with cable ties for cable management and
Top & Bottom removable gland plates with knockouts, suitable for TP MCB as
main incomer, DP `D' Type MCBs as phase incomer and `D' Type DP MCBs
Nos. R0
as outgoings with separate neutral bus for each phase. Common earth bus
and insulated bus bars and interconnecting wiring and incoming neutral bus
shall be rated 100A Copper.

1.2
Raw Power Distribution Board: (As per enclosed technical specification)

a 4 Tier/Row 40 Module MCB DB


4 tier/row 40 module MCB DB with 63A rated TP & neutral terminal block,
insulated fork type 1 Pole 12/ Module RYB bus bars, 3 nos. Neutral terminal
bars & common earth terminal bar with insulated supports (Phase segregated
DB for SP outgoings).
1 No. 63A, TP+NL MCB type isolator ( Main incomer),
3 Nos. 40A DP, 100mA, Si type RCCB ( Phase incomer ).
18 Nos. 6A / 10A / 16A / 20A SP, 10kA ,'C' Curve MCB's.

4 Tier/Row 40 Module MCB DB as above Nos. 5

b. 2 Tier/Row 28 Module MCB DB


2 tier/row 28 module MCB DB with 40A rated DP neutral terminal block, .
Neutral terminal bars & common earth terminal bar with insulated supports. (3
Phase seggregated DB for DP outgoings Hub room UPS DB's).

1 No. 63A, TP+NL MCB type isolator ( Main incomer),


3 Nos. 40A DP, 100mA, Si type RCCB ( Phase incomer ).
18 Nos. 6A / 10A / 16A / 20A SP, 10kA ,'C' Curve MCB's.

2 Tier/Row 28 Module MCB DB Nos. R0

SUB TOTAL

2 POWDER COATED FRAME FOR MCB DB's (AS PER ENCLOSED


DRAWING)

Frame with wire ways shall be made out of 16SWG CRCA sheet steel and
powder coating colour shall match the colour of MCB DB's. 200mm x 200mm
wire ways / Raceway with 2mm thick screwed / press to fit cover for making
Frame for MCB DB's. Complete required including installation accessories.

a. Type-1 DB Cabinet frame for 5 nos of 4 tier 56 module, 1 no. of 4 tier 40


Set. 1
module, 1 No. 2 tier 14 module.
b. Type-2 DB Cabinet frame for 6 nos of 4 tier 56 module, 1 no. of 4 tier 40
Set. 1
module, 1 No. 2 tier 14 module.
c. Type-3 DB Cabinet frame for 4 nos of 4 tier 56 module, 1 no. of 4 tier 40
Set. 2
module, 1 No. 2 tier 14 module.
d. Type-4 DB Cabinet frame for 1 nos of 4 tier 56 module, 2 no. of 4 tier 40
Set. 1
module, 1 No. 2 tier 14 module.

SUB TOTAL

3 RAW POWER & UPS SOCKETS:

Supply, installation, testing & commissioning of 240/ 415V, single/ three


phase decorative type switches sockets outlet complete with front plate
housed in passivated steel enclosure and all required accessories complete in
all respect. All power sockets should have white or approved color front plate
OR As approved by project in-charge / client / Consultant. The rate shall also
include cost of providing numbered stickers on the switch plates.

4.1 RAW POWER SOCKETS: (As per enclosed technical specification)

a 1 No. 6/16A round 6 pin RP Universal socket outlet controlled by 16A SP


switch on a common switch plate for general purpose. (1Socket + 1Switch in Nos. 113
3 Module).
b 1 No. 6A round 5 pin RP Universal socket outlet controlled by 10A SP switch
Nos. R0
on a common switch plate. .(1Socket + 1 Switch in 3 Module).
c 1 No. 16A, 6 PIN WHITE COLOR RP ROUND SOCKET OUTLET
CONTROLLED BY A 16A SP SWITCH -RAW POWER FOR PANTRY Nos. 22
EQUIPMENT (WEATHER PROOF).

