You are on page 1of 5

http://www.icstation.

com

Muti_Function Perfect Version Delay Module H/L/NC/NO Trigger

Multi-function delay module, support high level trigger, low level trigger, Normally open
trigger(switch turn_on),Normally closed trigger(switch turn_off), also support rising edge pulse
trigger , support a variety of vibration sensors, reed pipe sensor, Angle sensors, a variety of
trigger sensor module, MCU trigger, etc., delay time range many choices, there are high and
low level output selection, is rarely a time delay module.

Product application:
arduino robot, intelligent product development, automation equipment, PLC, intelligent
household, door control anti-theft, electronic development and so on.
Specification:

m
1. Use double-sided FR-4 circuit boards, chip manufacturing process;

o
2. Perfect smart delay chip, voltage range wide, output delay stability;

c
3. Power section with increased electrolytic capacitor filtering, and anti-interference

.
capacitor to prevent unstable power supply delay module;

n
4. Power output with anti-power reverse the diode, the effective protection module;

io
5. Trigger port with optocoupler isolation, reliable performance and stability, to prevent

t
false triggering the occurrence of the trigger;

a
6. Delay output high/low level selection;

t
7. Has 8-types ranges choose the shortest 0.1 seconds, up to 1 hour, can meet the

s
requirements of most people in different time;

i c
8. Module with low power consumption.

.
Performance indicators:

w
1. Power requirements :4-12VDC
2. Power: 4-12mA (related to the power supply)

w
3. Drive capability: > 15mA
4. Environment temperature: 80 degrees

w
5. Delay Stability: Set a time, every time delay error is less than 1%.
6. Module size: 32 x 30 x 12mm
Module connection:
VCC: positive
GND: connect power anode
OUT: delay output (switch signal output, close to the power supply)
Module Trigger Introduce:
1. High level trigger (rising edge of the pulse): trigger level is greater than 4V, less than
12V trigger can be accessed by a variety of single-chip I/O port, the sensor module;
2. Low level trigger: trigger level is less than 1V to trigger the microcontroller used trigger
mode;
3. Normally open (switch ON) trigger wide range of applications: This trigger is used widely,
If the connection is vibration sensor, it can be as a delay alarm is triggered.If the connection is
magnetic door switch, it can be as a delay door control alarm.If the tilt switch, it can be tilted as
delay alarm;

1
http://www.icstation.com

4. Normally closed (switch is turned off, the circuit is disconnected) Trigger: commonly
used in the detection of the circuit, if circuit is break, it will trigger delay.
Delay range of options:
This module has 8 kinds of optional time range, the demand for different time, choose the
appropriate time scale can be achieved accurately, may refer to below how to select the time
range.
Output delay high/low level selection methods:
When the S3 connected with "1", the output port output high level during the delay
When the S3 connected with "0", the output port output low level during the delay
*******************************************************************************

o m
n. c
t io
s ta
. i c
*******************************************************************************

w
Trigger function

w
1. When the module response to the trigger signal. Module startup time delay function, the
relay is closed at the same time. After the delay, the relay is reset

w
t=t1+t2
t : delay time
t1 : trigger time
t2 : chip count time
*******************************************************************************
2. When the module in the trigger delay, if receive the trigger signal again, the module will start
timing, until the end of the time delay

2
http://www.icstation.com

t=t3+t2
t : delay time
t2 : chip count time
t3 : triggering time repeatedly and interrupt delay time
*******************************************************************************
Trigger mode selection
1. High level trigger (rising edge of the pulse):
trigger level is greater than 4V, less than 12V

m
trigger can be accessed by a variety of

o
single-chip I / O port, the sensor module;

n. c
io
*******************************************************************************

t
2. Low level trigger: trigger level is less than 1V to trigger

a
the microcontroller used trigger mode;

c s t
w. i
w
*******************************************************************************
3. Normally open switch (switch turn on) trigger mode selection,

w
as pictured, when trigger pins have a momentary signal for
switch closed, then delay can trigger module.

*******************************************************************************
4. Normally closed switch (switch turn off) trigger mode
selection, as pictured, when trigger pins form ON_state to
OFF_state, then delay can trigger module.

*******************************************************************************

3
http://www.icstation.com

Delay time range selection method


Changing-over the position of the switch S1/S2/S4, the potentiometer can be adjusted
by different time range

o m
n. c
t io
s ta
. i c
w
Output delay high/low level selection methods:

w
When the S3 connected with "1", the output port output high level during the delay

w
When the S3 connected with "0", the output port output low level during the delay
(as shown)
*******************************************************************************
Delay output module using method
1.High level delay output connecte to relay

*******************************************************************************

4
http://www.icstation.com

2.Low level delay output connect to relay

*******************************************************************************
3.Output connect to the I/O pin of micro controller or PLC

o m
n. c
t io
s ta
. i c
*******************************************************************************

w w
w

You might also like