You are on page 1of 10

Clarion Co., Ltd. Published by Service Dept.

Export Division - 22-3, Shibuya 2-chome, Shibuyaku, Tokyo, 150-8335 Japan Tel: 03-3400-1121 298-5688-01 Sep.2000 P
Service Dept.- 50 kamitoda,Toda-shi,Saitama,335-8511 Japan Tel: 048-443-1111 FAX:048-433-6996 Printed in Japan

Service Manual
NISSAN Automobile Genuine
6 DISC COMPACT CHANGER

Model PN-2144A-A
from S/No.212177
(Genuine N0. 28184-4H000)

Model PN-2144D-A
from S/No.214177
(Genuine N0. 28184-2Y000)

Model PP-2144H-A
from S/No.15601
(Genuine N0. 28184-VB000)

Model PP-2144H-B
from S/No.17151
(Genuine N0. 28184-VB700)

REISSUE NOTIFICATION / NOTE


We cannot supply PWB with component parts in prin-
REPLACEMENT REQUEST ciple. When a circuit on PWB has failure , please repair
it by component parts base. Parts which are not men-
ORIGINAL SERVICE MANUAL tioned in service manual are not supplied.
This additional service manual is designed to be used to- Prevent damage caused by static electricity when re-
gether with pairing the pick-up.
The pattern of the pick-up is short-circuiting for preven-
Original model Manual No.
tion.
PN-2144A,D/PP-2144H 298-5688-00
Remove the soldering with a solder iron whose insula-
tion resistance is larger than 10M(DC500V) after com-
SPECIFICATIONS plete connection to the main PWB
Sampling frequency: 44.1kHz For repair table shall use copper or conductive sheet
Frequency response: 5Hz to 20kHz (1dB) (with impedance is lower to 100M from 1M)such as
Signal to noise ratio: 105dB (1kHz) IHF.A a sheet.
Wow and flutter: below measurement limits Be sure to put on a wrist-strap for prevent electric
Power supply: DC14.4V (10.8V to 15.6V) static's.(with impedance is to 100M from 1M) The
negative ground strap works to drain away the static electricity build-up
Current consumption: Less than 1A on the human body.
Weight: 3.8lb. (1.7kg) And as static electricity build-up on clothes is not drained
away, be careful and not your clothes to touch the pick-
Specification and design are subject to change without up.
notice for further improvement.