4.2 Modular Metal Boxes for Raw power outlets


a Zinc passivated metal box suitable for item No.4.1 (a) Nos. 28
b Zinc passivated metal box suitable for item No.4.1 (b) Nos.
c. Zinc passivated metal box suitable for item No.4.1 (c.) Nos. 6

4.3 UPS POWER SOCKETS: (As per enclosed technical specification)


Approval shall be obtained from consultants on product sample before
procurement.
a.
3 Nos. 6/13A Intel socket outlets controlled by 16A SP common switch. Nos. R0

b. 2 Nos. 6/16A, round 6 pin coloured socket outlets each controlled by


Nos. 1605
individual16A SP switch on a common switch plate.
c. 1No. 6/13A Intel socket outlets controlled by 16A SP common switch for work
Nos. 63
stations.
d. 1 No. 6A Round 3 pin socket outlet for VAV units and fire dampers. Nos. 175
e. 1 No three phase.32A, 3pin moulded industrial type Plug and socket controlled
by inter-lockable type isolator similar to legrand make product code 56669
socket indoor type enclosure. Legrand product code:56323 type plug or Nos. R0
approved Equivalent (Server racks ).
f.
1 No single phase.32A, 3pin moulded industrial type Plug and socket
controlled by inter-lockable type isolator similar to legrand make product code
56669 socket indoor type enclosure. Legrand product code:56323 type plug or Nos. 20
approved Equivalent ( Hub racks + ISP + N/W+SER. Racks).

4.4 Modular Metal Boxes for UPS power outlets


d Zinc passivated metal box suitable for item No.4.3 (d) Nos. R0
e Zinc passivated metal box suitable for item No.4.3 (e) Nos. 1605
h Zinc passivated metal box suitable for item No.4.3 (h) Nos. 16
l Zinc passivated metal box suitable for item No.4.3 (l) Nos. 175
m Zinc passivated metal box suitable for item No.4.3 (m) Nos. R0

4.5 INDUSTRIAL TYPE POWER SOCKETS: (As per enclosed technical


specification)

BOQ Page 5 of 11 RSP Design Consultants(I) Pvt. LTD


SI.NO DESCRIPTION UNIT QTY.

Supply, installation, testing & commissioning of 240/ 415V, single/ three


phase industrial type socket outlets and all required accessories complete in
all respect. Approval shall be obtained from consultants on product sample
before procurement.

a 32A, 1 Phase 3pin IP44 Indoor type industrial interlocked plug & socket with
32A DP MCB in a single unit Similar to Mennekes make : 7213 or Approved Nos. R0
equivalent. with all fixing accessories.
c
1 no., 32A, 3 phase 5 pin,TP+NE weather proof Industrial plug and socket
with interlock switch in single unit similar to Nos. R0
Mennekes make : 5608, Legrand, Schneider or approved equivalent.(IP67)

4.6 FLOOR OUTLET BOXES


8 gang flush mounting box - 892 99 Nos. R0
8 gang frame - 892 92 Nos. R0

b. Floor POPUP box for fixing the power and data points ( 2nos 6/16A UPS
socket controlled by individual 16A switches and 1no. Data outlet ). Legrand Nos. 36
Make.

4.7 GI OUTLET BOXES FOR VOICE / DATA FACE PLATES.


Providing and fixing of factory fabricated 1.6 mm thick GI outlet boxes for
1Node / 2Nodes / 3Nodes / 4Nodes Voice / Data (N/W) face plates. For Wi-Fi,
Security system
a 1N, 1.6mm thick GI outlet box. Nos. R0
b 2N, 1.6mm thick GI outlet box. Nos. R0

SUB TOTAL

5.0 POWER CIRCUIT WIRING FOR SMALL POWER

Supply, installation, testing and commissioning Power wiring from Raw power
& UPS power DBs to power sockets with 660V FRLS insulated multi strand
copper wires in conduits / Raceways including termination in sockets/ MCBs.

I) Wire ends to be soldered at all termination in MCB DBs/ socket points

ii) Ferrules at both the ends


iii) Insulation sleeves over the lugs as required

iv) Insulation sleeves for flexible wires as required in the workstation partitions.

b. 3C x 4 Sq.mm double insulated, unarmoured copper FRLS flexible cable in


already laid Wireway / conduits with ferrules and pin type lugs for both the Mtrs. R0
ends. For server racks power.
c. 3 Run of 2.5 Sq.mm copper FRLS wires in already laid conduits with ferrules
Mtrs. 7500
and pin type lugs for both the ends.
d. 3 Run of 4 Sq.mm copper FRLS wires in already laid conduits with ferrules
Mtrs. 200
and pin type lugs for both the ends.
e. 2 Runs of 4 Sq.mm + 1Run 2.5sqmm copper FRLS wires in already laid
Mtrs. R0
conduits with ferrules and pin type lugs for both the ends.
SUB TOTAL

6.0 CONDUITS FOR POWER CIRCUITS.


1.78mm thick, heavy gauged, hot dip galvanized threaded GI /MS Conduits/
2mm thick FRLS PVC pipes with cast iron junction boxes, and lapp make end
couplers complete with all required accessories for wiring (as per
specifications and drawings).

6.1 GI Conduits:
a. 25mm dia GI conduit Mtrs. R0

6.2 MS Conduit:
a. 25mm dia MS conduit Mtrs. R0

6.3 FRLS PVC Conduit:


a 20mm dia FRLS PVC conduit Mtrs. R0
b 25mm dia FRLS PVC conduit Mtrs. R0
c. 25mm dia steel reinforced PVC flexible conduit with end couplings. Mtrs. 50

6.4 CONDUITS FOR DATA / VOICE / AV cable


a 25mm dia FRLS PVC conduit Mtrs. 100

SUB TOTAL

TOTAL FOR SECTION B

C SECTION-C: LIGHTING DISTRIBUTION BOARDS AND LIGHT FIXTURES

1
Lighting Distribution Board: (As per enclosed technical specification)

a 4 Tier/Row 56 Module MCB DB


4 tier/row 56 module MCB DB with 63A rated TP & neutral terminal block,
insulated fork type 1 Pole 12 Module RYB bus bars, 3 nos. Neutral terminal
bars & common earth terminal bar with insulated supports (Phase segregated
DB for SP outgoings).
1 No. 63A, TPN, 10kA , 'B' Curve MCB + 3nos.,40A DP, 10kA , 30mA, 10KA,
Si type RCCB .
33/ 24/18 Nos. 6A / 10A / 16A / 20A SP, 10kA, 'B' Curve MCB's.
4 Tier/Row 56 Module MCB DB as above. Nos. 6

b. 4 Tier/Row 40 Module MCB DB


4 tier/row 4 module MCB DB with 63A rated TP & neutral terminal block,
insulated fork type 1 Pole 6 Module RYB bus bars, 3 nos. Neutral terminal
bars & common earth terminal bar with insulated supports (Phase segregated
DB for SP outgoings).
1 No. 63A, TPN, 10kA , 'B' Curve MCB + 3nos.,40A DP, 10kA , 30mA, 10KA,
Si type RCCB .
18 Nos. 6A / 10A / 16A / 20A SP, 10kA, 'B' Curve MCB's.
4 Tier/Row 40 Module MCB DB as above. Nos. 1

SUB TOTAL

2 Emergency Lighting Distribution Board: (As per enclosed technical


specification)

a 1 tier / row 14 module MCB DB with 1 pole 14 module insulated fork bus bar,
Neutral, earth terminal block with supports (1-Phase SP outgoing Circuits).For Nos. 5
Emergency Lighting.

BOQ Page 6 of 11 RSP Design Consultants(I) Pvt. LTD


SI.NO DESCRIPTION UNIT QTY.

b 2 tier / row 28 module MCB DB with 1 pole 28 module insulated fork bus bar,
Neutral, earth terminal block with supports (1-Phase DP outgoing Circuits) for Nos. R0
Main Emergency lighting DB.

SUB TOTAL

4 CIRCUIT WIRING FOR LIGHTING

Supply and installation of circuit wiring with 660V FRLS insulated multi
strand copper wires in already laid conduits including terminations.

a 3 Run of 1.5 Sq.mm copper FRLS wires in already laid conduits with ferrules
and pin type lugs for both the ends. Mtrs. R0

b 2 Run of 2.5 Sq.mm+ 1Run of 1.5sq.mm copper FRLS wires in already laid
Mtrs. 26250
conduits with ferrules and pin type lugs for both the ends.