-1- PN-2144A/D
PP-2144H
5. Cautions regarding chips.
Position of short soldering for pick-up protection posi-
Do not reuse removed chips even when no abnormality is
tion is different by model.
observed in their appearance. Always replace them with
Some units have two short soldering points.
new ones. (The chip parts include resistors, capacitors,
Always short LD circuit to open the short circuit and re-
diodes, transistors, etc). The negative pole of tantalum
moves by soldering iron.
capacitors is highly susceptible to heat, so use special
care when replacing them and check the operation after-
COMPONENTS wards.
PN-2144A-A/D-A 6. Cautions in handling flexible PWB
Main unit 1 Before working with a soldering iron, make sure that the
Lock pin 331-2241-00 1 iron tip temperature is around 270. Take care not to ap-
Lock pin 331-2241-10 1 ply the iron tip repeatedly(more than three times)to the
PP-2144H-A/B same patterns. Also take care not to apply the tip with
force.
Main unit 1
7. Turn the unit OFF during disassembly and parts replace-
Lock pin 331-2241-00 1
ment. Recheck all work before you apply power to the unit.
Lock pin 331-2241-10 1
8. Cautions in checking that the optical pickup lights up.
The laser is focused on the disc reflection surface through
the lens of the optical pickup. When checking that the la-
To engineers in charge of repair or ser optical diode lights up, keep your eyes more than
30cms away from the lens. Prolonged viewing of the laser
inspection of our products. within 30cms may damage your eyesight.
Before repair or inspection, make sure to follow 9. Cautions in handling the optical pickup
the instructions so that customers and Engineers The laser diode of the optical pickup can be damaged by
in charge of repair or inspection can avoid suf- electrostatic charge caused by your clothes and body.
Make sure to avoid electrostatic charges on your clothes
fering any risk or injury. or body, or discharge static electricity before handling the
1. Use specified parts. optical pickup.
The system uses parts with special safety features against 9-1. Laser diode
fire and voltage. Use only parts with equivalent charac- The laser diode terminals are shorted for transpor-
teristics when replacing them. tation in order to prevent electrostatic damage.
The use of unspecified parts shall be regarded as re- After replacement, open the shorted circuit.
modeling for which we shall not be liable. The onus of When removing the pickup from the mechanism,
product liability (PL) shall not be our responsibility in cases short the terminals by soldering them to prevent this
where an accident or failure is as a result of unspecified damage.
parts being used. 9-2. Actuator
2. Place the parts and wiring back in their original positions The actuator has a powerful magnetic circuit. If a
after replacement or re-wiring. magnetic material is put close to it. its characteris-
For proper circuit construction, use of insulation tubes, tics will change. Ensure that no foreign substances
bonding, gaps to PWB, etc, is involved. The wiring con- enter through the ventilation slots in the cover.
nection and routing to the PWB are specially planned us- 9-3. Cleaning the lens
ing clamps to keep away from heated and high voltage Dust on the optical lens affects performance. To
parts. Ensure that they are placed back in their original clean the lens, apply a small amount of isopropylalcohol
positions after repair or inspection. to lens paper and wipe the lens gently.
If extended damage is caused due to negligence during
repair, the legal responsibility shall be with the repairing
company.
3. Check for safety after repair.
Check that the screws, parts and wires are put back se-
curely in their original position after repair. Ensure for
safety reasons there is no possibility of secondary
ploblems around the repaired spots.
If extended damage is caused due to negligence of re-
pair, the legal responsibility shall be with the repairing
company.
4. Caution in removal and making wiring connection to the
parts for the automobile.
Disconnect the battery terminal after turning the ignition
key off. If wrong wiring connections are made with the
battery connected, a short circuit and/or fire may occur.
If extensive damage is caused due to negligence of re-
pair, the legal responsibility shall be with the repairing
company.