SUB TOTAL

5 POINT WIRING

Supply and installation of Point Wiring for light points with 660V grade multi
strand flexible copper wires 3 run 2.5 sq. mm, 25mm dia 2mm thick FRLS
PVC conduits, PVC reinforced flexible conduits with end couplers and conduit
accessories and decorative modular type switches in zinc passivated switch
box, switches and front cover etc., complete in all respect.

(The rate of MCB shall not included in point wiring item)


a One light point controlled by one no. 6A SP Switch. Nos. 411
b Two light point controlled by one no. 6A SP Switch. Nos. 112
c Three light point controlled by one no. 6A SP Switch. Nos. 80
d Four light point controlled by one no. 6A SP Switch. Nos. 15
e Five light point controlled by one no. 6A SP Switch. Nos. 4
f Six light point controlled by one no. 10A SP Switch. Nos. 4
g Seven light point controlled by one no. 10A SP Switch. Nos. 1
h Eight light point controlled by one no. 10A SP Switch. Nos. R0
I Nine light point controlled by one no. 10A SP Switch. Nos. R0
j ten light point controlled by one no. 10A SP Switch. Nos. R0

k. One exhaust fan point controlled by one 6A switch and one socket near the
Set R0
exhaust fan.
l. One Wall mounted fan point controlled by one 6A switch and one socket near
Set R0
the exhaust fan.

SUB TOTAL

6 CONDUITS / SUPPORTING MATERIALS FOR INTERNAL LIGHTING


MS/ FRLS PVC / GI CONDUITS

Supply and installation of PVC FRLS conduit having 2mm wall thickness,
Block enameled MS conduit having 1.6mm wall thickness and GI conduit
having 360gms/ sq. mt. Zinc coating (As per IS standards) with complete
conduit accessories and fixing accessories etc.

6.1 GI Conduits:
a. 25mm dia GI conduit Mtrs. R0

6.2 MS Conduit:
a. 25mm dia MS conduit Mtrs. 100

6.3 FRLS PVC Conduit:


a 20mm dia FRLS PVC conduit Mtrs. R0
b 25mm dia FRLS PVC conduit Mtrs. 500
c. 20mm dia steel reinforced PVC flexible conduit with end couplings. Mtrs. R0

SUB TOTAL

7 LIGHT FIXTURES: OFFICE AREA


a.
Installation of light fixture with APF electronic driver (driver shall be complied
for less than 10% THD & >0.95PF). The installation cost includes all
necessary light fixtures supporting items. Type ref : similar to Philips Nos. 550
make:DN192B LED9S. - ( All Light fixtures except toilet area will be supplied
by client).
b. Installation of Occupancy sensor ( All Occupancy sensor except toilet area
Nos. 484
will be supplied by client).

BOQ Page 7 of 11 RSP Design Consultants(I) Pvt. LTD


SI.NO DESCRIPTION UNIT QTY.

7.1 LED LIGHT FIXTURES TOILET AREA


a
Supply, installation, testing and commissioning of 15W LED recess mounted
circular down light fixture with APF electronic driver (driver shall be complied
for less than 10% THD & >0.95PF). The installation cost includes all Nos. 106
necessary light fixtures supporting items. Type ref : similar to Philips
make:DN192B LED9S. - Toilet area.
b Supply, installation, testing and commissioning of Occupancy sensor Toilet
Nos. 65
area.

SUB TOTAL

8 SUPPLY, INSTALLATION, TESTING & COMMISSIONING OF INVERTER


As per enclosed technical specification
Inverter:

a
3-Phase input & 3 Phase output 10kVA Line interactive type inverter with 90
Minutes Battery Backup and Protections for Incoming and outgoing Circuits.
The batteries shall be placed in cabinet. The batteries shall be
VRLA+AGM+GEL type SMF batteries. Technical specifications approval shall
be obtained from Consultants along with offer submittals. The battery shall be
provided in 2mm thick MS powder coated rack. The inverter /batteries shall Nos. 1
comply to relevant standards/codes. The inverter design Output PF shall not
be less than 0.95PF. Inverter efficiency shall be 93% or more. The complete
equipment shall be supplied as per enclosed SLD. Make of batteries shall be
Global Yuhasa (Rocket)/ Panasonic / Exide. Minimum 2 years warranty from
date of commissioning of batteries & Inverters