PN-2144A/D -2-
PP-2144H
EXPLANATION OF IC
052-5024-21 PD78053GC-A96-8BT CD A/C Controller pin 53 : NU : - : Not in use.
pin 54 : NU : - : Not in use.
1. Terminal Description pin 55 : NU : - : Not in use.
pin 1 : CLAMP ON_ : IN : Clamp ON signal input. Negative logic. pin 56 : NU : - : Not in use.
pin 2 : LOD TR2_ : IN : "H"= 12cm disk, "L"= The disk is pin 57 : NU : - : Not in use.
stored in the holder.
pin 58 : NU : - : Not in use.
pin 3 : LOD TR1_ : IN : "H"= The disk presents in the holder.
"L"= The holder stored in the maga- pin 59 : NU : - : Not in use.
zine. pin 60 : RESET_ : IN : Reset signal input. Negative logic.
pin 4 : A VSS : - : Analog ground. pin 61 : SCOR : IN : Inputs a high signal from CD IC when
pin 5 : POS SW : IN : Datum point signal input to detect the either subcode sync S0 or S1 is de-
disc number. tected.
pin 6 : D No TR_ : IN : Disk number detect pulse input. Nega- pin 62 : ACC DET_ : IN : ACC detection terminal. "L"= ACC ON.
tive logic. pin 63 : MG SW_ : IN : L= the magazine has been inserted.
pin 7 : A Vref 1 : - : Reference voltage for the internal ADC. pin 64 : MG EJ_ : IN : Eject key signal input. Negaive logic.
pin 8 : RXD_ : IN : Data input terminal of ACP Bus. Nega- pin 65 : NU : - : Not in use.
tive logic. pin 66 : NU : - : Not in use.
pin 9 : TXD_ : O : Data output of ACP Bus. Negative log- pin 67 : NU : - : Not in use.
ic.
pin 68 : VDD : - : Positive supply voltage for the digital
pin 10 : REQ : O : ACP Bus request signal output. part.
pin 11 : SQ SO : IN : Serial data input to read out SUB-Q- pin 69 : X 2 : O : Ceramic resonator connection.
data from CXD2548. Negative logic.
pin 70 : NU : - : Not in use.
pin 12 : NU : - : Not in use.
pin 71 : NU : - : Not in use.
pin 13 : SQ CK : O : Clock pulse output to read SUB-Q -
Data from CDX2548. pin 72 : NU : - : Not in use.
pin 14 : NU : - : Not in use. pin 73 : NU : - : Not in use.
pin 15 : NU : - : Not in use. pin 74 : A VDD : - : Positive supply voltage for the Analog
section.
pin 16 : NU : - : Not in use.
pin 75 : A Vref 0 : - : Reference voltage for the internal ADC.
pin 17 : NU : - : Not in use.
pin 76 : NU : - : Not in use.
pin 18 : NU : - : Not in use.
pin 77 : T CLK : O : "Test mode display" clock output.
pin 19 : NU : - : Not in use.
pin 78 : HOLD IN_ : IN : "L"= The magazine is charged.
pin 20 : NU : - : Not in use.
pin 79 : HOLD OUT_ : IN : "L"= The magazine is discharged.
pin 21 : NU : - : Not in use.
pin 80 : CLAMP OFF_ : IN : Clamp OFF signal input. Negative log-
pin 22 : NU : - : Not in use. ic.
pin 23 : NU : - : Not in use.
pin 24 : NU : - : Not in use.
Table 1. Loading motor control signal output
pin 25 : NU : - : Not in use. Load Unload Brake Stop
pin 26 : NU : - : Not in use. LD CW ( pin40 ) L H H L
pin 27 : A MUTE : O : Audio mute signal output. LD CCW ( pin41 ) H L H L
pin 28 : D STOP : O : Digital output control. Outputs "H" at
Play.
pin 29 : NU : - : Not in use. Table 2. Up/down motor control signal output
pin 30 : P ON 1 : O : Power ON signal output. Up Down Brake Stop
pin 31 : P ON 2 : O : Power ON signal output. UD CW ( pin43 ) H L H L
pin 32 : NU : - : Not in use. UD CCW ( pin42 ) L H H L
pin 33 : VSS : - : Negative supply voltage.
pin 34 : NU : - : Not in use.
pin 35 : NU : - : Not in use.
pin 36 : NU : - : Not in use.
pin 37 : NU : - : Not in use.
pin 38 : NU : - : Not in use.
pin 39 : NU : - : Not in use.
pin 40 : LD CW : O : Loading motor control signal output.
Ref. Table 1.
pin 41 : LD CCW : O : Loading motor control signal output.
Ref. Table 1.
pin 42 : UD CCW : O : Up/down motor control signal output.
Ref. Table 2.
pin 43 : UD CW : O : Up/down motor control signal output.
Ref. Table 2.
pin 44 : PWM 1 : O : Spindle motor control out.
pin 45 : X RST_ : O : Reset pulse output to CXD2548.
pin 46 : CLOCK OUT : O : Serial data transfer clock output.
pin 47 : X LAT : O : Latch signal output terminal of serial
data communication line.
pin 48 : DATA : O : Serial data output to the CD IC.
pin 49 : S CLK : O : Clock pulse output to the CD IC, to
read the SENS data.
pin 50 : SENS : IN : Serial status data input from the CD
IC.
pin 51 : SYSM : O : Mute signal output.
pin 52 : NU : - : Not in use.

-3- PN-2144A/D
PP-2144H
BLOCK DIAGRAM

PN-2144A/D -4-
PP-2144H
EXPLODED VIEWPARTS LIST
Main section

Note)Some parts depend on each model.The model name is specified in the description.

NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 MECHA.MODULE(10210/1-929) 1 18 854-7536-13 EXTENSION LEAD(PN-2144A-A) 1
854-7536-11 EXTENSION LEAD(PN-2144D-A)
2 039-0959-03 CONNECT PWB 1 854-7536-11 EXTENSION LEAD(PP-2144H-A)
(WITHOUT COMPONENT) 854-7536-13 EXTENSION LEAD(PP-2144H-B)
3 310-1620-04 UPPER CASE 1 19 331-2288-00 LEAD HOLDER 1
4 311-1702-06 LOWER CASE 1 20 335-0833-05 LEAD HOLDER 1
5 320-0539-11 DUSTPROOF CVR 1 21 286-9086-01 SETPLATE(PN-2144A-A) 1
286-9086-00 SETPLATE(PN-2144D-A)
6 320-0540-08 DUSTPROOF CVR 1 286-8964-00 SETPLATE(PP-2144H-A)
286-8964-01 SETPLATE(PP-2144H-B)
7 370-5672-07 ESCUTCHEON 1
22 347-5476-00 INSULATOR 1
8 371-3892-03 TRIM PLATE 1
23 285-1691-00 GUIDE LABEL(PP-2144H-A/B) 1
9 382-4518-00 BUTTON 1
24 285-1426-00 GUIDE LABEL(PP-2144H-A/B) 1
10 620-0726-02 DAMPER PLATE FRONT 1
25 285-1633-00 GUIDE LABEL(PP-2144H-A/B) 1
11 620-0727-01 DAMPER PLATE REAR 1
26 347-5088-00 MASK PAPER 1
12 622-1332-01 F-PLATE PIN 1
27 347-5654-00 LABEL(PP-2144H-A/B) 1
13 622-1344-01 F-PIN SR 1
28 335-5653-01 SPACER 1
14 629-0060-00 DAMPER 4
29 335-5025-00 CLIP(PP-2144H-A) 1
15 716-1716-00 SPECIAL SCREW 12
30 335-5376-00 CLIP(PP-2144H-A/B) 1
16 750-3242-00 FL SPRING F 1
31 335-5993-00 LOCK FASTENER(PN-2144D-A) 1
17 750-3243-00 FL SPRING R 1

-5- PN-2144A/D
PP-2144H
CD mechanism module section

NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 966-0480-00 REAR PANEL-ASSY 1 20 621-0377-00 V-HELICAL GEAR 1
2 966-0460-05 V-CHASSIS-ASSY 1 21 621-0423-00 V-GEAR A 1
3 966-0461-01 UD-GEAR-P-ASSY 1 22 621-0380-01 MAGAZINE RAIL 1
4 966-0484-11 MG-LO-P-ASSY-S 1 23 629-0061-00 GEAR DAMPER 1
5 966-0463-04 UP-PLATE-ASSY-S 1 24 714-2006-81 MACHINE SCREW (M26) 1
6 LOADING UNIT 1 25 716-1468-00 SCREW (M22) 15
7 039-1194-00 LOADING UNIT PWB 1 26 716-1716-00 SCREW (M23) 3
(WITHOUT CMPONENT)
27 716-1799-00 SCREW(M22.5) 1
8 039-1002-01 MAIN PWB 1
(WITHOUT CMPONENT) 28 743-1500-20 E-RING 3
9 SMA-155-100 MOTOR-ASSY 1 29 743-2000-20 E-RING 1
10 610-0367-00 PUSH P ROLLER 1 30 746-0761-00 WASHER (2.0) 2
11 620-0705-02 MG-EJ-PLATE 1 31 750-3238-00 MG-L-SPRING-S 1
12 620-0707-00 HEAT SINK 1 32 750-3239-00 MG-EJ-SPRING-S 1
13 620-0710-00 SLIDE PLATE-L-S 1 33 750-3244-00 HOLD SPRING 1
14 620-0711-01 SLIDE PLATE-S 1 34 750-3247-00 PO-SW-SPRING 1
15 620-0793-00 SIDE PANEL-F 1 35 750-3249-00 GAP SPRING-R 1
16 620-0824-00 GAP PLATE-R 1 36 800-4910-60 WIRE (BLK) 1
17 620-0733-00 PO-SW-PLATE 1 37 802-4910-60 WIRE (RED) 1
18 620-0734-00 HOLD PLATE-L 1 38 347-5590-00 PAPER 1
19 746-0904-00 WASHER(2.2) 1

PN-2144A/D -6-
PP-2144H
Loading unit section

NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 966-0457-06 L-CHASSIS ASSY 1 20 621-0386-01 CAM GEAR 1
2 966-0458-01 LOCK ARM ASSY 1 21 621-0387-01 HOLDER G-RAIL-L 1
3 966-0464-00 CLAMP SE-ASSY 1 22 621-0388-10 HOLDER G-RAIL-R 1
4 SMA-154-200 MOTOR ASSY (LD) 1 23 622-1330-00 CAM G-ROLLER 1
5 966-0468-00 SIDE PUSH-ASSY 1 24 716-1468-00 SCREW(M22.5) 8
6 968-0100-03 DRIVE UNIT 1 25 716-1716-00 SCREW(M23) 5
7 039-1194-00 LOADING UNIT PWB 1 26 744-0039-00 E-RING 1
(WITHOUT CMPONENT)
27 745-0748-01 WASHER(3.02.7 t0.06) 1
8 750-3367-11 SW-PLATE SPRING 1
28 746-0761-00 WASHER(1.6 t0.25) 3
9 743-1500-20 E-RING 1
29 746-0762-00 WASHER(1.6 t0.5) 1
10 610-0369-00 HOLDER S-ROLLER 1
30 750-3240-00 LOCK ARM SPRING 1
11 620-0713-10 CLAMP SW-PLATE 1
31 750-3245-00 GAP L-SPRING 1
12 620-0715-02 HOLDER SHIFT-PL 1
32 750-3246-00 LOCK L-SPRING 1
13 620-0717-01 MOTOR PLATE 1
33 750-3259-00 SIDE P-SPRING 1
14 620-0719-12 SWITCH PLATE 1
34 750-3261-00 SWING SPRING 1
15 802-4906-60 VINYL COAT WIRE(RED) 1
35 800-4906-60 VINYL COAT WIRE(BLK) 1
16 621-0382-00 LO-HELICAL GEAR 1
36 039-0923-01 PICKUP FPC 1
17 621-0383-00 LOADING GEAR 1 (WITHOUT CMPONENT)
18 621-0384-00 SWING GEAR 1 37 039-1386-00 LOAD D-FPC(PN-2144D-A) 1
039-0924-01 LOAD D-FPC(Other)
19 621-0385-00 PACK PINON 1 (WITHOUT CMPONENT)

-7- PN-2144A/D
PP-2144H
Drive unit section

NO. PART NO. DESCRIPTION Q'TY NO. PART NO. DESCRIPTION Q'TY
1 966-0454-00 SH-RACK ASSY 1 17 803-4908-60 VINYL COAT WIRE(ORG) 1
2 966-0456-05 DRIVE PL-ASSY 1 18 621-0389-01 MOTOR HOLDER 1
3 969-0006-01 PICK UP UNIT 1 19 621-0390-00 PICK UP GUIDE 1
4 013-3953-01 SWITCH 1 20 621-0391-02 SCREW HOL-BASE 1
5 SMA-146-100 MOTOR ASSY (SL) 1 21 621-0392-01 LS-HOLDER-R 1
6 SMA-156-200 MOTOR ASSY (SP) 1 22 624-0017-10 LEAD SCREW 1
7 039-0923-01 FPC(WITHOUT CMPONENT) 1 23 716-0484-10 SCREW(M22.5) 1
8 039-0926-00 DRIVE UNIT PWB 1 24 716-0675-00 SCREW(M25.5) 2
(WITHOUT CMPONENT)
25 716-1716-00 SCREW(M23) 5
9 620-0721-00 CLAMP ARM 1
26 716-1733-00 SCREW(M1.72.3) 2
10 620-0791-00 L-UPPER PLATE 1
27 732-2004-11 LEAD SCREW(M24) 2
11 620-0723-01 SCREW PUSH PLT 1
28 739-1735-17 PRECISION SCREW(M1.73.5) 2
12 620-0724-00 CLAMPER PLATE 1
29 739-2020-17 PRECISION SCREW(M22) 2
13 621-0205-02 CLAMPER RING 1
30 743-1500-20 E-RING 2
14 801-4910-60 VINYL COAT WIRE(BRN) 1
31 750-3241-00 CLAMP A SPRING 1
15 621-0255-02 SECOND GEAR 1
16 621-0256-01 LS-GEAR 1