SUB TOTAL

TOTAL FOR SECTION C

D SECTION D: EARTHING SYSTEM AND MISCELLANEOUS ITEMS

1 MAINTENANCE FREE EARTH PITS

a
Supply, installation testing & commissioning of Cu Bonded electrode Earth
station as per latest IS 3043 & technical specifications complete with 3000 mm
long, 25mm outer dia Molecular Copper bonded low carbon Steel rod earth
electrode, 150mm dia bore with wire mesh, earth flat clamp & test link. The Nos.
rate shall include excavation of earth, filling with 2 bags of back fill compound
per pit. 450mm x 450mm brick masonry chamber with vehicle heavy duty
chamber covers etc.

b Same as 1.a with 2000mm length Electrode rod. Nos. R0

2 GI EARTHING CONDUCTOR

Supply, laying and termination of the following sizes of earth flats and wires
laid underground at 600mm deep / on Cable trays/ drawn through pipe sleeves
along with column/ walls for safety earthing As per enclosed technical
specifications. All joints in the runs of the conductor shall be welded. All weld
joints shall be protected with bitumin paint. The equipment tape connections
shall be bolted using galvanized hardware.

a 75 x 8mm GI flat Mtrs.


b 50 x 6mm GI flat Mtrs.
c 40 x 6mm GI flat Mtrs.
d 25 x 6mm GI flat - Up to shaft Mtrs. 100
e 25 x 3mm GI flat Up to shaft Mtrs. 600
f
7 / 14 SWG GI Wire including terminations Up to near Dbearthing busbar. Mtrs. 400

g 7 / 16 SWG GI Wire including terminations Mtrs.


h 8 SWG GI wire including termination as required hardware Mtrs.
i.
25x6mm GI 600mm Long Bus bar with FRP Supporting insulator with suitable
Nos. 6
size of Brass coated Bolts and Nuts and suitable size of Grip Bolts

j.
25x6mm GI 300mm Long Bus bar with FRP Supporting insulator with suitable
Nos. 1
size of Brass coated Bolts and Nuts and suitable size of Grip Bolts

3 COPPER EARTHING CONDUCTOR

Supply, laying, jointing and termination of the following sizes of electrolytic


grade cu. Earth flats and wires laid underground/on Cable trays drawn through
pipe sleeves along with column/ walls for neutral/ESD/ dedicated earthing as
per drawings and technical specification. All joints in the run of copper
conductor shall be brazed or riveted. The equipment end connections shall be
bolted using passivated hardware.

a 40 x 6mm electrolytic grade copper strip in PVC sleeves. Mtrs.


b. 25 x 6mm electrolytic grade copper strip in PVC sleeves. Mtrs.
c. 25 x 3mm electrolytic grade copper strip in PVC sleeves. - Up to shaft. Mtrs. 400
d. 7 / 16 SWG GI Wire including terminations Mtrs.
e
40x6mm GI. 600mm Long Bus bar with FRP Supporting insulator with
Nos. R0
suitable size of Brass coated Bolts and Nuts and suitable size of Grip Bolts

f
25x6mm Copper 300mm Long Bus bar with FRP Supporting insulator with
Nos. 2
suitable size of Brass coated Bolts and Nuts and suitable size of Grip Bolts

g Earth Pit Marker grouted in Ground. Set R0

SUB TOTAL

2 MISCELLANEOUS ITEMS
2.1 MS Fabrication work carried out of M.S angle, plates and flats for fixing
of cable tray/pipe sleeves, DBs, etc., duly painted complete with
necessary hardware.
a 12mm dia Anchor fasteners Nos.
b 10mm dia Anchor fasteners Nos. 147
c 8mm dia Anchor fasteners Nos. 1400
d Galvanized M8 rod Hi-tech supports Mtrs. 1120
e Galvanized M10 rod Hi-tech supports Mtrs. 117
f Galvanized M12 rod Hi-tech supports Mtrs.
g ISMC channels / angles supporting structure for raceways, cable trays &
suspended lighting etc.The cost shall be including cutting, welding, painting Kgs R0
and necessary items to complete the work. .
h
5mm Thick, 25mm W G.I slotted channel supports for ceiling raceways. The
cost including making of 'L' or 'C' type supports for ceiling suspended trays
Mtrs. 200
installations .The cost shall be including cutting, welding, painting, installation
and necessary items to complete the work.