PN-2144A/D -8-
PP-2144H
ELECTRICAL PARTS LIST
Note) Several different parts of the same reference number are alternative parts.
Main PWB section (B1) One of those parts is used in the set.
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
C101 178-1042-78 0.1F C436 178-4722-78 4700pF Q112 125-2004-02 RN1402
C102 184-4773-31 16V470F C443 176-1511-00 150pF CH Q112 125-2031-02 MUN2211
C103 173-1021-11 1000pF J C446 178-1042-78 0.1F Q201 103-1306-00 2SD1306
C104 178-1032-78 0.01F C501 178-1032-78 0.01F Q201 103-1328-00 2SD1328
C105 042-0452-01 10V220F C502 172-1041-11 0.1F Q202 103-1306-00 2SD1306
C106 178-1032-78 0.01F C503 178-3332-78 0.033F Q202 103-1328-00 2SD1328
C107 042-0452-01 10V220F C504 178-1032-78 0.01F Q203 103-1306-00 2SD1306
C108 178-1032-78 0.01F C505 183-3353-61 50V3.3F Q203 103-1328-00 2SD1328
C109 183-1073-12 6.3V100F C602 178-1022-78 1000pF Q204 103-1306-00 2SD1306
C110 183-1073-12 6.3V100F D101 001-0466-00 S5688B Q204 103-1328-00 2SD1328
C111 183-1063-31 16V10F D102 001-0377-47 MA4091M Q209 100-1162-00 2SA1162
C112 178-1032-78 0.01F D102 001-0376-48 MTZJ9.1C Q209 100-1037-00 2SA1037
C113 178-1032-78 0.01F D102 001-0400-47 HZS9.1JB2 Q210 125-2004-02 RN1402
C114 178-1032-78 0.01F D103 001-0377-45 MA4082H Q210 125-2031-02 MUN2211
C115 178-1032-78 0.01F D103 001-0376-46 MTZJ9.1A Q401 101-1188-50 2SB1188PQR
C116 178-1032-78 0.01F D103 001-0400-45 HZS8.2JB3 Q603 102-2712-00 2SC2712
C117 178-1032-78 0.01F D104 001-0377-31 MA4056L Q603 103-0601-00 2SD601
C118 183-1063-31 16V10F D104 001-0376-31 MTZJ5.6A Q604 102-2712-00 2SC2712
C201 183-3363-21 10V33F D104 001-0400-31 HZS5.6JB1 Q604 103-0601-00 2SD601
C202 183-3363-21 10V33F D105 001-0330-00 1SS119 Q605 125-0014-02 DTA114EK
C203 176-3301-00 33pF CH D106 001-0503-33 HZS6B2L Q605 125-0024-02 MUN2111
C204 176-3301-00 33pF CH D301 001-0377-33 MA4056H Q606 102-2712-00 2SC2712
C205 178-1032-78 0.01F D301 001-0376-34 MTZJ6.2A Q606 103-0601-00 2SD601
C206 176-2201-00 22pF CH D301 001-0400-33 HZS5.6JB3 Q607 125-2004-02 RN1402
C207 176-2201-00 22pF CH D302 001-0377-39 MA4068H Q607 125-2031-02 MUN2211
C208 172-1041-11 0.1F D302 001-0376-40 MTZJ7.5A R101 117-5611-10 1/10W 560
C209 183-1073-12 6.3V100F D302 001-0400-39 HZS6.8JB3 R102 111-2211-81 1/2WS 220
C210 042-0452-01 10V220F D303 001-0563-00 GL380 R103 111-1001-81 1/2WS 10
C211 042-0452-01 10V220F D304 001-0563-00 GL380 R104 117-1211-10 1/10W 120
C212 042-0452-01 10V220F D401 001-0330-00 1SS119 R105 117-1531-10 1/10W 15k
C213 042-0452-01 10V220F D501 001-0466-00 S5688B R106 117-1021-10 1/10W 1k
C221 178-5612-78 560pF D603 001-0330-00 1SS119 R107 117-2231-10 1/10W 22k
C222 178-5612-78 560pF D604 001-0330-00 1SS119 R108 117-4711-10 1/10W 470
C223 178-5612-78 560pF D607 001-0421-38 MTZJ36 R109 117-5611-10 1/10W 560