BOQ Page 8 of 11 RSP Design Consultants(I) Pvt. LTD


SI.NO DESCRIPTION UNIT QTY.

i 2mm Thick, 40mm W G.I slotted channel for ceiling raceways. The cost
including making of 'L' or 'C' type supports for raceway installation .The cost
Mtrs. 200
shall be including cutting, welding, painting installation, and necessary items to
complete the work.

2.2 SAFETY ACCESSORIES


Supply and installation of following safety accessories
a
1.1kV class-1 approved tested quality rubber mat of 6 mm thick and 900mm
wide and 1800mm long, installed in front of the power distribution boards and Nos. 10
other DBs (complied to latest IS and ISI Marked).

b A1 size drawing display board with laminated drawings Nos 6


Shock treatment chart in English and Local Language duly framed with glass
c Nos. 6
cover.
d 440V class enameled danger board of 150x150mm size. Nos. 6
g First aid box complete with all standard first aid materials. Nos. 1
h "NO ADMISSION" enameled board. Nos. 1
i Red colour painted, sand filled fire buckets with 1 no stand. Nos. 2

2.3 AS BUILT DRAWINGS


a Preparation of `As built drawings' on Auto-cad Release 2007 and submission
LS 1
of 6 blue prints with original & soft copy.
b Liaison with CEIG / MESCOM / Statutory bodies including preparation of
approval drawings & related documentation, this includes approval for interior LS 1
electrification works

2.4 FIRE BARRIERS AND WATER PROOFING MATERIALS


a 2-Hrs. rated fire barrier material HILTI Make or 3M Make or Equivalent Sq. M R0
b 10mm thick, MS chequered plate duly painted. Plates to be cut to size as
Sq. M R0
per site requirements and painted.
c 6mm thick, MS chequered plate duly painted. Plates to be cut to size as
Sq. M R0
per site requirements and painted.

e
10mm thick, SYNTEX make Hot pressed SMC moulded Chequered Plates.
Sq. M R0
Plate to be cut to size as required and installed after removing all sharp edges.

g
Fire barriers at wall / Floor crossing with Intuemescent sealant for sealing
small & medium size penetrations with 2 hour fire rated sealant as per the site
condition - Only HILTI / 3M make intuemescent sealant shall be used. Sq. M 4
The same shall be installed by authorized agency & the installation shall have
the manufacturers Certificate.

SUB TOTAL

TOTAL FOR SECTION D

GRAND TOTAL FOR SECTION A. B , C AND D

GENERAL CONDITIONS
Clients reserves to supply any listed items, the contractor shall install the
A
same at quoted installation price.
Clients reserves to change specification and makes of materials prior to
B
procurement by contractor.
All the execution shop drawings shall be prepared by vendor and approval
C shall be taken from Consultants/Architects/Clients before execution.

The sample of material used shall be provided by vendor as required for


D
approval of Consultants/Architects/Clients before procurement.
Incase any item required for quality execution is not included in tender BOQ,
E the same can be added by vendors with information to consultants, architects
& Clients.
If any items mentioned in BOQ/Specification has an impact on delivery for
completion of project with respect to time lines mention in contract, shall be
F informed to Architects/Consultants /Clients and take an approval for alternate
make.
G Contractor shall be submitt Cable schedule with Cable Tag Details.

BOQ Page 9 of 11 RSP Design Consultants(I) Pvt. LTD


preamble

PREAMBLE TO BILL OF QUANTITIES

shall be inclusive of all


The tenderer shall carefully go through the tender documents and quote the unit price which
installation accessories & consumables. No extra amount will be paid for any incidental, contingent
A work and materials.

The quantities indicated cover the probable quantities of work involved. The quantities are indicated for the guidance of the bidder.
The order arising out of this enquiry will be an unit rate contract & not a lump sum one. The Owner, however, does not in any way
B guarantee that the actual work involved would correspond to the quantities indicated in the tender.