C224 178-5612-78 560pF D608 001-0421-38 MTZJ36 R201 117-1031-10 1/10W 10k
C301 178-1032-78 0.01F D609 001-0330-00 1SS119 R202 117-1031-10 1/10W 10k
C302 178-1032-78 0.01F FIL603 060-3101-05 NFM39R12C102B1 R203 117-1531-10 1/10W 15k
C303 183-1063-31 16V10F FIL604 060-3101-05 NFM39R12C102B1 R204 117-1531-10 1/10W 15k
C304 178-1032-78 0.01F FIL605 060-3101-05 NFM39R12C102B1 R205 117-1031-10 1/10W 10k
C305 178-1032-78 0.01F IC201 051-3005-00 NJM4556AD R206 117-1031-10 1/10W 10k
C402 178-1032-78 0.01F IC202 051-3005-00 NJM4556AD R207 117-1031-10 1/10W 10k
C403 178-6812-78 680pF IC301 051-1408-00 LB1649 R208 117-1031-10 1/10W 10k
C404 176-1501-00 15pF CH IC302 051-6015-05 BA6392FP R209 117-8221-10 1/10W 8.2k
C405 176-1501-00 15pF CH IC401 051-6318-00 CXD2548R R210 117-1031-10 1/10W 10k
C406 178-1032-78 0.01F IC402 051-5703-00 CXA1791M R211 117-2201-10 1/10W 22
C407 176-1511-00 150pF CH IC501 052-5024-21 PD78053GC-A96- R212 117-2201-10 1/10W 22
C408 178-6812-78 680pF 8BT R213 117-2201-10 1/10W 22
C409 178-1032-78 0.01F IC502 051-5806-00 GP1S94 R214 117-2201-10 1/10W 22
C410 178-4745-79 0.47F IC503 051-0869-55 NJM2103M R215 117-1031-10 1/10W 10k
C412 178-4745-79 0.47F J101 074-1138-63 13P R216 117-1031-10 1/10W 10k
C413 176-1007-00 10pF CH J102 074-1138-65 15P R217 117-1031-10 1/10W 10k
C416 178-4732-78 0.047F J103 074-1158-69 19P R218 117-1031-10 1/10W 10k
C417 178-1522-78 1500pF L401 010-2155-93 10H R219 117-2221-10 1/10W 2.2k
C418 178-1042-78 0.1F Q101 103-1683-50 2SD1683ST R220 117-2221-10 1/10W 2.2k
C419 178-1032-78 0.01F Q102 125-0014-02 DTA114EK R221 117-2221-10 1/10W 2.2k
C420 178-4745-79 0.47F Q102 125-0024-02 MUN2111 R222 117-2221-10 1/10W 2.2k
C421 178-1032-78 0.01F Q103 125-2004-02 RN1402 R229 117-1031-10 1/10W 10k
C422 178-2212-78 220pF Q103 125-2031-02 MUN2211 R230 117-1031-10 1/10W 10k
C423 178-1042-78 0.1F Q104 103-1683-50 2SD1683ST R301 117-1031-10 1/10W 10k
C424 178-2212-78 220pF Q105 125-0014-02 DTA114EK R302 117-8231-10 1/10W 82k
C425 178-4722-78 4700pF Q105 125-0024-02 MUN2111 R303 117-1811-10 1/10W 180
C426 178-1032-78 0.01F Q106 125-2004-02 RN1402 R401 117-1231-10 1/10W 12k
C427 183-3363-21 10V33F Q106 125-2031-02 MUN2211 R402 117-1231-10 1/10W 12k
C428 178-1032-78 0.01F Q107 103-1858-00 2SD1858 R403 117-1231-10 1/10W 12k
C429 178-1032-78 0.01F Q108 103-1858-00 2SD1858 R404 117-4711-10 1/10W 470
C430 183-3363-21 10V33F Q109 100-1048-00 2SA1048 R405 117-1231-10 1/10W 12k
C431 183-3363-21 10V33F Q109 100-1175-00 2SA1175 R406 117-1231-10 1/10W 12k
C432 176-3901-00 39pF CH Q110 125-2004-02 RN1402 R407 117-1231-10 1/10W 12k
C433 176-2096-00 2pF CJ Q110 125-2031-02 MUN2211 R408 117-1041-10 1/10W 100k
C434 178-1032-78 0.01F Q111 125-0014-02 DTA114EK R409 117-3331-10 1/10W 33k
C435 183-1073-12 6.3V100F Q111 125-0024-02 MUN2111 R413 117-3321-10 1/10W 3.3k