C No change in unit rate will be allowed for any change in quantity, or for any other reason whatsoever.

D The rates quoted for the "Supply" items shall be include all taxes, packing, forwarding, freight, insurance & unloading charges.

The installation charges shall be inclusive of the cost of shifting materials to the installation spot, unpacking, installation on
E foundations as specified elsewhere, supply of hardware, consumables and any minor civil works involved.

The installation rate of all LT switchboards shall include the cost of fixing bolts & nuts, painting of cable sizes, fixing of nameplates,
F danger boards, testing & commissioning.

The rate for installation of earthing grid conductors shall include the cost of welding/ riveting & brazing of the joints, protecting the
G same against corrosion at joints, drilling holes for equipment terminations, cost of lugs for earthing wires and supply of hardware.

H All testing charges for the Equipment shall be included n the installation rate of the respective equipment.

The installation rate for cables shall include shifting of cable drums, unwinding & laying as per engineering standards all labor
supervision, routine testing, supply of consumables and installation materials such as identification tags, clamps etc. However,
the cost shall exclude steel supports, installation of trays and cable termination as also the excavation, backfilling, supply of
I protective covers, sand, bricks etc. which be quoted separately under the appropriate item.

The cost of excavation, supply of sand, bricks, back filling and supply of cable markers etc shall not be included in the cost of cable laying and
J same shall be covered under appropriate headings in the BOQ

The supply rate quoted for cable termination shall include heavy duty single compression brass cable gland, crimping type heavy
duty tinned copper lugs & earth tag for gland earthing. The installation rate shall include all consumables and Labor for preparation
K of cable, glanding & crimping.

The supply price of power wiring shall include the cost of FRLS grade wires, crimping type lugs for termination, Conduit, all conduit
L accessories such as bends, junction boxes, draw boxes etc., as per the specification.

The installation rates for concealed conduits shall include the cost of chasing the walls to appropriate depth to provide 20mm cover.
Installing the conduits with clamps in the wall recess and rough plastering the surface using cement mortar of specified mix to bring
M the wall surface to the original level. The final finishing shell however be carried out by other agencies.

The installation price of wiring shall include the cost of all necessary consumable required for fixing drawing, the wires and
N terminating the same with ferrules, sleeves etc.

The installation rate of cable trays shall exclude tray supports but shall include necessary clamp/ hardware required for fixing it
O on tray supports.

The installation rate for recess mounted luminaire shall include all the above and the cost of the GI suspension chain and alignment
P of luminaries.

The cost of steel frame work & supporting structure, required for the Switchboards / bus duct/ cable tray etc., shall be quoted under
Q the heatd Supply and Installation' of supporting steel.

The point wiring rate for luminaires shall include supply of all materials starting from passivated metal switchbox, junction boxes,
switch plate, switches, conduits & accessories, wires, tags, earthing the switchbox, earthing of luminaires etc. and no extra claim will
be allowed under any circumstances. The cost of suspension conduits, flexible PVC conduits, wires as required shall be included.
The point wiring rates of *ceiling fans shall include the supply of fan hook boxes in the case of recessed wiring and hooks in the case
R of surface wiring.

Page 10
preamble

The installation price of industrial power socket outlets shall include all necessary hardware & consumables required for mounting
S it on the surface of the wall/ column or concealing the same in walls.

Installation rate for pipe sleeves/ conduits shall cover necessary chasing in the floor/ walls etc., excavation if any and backfilling
T and rough plastering if required.

U The installation cost of surface mounted luminaires shall include the following
I Assembling the luminaire and checking the same.
ii Supply & installation of anchor fastners as required for the supports.
iii Installation of luminaire using appropriate hardware.
iv Wiring connection and installation of lamps.
V Testing & commissioning.

Any item not specifically mentioned in this specification & BOQ but considered essential for satisfactory operation of the system
shall be included by the tenderer in his offer. NO EXTRA AMOUNT WHATSOEVER WILL BE PAID FOR ANY CONTINGENT
V SUPPLY OR INSTALLATION WORK.

Page 11

You might also like