-9- PN-2144A/D
PP-2144H
REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
R414 117-6821-10 1/10W 6.8k R460 117-1021-10 1/10W 1k R514 117-4731-10 1/10W 47k
R415 117-1031-10 1/10W 10k R461 117-1021-10 1/10W 1k R515 117-4731-10 1/10W 47k
R416 117-1051-10 1/10W 1M R462 117-1021-10 1/10W 1k R516 117-4731-10 1/10W 47k
R417 117-1041-10 1/10W 100k R463 117-1021-10 1/10W 1k R517 117-4731-10 1/10W 47k
R418 117-1031-10 1/10W 10k R464 117-1021-10 1/10W 1k R518 117-1031-10 1/10W 10k
R419 117-3631-10 1/10W 36k R466 117-1021-10 1/10W 1k R519 111-2221-91 1/4WS 2.2k
R420 117-1241-10 1/10W 120k R467 117-1021-10 1/10W 1k R520 117-5631-10 1/10W 56k
R421 117-3631-10 1/10W 36k R468 117-1021-10 1/10W 1k R521 117-1231-10 1/10W 12k
R422 117-6821-10 1/10W 6.8k R469 117-1021-10 1/10W 1k R601 117-5621-10 1/10W 5.6k
R423 117-3321-10 1/10W 3.3k R470 117-1021-10 1/10W 1k R606 117-5631-10 1/10W 56k
R424 117-1821-10 1/10W 1.8k R471 117-1021-10 1/10W 1k R613 117-1031-10 1/10W 10k
R425 117-1031-10 1/10W 10k R472 117-1021-10 1/10W 1k R614 117-1031-10 1/10W 10k
R426 117-2231-10 1/10W 22k R473 117-4721-10 1/10W 4.7k R615 117-1031-10 1/10W 10k
R427 117-5631-10 1/10W 56k R474 117-2231-10 1/10W 22k R616 117-1031-10 1/10W 10k
R428 117-1001-10 1/10W 10 R502 117-4731-10 1/10W 47k R617 117-4731-10 1/10W 47k
R429 117-1541-10 1/10W 150k R503 117-4731-10 1/10W 47k R620 117-5631-10 1/10W 56k
R430 117-9141-10 1/10W 910k R504 117-4731-10 1/10W 47k R621 117-5631-10 1/10W 56k
R431 117-1151-15 1/10W 1.1M R505 117-4731-10 1/10W 47k R901 117-2211-10 1/10W 220
R432 117-1541-10 1/10W 150k R506 117-1041-10 1/10W 100k R902 117-4731-10 1/10W 47k
R433 117-3331-10 1/10W 33k R507 117-4731-10 1/10W 47k S501 013-3989-00 SPPB63
R434 117-3331-10 1/10W 33k R508 117-2711-10 1/10W 270 S502 013-7204-00 SPPB64
R435 117-1011-10 1/10W 100 R509 117-1041-10 1/10W 100k S503 013-6100-10 SKHLLD
R436 117-4731-10 1/10W 47k R510 117-1041-10 1/10W 100k T101 009-0625-02 CHOKE
R457 117-1021-10 1/10W 1k R511 117-4731-10 1/10W 47k X401 061-3038-00 HC49 16.9344MHz
R458 117-1021-10 1/10W 1k R512 117-4731-10 1/10W 47k X501 060-0319-00 4.915MHz
R459 117-1021-10 1/10W 1k R513 117-4731-10 1/10W 47k

Loading unit PWB section (B2)


REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION REF No. PART No. DESCRIPTION
Q701 060-0252-01 PT4850F S701 013-3953-01 SPPB32 S703 013-3953-01 SPPB32
Q702 060-0252-01 PT4850F S702 013-3953-01 SPPB32 S704 013-3953-01 SPPB32

Drive unit PWB section (B3)


REF No. PART No. DESCRIPTION
S801 013-3953-01 SPPB32

PN-2144A/D - 10 -
PP-2144H

You might also like